Help: Can't flash anything any more - P3600 ROM Development

Hallo everbody.
I'd really be glad, if you could help my with my problem:
I currently have bepe's german WM6 ROM v. 0.5 installed on my P3600. Now, the problem is, that I cannot flash anything anymore. When I start any rom update, the device enters boot loader, the progress bar gradually counts to 100% (a little faster, than I remember it doing before). At 100% the device turns off, but doesn't reboot itself. The rom update utility reports a success. When I then restart the device, everything is as before, without any changes.
My installed Hard SPL is SPL-9.99.CP. I tried to flash Olipro's new SPL without any luck. The SPL remains SPL-9.99.CP.
I don't know what to do any more...

have you installed Hard SPL by Oli 1.30????
if yes, downgrade to 1.20 version

psxsnake said:
have you installed Hard SPL by Oli 1.30????
if yes, downgrade to 1.20 version
Click to expand...
Click to collapse
Problem is, I have SPL-9.99.CP installed. It seems, that I even cannot flash to another SPL any more. I just tried to flash Oli 1.30 without any luck.

paranoid2007 said:
Problem is, I have SPL-9.99.CP installed. It seems, that I even cannot flash to another SPL any more. I just tried to flash Oli 1.30 without any luck.
Click to expand...
Click to collapse
SPL 9.99.CP will show with all HARD-SPLs I believe. Try to Flash HARD SPL 1.2 - and then try flashing again.
Lots of people could not flash anything with HARD SPL 1.3 flashed.

nealed said:
SPL 9.99.CP will show with all HARD-SPLs I believe. Try to Flash HARD SPL 1.2 - and then try flashing again.
Lots of people could not flash anything with HARD SPL 1.3 flashed.
Click to expand...
Click to collapse
Could you point me to SPL v. 1.2? I can't find it via the forum search.

nealed said:
SPL 9.99.CP will show with all HARD-SPLs I believe.
Click to expand...
Click to collapse
No you are wrong! SPL 9.99.CP is DES HARD-SPL and CP mean CrashProof.
IPL x.x.50xx is show with every HARD-SPL.
SPL 9.99.CP is okay! Have you tried to flash a original WM5 Rom?

sammy_deluxe said:
No you are wrong! SPL 9.99.CP is DES HARD-SPL and CP mean CrashProof.
IPL x.x.50xx is show with every HARD-SPL.
SPL 9.99.CP is okay! Have you tried to flash a original WM5 Rom?
Click to expand...
Click to collapse
No. If it might help, I'll try. Can you point me to where I can get an original german WM5 Rom?

Ok, found the original ROM Update from the HTC site. Flashed it. This time the device rebooted by itself. Result: I am still stuck with the bepe ROM 0.5. Updating did nothing!

paranoid2007 said:
Ok, found the original ROM Update from the HTC site. Flashed it. This time the device rebooted by itself. Result: I am still stuck with the bepe ROM 0.5. Updating did nothing!
Click to expand...
Click to collapse
try this way! http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing

sammy_deluxe said:
try this way! http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing
Click to expand...
Click to collapse
Doesn't work. Whenever I try to start Hard SPL, the bootloader shows up for about 5 seconds. Then the screen slowly starts fading to dark grey, so that I can't read anything on the display. Then nothing more happens.

try goin into the bootloader screen on the device first rather that using the update tool first.. this should work

steveecourt said:
try goin into the bootloader screen on the device first rather that using the update tool first.. this should work
Click to expand...
Click to collapse
OMG this worked! Thanks a million. Strangely enough, I tried it this morning without luck.

I also have SPL 9.99 CP and if you put a rom on the flash card it just seems to ignore the file and goes backk into bootloader

steveecourt said:
I also have SPL 9.99 CP and if you put a rom on the flash card it just seems to ignore the file and goes backk into bootloader
Click to expand...
Click to collapse
I have the same SPL but I had never flashed a rom from Flash card.. Could you explain more in the deep how it works? did it once with older Rom's?

