Hi all, I have a problem with my MDA Pro, my phone usually use WM6 OS but when I come back the T-Mobile WM5 Original ROM, the backlight button can not be used, click and nothing happen. I hope someone will help me to sovle this problem. Thanks a lot!
I think ,maybe you should change another ROM on you MDA PRO,this problem was happend in my Universal,at last,the only way is use another ROM.
By the way,you can try to:start->setting>button , to set you backlight button.
Good luck to you!
Mine's an spv m5000 (UK-Orange). When I got the phone (2nd hand) it had the problem you described, although I knew it worked as it would get me into bootloader mode. Strangely, flashing Ranju's 6.1 made it work again.
Thanks for everybody! I've had a solution to solve this problem, I downloaded a program: "Ivan Light Bulb 2" and after install it into my device, the backlight button works again. Great!
Related
Hi all, after upgrading from my Orange ROM to the UNI_Qtek_WWE_11364_151_10300_Ship ROM, my M5000 Universal shows only a blank screen and USB v1.00. I tried to hard-reset with and without pressing the on/off button at the same time. Hope somebody can help me. Thanks!!
Hi all, problem solved after applying the radio only rom again.
Hi Swisscom user...
Any idea where to find a link where to try TV Live with Swisscom :?:
Hello all,
i had a PDA Mypal Asus A696 with ROM WWE (English) v3.0702
i changed languaje to Spanish to upgrade to WM6. In the upgrading process appeared DOS screen with info about the upgraging. after "Write OS" and checked the PDA reboot and turn to black screen. After that, i cannot switch on the PDA. i have tried to perform a reboot, hard reset,... but always the same: Black Screen (as switch off).
Could someone help me please? i´m desperated.....
Best Regards to all.
Nobody can help me?
Any idea?
Please
Something colsed happened to me
Hola,
I sometimes had the problem that the screen light was at the minimum when on battery. The only way to solve the problem is to make a soft reset while your PDA is linked by USB to your computer. Then, it should show the splashscreen.
After upgrading, did you get a good reboot or not ?
If not, hum ! Might be very bad for you... Sorry
Please inform
Thanks for your info.
I think that the upgrade was no performed successfully. It´s appears that everything was Ok but after reboot, nothing happens.
USB to PC is dead. Charge is dead (only red led is switch on but never turn to green after several hours).
I think that my PDA is broken. My only solution is to contact with support to repair it (150€) :-(
If you have any idea more... please tell me.
Thanks and best regards.
Ok then......
PDA is going to Asus (for repair, of course) :-(
hey all,
i run into a problem today, my p3300 flashed with wm6 original from t-mobile netherlands keeps closing by itself. sometimes i see the screen dimming out and stay in a dark blue color, then i have to reset it to make it work,.
Sometimes it works for a bit longer then it shuts down again, and to power it on again i have to take off the battery.
I tryed hard-reset, no success. ima flash it again now and see if it helps.
If anyone knows a solution please
update: tryed reflashing with the same rom, didnt fix the problem. trying now with the english version (my own was dutch)
Did your problem start when you flashed a new rom? I had the same without doing nothing, Artemis was only 6 months old...I returned it back and they changed the mobo. Hope sincerely that this won't happen to you
hello, i had probably same problem:
http://forum.xda-developers.com/showthread.php?t=397924
Hi all,
I have a huge problem and I hope you guys can help me. I tried to flash the orbit (german) artemis of my brother. First flashed the uspl and everything worked fine. At the end there came this penguin picture and the screen stayed black/blue. Then I flashed the rom (MossisROMV3.0GER Windows Mobile 6.5).
HOWEVER: Right then the battery of the laptop went down and the pc switched off. Unfortunately we couldnt plug it in, since we didnt have the cable with us. Now after pluging in the pc there were some connection error notices. Since I didnt know how to proceed I removed the battery of the artemis. I thought I should repeat everything from the beginning on. However the phone always got stuck at the blue o2 screen showing the data:
IPL 3.04.0001
SPL 3.04.0000
GSM 02.88.90
OS 3.13.0.0
Softreset and harrest doesnt make any difference. The phone always gets stuck here.
