Urgent help: HTS P3300 stuck up - P3300, MDA Compact III General

Dear All,
Please urgent help required.
my HTC P3300 (Artemis) stuck up when i was trying to start it up. when i use to turn my cell on, i goes to the starting screen shows the following numbers and then stuck up.
IPL 3.07.0001
SPL 3.07.0000
GSM 02.69.90
OS 3.7.0.0
the screen does not move after that. i tried soft reset through the reset button but result is the same.
i also tried hard reset and when i puch the green phone button to proceed, a message come "FORMAT FAILED" and the phone stucks up.
i am quite a lot of problems since i have upgraded to WM6 from WM5 last week.
i am quite sucked with this problem. not been able to use my set since yesterday.
please also note that my HTC was not syncing with my PC since i have upgraded to WM6.
PLEASE HELP URGENTLY.
Nomi

HTC P3300
Follow this link and have a deep read
http://wiki.xda-developers.com/index.php?pagename=HTC_Artemis

Related

Rom Upgrade Problems

Hi, I have upgraded my Qtek 9000 Rom WWE with a PTB version.
Now, my phone only show the "USB v1.0" screen...
Is the 4th time that i'm trying to do this again, and it still doen't boot up to the Windows Mobile, only the "USB v1.0" screen.
I have tried hard resets and it still on "Serial v1.0" screen...
Please someone help me!
http://forum.xda-developers.com/viewtopic.php?t=43592
Worked using a diferent radio Rom. Thanks.

Problem with softbank X01HT

can anyone help me? Im new with PDA. What happen was i tried to upgrade my PDA, and i manage to install the satin black. after trying another os my pda doesn't want to reboot when the installation was succesful. tried hard reboot and it goes to the red green yellow and white screen. now everytime i get the spl 1.40 to install it works till 100% but after that it won't reboot. what can i do? thx. please help
you should hard spl your x01ht first before upgrading your pda.
did you do hard spl first?
what is your radio rom, SPL??

Need help ! cingular 8125 bricked :(

Hey iam new to this upgrading,CID unlocking etc.
I just bought my Cingular 8125 three weeks before.
I tried upgrading to WM 6.0 The update process completed successfully but after the reboot my mobile was back to factory default with wm 5.0.
without tring the lokiwiz to unlock, i used shelltools to flash the wm6.0.
it was successful, it asked me to do a hard reset.
Since then i am stuck up with the boot screen.
I can't get my Mobile back working.
i tried flashing with the Offical rom but of no use.
i have tried button rom, love rom. nothing works out.
without much knowledge i upgrade my spl & IPL to 3.08
now i am not able to downgrade that too.
tried flashing different roms but of no use, still it stucks up in the boot screen.
the only hope iam having is i am able to get into the boot loader.
I am not sure, where to post this thread, my appologize if i have posted in the wrong page.
below is the information i have on the screen
IPL 2.26
SPL 3.08
GSM 01.12.10
OS 1.5.4.2
Some one please help me out. i am very much worried, any help is very much appreciated.Thanks a bunch in advance !
dosai.
Have you tried flashing from the bootloader to an official rom?
thanks for reverting, i have tried that too, but of no use.
Sounds to me like you didn't run the Cert_SPCS and EnableRapi cab files before flashing with ShellTool. Being stuck at the splash screen is a dead giveaway.
I never did understand why someone would attempt to flash a ROM without doing ALL the steps. . .
i did ran Cert_SPCS and EnableRapi cab before running the shelltool. shell tool took around 10 mins to complete the update.after restart, my phone stucked up in the boot screen!. (i remember not unlocking the cid before proceeding with the shelltool) .
is there any way to get the mobile working i am too worried.
Solution
Hi, press and hold the CamShot Button and press the Power button, when you see a multi-color screen you can make a update again.
Hello all Im new here and have the same problem. I followed all the steps and followed all the instructions to fix this problem but nothing. I am stuck on the multi-color screen and i can't do nothing! HELPPPPPPPPPPPP!

help o2 got stuck during rom update

hi! friends need an urgent help plz while i was updating the rom my o2 got stuck with some blank screen written with "SERIAL" on the top and "VS1.02" at the bottom plz help how to get back my phone software
simple steps first: Have you performed a manual soft reset? If so then please list everything you have done/tried so we are not reinventing the wheel in trying to help.

diamond is not responding (after spl)

please help as diamond is not responding(after installing spl)
--------------------------------------------------------------------------------
i installed some diamond spl on diamond although it completed 100 percent and turned off, and model id error flashed on screen, now it is not responding (not turning on) is there any solution to install any spl either stock or hard any so the device can turn on , plz help........any way to spl at this stage?

Categories

Resources