Develop Bugs

Trouble with Dopod WM6..

can't seem to get this upgrade to work. the updater stops at about 28 percent for me with an error (286? i think) and after that i'm stuck in bootloader. Every time after that, the updater wont even start.. (a different error).
i can flash successfully a cooked ROM, but can't get the official one to work. Could it be a conflict with Des' crash-proof SPL? That's the only thing i can think of at this point..

To me said invalid device id, and got stuck on the boot loader

try back to any old offical ROM
and then copy SSPL to PDA and run it on PDA
when bootloader appear, run WM6 offical updater
I got same problem too and get fix
good luck

update: since i managed to flash PDAVIET's rom, i thought i'd just try going back to Olipro's hard-spl and see what happens.. So i flashed it, entered bootloader and ran the WM6 update again, and SUCCESS!!
very strange though.. anyone have some thoughts as to why it wouldn't work under Des', or if this is just coincidence?

It installs a new bootloader that can't be hacked by the previous hacks I think.... I'm stuck in it too...
SPL-3.03.0000

racerx_ said:
update: since i managed to flash PDAVIET's rom, i thought i'd just try going back to Olipro's hard-spl and see what happens.. So i flashed it, entered bootloader and ran the WM6 update again, and SUCCESS!!
very strange though.. anyone have some thoughts as to why it wouldn't work under Des', or if this is just coincidence?
Click to expand...
Click to collapse
Hi racerx,
I've encountered the same problem as your, stuck at 28% ERROR [286] while flashing, and couldn't go over it even after recovery process following the instruction.
Could you please explain a bit more details about how to go back to Olipro's hard-spl and enter into bootloader?
Thanks, eager to flash the new ROM...

Well I was able to get out of it by running Pof's CID RUU Unlocker, however, it errors after 7%, and resets. It gets past the bootloader, however, it hardreset the phone...eh.

IT happened to me too - Update Error.
So should i go back to Official WM5 then update to WM6 (i had AX3L installed before and i just had to reflash back to AX3L coz of the error from WM6).
Kinda scared me.....LoL

well, to start with i had Des' Crash-Proof SPL on my phone... so after the updater hung at 28%, i remained in Des' bootloader. I then ran the RUU for pdaviet's ROM, which flashed successfully. After that was on and my trinity was up and running, i flashed Olipro's hard-spl. Then manually put it in bootloader again, and flashed the official ROM.
Let me say this, though. At this point, i think you should be content to get your device out of bootloader mode. This Dopod WM6 doesn't have so much to be desired in it compared to cooked ROM's on this forum, plus your bootloader will be stuck at version 3.xxxx which i don't know if anyone is sure how to deal with yet. I'm regretting flashing mine to official version. Should have waited for a chef to pack it up for me.
what does your bootloader say?

You need to actually have a device that this release is supported by. It flashes a new SPL but you can flash Olipros HARD SPL 1.20 straight over that once WM6 has flashed.
It replaces any HARD SPL before flashing, probably to ensure only official devices get this update. Those having issues are probably out of this.
The official rom is fine, not as finished or customised as some chef ones, but good none the less. Also, the new 3.0??? SPL is no issue at all and easily removed once flashed.

yeah saw your post on the other thread.. thanks for the tip! talk about a stressful morning haha..
i was waiting for this ROM cause my activesync has mysteriously stopped working for a couple of weeks. so i was going to flash and take it to the service center. The miracle of it, was after my device hung and i reflashed pdaviet's rom, my activesync mysteriously works now even though i reflashed a million times before trying to get it going haha..

new spl is needed for flashing new radio rom with cid locked device.
So that's why RUU reflashes SPL at first.
U could simply reflash HArd spl back by using sspl

mUn, when can we expect your much anticipated "Indigo" rom using this offical WM6 base??

Genius! thanks for the tip mun...
all i can say is one word....
INDIGOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO!!

I also got Invalid vendor ID when I tried to flash for the first time. But it flashed just fine after I put it into bootloader mode. Give it a try..

Flashed my mine in a breeze from LSVW version 27/05/07.

myppcsg said:
Flashed my mine in a breeze from LSVW version 27/05/07.
Click to expand...
Click to collapse
still same problem
can you post the RUU files plz

mxlaser said:
You need to actually have a device that this release is supported by. It flashes a new SPL but you can flash Olipros HARD SPL 1.20 straight over that once WM6 has flashed.
It replaces any HARD SPL before flashing, probably to ensure only official devices get this update. Those having issues are probably out of this.
The official rom is fine, not as finished or customised as some chef ones, but good none the less. Also, the new 3.0??? SPL is no issue at all and easily removed once flashed.
Click to expand...
Click to collapse
Thanks for all the helps from you guys. This is what I did after stuck at 28% with ERROR[286]:
1. Flash back to Official OZ WM5 ROM. Had no problem to flash back as it was in the bootload mode.
2. Flash Olipro's Hard-spl. No problem as well.
3. Flash Official OZ WM6 ROM again...... and stuck at 28% again!!!!!! with ERROR [262] @#[email protected]#$.
4. Now in the process flash back to Official WM5 again... @#@#@....
5. Will flash Official WM6 straightaway after that.
6. Will update result later....

