A696 Black Screen (it don´t switch on) - Upgrading, Modifying and Unlocking

Hello all,
i had a PDA Mypal Asus A696 with ROM WWE (English) v3.0702
i changed languaje to Spanish to upgrade to WM6. In the upgrading process appeared DOS screen with info about the upgraging. after "Write OS" and checked the PDA reboot and turn to black screen. After that, i cannot switch on the PDA. i have tried to perform a reboot, hard reset,... but always the same: Black Screen (as switch off).
Could someone help me please? i´m desperated.....
Best Regards to all.

Nobody can help me?
Any idea?
Please

Something colsed happened to me
Hola,
I sometimes had the problem that the screen light was at the minimum when on battery. The only way to solve the problem is to make a soft reset while your PDA is linked by USB to your computer. Then, it should show the splashscreen.
After upgrading, did you get a good reboot or not ?
If not, hum ! Might be very bad for you... Sorry
Please inform

Thanks for your info.
I think that the upgrade was no performed successfully. It´s appears that everything was Ok but after reboot, nothing happens.
USB to PC is dead. Charge is dead (only red led is switch on but never turn to green after several hours).
I think that my PDA is broken. My only solution is to contact with support to repair it (150€) :-(
If you have any idea more... please tell me.
Thanks and best regards.

Ok then......
PDA is going to Asus (for repair, of course) :-(

Related

help needed / auto restarting

hello!
Can anyone help me with this:
after 5 or 10 minutes, or even at the splash screen, my device automatically restarts and does it for several times.
When i try to put it into bootloader mode i see usb,..... but only for a minute. after that it goes out of bootloader mode and starts the OS again...
So i'm a bit worried that when i flash it, the bootloader mode will go out and the device will try to restart.
Any known sollutions to this problem? Any help would be appreciated!!
ps: no answers in the wiki nor in the forum.
thanks in advance to your replies!!!!!
I think your battery is given up or you have bad connection so that you dont get enough power.
Try first to clean the battery and device connections(best to use contact spray for PCB boards) if doesnt help then you need to have new battery
Thanks for your reply.
I just got it back 2 weeks ago and they installed a new board in it... i made them send it back and fix it (i blamed them)
they also putted french rom and AZERTY keyboard in it so they can fix that to (i had englis OS and Qwerty).
Thx for your post, i appreciate it!
Restarting Problem - PLEASE HELP!!!
Hi
I have an Orange SPV m5000 that I rely on for to carry my contact address book and send text messages (I know other phones would do it but I really like my Uni).
Recently mine has decided that it's going restart itself every few seconds. I have no idea why it's doing this, but the shop I bought it from are not helping me at all.
I've hard reset the device and that hasn't worked so if anyone has any ideas then please let me know, or if you know of anywhere I can send it to be repaired (I'm in the UK).
Thanks in advance
Nick

p3300 wm6 turns off by itself

hey all,
i run into a problem today, my p3300 flashed with wm6 original from t-mobile netherlands keeps closing by itself. sometimes i see the screen dimming out and stay in a dark blue color, then i have to reset it to make it work,.
Sometimes it works for a bit longer then it shuts down again, and to power it on again i have to take off the battery.
I tryed hard-reset, no success. ima flash it again now and see if it helps.
If anyone knows a solution please
update: tryed reflashing with the same rom, didnt fix the problem. trying now with the english version (my own was dutch)
Did your problem start when you flashed a new rom? I had the same without doing nothing, Artemis was only 6 months old...I returned it back and they changed the mobo. Hope sincerely that this won't happen to you
hello, i had probably same problem:
http://forum.xda-developers.com/showthread.php?t=397924