Is the phone bricked?? Why then does it start? Please help me out asap, since the phone is needed. What can I do?
Thanks in advance
brm
first you are NOT CID unlocked (SPL 3.04.0000)
so you can only flash german orbit ROM on the phone to revive it
1. get to bootloader (press and hold the record button and reset the phone using stylus)
you will get the tri colour screen
2. connect the phone via USB to PC (no need to look for activesync/WMDC connection in this case)
3. and run the RUU (official O2 german ROM for O2 Xda Orbit)
BTW i have official o2 UK ROM in my 4shared account
look for the link in my signature
you may try your luck on that
Hi,
thanks for the fast respond. I read the just before some where else and right now I am searching for the original german rom. However cant find it anywere.
Do you think the english one will work too?
best,
brm
sheennick123456 said:
BTW i have official o2 UK ROM in my 4shared account
look for the link in my signature
you may try your luck on that
Click to expand...
Click to collapse
very few chances of that ....
but you can have a go atleast
i might be having an german official ROM not sure though
if i have it i will upload it ASAP
Hi,
thanks sheennick123456. Really kind for your fast responses, Finally I found the original german rom and right now i am flashing it. Afterwards i am gonna flash a new rom and hopefully everything will wirk fine. But thanks again for your kind help.
best,
brm
LOL even i got 1
uploading it now as i type....
it might help someone .....
which rom
Hi again,
after installing a wm 6.5 ger rom i must say i dont like it at all. can you recommend me another one? i think one with htc touchflo would be great, but which one is it?
If i want to flash a new rom, do i first have to flash the original rom before proceeding?
best,
brm
Hi everyone,
I've been trying to cook a WM6.5 in Portuguese (I used some files rom WM6.1PTG and I translated some others) with Visual Diamond Kitchen and in the cooking part all went well, I have the .ndh file generated and without errors.
Then I flash the Diamond and after the flashing is concluded the diamond makes itself a reboot and stops after the first boot screen with TouchDiamond and the red information about the versions.
I tried to do a hard restart, soft, remove and out again the batery without success.
Does anybody have the same problem?
I'll appreciate help.
Best Regards,
Armaia
Do you removed "FWUPDATE"?
pspeter said:
Do you removed "FWUPDATE"?
Click to expand...
Click to collapse
that FWUPDATE troubled me a lot!!!!
No, I didn't. Do you think that could be the problem? I,m going to try.
Thanks
Try to change the rom . Pull out the stylus , Press the reset button and hold the VOLUME DOWN and the right down button . After connect to pc
Hi,
I removed the FWDATE but the problem occurs in the same way.
AM
Armaia said:
Hi,
I removed the FWDATE but the problem occurs in the same way.
AM
Click to expand...
Click to collapse
Try to restore first your original shipped rom and then reflash your own rom.
Hi All,
I have the same problem, I flashed MightygroovyROM, after first boot, it stops, there is only "Touch Diamond" on the screen. I tried hard reset but doesnt work. Since activesync connection couldnt establish, I couldnt do anything.
Anyone know another technique to connect without activesync ? or is there any other way to go back old rom any flaeshing a new rom ?
Best regards
Kag
Armaia said:
Hi everyone,
I've been trying to cook a WM6.5 in Portuguese (I used some files rom WM6.1PTG and I translated some others) with Visual Diamond Kitchen and in the cooking part all went well, I have the .ndh file generated and without errors.
Then I flash the Diamond and after the flashing is concluded the diamond makes itself a reboot and stops after the first boot screen with TouchDiamond and the red information about the versions.
I tried to do a hard restart, soft, remove and out again the batery without success.
Does anybody have the same problem?
I'll appreciate help.
Best Regards,
Armaia
Click to expand...
Click to collapse