Downgrade to factory default spl and rom? - P3600 ROM Development

I'm wondering how to do if one wants to downgrade to factory default spl, radio and rom without leaving any traces of wm6? Is there any guide available for this?
Flashing with wm5 rom from htc does not restore default spl.

aburman said:
I'm wondering how to do if one wants to downgrade to factory default spl, radio and rom without leaving any traces of wm6? Is there any guide available for this?
Flashing with wm5 rom from htc does not restore default spl.
Click to expand...
Click to collapse
I think it does restore SPL.
Try here: trinityguides.info

mikhe69 said:
I think it does restore SPL.
Try here: trinityguides.info
Click to expand...
Click to collapse
Sorry but it doesn't. No guide for downgrading on that site either.

http://rapidshare.com/files/67947675/SPL_IPL_SPLASH_ORIG.rar
Restore original IPL, SPL and Primary&Secondary Splash screen (IPL 0.50, SPL 1.0)

incorect said:
http://rapidshare.com/files/67947675/SPL_IPL_SPLASH_ORIG.rar
Restore original IPL, SPL and Primary&Secondary Splash screen (IPL 0.50, SPL 1.0)
Click to expand...
Click to collapse
Thanks a lot man, very appreciated!

Related

Help: Can't flash anything any more

Hallo everbody.
I'd really be glad, if you could help my with my problem:
I currently have bepe's german WM6 ROM v. 0.5 installed on my P3600. Now, the problem is, that I cannot flash anything anymore. When I start any rom update, the device enters boot loader, the progress bar gradually counts to 100% (a little faster, than I remember it doing before). At 100% the device turns off, but doesn't reboot itself. The rom update utility reports a success. When I then restart the device, everything is as before, without any changes.
My installed Hard SPL is SPL-9.99.CP. I tried to flash Olipro's new SPL without any luck. The SPL remains SPL-9.99.CP.
I don't know what to do any more...
have you installed Hard SPL by Oli 1.30????
if yes, downgrade to 1.20 version
psxsnake said:
have you installed Hard SPL by Oli 1.30????
if yes, downgrade to 1.20 version
Click to expand...
Click to collapse
Problem is, I have SPL-9.99.CP installed. It seems, that I even cannot flash to another SPL any more. I just tried to flash Oli 1.30 without any luck.
paranoid2007 said:
Problem is, I have SPL-9.99.CP installed. It seems, that I even cannot flash to another SPL any more. I just tried to flash Oli 1.30 without any luck.
Click to expand...
Click to collapse
SPL 9.99.CP will show with all HARD-SPLs I believe. Try to Flash HARD SPL 1.2 - and then try flashing again.
Lots of people could not flash anything with HARD SPL 1.3 flashed.
nealed said:
SPL 9.99.CP will show with all HARD-SPLs I believe. Try to Flash HARD SPL 1.2 - and then try flashing again.
Lots of people could not flash anything with HARD SPL 1.3 flashed.
Click to expand...
Click to collapse
Could you point me to SPL v. 1.2? I can't find it via the forum search.
nealed said:
SPL 9.99.CP will show with all HARD-SPLs I believe.
Click to expand...
Click to collapse
No you are wrong! SPL 9.99.CP is DES HARD-SPL and CP mean CrashProof.
IPL x.x.50xx is show with every HARD-SPL.
SPL 9.99.CP is okay! Have you tried to flash a original WM5 Rom?
sammy_deluxe said:
No you are wrong! SPL 9.99.CP is DES HARD-SPL and CP mean CrashProof.
IPL x.x.50xx is show with every HARD-SPL.
SPL 9.99.CP is okay! Have you tried to flash a original WM5 Rom?
Click to expand...
Click to collapse
No. If it might help, I'll try. Can you point me to where I can get an original german WM5 Rom?
Ok, found the original ROM Update from the HTC site. Flashed it. This time the device rebooted by itself. Result: I am still stuck with the bepe ROM 0.5. Updating did nothing!
paranoid2007 said:
Ok, found the original ROM Update from the HTC site. Flashed it. This time the device rebooted by itself. Result: I am still stuck with the bepe ROM 0.5. Updating did nothing!
Click to expand...
Click to collapse
try this way! http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing
sammy_deluxe said:
try this way! http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing
Click to expand...
Click to collapse
Doesn't work. Whenever I try to start Hard SPL, the bootloader shows up for about 5 seconds. Then the screen slowly starts fading to dark grey, so that I can't read anything on the display. Then nothing more happens.
try goin into the bootloader screen on the device first rather that using the update tool first.. this should work
steveecourt said:
try goin into the bootloader screen on the device first rather that using the update tool first.. this should work
Click to expand...
Click to collapse
OMG this worked! Thanks a million. Strangely enough, I tried it this morning without luck.
I also have SPL 9.99 CP and if you put a rom on the flash card it just seems to ignore the file and goes backk into bootloader
steveecourt said:
I also have SPL 9.99 CP and if you put a rom on the flash card it just seems to ignore the file and goes backk into bootloader
Click to expand...
Click to collapse
I have the same SPL but I had never flashed a rom from Flash card.. Could you explain more in the deep how it works? did it once with older Rom's?

