hello!
Can anyone help me with this:
after 5 or 10 minutes, or even at the splash screen, my device automatically restarts and does it for several times.
When i try to put it into bootloader mode i see usb,..... but only for a minute. after that it goes out of bootloader mode and starts the OS again...
So i'm a bit worried that when i flash it, the bootloader mode will go out and the device will try to restart.
Any known sollutions to this problem? Any help would be appreciated!!
ps: no answers in the wiki nor in the forum.
thanks in advance to your replies!!!!!
I think your battery is given up or you have bad connection so that you dont get enough power.
Try first to clean the battery and device connections(best to use contact spray for PCB boards) if doesnt help then you need to have new battery
Thanks for your reply.
I just got it back 2 weeks ago and they installed a new board in it... i made them send it back and fix it (i blamed them)
they also putted french rom and AZERTY keyboard in it so they can fix that to (i had englis OS and Qwerty).
Thx for your post, i appreciate it!
Restarting Problem - PLEASE HELP!!!
Hi
I have an Orange SPV m5000 that I rely on for to carry my contact address book and send text messages (I know other phones would do it but I really like my Uni).
Recently mine has decided that it's going restart itself every few seconds. I have no idea why it's doing this, but the shop I bought it from are not helping me at all.
I've hard reset the device and that hasn't worked so if anyone has any ideas then please let me know, or if you know of anywhere I can send it to be repaired (I'm in the UK).
Thanks in advance
Nick
Related
First, I would like to thank everyone on this forum for valuable information. I have been able to flash a Blue Angel and more recently a Universal (SPV M5000) with a Jasjar, O2 and Qtek ROM.
I have researched the forum but have not found any answer close to my problem.
After the lastest update (O2 Exec just released), I did not reset the unit properly and now my screen is completely dead/blank. I tried to reflash but it is no longer recognized (will not power back up)
No possibility in putting in Boot loader mode (power+light+reset) or doing a hard reset (the 2 _ and reset).
has anyone experienced this and can I revive it, at least, bring it back to a boot loader so I can reflash? Thank you to all :roll:
Just a thought. Have you tried leaving out the battery pack for a while, say an hour or better overnight? Might be worth trying the hard-reset sequence with the battery still out, then insert the battery and hard-reset again. If it responds, try flashing again.
It is possible to get the Universal in a totally confused state. Mine does this everytime if I power down the workstation *without* first disconnecting the Exec from the USB-Sync cable. Fortunately, it will respond after a battery out plus reset, then battery in plus soft-reset, so I don't actually have to clear the memory.
Hope you dig yourself out of the brown stuff!
i am trying this at the moment as I do not know what else to do. I will put the battery back tomorrow in hope it will restart again.
Thank you for the advice
i am trying this at the moment as I do not know what else to do. I will put the battery back tomorrow in hope it will restart again.
Thank you for the advice
claudef said:
i am trying this at the moment as I do not know what else to do. I will put the battery back tomorrow in hope it will restart again.
Thank you for the advice
Click to expand...
Click to collapse
No to do that , connect ypur ppc to pc amd flush again after finish just push reset buttom , you will be ok, otherwide try one more time
Unfortunately, I cannot flash because it will not power up or start the boot loader. The pc does not recognize the device
claudef said:
i am trying this at the moment as I do not know what else to do. I will put the battery back tomorrow in hope it will restart again.
Click to expand...
Click to collapse
That worked for my when I was flashing my JAM, no problems. Scary, but successful. Think I may have left it a couple of days, to be sure. I then reflashed it successfully.
Although I refused to flash my Exec - too damned expensive to replace, and the ROM is 95% as good as it needs to be.
Hi,
i've been searching this forum all day now, and i haven't found a post for my problem. I've been using schap's rom for a few weeks now and yesterday, when i got in my car and put my hermes (t-mobile vario II) into the charger it resetted and it didn't boot anymore. the dark screen comes up (the one with the red numbers) and it goes into the next screen but thats it. I even left it that way for an hour but still no working phone...
Can anybody please help me out? i'd hate it to go back to my old nokia...
HELP!
thanks in advance
Have you tried a hard reset? Also, my phone got stuck there once, and hitting the little reset button on the bottom of the phone got it to work.
I did try a hard reset several times.. still the same problem...
please refer to the unbricking thread here: http://forum.xda-developers.com/showthread.php?t=286755
You will find all the info you need in that thread.
Fixed it!
Hi!
Well i did fix it all right! (happy happy joy joy)
I don't know what went wrong, but i made myself a nice new rom with pandorras kitchen (hermes style) which i installed via the SD card using this info: http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
Thanks for that!
you could also fix that problem by installing Hardspl7 , it happened with me twice i don't remember with what rom , but it happened and fixed using HardSPL7 .