geoffreyhan said:
Thanks for all the helps from you guys. This is what I did after stuck at 28% with ERROR[286]:
1. Flash back to Official OZ WM5 ROM. Had no problem to flash back as it was in the bootload mode.
2. Flash Olipro's Hard-spl. No problem as well.
3. Flash Official OZ WM6 ROM again...... and stuck at 28% again!!!!!! with ERROR [262] @#[email protected]#$.
4. Now in the process flash back to Official WM5 again... @#@#@....
5. Will flash Official WM6 straightaway after that.
6. Will update result later....
Click to expand...
Click to collapse
hehe i did that many time this day maybe hmmm 5 or 6 and im still doing that

try to use another version of RUU (the older one)
ps. plz don't post messages about indigo in other tgreads ) if u want to ask - so ask in mine thread.
I'll flash official rom today and then will make some conclusion ) but i thibk that indigo will be based on oficial release

Orange HTC touch diamond ROM update

Hello i have a HTC orange Touch Diamond and i want to update the ROM as it is terrible. I am not that technical. can someone please explain what i need to do from scratch.
Thank you

I suggest your search the forum...

hello newbie
yes use the search button...it works really well

You first need to flash your diamond with one of the hard spl on this site and after you've done that you can take your pick from any of the roms on here

sorry guys i did look just didnt understand much. I am trying to use Hard SPL just cant get it to work.

same here
I have an orange htc Diamond and would really apreciate which files wouldwork. Everything I have tried stay's at Zero and ends up in an error.
Any help would be greatly ppreciated

root directory
to use hard spl i have to put a file in the root directory! but what is the root directory?

Hi James, your failing at 0% most likely because the SPL your using will not allow unsigned ROM's. Look for another SPL, one with developer edition in the title is good and works quite well for me.
I have an Orange also, the first thing to do is install the SPL then flash the radio (.05 is good) then get a new ROM!
Hope this helps

i think i broke my phone!!!!!
lol
i put the 2 files sspl and jump into my Diamond then i run sspl from my diamond and my phone resets.
The background image flashs a bit now. I still cant update the ROM and ideas what im doing wrong?

james soules said:
i think i broke my phone!!!!!
lol
i put the 2 files sspl and jump into my Diamond then i run sspl from my diamond and my phone resets.
The background image flashs a bit now. I still cant update the ROM and ideas what im doing wrong?
Click to expand...
Click to collapse
You need to do the following
1. Download the Unsigned HardSPL 1.24 from here http://forum.xda-developers.com/showthread.php?t=408621 and extract to a folder on your PC. Make sure you have Active sync installed and setup with your Diamond. Run the Updater in the 1.24 folder. Once the Phone reboots reconnect with active sync.
2. Download any of the ROMS on here and run the ROM to flash the phone.
Thats it !!!!!
Topboy

as i go to add a ROM i get a error saying the application failed to initialize properly ( 0xc0000135) click OK to terminate

Or check www.modmydiamond.info for easy to understand information

i get the above error as i try to add RUU

Hard SPL won't work
Hello,
From what I've read on the forum and also on www.modmydiamond.info, I gather I need to go through the Hard SPL step before installing any ROM.
However, after trying 2 different SPLs (hard_spl.120 and diamond_hspl_1.24) it still doesn't work.
I'm stuck at 0%.
Thanks

Read here....
As an alternative to the other threads try this one:
http://forum.xda-developers.com/showthread.php?t=416211
Its about the most comprehensive writeup I've seen to quickly and easily get your Diamond set from HardSPL to Radios to ROM's
Also read the WiKi's section at the top of the forum......

Query on Orange htc Upgrade ROM.
Hi There,
I have recently purchased a htc diamond, it was originally an Orange unit but is unblocked.The ROM version is 1.37 but I wish to flash to 1.93.I have the Orange released version of the 1.93 as htc wont support me direct.Question is, if I do this will the unit revert back to being Orange??ie.....does this flash the radio back?? or will it remained unblocked??
Thanks in advance...

james soules said:
Hello i have a HTC orange Touch Diamond and i want to update the ROM as it is terrible. I am not that technical. can someone please explain what i need to do from scratch.
Thank you
Click to expand...
Click to collapse
thxthxthxthx

Urgent! My diamond has hardware problem and need to fallback to stock ROM and SPL.

