Hi all!
Manual for recovery bricked FLAME
Symptoms: the device didn't switch on after experiments with an upgrade. Reacted only to power unit connection at the inserted battery - the orange led lights up. At this situation to bring the device back to life, only a flash bootloader (eboot.nb0) by means of interface JTAG is needed and possible.
1. Hardware preparation.
Please disassemble the FLAME and extract board. The detailed instruction
You should make a simple JTAG - cable.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Max lenght this cable is 20-25sm. My variant:
Alsoit is posible to produce some contacts, for example (see foto)
2. Software preparation.
To be required in addition:
1. Micro-SD card and cardreader.
2. Program SDFormatter, download here or here
3. FlameRecoveryTools from Medush, download
4. Diskimage.nb0 - any for FLAME. I extract it from official update
Well, now at all of us it is ready. We begin...
1. Extract FlameRecoveryTools on c:\
2. Run c:\FlameRecoveryTools\giveio_setup.exe (It driver for JTAG-cable). Please make sure that driver is installed and started.
3. Attach JTAG-cable to LPT-port your PC and FLAME board.
4. Plug power cable to FLAME board (or USB-cable from PC).
IMPORTANT! Do not press the button-indicator of the inserted accumulator!!!!
5. Open cmd-window. (Start-Run-cmd)
6. Go to c:\FlameRecoveryTools\JFlash_MM\
7. Run Start.bat
If everything is OK, a flash process will start and you should see:
If you see:
Please carefully check up correctness and reliability of all connections, a cause of error may be ONLY in it. Don't try to find missing file or any other program mistakes.
Ok, flash process is finished, verification successful, eboot.nbo has been flashed.
Unplug all, assemble your FLAME, plug AC-cable and turn on power.
Device is starting with error ERR-003A. (FOTO)
If you see message "battery is too low" - please wait for some time...and press reset again ))))
Ok.
8. Put micro-SD card in to your cardreader and run SDFormatter. Select "Full format".
9. Copy the following files to card: diskimage.nb0, eboot.nb0 (for example from my FlameRecoveryTools) end empty files-passwords rerr003a.kez and 1xdtgklo.kez.
10. Put card into device and start upgrade (press and hold soft-buttons (- and -) and press reset.
11. Finish!.
Insert the accumulator into place and turn on FLAME.
Enjoy the working device!
If my article has helped you, you can donate me:
WebMoney WMID 205584530674
WebMoney USD - Z177840443105
WebMoney Euro - E685734257524
PayPal: use recipient name "[email protected]"
I'm sorry for my bad English...
hello and thank you for this procedure. do you think, that is a possibility to create a JTAG for HP 2790b device? I have damaged bootloader (flash process did not well) and device is brick. I flashed it a lot of time, but now it is really dead. thanx for any info.
sinmae said:
hello and thank you for this procedure. do you think, that is a possibility to create a JTAG for HP 2790b device? I have damaged bootloader (flash process did not well) and device is brick. I flashed it a lot of time, but now it is really dead. thanx for any info.
Click to expand...
Click to collapse
Throught JTAG you can recovery any device. If you don't find scheme of contacts JTAG for your device in the Internet, you will have to make everything by yourself. HP has very individual scheme of contacts JTAG. That is why there is the only way - to bring your device (or you can by the same one but spoiled) to a good service center to unsold processor, find contacts JTAG and sold processor back. of cource they should do it with the guaranty of device safety.
Further is easier -knowing the contacts, you can sold contacts for JTAG and flash the device. I can help you with software. Wright a private message, I'll give you my e-mail.
Good Luck and never give up!
Help me i need JTAG for O2 Stealth
thanks Yudgin for your flame recovery manual !
could you please tell me how you could extract the bootloader for flame from the upgrade utility provided by O2
also i have a dead stealth --> could you share your insight as to what might the JTAG pin structure for this model
i have highlighted my thoughts in red --> i think these are active pins
oki, so I must lift the procesor. I have proper tools for that but not enough time for that. I report back when I found it, I guess there is more users who need JTAG for 27xx series. bye.