Related

URGENT help on Hard SPL screen

Hello,
I executed the Hard SPL cab and went into bootloader or some sort of a multi colored screen which says IPL - 0.50 Trin100 and underneath it says SPL 3.03.0000. It connects to my computer and says USB but when I attempt to flash the new WM6 rom which I just downloaded from the rapidshare it resets the machine and continues to remain on this screen of multi colored stuff. I cannot seem to get out of it no matter what I do. What do i need to do to abort the multi colored screen or allow it to flash my HTC trinity with the Dopod WM6 rom?
Thanks,
Gilbert
PS: please don't shoot me if this was discussed elsewhere. i searched and could not fine anyting
happened to me yesterday.
with this screen install AGAIN the hard....
see
http://forum.xda-developers.com/showthread.php?t=316113
and
http://forum.xda-developers.com/showthread.php?t=312499 -page 45
How? I try to execute again the Hard SPL file and it gives me an error and says close window on PC.
Thanks,
Gilbert
it keeps giving me error in connection and i think i bricked my phone i tried to reinstall several times and i get the same results. Poor me.
Same hapen to me, then ive tried to instal over it a another rom and it came to life.
if you're in the bootloader already, try and run the RUU (update program) again on your pc after reconnecting your device.. if that doesn't work, please give details of the error. I don't think you're bricked yet
racerx_ said:
if you're in the bootloader already, try and run the RUU (update program) again on your pc after reconnecting your device.. if that doesn't work, please give details of the error. I don't think you're bricked yet
Click to expand...
Click to collapse
Thanks for your help. I get Error 260:
The update utility cannot connect to your pda. please check usb is connected. click exit to quit.
When I try to run the upgrade alone in XP it starts at 1% then resets the bootloader.
Thanks,
Gilbert
k which upgrade are you running? still trying to get hard spl working, or running the Dopod WM6 upgrade?
*i've been having some troubles upgrading today too, with the WM6.. scary times ha*
racerx_ said:
k which upgrade are you running? still trying to get hard spl working, or running the Dopod WM6 upgrade?
*i've been having some troubles upgrading today too, with the WM6.. scary times ha*
Click to expand...
Click to collapse
I am trying to upgrade the
RUU_Trinity_DOPODASIA_WWE_3.00.707.17_6275_1.46.00.11_108_Ship but i also tried to reflash the 1.23 HTC rom with GPS to see if it would flash since my device is an HTC trinity and not dopod but the same thing keeps happening.
Try to flash PDAVIET version, my came to life doing this
have you tried to flash any other ROM? I was stuck with the same thing, but managed to flash a cooked ROM..
what's your bootloader showing?
if you fail to flash any other ROM, i think you need to try the stack overfow exploit posted here.. http://forum.xda-developers.com/showthread.php?t=308691&highlight=error+206
it's a bit technical, but i think it's your best bet if all else fails.. Pof might be able to help you over there
No matter what i do, what rom i try to flash i get the same damn error message: Error 260 - Connection!!! I am connected so I don't what is wrong with it. I will try some more then decide to take a hammer and break it into 1000 peices.
Thanks.
racerx_ said:
have you tried to flash any other ROM? I was stuck with the same thing, but managed to flash a cooked ROM..
what's your bootloader showing?
if you fail to flash any other ROM, i think you need to try the stack overfow exploit posted here.. http://forum.xda-developers.com/showthread.php?t=308691&highlight=error+206
it's a bit technical, but i think it's your best bet if all else fails.. Pof might be able to help you over there
Click to expand...
Click to collapse
My bootloader is showing the following:
Trin100
IPL-0.50
Trin100
SPL-3.03.0000
Thanks for all your help.
hmmm... i'm not familiar with that SPL number... unless somehow that got halfway updated with the WM6 update.
I think you better head to that thread and try the stack exploit. Did you try loading a cooked ROM to see what happens?
that is it. i give up. i am not experienced in messing with codes. i am going to retire the device for good and use a regular phone. this is crap. thanks for ur help.
oh, that is the SPL version of the new ROM... i guess you weren't using hard spl when you tried to flash it?
ha, well don't give up too quick.. that's one expensive retired device you've got there.
Just keep cool and you should try to install an official Rom to downgrade this SPL !!
Gilbert said:
I will try some more then decide to take a hammer and break it into 1000 peices.
Thanks.
Click to expand...
Click to collapse
Help!
My bootloader is showing the following:
Trin100
IPL-1.00
Trin100
SPL-9.99.CP
When upgrading with the new released WM6 ROM, it keeps failing at 28%
Please help!
best bet for you, is load a different ROM now. Either cooked or official. That will get your device out of crash-proof spl bootloader.
Once the ROM is loaded, if you want to try the official wm6 again, run SSPL first and see if it'll work for you
p.s. i pm'd you my handphone number in case you've got trouble still..
Gilbert said:
My bootloader is showing the following:
Trin100
IPL-0.50
Trin100
SPL-3.03.0000
Thanks for all your help.
Click to expand...
Click to collapse
Hi Gilbert,
Im having exactly the same problem as you. Right now im in the middle of flashing it back down to WM5 (its working at the moment at 17%).
Hopefully after this i will be able to flash back to WM6 (Most probably will go back to AX3L for now).
Hope this helps you out (im quite stressed about it too!)
Edit: I have just finished flashing to Official WM5, now flashing back to AX3L WM6. It works!