SPL 2.03 Problems

Hi,
I recently had my diamond return to me from HTC (screen repair) and as part of the normal process they flash the latest rom when they return the device.
Now i have the latest 2.03 rom and 2.03 SPL (did not know there was a 2.03 SPL)
Now for the problem..... I cant seem to flash to a hard SPL ie 1.24 or 1.40, i have tried them all and i have tried the manual method (no luck).
Prior to me sending off my diamond i had flashed the 1.24 spl with no issues.
I have looked all over the forum and i can't find any mention of a 2.03 SPL and i am wondering is this new SPL prevents you from flashing to any older/other SPL versions.
If any one has any ideas please help.
_)_?_:?
problems because of the SPL?
There is a good part to the new SPL?
could someone get this SPL? for a separate installation?
thanks :d
Yeah it is strange i had no idea there was a new one until i tried to flash and it shows spl 2.03 on the boot loader screen.
If someone knows how i can get a copy of this SPL off my device i will post it for all to look at.
bump...Loads of people have looked at this, no one with any ideas ??
if i remember corectly i had it on my phone also, but i could change it...
littlej said:
if i remember corectly i had it on my phone also, but i could change it...
Click to expand...
Click to collapse
ahhh interesting..... which SPL do you now have on your diamond ?
You have to use SSPL.
Just flashed HardSPL 1.24 over 2.03.
...
y want to instal spl 2.03 to test a modified room

Urgent! My diamond has hardware problem and need to fallback to stock ROM and SPL.

Hi,
My Diamond has no response on the screen, so I think I need to return to factory for repairing. However I have difficulties in falling back to stock ROM and SPL.
From the Wiki:
---------------
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
...
-----------------
I can't flash my ROM to latest HK WWE CSL ROM (2.03) as it just stopped at 0%. I'm using SPL-1.30.OliNex.
Questions:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
1) Should I flash to v1.93 (the very beginning of the ROM)?
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
3) Anyone can give me a reference on the step-by-step in details...
Thanks!
Please help...
F810
Questions:
f810 said:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
Click to expand...
Click to collapse
If the latest was the offical from the site then you could use that - as you are having issues flashing this with 1.30 HSPL, I would suggest updating that to 1.40
f810 said:
1) Should I flash to v1.93 (the very beginning of the ROM)?
Click to expand...
Click to collapse
This might be a easier option and should work woth the 1.30 HSPL
f810 said:
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
Click to expand...
Click to collapse
This is recommended
f810 said:
3) Anyone can give me a reference on the step-by-step in details...
Click to expand...
Click to collapse
Its really straight forward like the WiKi suggests
This Thread may help
Thanks a lot.
Re Q3, so do you mean if I extracted the stock NBH, it's only OS but not including RADIO? If so, I will get the RADIO from wiki page later. Would you please clarify for me?
After your information, I think the steps in Wiki are clear. Thanks.
If this is HK ROM is the one you have downloaded from HTC PAGE then it has a radio included
Since my Diamond is totally malfunction in the touch screen, I can't response to all the confirmation & prompts...
I've failed to install Stock ROM and tried your recommendation on upgrading to HSPL 1.40. There was a confirmation on running the program in my Diamond and I can't press YES and now my diamond is just like bricked.
I've also tried pressing VOL DOWN + Reset to connect the Diamond via USB. The ROM Update Utility has "successfully" update the HSPL, but actually when I hard reset it and found it's still running 1.30... Can I just use this approach to fallback to Factory status??
Anyone has good idea on how to fallback to Factory Stock ROM, RADIO and SPL, provided that my screen has totally no response to me?
PLEASE...PLEASE...PLEASE help.
You will not be able to update olipros Hard SPL in bootloader mode as the SPL is protected and the 1.30 will prevent this although show its been done.
What you will need to do then is just load a 1.93 ROM from boot loader. the were some in that link i posted earlier. as to reverting to the default SPL - you may be luck not to need the screen for any confirmation. but running a new SPL to overwrite Oli's you will need to use windows and the RRU
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
band27 said:
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
Click to expand...
Click to collapse
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Here you go....I did a search
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Read this............Scroll to Post #39
http://forum.xda-developers.com/showthread.php?t=400950&page=4
band27 said:
Here you go....I did a search
Click to expand...
Click to collapse
I also got that but it's not win32 program... I believe it's running on the Diamond. But I've hard reset, and never able to setup as it's screen was not functioning now...
kawatsu said:
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Click to expand...
Click to collapse
That ROM had a different boot image - so you need to replace that by flashing another splash .NBH file using RUU.
Original splash can be found HERE
and if needed CUSTOM RUU HERE
Just un-zip these and put the splash file in the same folder as the Custom RUU and run the RUU - the flash should take a few seconds and viola - bye bye Diamond project splash.
f810 said:
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Click to expand...
Click to collapse
I think as long as the SPL is changed and the ROM is of the original language the I think it should be OK to send back like that
f810 said:
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Click to expand...
Click to collapse
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Which is the original SPL?? 1.23, 1.34 or 1.37? I do recall taking a picture of the original SPL when i 1st got the Diamond for days like that but i just can't find it now
I'm bought it from Malaysia. Anybody can help me confirm this??
R3PUBL1K said:
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Click to expand...
Click to collapse
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
f810 said:
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
Click to expand...
Click to collapse
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
f810 said:
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
Click to expand...
Click to collapse
Can anyone help??