Yudgin said:
to bring your device (or you can by the same one but spoiled) to a good service center to unsold processor, find contacts JTAG and sold processor back.
Click to expand...
Click to collapse
Does anyone have the Flame JTAG Pin identification on the mainboard?
nuttapung said:
Help me i need JTAG for O2 Stealth
Click to expand...
Click to collapse
@nuttapung, have you find JTAG for your Stealth? I think I just had mine bricked as well. Days after kept it off unused, I turned it on, M2D intiated but then suddenly it automatically did a hard reset by itself. Upon completion, it started that hard reset process again and again so I have to unplug the battery. And that was the end of it.
heeelpmeeee pleaseeeee
have you find JTAG for your Stealth? please send me an copy of this...please... and the eboot.nb0...thx my email is [email protected]
important:
Hi my friend, I want to know where is the second TCK pin in flame board? I destory the TCK which pointed by your photo!
Mine too. I destroyed the TDI contacts. Anyone has the alternate contact point?
I done all after eboot my Flame sticks with ERR-003A
Yudgin said:
Hi all!
I done all after eboot my Flame sticks with ERR-003A and does'nt start rom uploading
and again goes into the same Err-003a screen, I tried many diffrent SD cards and Various Files eg. Eboot, eboot Diskimage .diskimage rerr03 etc nothing works. after pressing _ and _ and reset the flame goes off and after a second againg it shows ERR-003A screen, Any suggestion please?
Thank you
Click to expand...
Click to collapse
Related
Somebody please help me, i was trying to upgrade my hx2110 from WM2003SE to WM6,yeah it was my fault..i didn't follow the instruction very well... i was stupid, upgrading using SP29xxxx(2003 Update ROM from HP) then swap the NBF Files...upgrade complete, and now He's dead.. Pre-BL still works, but i have no luck to reflash, HPRUU flashing stop at 0.1% and it says "Congratulation...blaa..blaa" but nothing happened to my hx2110..i used to read the step to unbrick hx2110, but i don't have another iPAQ hx2000 series to do the trick..is there any other way to un-brick my iPAQ ? please help...sorry for my bad english...
well, you are sure that you are setting it into pre-bl the way you are supposed to? (it will say USB in the bottom left corner, not usb is connected) and you have deleted the whole ipaq folder off of your hard drive and (C:/ipaq) and run that service pack again right?
Your english is fine, let's try to get your device online again.
Yes, i pressed Calendar button to activate USB Mode, not USB Connected..but, still it doesn't fix the problem..
Your english is fine, let's try to get your device online again happy to hear that, thanks contradude...
sorry for being afk right now but I'm out and about (im posting this from my treo). you should take a look at the chrismrulz bootloader. its supposed to help when nothing else can. I'm surprised that the pre-bl isn't helping you fix you problem.
edit: i'll take a look tonight and see what I can do about helping you get your device up. if anyone else has any ideas, feel free to post
edit 2: I took a look around for ideas and the only one that still seems viable is grabbing another ipaq (either borrowing one from a friend or paying $10-40 on ebay and getting one you can hold onto for parts). good luck with your pda and next time don't let your excitement get in the way of methodically reading and executing the instructions. I would offer to lend my 2495 but I'm in orlando, florida usa
Wow...that's so far, shipping cost maybe will be equal to used iPAQ here...hehehe.. Thank's for your offer contradude...i really appreciate that..
Well, now i would like to show some screenshot :
Flash using SP29865 from HP :
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
It doen't detect Model ID and ROM but, this HPRUU allow me to flash...
The Process stops at 0.1% but, the flasher lies to me it said "Congratulation..bla..bla..bla"
and this is what happened if i'm using another ROM files such as SP33303,4PDA.RU ROM,and the others...