Stuck at 28% help needed

Stuck at 28% of upgrade
phone is showing 4 colors and does nothing
PLEASE PROVIDE LINK TO BE SAVED
LINKS AND INFO WHAT TO DO IN DETAIL
I AM NOT A COMPUTER GUY
flash official rom back. Then download this rom
http://rapidshare.com/files/42141641/Wm6_Official.zip
and flash that one,
link for official rom ?
i remind you the phone is at the 4 colors mode
this page has all official roms ever made for trinity
http://wiki.xda-developers.com/index.php?pagename=Trinity_Upgrades
pkaza said:
link for official rom ?
i remind you the phone is at the 4 colors mode
Click to expand...
Click to collapse
Don't panic, the phone is not dead. You will get it fixed. Just follow the instructions given, there is a solution.
updated with official rom
hardspl does nothing
other way
?
Help me too!!! I don't even have an official ROM for my Orange m700
ward777 said:
Help me too!!! I don't even have an official ROM for my Orange m700
Click to expand...
Click to collapse
You could try this fix http://forum.xda-developers.com/showthread.php?t=316313&page=5
I don't think so. My Hard-SPL was overwritten and now has the 3.0 version and not SPL version 9.99.
9.99 is NOT Hard-SPL, it's Des's Crashproof spl which is not even trying to prevent itself from being overwritten.
OliPro?
Hello
What about OliPro SPL-1.20.Olipro with IPL-0.5
Can it also be overwritten or wich hard spl do I need first to flash?
Roman
don't worry , simply follow the instruction and reflash it again with the new rom , then it will pass through the 28% ...
Shadowmite said:
9.99 is NOT Hard-SPL, it's Des's Crashproof spl which is not even trying to prevent itself from being overwritten.
Click to expand...
Click to collapse
I know that
But I did have Hard-SPL and now it's gone so it will get overwritten when installing this ROM as well
tony800708 said:
don't worry , simply follow the instruction and reflash it again with the new rom , then it will pass through the 28% ...
Click to expand...
Click to collapse
What instructions?
ward777 said:
What instructions?
Click to expand...
Click to collapse
I guess you're in a pickle. There must be a way around not having an official Orange rom. Have you tried the SD card method from an Orange rom dump? Otherwise, the rom cookers should be able to come up with something. With all of these people trying these roms certainly you must not be the only one with an Orange phone. Good luck .
Hi Guys,
I am also stuck @ bootloader. I have the original rom, but how do I flash this back? It keeps on telling me that it cannot detect the phone. What can I do? Thank you!
You can flash the spl from the bootloader via mtty, but that's not something Ive seen clear instructions on how to do... you might want to log into #xda-devs in freenode IRC and get stepped through it.
If you're stuck at the bootloader, just try running the hard-spl flash right from there...
ward777 said:
I know that
But I did have Hard-SPL and now it's gone so it will get overwritten when installing this ROM as well
Click to expand...
Click to collapse
Yeah, I thought deleting 'SPL.nbh' would prevent the RUU from installing the new SPL but the Hard-SPL got overwritten on flashing.
Kris
there are 2 spl entries in the release... spl.nb and spl.nbh... you have to remove both. also I'd remove the ipl.nb...
These are the files inside the exe:
EnterBootloader.exe
ErrorBattery.fig
ErrorUSB.fig
ModelID.fig
rapitool.exe
README.doc
ROMUpdateUtility.cfg
ROMUpdateUtility.exe
RUUGetInfo.exe
RUUResource.dll
RUU_signed.nbh
SPL.nbh
I suppose you meant to remove the .nb entries inside RUU_signed.nbh
Kris

Another one bites the dust...!?