Hard spl problem!!!

I know you guys most be tired of this but im still a lil confused about all this since i have searched around and i have still to know how to return the stock SPL...now i know theres alot of post that show how but what i need to do is find out one which i dont have to use my phone:
What i mean is....i dont have to copy SSManual.bat to my fun and run it from my phone...because i have to return my phone to HTC for warranty reasons but i cannot get passed the align screen configuration at boot since my touch is messed up (p.s. i can still flash and active sync)...
what i need to know is a way to return to the stock SPL without using the phone (except for Active Sync)...
p.s. if i have the ASIA WWE HK ROM on the SPL would be 1.34 or 1.93?
thank you!!
[SOLVED]
Basically, thanks to the ppl in this thread for helping.....since i couldnt get passed my align screen cause of hardware problems with my screen i couldnt access the sspl-manual in order to revert to stock spl so what i did is i flash my phone with Dia duit 1.4 which has no welcome screen or align screen so i could go thru to the phone then performed the sspl manual and reverted to the 1.93 spl (my version)and afterwards i flash my phone with the Asia HTC wwe orginal romhttp://forum.xda-developers.com/showthread.php?t=410720 ......i know ure supposed to first flash orginal rom and then the stock spl but i took a chance and it worked...THANKS u guys keep up the good work and now its up to HTC to fix my hardware....Hoping its on warranty
By the way right now im on Olinex 1.40
thank you again!!!
can't you install the hardspl through bootloader mode?
Unfortunately no, everytime i do either i get an error [202] or it goes straight to 100% but then when i check with the vol - and reset button it shows olinex 1.40
did anybody ever try to send it without reverting back to the stock spl ?
emy09 said:
did anybody ever try to send it without reverting back to the stock spl ?
Click to expand...
Click to collapse
Try to install a rom which don't have to align the screen. then you copy the file you wants from the phone.
Good luck
does anybody know of a rom like that that exists cause that sounds like a pretty good idea!!
hi
i had your problem and has olinex 1.40 anld like to restore hard spl
first you should install original rom on your device
then install original hard spl ( i try it )
download rom 1.93 WWE from the htc site (it should be 1.93)
then hard spl with it (copy sspl manual om your device run it then restart you device run it again then connect it to pc and run ruu
hard spl : http://rapidshare.com/files/215819452/1.93_Original.rar.html
sorry my English is not good
http://forum.xda-developers.com/showthread.php?t=493719
emy09 said:
does anybody know of a rom like that that exists cause that sounds like a pretty good idea!!
Click to expand...
Click to collapse
i think the new rom of suiller (diadiut 1.4) would do. you don't need to screen align after flashing.
azera_2000 said:
hi
i had your problem and has olinex 1.40 anld like to restore hard spl
first you should install original rom on your device
then install original hard spl ( i try it )
download rom 1.93 WWE from the htc site (it should be 1.93)
then hard spl with it (copy sspl manual om your device run it then restart you device run it again then connect it to pc and run ruu
hard spl : http://rapidshare.com/files/215819452/1.93_Original.rar.html
sorry my English is not good
Click to expand...
Click to collapse
I appreciate the help but the problem is that i cannot get passed the align screen of the first boot which means i cant run sspl manual since i cannot in the files from my phone.....also if i do flash the Dia duit 1.4 rom which does not boot with the align screen or welcome screen, dont i have to flash the original rom before putting the stock SPL !!.....thank you guys for the info

Trouble restoring stock SPL

My Diamond touch keeps resetting itself continously, so i want to return it bacause i still have warranty.
The SPL is however unsigned (Olnex 1.40 unsigned), so no warranty. I found a guide for restoring the stock SPL, but i can only get into the bootloader, not into the OS to run the SSPL-utility.
Is there a way to restore the stock SPL in the bootloader? I tried several times, but the current SPL is write-protected
Fixed it with mtty
frankem said:
My Diamond touch keeps resetting itself continously, so i want to return it bacause i still have warranty.
The SPL is however unsigned (Olnex 1.40 unsigned), so no warranty. I found a guide for restoring the stock SPL, but i can only get into the bootloader, not into the OS to run the SSPL-utility.
Is there a way to restore the stock SPL in the bootloader? I tried several times, but the current SPL is write-protected
Click to expand...
Click to collapse
Hi
You have to start flash the stock spl from windows mobile and AS/WMDC and not from Bootloader
Goodluck
how to flash spl from original to remaked with mtty?

Categories

Resources