Wrong Language, Not Connected to ActiveSync,etc.
hmm...trying to borrow another hx2000 series, but who? almost everyone in my country using PDAPhone, rarely uses PDAOnly..any plan to sell it Mr.Contra? or maybe you'll send it to me as a birthday present ? hehehe... just kidding...This is the first time i'm using Windows Mobile Based PDA's very love it..but i killed it...
Too Much love will kill you...
oxzoned said:
Somebody please help me, i was trying to upgrade my hx2110 from WM2003SE to WM6,yeah it was my fault..i didn't follow the instruction very well... i was stupid, upgrading using SP29xxxx(2003 Update ROM from HP) then swap the NBF Files...upgrade complete, and now He's dead.. Pre-BL still works, but i have no luck to reflash, HPRUU flashing stop at 0.1% and it says "Congratulation...blaa..blaa" but nothing happened to my hx2110..i used to read the step to unbrick hx2110, but i don't have another iPAQ hx2000 series to do the trick..is there any other way to un-brick my iPAQ ? please help...sorry for my bad english...
Click to expand...
Click to collapse
See if the info. in the following links are helpful
http://forum.xda-developers.com/showthread.php?t=372799
Thanks hkksl..One more question, is it possible to Flash dead iPAQ using mtty / putty ? or maybe from SD/CF Cards ?if it possible, how? is there any tutorial links ? thanks in advance..
Edit :
Last nite i dream my device running WM6..Unfortunately, i was just a dream
is it possible to use this (HTC Wizard) tutorial to flash using mtty ?
http://forum.xda-developers.com/showthread.php?t=276963
i always run all of my updates from 'white screen bootloader' aka pre-bl. hmm... that's a very interesting screenshot. is it charging the battery still when you plug it into the dock... also make sure that after it says pre-bl and you put it in the cradle that you hit the calendar button so that it goes from usb is connected to usb. also, do you have a power adapter hooked up to your dock or are you trying to do it just over USB?
as far as trying mtty, if you want to try it in a really easy form try chrismrulz' bootloader. here is the download link for it. it prepares your rom and then uses mtty to upload to your device. make sure to turn off activesync on your computer (right click on the greyed-out icon and go to options and deactivate almost all of them). then you take that, plus your original firmware rom and put it on a folder on your hard drive with no spaces in the path (i put mine in C:/bootloader). you then run bootloader.exe and just let it do it's thing. I don't click on any of the pop-ups, other than to show it where the rom is. I hope this works for you
Thank's for the reply contradude, first of all i would like flash mine with SP29795.exe (the old ROM 2003SE) if it doesn't work..then i'll try Chris Bootloader ( even tries many times but nothing happened,maybe i didn't follow the instruction well )
I'll report soon, wheter it works or not...right now, i'm not confident with my english
WOOOOHOOOOOO!!!! I've made it, now my hx2110 running WM6 4PDA Version!!! Here's the step :
1.) Download SP29795.EXE from :
Code:
ftp://ftp.compaq.com/pub/softpaq/sp29501-30000/SP29795.exe
2.) Flash it using SP2975 RUU, it will flash your bricked iPAQ into WM2003SE 1.00.14
3.) Oops, flash completed..but some error has been occured..it won't enter WM2003SE
4.) Don't panic, reflash your iPAQ using SP29795 RUU, but swap the NBF From SP29865.exe
Code:
ftp://ftp.compaq.com/pub/softpaq/sp29501-30000/SP29865.exe
5.) Start flashing, after finished..voila! WM2003SE 1.10.09 should works..
6.) Now, flash your iPAQ to 1.00.00L then 1.00.00H after that go to WM6... ( see copenhagen tutorial from http://forum.xda-developers.com/showpost.php?p=1516882&postcount=66 )
7.Finished
I Would like to say thanks to Contradude, hkksl, copenhagen, Yurrix, and to everyone who made this possible.... THANKS!!!
Hello,
Need your guys help urgently. I have a HTC Excalibur, but recently did not power ON for about afew weeks, and now when I power ON, it will just hang at the booting green page showing "Windows Mobile Direct Push Technology", and can never goto the main screen at all, suspected that the software corrupted.