My Diamond keeps on rebooting on me and is hard resetting itself randomly :-(
I had udK's latest flashed when that started, but reflashed 3 times now with other ROM's.
How can i make sure that my phone is broken, or is there any known way to fix this ?
Thanks for any help!
Which Hard SPL you got?
garlog said:
Which Hard SPL you got?
Click to expand...
Click to collapse
Hard-SPL 1.40 Olinex SIGNED - can try to upgrade to a newer version... Do you think that might help ?
Matmax said:
Hard-SPL 1.40 Olinex SIGNED - can try to upgrade to a newer version... Do you think that might help ?
Click to expand...
Click to collapse
Maybe, but look at these threads....
http://forum.xda-developers.com/showpost.php?p=2984793&postcount=4
http://forum.xda-developers.com/showthread.php?p=2905775#post2905775
http://forum.xda-developers.com/showthread.php?p=2895628
Flash the unsigned then reflash a working rom (e.g. AZATOR x2 WWE) and then HardReset.
If that does not work maybe something is wrong with your device (hardware).
garlog said:
Flash the unsigned then reflash a working rom (e.g. AZATOR x2 WWE) and then HardReset.
If that does not work maybe something is wrong with your device (hardware).
Click to expand...
Click to collapse
the hard reset is a very important step. dont forget to do this.

Urgent! My diamond has hardware problem and need to fallback to stock ROM and SPL.

Hi,
My Diamond has no response on the screen, so I think I need to return to factory for repairing. However I have difficulties in falling back to stock ROM and SPL.
From the Wiki:
---------------
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
...
-----------------
I can't flash my ROM to latest HK WWE CSL ROM (2.03) as it just stopped at 0%. I'm using SPL-1.30.OliNex.
Questions:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
1) Should I flash to v1.93 (the very beginning of the ROM)?
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
3) Anyone can give me a reference on the step-by-step in details...
Thanks!
Please help...
F810
Questions:
f810 said:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
Click to expand...
Click to collapse
If the latest was the offical from the site then you could use that - as you are having issues flashing this with 1.30 HSPL, I would suggest updating that to 1.40
f810 said:
1) Should I flash to v1.93 (the very beginning of the ROM)?
Click to expand...
Click to collapse
This might be a easier option and should work woth the 1.30 HSPL
f810 said:
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
Click to expand...
Click to collapse
This is recommended
f810 said:
3) Anyone can give me a reference on the step-by-step in details...
Click to expand...
Click to collapse
Its really straight forward like the WiKi suggests
This Thread may help
Thanks a lot.
Re Q3, so do you mean if I extracted the stock NBH, it's only OS but not including RADIO? If so, I will get the RADIO from wiki page later. Would you please clarify for me?
After your information, I think the steps in Wiki are clear. Thanks.
If this is HK ROM is the one you have downloaded from HTC PAGE then it has a radio included
Since my Diamond is totally malfunction in the touch screen, I can't response to all the confirmation & prompts...
I've failed to install Stock ROM and tried your recommendation on upgrading to HSPL 1.40. There was a confirmation on running the program in my Diamond and I can't press YES and now my diamond is just like bricked.
I've also tried pressing VOL DOWN + Reset to connect the Diamond via USB. The ROM Update Utility has "successfully" update the HSPL, but actually when I hard reset it and found it's still running 1.30... Can I just use this approach to fallback to Factory status??
Anyone has good idea on how to fallback to Factory Stock ROM, RADIO and SPL, provided that my screen has totally no response to me?
PLEASE...PLEASE...PLEASE help.
You will not be able to update olipros Hard SPL in bootloader mode as the SPL is protected and the 1.30 will prevent this although show its been done.
What you will need to do then is just load a 1.93 ROM from boot loader. the were some in that link i posted earlier. as to reverting to the default SPL - you may be luck not to need the screen for any confirmation. but running a new SPL to overwrite Oli's you will need to use windows and the RRU
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
band27 said:
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
Click to expand...
Click to collapse
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Here you go....I did a search
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Read this............Scroll to Post #39
http://forum.xda-developers.com/showthread.php?t=400950&page=4
band27 said:
Here you go....I did a search
Click to expand...
Click to collapse
I also got that but it's not win32 program... I believe it's running on the Diamond. But I've hard reset, and never able to setup as it's screen was not functioning now...
kawatsu said:
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Click to expand...
Click to collapse
That ROM had a different boot image - so you need to replace that by flashing another splash .NBH file using RUU.
Original splash can be found HERE
and if needed CUSTOM RUU HERE
Just un-zip these and put the splash file in the same folder as the Custom RUU and run the RUU - the flash should take a few seconds and viola - bye bye Diamond project splash.
f810 said:
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Click to expand...
Click to collapse
I think as long as the SPL is changed and the ROM is of the original language the I think it should be OK to send back like that
f810 said:
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Click to expand...
Click to collapse
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Which is the original SPL?? 1.23, 1.34 or 1.37? I do recall taking a picture of the original SPL when i 1st got the Diamond for days like that but i just can't find it now
I'm bought it from Malaysia. Anybody can help me confirm this??
R3PUBL1K said:
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Click to expand...
Click to collapse
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
f810 said:
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
Click to expand...
Click to collapse
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
f810 said:
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
Click to expand...
Click to collapse
Can anyone help??