Diamond disconnects during HardSPL update

Hi!
I just got myself a Diamond and im trying to upgrade it. I've read the following tutorial: http://forum.xda-developers.com/showthread.php?t=416211 but the Upgrading to HardSPL doesnt work for me.
When RUU starts updating, the screen on my phonescreen turns black (as it should do) but at the same time it disconnects from the computer and the program. and the phone freezes and i have to take out the battery and reset it. I've tried to repeat it many times, i also changed the power settings and everything.
I have ROM version: 1.93.413.3 SVE and Radio: 1.00.25.05 and Iam trying to update to SwiftBL
Thank You
After your screen turns black, don't flash the SPL yet.
Wait a while till you pc detects the "new" device and installs drivers for it.
If you have still troubles, PM me and we can do it together ...
sum1 help me out plz
oryt mate
sorrry to bother u
erm im on vodafone wiv the vodafone rom thing and i tried puttin a different rom on but it does'nt move past 0%
so i tried that olinex thing and thats not helpd either
stil stays at 0%
any tips? let me knw please
thanks
I have the same problem as stated above..
Screen turns black..
Phone gets disconnected from pc..
Windows is found a new hardware device and is asking for a hardware install..
Hardware Install Fails and phone remains disconnected with a black screen..
WHAT TO DO NOW..?????
I'm afraid of disconnecting my phone, because of the chance ending up with a brick.
Can someone please help me out..???
It happened to me before. For me it was due to the advanced battery setting.
I resolved it by unchecking "turn off device if not used for.." on both battery and external power. Hope this helps.
Nope this does not help..
My phone goes black and dissconnects from the pc and does not reconnect..
Get a connection error from the hardspl update program and have to remove battery to restart phone
Doe anyone have an idea what i am doing wrong..???
I have the same problem. and i have tryed everything...almost:S
Thank you all!
Thank you all for the quick replys,
I've found a solution to my problem.
First of all i unchecked all the battery saving options, and then i went to Settings--> USB to PC--> and uncheck the "Enable advanced network functionality" box, after this the upgrade worked.
Hope this works for you guys 2
Peace
Not working for me here . Htc Diamond from H3G ITA .
I can't get past the black screen . Activesync disconnects and never connects again ... I tried the 2 settings changes proposed here ; I tried waiting almost 10 minutes on the black screen ....
Any other ITA H3G user with the same problem (maybe solved....) or any other user that got away with this huge problem ??
Have you tried pasting SSPL-Manual.exe into Diamond's Windows directory and executing it?
I put it in the root and executed it .... screen went black ... activesync lost connection ....................... after 20 minutes still black screen and nothing happened .
Fortunatly unplug battery and restart got me the pda back working
PS. If I enter the multicolor screen I see as SPL 1.37.0.0 and above it says DIAM100 ..... if any of this info could help to get me more help
don.sina said:
Thank you all for the quick replys,
I've found a solution to my problem.
First of all i unchecked all the battery saving options, and then i went to Settings--> USB to PC--> and uncheck the "Enable advanced network functionality" box, after this the upgrade worked.
Hope this works for you guys 2
Peace
Click to expand...
Click to collapse
Worked like a charm for me
Thanks
grebbo said:
I put it in the root and executed it .... screen went black ... activesync lost connection ....................... after 20 minutes still black screen and nothing happened .
Fortunatly unplug battery and restart got me the pda back working
PS. If I enter the multicolor screen I see as SPL 1.37.0.0 and above it says DIAM100 ..... if any of this info could help to get me more help
Click to expand...
Click to collapse
I believe that is what will happen. I used this method to install 1.40.
After you get the black screen just follow instructions from step 2 in here:
http://modmydiamond.info/index.php?option=com_content&task=view&id=22&Itemid=26
Ignore the activesync turning green part.
The small words in the red box is easy to miss out.
had a similar problem...upgrading to the latest version of .net CF did the trick for me....u might want to check that out (nothing to lose in having an updated version anyway)
Tnx a lot catpuke ... I tried to run the update anyway even with no sync with pc .... it stayed to 0% for a little bit and then jumped to 100% .... now in tricolor shows 1.30 Olinex !
Will move on and try to update radio now !
Tnx again for the help

Returning to Stock SPL (With a twist)