Please help, I have tried to use the Activesync but it does not detect my HTC Excalibur. Is there any way to reload back the default software/firmware image back to the device? like BlackBerry device, there's a software application and can use the Desktop Manager Application Loader to reload the software/firmware back to the device, is there such similar way for HTC Excalibur? Or any alternatives to resolve this issue?
Please HELP, any kind soul expert out there to help?
Thousand of thanks.
How to do a hard-reset. Won't reload to default but worth a try.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
hello there! Mine is the dopod c720w, do the steps for hard reset work for c720w? Merci
mosescso said:
hello there! Mine is the dopod c720w, do the steps for hard reset work for c720w? Merci
Click to expand...
Click to collapse
Yes it's the same phone
Just a different brand name.
hello there! Have tried several times, but it does not work, still the same as the problem, hang and stop at bootup screen. : (
What other ways?
mosescso said:
hello there! Have tried several times, but it does not work, still the same as the problem, hang and stop at bootup screen. : (
What other ways?
Click to expand...
Click to collapse
Sorry to ask a silly question did you see the onscreen promps to reset device?
Take out the sd card?
gospeed.racer said:
Take out the sd card?
Click to expand...
Click to collapse
Good answer gospeed
If only they put that in the pic.
You Want The BooTLoader Screen First {Color Screen}
mosescso said:
Hello,
Need your guys help urgently. I have a HTC Excalibur, but recently did not power ON for about afew weeks, and now when I power ON, it will just hang at the booting green page showing "Windows Mobile Direct Push Technology", and can never goto the main screen at all, suspected that the software corrupted.
Please help, I have tried to use the Activesync but it does not detect my HTC Excalibur. Is there any way to reload back the default software/firmware image back to the device? like BlackBerry device, there's a software application and can use the Desktop Manager Application Loader to reload the software/firmware back to the device, is there such similar way for HTC Excalibur? Or any alternatives to resolve this issue?
Please HELP, any kind soul expert out there to help?
Thousand of thanks.
Click to expand...
Click to collapse
They are 2 ways that You can get the bootloader screen back, by connecting your phone to your PC via USB, catch this {although the phone may look like it's not connected to your PC via active, but it is connected, you will not see the green Active sync icon on your PC at this time, but you phone is still connected to your PC via active sync}, understand this...!
Next, while your phone is connected to your PC via active sync, push and hold the camera button for several seconds, keep trying until the color screen appear {BootLoader screen}, should the BootLoader screen appear, You will have to install a 6.0 ROM back in your device, before you put a 6.1 ROM on your device.
If the above method should fail, this is another method, but kind of difficult, soft reset your mobile device, while your phone is coming back up, press and hold down the the 2 soft key {Home Key and Back Key} and the camera buttons at the same time, until the color screen comes up, you may have to try this several times, be patient. Should the color screen come up, install a 6.0 ROM back on your device before installing a 6.1 ROM to your device. These 2 method have worked for me and others in the past......!
Hi. İ have a O2 Xda Exec (Universal). I have changed the rom from there ; http://forum.xda-developers.com/showpost.php?p=1704506&postcount=1
everything is ok but at the align screen i stuck up. i'm tapping the target but it's starting over and over at beggining. Please help me.
no_war said:
Hi. İ have a O2 Xda Exec (Universal). I have changed the rom from there ; http://forum.xda-developers.com/showpost.php?p=1704506&postcount=1
everything is ok but at the align screen i stuck up. i'm tapping the target but it's starting over and over at beggining. Please help me.
Click to expand...
Click to collapse
Hi fellas i really need to help. Coz i'm stuck at the align screen. Help me!!!
no_war said:
Hi fellas i really need to help. Coz i'm stuck at the align screen. Help me!!!
Click to expand...