Device hang up on "Preparing for first use"

Hello,
i have a big problem.
After the installation of some Roms i have to do a hard reset becaue my Diamond chrashes.
So now I installed another Rom and the "Preparing your device for first use" screen appears but after this, nothing appens.
So i don't have any idea what i can do to fix this Problem...
Did anyone of you can help me please?
A little more inforation from you.
Might help to mention which rom you are having the issue with, which Radio version etc.
Radio ist 1.09.25.23 and the Rom ist Udks new Topaz R2.
I have the same experience with udK Syrius Topaz R0. The device keeps hardresetting even after I have installed another rom. Eventually, I restored to stock rom and install another cooked rom again. The problem seems to have been solved.
There are other users having the same problem with this rom. Although some have reported no problem, I would keep watching before installing this rom again.
ichselbst said:
Hello,
i have a big problem.
After the installation of some Roms i have to do a hard reset becaue my Diamond chrashes.
So now I installed another Rom and the "Preparing your device for first use" screen appears but after this, nothing appens.
So i don't have any idea what i can do to fix this Problem...
Did anyone of you can help me please?
Click to expand...
Click to collapse
How long are you waiting on this screen. It does take a few minutes for it to finish what it's doing.
Oh i wait about half an hour...
Now I changed the Rom and flashes Aztor and all is working.
Is it possible that the version of HardSPL is the reason for the hang up with udk's Rom?
At the moment i use hard-SPL 1.4, but I don't know how i can install the 1.93 Version.
When I download the zip.package from this tread http://forum.xda-developers.com/showthread.php?t=400950 the package contains only the RUU_Signed.nbh file and I have no idea how to install this file?!
ichselbst said:
Oh i wait about half an hour...
Now I changed the Rom and flashes Aztor and all is working.
Is it possible that the version of HardSPL is the reason for the hang up with udk's Rom?
At the moment i use hard-SPL 1.4, but I don't know how i can install the 1.93 Version.
When I download the zip.package from this tread http://forum.xda-developers.com/showthread.php?t=400950 the package contains only the RUU_Signed.nbh file and I have no idea how to install this file?!
Click to expand...
Click to collapse
You need the custom RUU to flash the spl to your phone
Im sorry, it is maybe a bad question, but where can I find the Costum RUU?
Thanks for your help!
Prewien said:
You need the custom RUU to flash the spl to your phone
Click to expand...
Click to collapse
Custom RUU does not seem to work with olipro's SPL 1.93. Try this one HERE which I know works.
ichselbst all you need to do is unpack this and run the ROM Update utility (RUU) follow insructions and wait till screen staes finished.
Hope that helps

Categories

Resources