Hi,
I have a Qtek 2020 with WM6.1 (Athers Rom ) and after loosing my original headphone I've bought one from the net, wich I believe is from Qtek s200, it has two control boxes, one for volume and another one with a single button for anwsering calls. The problem is that the button doesn't work on my PPC. The volume works, the mic works, but the button doesn't do nothing.
Is there any kind of driver or software that alows me to give life to it?
Thanx
Related
Hi all,
I swapped my old O2 G2 BT headset for the new O2 one and have to say I noticed little improvement. I even upgraded to the 3900 build of the stack but no difference. However I then gotta thinking....
By default the profile being used was hands-free, but I seemed to remember the XDA2 using only headset. So - I found that by holding the -vol button for 15 secs I could register it as a headset profile (the XDA2s cannot use any of the hands-free bits anyway - voicedial etc etc).
Well, the audio quality is improved and the range appears to be better. It is still not perfect (or as good as it was on the XDA2) but it is now useable.
I am going to test for the week before I decide if I shall get a refund or not.
Cheers - Rich
Hi Rakh!
Where can I get the BT3900?
Thanks!
ftp://xda:[email protected] Upgrades/BroadcomCorp_BT1.0.0.3900.cab
Re: BT headset/handsfree profile - this might improve qualit
rakh1 said:
By default the profile being used was hands-free, but I seemed to remember the XDA2 using only headset. So - I found that by holding the -vol button for 15 secs I could register it as a headset profile (the XDA2s cannot use any of the hands-free bits anyway - voicedial etc etc).
Click to expand...
Click to collapse
the -vol button on the side?
When did you do that? - it doesn't seem to do anything on mine??
Thanks
--ian
Hi, yes the -vol button on the side. Switch it off (red light) wait 5 secs and then hold the -vol button for 15 (yes fifteen) seconds!
R
Hi,
Nope - still doesn't seem to do anything on mine. Either i'm doing something wrong or it only works on the xdaIIs and not the M2000 (they are suposed to be the same hardware but it might be a software thing).
Thanks anyway,
--ian
-vol button on the side of the O2 BT headset - not the XDA2s
Sorry for the confusion but I didn;t figure out what you were doing unitl now
Rich
Ahhhhh - doh!
Thanks for clearing that up.
I have a Jabra BT250 - and yes I was using the vol- on the phone
--ian
Jabra phones default to the headset program. Holding in the +Volume button on the headset while setting up for pairing turns on the optional Hands-free profile. This is just hte opposite of what the original post was about. The original poster had a G2 headset which defaults to Hands-free, but can be forced to Headset Profile.
Hi,
So what's the difference between headset and hands free?
--ian
Hands-free enables support for voice dialling etc etc etc. Headset simply allows you to use the mic and earpiece of the headset. I presume that the added functionality of the hands-free protocols take some of the 'bandwidth' from the voice part of the protocol and as a result exagerate the bad sound quality...???
R
Jabra headset
Hi to everyone!
I'm a Jabra user myself but I can't seem to enjoy the last number called redial feature with my XDA2 device (with ROM by Dr. Stein).
Any suggestions on how I can use this feature?
Thank you very much!
i have a motorola HS850.
it defaults to handsfree
anyone knows how to force it to headset?
it used to work such that when I open the boom on an incoming call, the call will automatically be answered.
now it doesnt work that way..
it just waits for either the bluetooth action button or the green answer button on xda iis to be pressed..
i have downgraded by BT [ recently upgraded to 3900 ] back to 3500 and the Motorola HS850 can auto answer whenever the boom is opened..
Guess 3900 is not perfect anymore
My HS850 works fine with BT 3900
Perfectly clear. Not tried switching handsfree to headset tho.
jabra bt 250
i m using a JAbra bt 250 and a qtek 9090..i tried the setting...but dont kno if it worked...in my shortcuts..it says hands-free connction to jabra..but i want it to be headset...coz thers too much of crackling right now..?
--------------------------------------------------------------------------------
Hi!
I have i mate JasJar, but there are some problems which are a bit annoying and I will ask you if you can help
Does anybody have problems using BT Jabra 500 working with Jasjar?
I cant hear any of my incoming/outgoing calls nor can I hear a ringing in BT.
Jasjar discover BT and pairing is OK ( just in case I did couple times -no luck)
when I use answer/end button on BT is dialing out but no sound on BT
on other side that I call they can hear my voice but I can't hear anything
Do I need any software to instal in jasjar ???
ROM version 1.13.53 WWE
ROM date 09\23\05
Radio version 1.03.01
Protocol version 42.36.P8
ExRom version 1.13.137 WWE
Please help me out
Thanx
I have BT 500 and have no problems, it sounds like the headset has a problem not the phone.
Also have my own and a client's Jabra 500 working successfully with o2 Xda Execs.
Stupid question I know, but you have tried increasing the volume on the headset buttons?
I did try everything , volume etc , contact jabra and try there sugestion
such as :
could be a pairing issue, or a bad speaker on the BT500. Please try a reset and re-pair of the phone and headset first:
Turn the headset off.
Plug the headset charging cord into a wall outlet.
Connect the headset to the charging cord for 5 seconds.
Disconnect the headset.
Remove the headset from the phone Bluetooth menu.
Turn the phone off.
Remove the battery (and sim card, if removable), and hold out for 5 seconds.
Re-install the battery (and sim card, if applicable) and turn the phone on, but do not touch any settings.
Turn the headset on.
Put the headset into pairing mode by pressing and holding the pairing button until you see a steady blue light. Release the button.
Perform the pairing procedure for the phone.
SIMPLY IS NOT WORKING
try with friend V3 razor and same thing
I also have the BT 500 + jasjar
It just works better than the BT 250 which was my past one.