Click to collapse
This happened to me a long time ago and solved it by changing the ROM and then going back to the one I wanted
Hope it helps,
I fixed it by reseting into bootloader, then hard resetting, then re-aligned 4 or 5 times and it finally worked.
i tried everything. i changed the rom then i restarted it. i do hard reset but anything can not solved problem. wich rom have you tried?
i'm trying the mtty but i'm taking an error. You can see it at the picture. please help help helppp!!!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
connect your htc to pc when align screen appears. then, using pc explorer delete folowing file on htc: \Windows\welcome.exe
this can solve your problem.
go back to previous rom.
or change to another one... maybe there was some incompatibilty with that one
jesuis said:
go back to previous rom.
or change to another one... maybe there was some incompatibilty with that one
Click to expand...
Click to collapse
i did it. i tried the old rom but it is still not working.
Otets_vash said:
connect your htc to pc when align screen appears. then, using pc explorer delete folowing file on htc: \Windows\welcome.exe
this can solve your problem.
Click to expand...
Click to collapse
i can't delete the welcome.exe becouse it is read only. How can i do?
ок man. I will try to help you. there are two ways: simple (the 1st and crazy - the 2nd). So..
1st:
simply delete this shortcut (file) Welcome.lnk from this folder on HTC: \Windows\StartUp
note: after the 1st successful startup system will delete it independently, so you just skiping this step
2nd:
if You like to overcome difficulties like Armenian Komsomol member this way is for You!
Install on the personal computer the program pocket controller (like so is called), then connect PC to HTC for let pocket controller donloads cab file to HTC and then reboot HTC. The personal computer hooks control and already from the personal computer you can pass wellcome.ехе procedure and delete it using total commander if it present in your ROM.
good luck
Otets_vash said:
ок man. I will try to help you. there are two ways: simple (the 1st and crazy - the 2nd). So..
1st:
simply delete this shortcut (file) Welcome.lnk from this folder on HTC: \Windows\StartUp
note: after the 1st successful startup system will delete it independently, so you just skiping this step
2nd:
if You like to overcome difficulties like Armenian Komsomol member this way is for You!
Install on the personal computer the program pocket controller (like so is called), then connect PC to HTC for let pocket controller donloads cab file to HTC and then reboot HTC. The personal computer hooks control and already from the personal computer you can pass wellcome.ехе procedure and delete it using total commander if it present in your ROM.
good luck
Click to expand...
Click to collapse
Thanks for trying to help me but i'm stuck at the roms setup beggining align screen! Becouse of that i can't install soti pocket controller. and i can't find how to delete welcome file becouse it is read only still!
hmm..
you try to delete wellcome.lnk from Windows\StartUp or wellcome.exe from Widows ?
Otets_vash said:
hmm..
you try to delete wellcome.lnk from Windows\StartUp or wellcome.exe from Widows ?
Click to expand...
Click to collapse
Yes i tried but i can't do it. Becouse the file is read only the device don't give me the permission for deleting it! Help help help! How can i delete it ?
what do you mean saying "can't install soti pocket controller" ?
I think for the Pocket Controller to work it needs to be installed on both, your PC and the device. Could be mistaken, it's been a while since I used it last.
I'd re-flash and see what happens.
Haha, otets nash. Prikol, odnako.
Otets_vash said:
what do you mean saying "can't install soti pocket controller" ?
Click to expand...
Click to collapse
i mean. i have to install it pc first and then xda. But i can't install it to pda becouse i'm stucked at align screen. i can't do anything! How can i install a program without skipping the align screen!? i have to find a program wich gives me chance to delete "welcome.ink" file from xda.
finnaly the situation is; i am at the begining of rom (align screen)
i can't install a program to device,
i can't remove welcome files becouse they are read only!
please help me help me help meee!!!
Try hard reset. If no joy - bootloader + reflash.
create blank file called "WELCOME.NOT" (without the quotes, for example you can use notepad) and copy it into the root of your SD card (card reader required),and soft reset. This way the welcome screen will be bypassed , but you have to allign the screen to make it usable from start=>settings=>system=>screen
If all fails, could it be the hardware problem, rather than soft?