Hi there,
I'd like to return my Diamond (O2 XDA Diamond) to stock SPL (1.37) since my touchscreen is out of order and I'd like to send it to O2.
I already flashed the stock ROM and now want to flash the stock SPL.
I was following several tutorials on how to do this, but had no luck.
The problem, I think, is that I need to confirm something on my device before flashing (SSPL gives a warning in my understanding), but I can't since I'm stuck on the "Tap on Screen to start Windows mobile device" (is in German for me, but the first screen after Hardreset).
Any Hints on passing that screen via Registry or flashing Stock SPL without any confirmation is highly appreciated.
slow23 said:
Hi there,
I'd like to return my Diamond (O2 XDA Diamond) to stock SPL (1.37) since my touchscreen is out of order and I'd like to send it to O2.
I already flashed the stock ROM and now want to flash the stock SPL.
I was following several tutorials on how to do this, but had no luck.
The problem, I think, is that I need to confirm something on my device before flashing (SSPL gives a warning in my understanding), but I can't since I'm stuck on the "Tap on Screen to start Windows mobile device" (is in German for me, but the first screen after Hardreset).
Any Hints on passing that screen via Registry or flashing Stock SPL without any confirmation is highly appreciated.
Click to expand...
Click to collapse
You can do thAT, on this way
Plug the USB cable to connect your Diamond with PC, make sure ActiveSync connected.
Copy "SSPL-Manual.exe" to Internal Storage on your Diamond.
On your Diamond, execute "SSPL-Manual.exe" and confirm to trust the excutable. Your Diamond screen will turn "BLACK" and ActiveSync will disconnect. *This is normal behavior***
Execute the ROMUpdateUtility.exe.
Your Diamond will automatically restart when finished.
To make sure stock SPL has been flashed back, press and hold "Vol-" key and use stylus to press reset once. until you see the tricolor screen and if you can see version of spl which before you flashed, it's ok!
Greetz
sucro said:
On your Diamond, execute "SSPL-Manual.exe" and confirm to trust the excutable.
Click to expand...
Click to collapse
Thank you sucro, but exactly that is my problem, since my screen is dead I can't confirm anything...
when i want to install the original htc rom after received the upgrade present to 100 this error message appear .for this aim i need to downgrade my spl to stock. . is there any manual or howto link and also original spl files please link it. i have been searching for a while.
my stock spl was 1.93.
any help would be appreciated.
masa1977 said:
is there any manual or howto link and also original spl files please link it.
Click to expand...
Click to collapse
It's in the HardSPL Developer Edition Thread.
thanks a lot slow23
slow23 said:
Thank you sucro, but exactly that is my problem, since my screen is dead I can't confirm anything...
Click to expand...
Click to collapse
You are welcome, try this, i discover this combination of buttons
ENTER+VOL UP = ALIGN SCREEN
that means, with this combinations of buttons, you can directly enter ALIGN SCREEN options, and try to align screen , sometimes this helped me, cause my touch screen has same problem, it start to freeze randomly, i don't know why, sometimes in right, sometimes in left corner, up-down, randomly, i noticed that htc diamond when is exposed , when i'm out and it's sunny weather, it stop to responding on touch, one my friend specialist for mobiles, tell me, maybe this happen, cause bellow screen in some pda is some thin rubber, and from heat it start to expand, and that cause problems, maybe this situation is in htc diamond...
greetz and good luck
Returning to Stock SPL
slow23 said:
Hi there,
I'd like to return my Diamond (O2 XDA Diamond) to stock SPL (1.37) since my touchscreen is out of order and I'd like to send it to O2.
I already flashed the stock ROM and now want to flash the stock SPL.
I was following several tutorials on how to do this, but had no luck.
The problem, I think, is that I need to confirm something on my device before flashing (SSPL gives a warning in my understanding), but I can't since I'm stuck on the "Tap on Screen to start Windows mobile device" (is in German for me, but the first screen after Hardreset).
Any Hints on passing that screen via Registry or flashing Stock SPL without any confirmation is highly appreciated.
Click to expand...
Click to collapse
Hi
I have similar problem and I will tell you what I did to get back to Stock SPL.
1. Flash the BSBs latest ROM from this thread, http://forum.xda-developers.com/showthread.php?t=506533 . Either by RUU or moving the diaming.nbh to the storage, this ROM does not require allignment or any other input.
2. Install My Mobiler from http://mymobiler.com in your computer, where you can see your mobile screen in your computer and operate using your mouse.
3. Then return to the stock SPL as given in this thread http://forum.xda-developers.com/showpost.php?p=2324829&postcount=39.
4. Flash your ROM again from the HTC. This can be done once the system connects to the phone.
I am successful in doing the above.
Regards,
V.Balaji

help

hi i am from italy my i-mate jasjam when i try to updgrade the rom stop and told me that the device is not responding help
please help me fast
hi
well you must to tell us more than that....
If it is stucked at some % you never but never make a hard reset...
do you make the HSPL?
the rom i have is 6.5_test by fcw it never start % when i updgrade and thank you for fast reply
+ Que PPC said:
well you must to tell us more than that....
If it is stucked at some % you never but never make a hard reset...
do you make the HSPL?
Click to expand...
Click to collapse
as que said you need to tell us more about your problem there isnt any help i can offer with so little information
it stucks on tricolor screen?
or stucks on a % bar, white screen?
Do you perform the Hardspl? first?
or just saw the rom and say, i will upgrade...!
i had also this problemes and i solved it by change the usb port. you can also change the usb cabel
remember!!!
never do a hardreset on this kind of troubles ok?
its better to drop off the battery instead of softreset
Does this guy bricks his phone?
Hahaha i dont think so but he didnt answer... so i think he just softreset his phone... everything boots again... and tadaaaaa! well i hope so...
i change the usb port and the usb cabel but nothing

Categories

Resources