To be honest, what I have on my jasjar is the new O2 rom upgrade (and that should not do any difference) I think there is something wrong with your jasjar
Maybe you will be forced to try the bad solution HARDREST try the headset with other phones before doing that
i beleive it's the headset that has the problem, since you tried it with another phone.
i have the bt500 with the imate jasjar and also the kjam and it's more than perfect for me, the sound is cristal clear on all the phones i tried on.
maybe you should replace it with a new one.
What I mean is not a factory mistake in the headset
I think the phoen is getting complex and some data have been lost (possible)
By the way, I haven't installed the BT headset fix, yet it works fine.
I think I read all of the VoiceCommand 1.6 & Bluetooth threads and tried any of the solutions (0.9f , manual regedit, BTVoiceCommand.exe ... )
But probably I missed something.
First question I could not find an answer for:
How is VoiceCommand supposed to be started after the fix:
a) Does it only work starting VoiceCommand with a Button on the Bluetooth device
b) Should it also work using a Button on the Hermes ?
If the answer is a): My Cars Device has a Button to start calls. If you do not dial a number, then this button redials the last called Number. Is this the right "command" that VoiceCommand listenes for to start ?
If not: Is there a possibility to change VoiceCommand to react to this "command" ?
Is there kind of a Bluetooth- Sniffer to find out, which commands are exchanged between the car and the phone to probably fix this ?
Am I totally wrong and all I need is another Version of WM6 ?
Can anyone help me ?
Thanx
Tode
P.S.: It did not work using the original WM5- OS from T-Mobile Germany, and (Radio 1.1x ) and it still does not work with Schaps WM6 3.30a in german, that I actually use (Radio 1.41.00.10)
Voice command can be activated from your hermes and indeed needs to be mapped to button five on the hermes which is the button on the left hand side below the ok button.
In all my many installations on the hermes it seems to map to button 1 (internet explorer) by default and needs to be changed in start>settings>personal>buttons.
My understanding - and I'm no expert - is that the button push on your bluetooth headset merely activates voice command. in order to do a 'redial' you need to activate VC and say 'redial'.
I would say VC overides the usual behaviour of headset and phone functions.
The 'button' you push on your car stereo would need to activate VC.
Never heard of such a sniffer but I assume that if it is set up correctly then the activation from the car stereo should replicate the button push from a headset and fire up VC.
Have you tried pairing a bluetooth headset first just to make sure VC and the fix has installed properly? It's very temperamental and I generally have to install it quite a few times before the combination of reg edits and power off/resets get it stable.
Oh and I forgot to say that if you have any evidence of Cyberon Voice Commander on the device it almost certainly wont work - seems to be a clash. I chose the cleanest rom I could find (LSVW) and had to remove all the voice commander cabs and fixes from the ext rom the hard reset. This seemed to work once I had added the reg edit to make sure the button was firing up BTVoiceCommand and not BTVCBasic.
found an old B-Speech Headset...
at the moment I am trying a Hard reset and Remove of all Cyberon- Registry Entries etc. Probably it will work with a "clean" new Install.
Thanx for your Tipps, I will tell if it worked.
Tode
ok... With my Bluetooth Headset I finally got it to work: I press the Button on the headset, and VoiceCommand starts correctly over the Headset.
BUT: The Button 5 still uses the Hermes' speaker / microphone.
AND: The button in my Car does NOT work the same: It does NOT start VoiceCommand but still recalls the last dialled Number.
So there are two possibilities for me to solve the Problem:
if I could make the Button 5 start Voicecommand over the Headset and NOT over the Handset, then my Problem would be solved. Does this work somehow ?
if I could make VoiceCommand react on the command comming from my Car, instead of redialling the last Number, then it would be ok as well.
Any suggestions ?
Thanx
Tode
Dear experts,
Sorry if this question was answered before, but I've been searching through the threads and couldn't find one..
I have a WM5 Orange Artemis (SPV M650) and I'm facing the following issue: when I play music with WMPlayer I get sound both through the phone speaker and the usb headphones. This is the same case with a friend of mine having the same device.
Probably there is some sort of a software solution to this problem, since with the already-installed FM radio application there is a button you can use to activate the speaker or to redirect sound through the headphones only.
Now I'm not able to use my phone as a music player due to this problem so any help will be much appreciated. Thank you!
Ksu
Had this problem before, open up the volume slider part of the earphones with a small screwdriver (push on the plastic tabs that hold the 2 sides together) and separate the wires going into and out of it, I found some were crossing and moving them apart sorted it fine!
Hope this helps...
Thanks for yr reply Pjtheman, I will try this, though I will keep wondering if it were a matter of crossed wiring, why it works fine with the radio application!!
I'll open the headphones slider and see what I can find..
yours, Ksu
I've just opened the headphones slider and found that all the wires were duly isolated from each other..
Perhaps a solution to this problem is to install advanced volume controls that can mute and control the volume of the earphones and the speaker independantly. Does such application exist??
Thanks for yr help.
Ksu
Guys,
Has anyone here experienced the same problem?? Am I the only one? Would you pls try and tell me if you have the same problem? Thanks for your help..
Ksu
Hi everyone,
I recently acquired this iphone headset, the mic and play/pause button are working correctly. However, the volumen buttons are not. I found this link https://forum.xda-developers.com/showpost.php?p=69138210&postcount=4, but I don't now how can I edit the system/usr/keylayout/Generic.kl file. I'm using lineage 14.1 and I have root access. Any help is appreciated.
This is a hardware issue not a software issue.
IPhone headphones are wired differently from Android headphone with volume buttons.
Remapping your system won't do anything.
I see... thanks for your reply, anyway. So if they are wired differently, dou you know if there is some kind of adapter to make this work? The headphones are good enough as they are, but still...