Hello
sorry to ask this. but I need best Rom for my HTC TYTN1, because I always find myself with a problem I posted here :
http://forum.xda-developers.com/showthread.php?t=484219
Now I have the problem of two call buttons that do not work! just sometimes
I ask you if it is possible to redo my htc to zero! as he emerged from the factory for the 1st time!
I see no other solution.
help me please
Thank you
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
It sounds like you might be having some sort of hardware or button issues.
I don't know if it would help to do a hard reset or not. Make sure you back up your contacts and stuff first, or they will all be gone! You can hold both "softkey buttons" the buttons above the windows and ok buttons and hit reset, or go into system settings and run clear storage. But again, I'm not sure if that would help.
Or if your running a custom rom, you can try flashing your operators stock rom, or one of the at&t ones in my signature.
But if the buttons are going crazy, I'm still leaning towards something going on with some of the keys, or possibly even the hardware keyboard.
Has the phone been dropped? I have been reading some things about the ribbon cable coming undone or going bad that can cause odd issues.
Maybe someone else has experienced this, and can chime in?
Hi boog321
First, thank you for your answer
I just tried to restore but my buttons do not work
I downloaded now
Hermes Official AT & T shipped with WM6 Radio 1.54.07.00
I will Try, even if it is in English I think! what I need one in French! but essential to get my HTC well now
I already have a hard spl v7 and market,
it's good ?! or I should to do somthing after or I can do other hard !
Lately I bought a accesoire but I think that is the problem! by what I had the problem before you!
Cable Audio Multifonctions YC A300
and as I am new here and I have a little knowledge with the ROM and flash, I ask your help plz
thank you
You could try going to start>settings>system>clear storage
that is the equivalent to a hard reset.
or see if you can remove the software for the accessory.
hi !
I just install your 2 Rom's and still same problem ((((
what I must to do !!
m-graphique said:
hi !
I just install your 2 Rom's and still same problem ((((
what I must to do !!
Click to expand...
Click to collapse
It sounds like your buttons are dead
I've never had one of our phones apart yet, maybe somebody else here could point you in the right direction for instructions or direct you towards someone that could repair it.
I'm sorry that I can't help you beyond this.
I noticed
is that all the buttons in the front does not work, just the buttons of directions and ok works.
Now I want to know how to downgrade please, to get back to original rom / radio / spl and bootloader possible!
thx boog321
You can find a bunch of that stuff in the wiki. Hermes wiki
Available Original Shipped WM5 ROM Versions
Available Original Shipped WM6 ROM Versions
Available Extracted Radio Upgrade Only
Hopefully it has the one from your original provider listed.
thx again boog321
I tried a few ROM's but still same problem.
story by if can you please guide me to install windows 5!
thank you
Follow the link I gave above for WM5, then pick the one for your language and flash, just like the others.
that is what I do,
I run normally my ROM and after gives me Error 260 no answer the phone!
for info I have :
HERM200
IPL-1.04
HERM200
SPL-2.10.olipro
Maybe make sure both computer and phone are rebooted, then make sure activesync is connected to the phone. It needs to send commands to the phone.
If that doesn't work, I may be able to strip the rom down so it could be flashed via sd card. Just let me know, but to flash via sd card, it must be formatted fat32, and be 2 gig or less.
ROM doesn't need to be "stripped down"... Just format sd card FAT32 and copy .nbh file of ROM onto card, Rename to hermimg.nbh. Re-insert sd card into hermes and go to bootloader. If everything is right, follow the promps.
As boog321 said, It must be a 2Gb or less sd card.
Cheers...
I still reckon its a hardware problem though.
ultramag69 said:
ROM doesn't need to be "stripped down"... Just format sd card FAT32 and copy .nbh file of ROM onto card, Rename to hermimg.nbh. Re-insert sd card into hermes and go to bootloader. If everything is right, follow the promps.
As boog321 said, It must be a 2Gb or less sd card.
Cheers...
I still reckon its a hardware problem though.