WBR
Hi all experts,
I am a newbie on this. I am in Canada, since here we dont have i780, so I brought it on ebay and didn't realize its not really an unlock phone.(been cheated) although is sim free but GPS and many other 3rd party app don't work. so i was looking for solutions and found your thread here.
I followed the flashing guide and everything seems to be ok until the russians rom is flashed. The phone turned off itself and cannot turn on anymore. I have tried holding ENTER and FUNCTION button, solf reset hole, and Start + End buttons to turn it on but it doesn't response at all.
I have spent my hard earned $500 on this phone and i am so depressed now... Please kindly help me on fixing my "not just bricked, but dead phone" or i have to save up for months for a new one... sigh..
your response is highly appreciated
Jack
I feel your pain and I had the same issue as you before.
Phone won't turn on after flashing and the mirage reported the flash was 100% done.
I suspect this is due to the samsung modem driver was not installed properly. I had forgotten to do a reboot after the driver install or it might be due to something else.
The way I fixed it was to send to ther service center as it is still under warranty. They had to replace some chips to make it work again and I think that might be your last hope.
thanks for your advise. I did install the samsung modem driver and did reboot the PC before starting mirage updater..... but somehow turn that way.
I brought it from ebay, do you think it can still be warranty? anyways.. gotta try my luck.
thanks tho
I just contacted Canada's samsung service centre. They said They dont have this model here in Canada, so cannot fix my phone.
Please, anyone can give me a hand?
What about a hard reset? have you try it?
try to re load the rom.. i am using HH1 for phone and HH5 for the PDA... works good... with the russian ROM PU (if i am not wrong) i had to load few times as the process stopped at 80% or so... and u can load the ROM from this thread without loading the PU rom..
i have the same troubled too~~
Hi all,
I have a hp 6815 and i am desperate to fix it.
I had upgraded ROM a few times with sd card fine, then i went to change the rom again and i think i didn't wait long enough and messed up the booting. But problem now is it won't go into to boot loader mode at all, it is totally black with no power.
It has an orange light when charging, so i think the battery is ok.
But i am sure the boot loader is corrupted and it needs restoring with jtag.
I have connected it up with some make shift wires and entered the jflashmm what i have heard other people fix their dead boots. It would ask me first question what i answer then it goes to next question. What is binfile name, i think ! I put in the EBO etc and have tried various ways but it won't register any. I just need help with the commands. I have already copy and renamed file for EBO_a.nb0. I just need a little help, if i fix this with help i swear i will send the person who helps at least 20 uk pounds through paypal, I would be overjoyed !!
So someone with good jtag knowledge and ipaqs would be great.
Also another thing is i'm not sure what the ntrst connection is to on jtag. Is it connected to anything at all ? As the diagram on dead boots shows this but not seeming connected, am i right ?
Thankyou in advance
Please someone give a little help.
Hello,
Please someone help with this. Just need to know about jtag[ntrst] and all the commands i need to input to fix boatloader from the 1st to last.
If i get this info and fix it i will either pay some money or give my TUROK game to you what is boxed with key and manual ready for multiplayer action, atm i'm into gta4 so don't play turok anymore. But this is a solid unreal engine 3 game.
FRAGEYE said:
give my TUROK game to you
Click to expand...
Click to collapse
SWEET!!!!
I guess ill try to help you,
Im going to ask you to try to "hard reset" your device...
I already googled it, and i found this Youtube Video
Tell me if that does anything....
If you still need assistance, then Private message me.
Thankyou, believe me though i have tried everything, no power only when charging. I have to fix this with jtag. Really all i need is commands from 1st to last.
Whoever can help with the right commands gets a game. Remember it is a ipaq 6815.
Does anyone know anyone with the knowledge.
I had before upgraded rom a few times with no worries and bricked it before but not where it has no boatloader.
I am pretty handy with flashing but need help with this.
Please people help a kind soul.
Thankyou
Someone must know about jtag.
Hi all,
Wonder if anyone could give me a hand. My messaging function went into white screen, cant type or send message out.
I did a reboot a while ago because the phone froze on the wm screen. It chucked my spl back to 1.37. Wonder if anyone could give me a hand to let me know how to deal with this problem?
Do i need to hardflash my spl first?
Thanks.
tchiuhangng said:
Hi all,
Wonder if anyone could give me a hand. My messaging function went into white screen, cant type or send message out.
I did a reboot a while ago because the phone froze on the wm screen. It chucked my spl back to 1.37. Wonder if anyone could give me a hand to let me know how to deal with this problem?
Do i need to hardflash my spl first?
Thanks.
Click to expand...
Click to collapse
.
could you be a bit more specific? have you tried soft-resetting the device since it had this problem? if so you may need to hard-reset the device
not sure why, i tried hitting down vol + reset for a soft reset.
Went into the bootloader, but froze. Only said serial.
I am wondering do i need to hard flash the device first -.-"
Would be great if i get some help from someone.
Thanks!