Click to expand...
Click to collapse
I was thinking if it is like the at&t rom, it would need to be stripped then compiled back into a .nbh. Since it comes as an .exe
Sounds to me like it's a D-Pad problem, rather than a ROM problem.
Have u experienced any white-screen problems.
There is a thread dedicated to D-Pad problems, just search XDA.
I have repaired several TYTN 1s with either D-PAD or WSOD problems using the instructions gathered on this forum.
Nope, just unrar the .exe file and you'll see the .nbh file. You should download a stripped ROM from here though, has radio removed...
ultramag69 said:
Nope, just unrar the .exe file and you'll see the .nbh file. You should download a stripped ROM from here though, has radio removed...
Click to expand...
Click to collapse
Your, right, I had a huge brain fart! I was thinking of when I was playing with stripping the radio on my own. But, it had been so many beers ago!
Only difference is, that I use 7zip to extract it
Hi
Thank you for your answers
I dont know how, but I see that the buttons still works! just that sometimes and rarely now does not work!
I installed ROM version 3.62 / Radio 1.38.00.10
just the problem is that I found in English. and I'm good with windows and French and I already azerty keyboard ...
possible to change language of my TYTN without refueling ROM please?
Hello Dears,
kindly help me as my phone after hard reset stuck on dot view mode automaticly and i can't exit it or even setup my phone like gmail or lang ,
after five seconds after make har resest dot view mode apper and i can't exit it ,
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Best Regards ,
Redo the hard reset and try again. Also, I suspect that your screen is frozen (watch for changes in dot view mode, like time and battery percentage). It might also be that your tactile screen isn't working anymore and requires a change.
sharvyngunga said:
Redo the hard reset and try again. Also, I suspect that your screen is frozen (watch for changes in dot view mode, like time and battery percentage). It might also be that your tactile screen isn't working anymore and requires a change.
Click to expand...
Click to collapse
Thanks Dear for your replay ,
but the screen is not freezed as i can check my call history and time and battary status ,
also i made har reset and change all frim as i made new flash but problem still exist ,
Regards
Can you share a video of the boot process?
I'll try my best to help you, but I can't guarantee success.
sharvyngunga said:
Can you share a video of the boot process?
I'll try my best to help you, but I can't guarantee success.
Click to expand...
Click to collapse
Thanks Dear ,
i don't have another phone , but i will try to get new one ,
Thanks
Sorry, this is completely unrelated from the current topic but I reallly need help..I tried to flash a rom on my HTC but thr preloader got corrupted xo my phone go hard bricked. Pluging the phone into a computer just shows a red led and the computer shows nothing in device manager.
I tried uninstalling the MTK Preload VCOM driver and reinstalling it but that still didn't work.
Even pressing volume keys while connecting still gave nothing.
I also tried disconnecting the battery and reconnecting the phone to the computer but still nothing.
If there is anyone, please help me.....
I need to unbrick my phone................... I am begging, please help me.
When my E9 got hard bricked, I sent it to a repair shop. They took a long time, but they brought it back to life.
Now, I had a hard brick issue with a Lenovo P1M Vibe (also a MTK device). I solved it using SP TOOL and the proper files. I don't know why the app suddenly decided to detect my phone after dozens of tries. But, during my research, I found interesting articles:
How to get a PC detect and MTK device after flashing wrong ROM/Firmware (Test Point method)
Download the latest & updated stock rom firmware of popular phones like samsung, tecno, itel, infinix, etc with flashing & upgrade tools & instruction
www.romkingz.net
As for the software part of the solution:
[Guide/Info] [How To] Unbrick your Bricked MTK Devices (Dead Brick)
This thread is about how to recover the MTK Android phone, if it has gone Bricked (soft/hard/dead/etc) THIS IS FOR INFORMATION ONLY. Q. How Phone gets Bricked? Ans : Basically, phone get bricked during the installation of Android OS (flashing)...
forum.xda-developers.com
You will need additional files for your phone during this process. You can find them online.