Hi,
My Diamond has no response on the screen, so I think I need to return to factory for repairing. However I have difficulties in falling back to stock ROM and SPL.
From the Wiki:
---------------
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
...
-----------------
I can't flash my ROM to latest HK WWE CSL ROM (2.03) as it just stopped at 0%. I'm using SPL-1.30.OliNex.
Questions:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
1) Should I flash to v1.93 (the very beginning of the ROM)?
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
3) Anyone can give me a reference on the step-by-step in details...
Thanks!
Please help...
F810

Questions:
f810 said:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
Click to expand...
Click to collapse
If the latest was the offical from the site then you could use that - as you are having issues flashing this with 1.30 HSPL, I would suggest updating that to 1.40
f810 said:
1) Should I flash to v1.93 (the very beginning of the ROM)?
Click to expand...
Click to collapse
This might be a easier option and should work woth the 1.30 HSPL
f810 said:
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
Click to expand...
Click to collapse
This is recommended
f810 said:
3) Anyone can give me a reference on the step-by-step in details...
Click to expand...
Click to collapse
Its really straight forward like the WiKi suggests
This Thread may help

Thanks a lot.
Re Q3, so do you mean if I extracted the stock NBH, it's only OS but not including RADIO? If so, I will get the RADIO from wiki page later. Would you please clarify for me?
After your information, I think the steps in Wiki are clear. Thanks.

If this is HK ROM is the one you have downloaded from HTC PAGE then it has a radio included

Since my Diamond is totally malfunction in the touch screen, I can't response to all the confirmation & prompts...
I've failed to install Stock ROM and tried your recommendation on upgrading to HSPL 1.40. There was a confirmation on running the program in my Diamond and I can't press YES and now my diamond is just like bricked.
I've also tried pressing VOL DOWN + Reset to connect the Diamond via USB. The ROM Update Utility has "successfully" update the HSPL, but actually when I hard reset it and found it's still running 1.30... Can I just use this approach to fallback to Factory status??
Anyone has good idea on how to fallback to Factory Stock ROM, RADIO and SPL, provided that my screen has totally no response to me?
PLEASE...PLEASE...PLEASE help.

You will not be able to update olipros Hard SPL in bootloader mode as the SPL is protected and the 1.30 will prevent this although show its been done.
What you will need to do then is just load a 1.93 ROM from boot loader. the were some in that link i posted earlier. as to reverting to the default SPL - you may be luck not to need the screen for any confirmation. but running a new SPL to overwrite Oli's you will need to use windows and the RRU

I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!

Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.

band27 said:
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
Click to expand...
Click to collapse
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?

Here you go....I did a search

Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!

Read this............Scroll to Post #39
http://forum.xda-developers.com/showthread.php?t=400950&page=4

band27 said:
Here you go....I did a search
Click to expand...
Click to collapse
I also got that but it's not win32 program... I believe it's running on the Diamond. But I've hard reset, and never able to setup as it's screen was not functioning now...

kawatsu said:
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Click to expand...
Click to collapse
That ROM had a different boot image - so you need to replace that by flashing another splash .NBH file using RUU.
Original splash can be found HERE
and if needed CUSTOM RUU HERE
Just un-zip these and put the splash file in the same folder as the Custom RUU and run the RUU - the flash should take a few seconds and viola - bye bye Diamond project splash.

f810 said:
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Click to expand...
Click to collapse
I think as long as the SPL is changed and the ROM is of the original language the I think it should be OK to send back like that

f810 said:
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Click to expand...
Click to collapse
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.

Which is the original SPL?? 1.23, 1.34 or 1.37? I do recall taking a picture of the original SPL when i 1st got the Diamond for days like that but i just can't find it now
I'm bought it from Malaysia. Anybody can help me confirm this??

R3PUBL1K said:
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Click to expand...
Click to collapse
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?

f810 said:
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
Click to expand...
Click to collapse
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...

f810 said:
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
Click to expand...
Click to collapse
Can anyone help??

touch diamond rom update

Hi i have a HTC TD device and I am traing to update rom from 1.93.401.2 to 2.03.401.2 but not sucssesifuly and at the end of update update utility shows this massage : 270 update error , the image file is corrupted, please check youre update utility.
This is frustrating because i tried all possibilities to fix a problem and still nothing, does anybody have any expirience with something like this to help me thanks a lot.

have you tried downloading the rom again?
Is your device locked by provider? If yes, you have to hardspl.

nickytheshaft said:
have you tried downloading the rom again?
Is your device locked by provider? If yes, you have to hardspl.
Click to expand...
Click to collapse
Yes I have tried all available posibilities : Hard Reset, changeing radio, and it is not locked by provider because first time i was sucssesifuly updated and then i saw olinex and i instaled that one after olinex there is no way to instal 2.03.401.2 I think that olinex is my problem but i do not have any idea to remove it because i have tried all available options and this is my 5th day that i am fighting with that and still i did not find any solution but anyway THANKS A LOT and get back to me soon if you know how to resolve this.

Diamond-HD said:
Yes I have tried all available posibilities : Hard Reset, changeing radio, and it is not locked by provider because first time i was sucssesifuly updated and then i saw olinex and i instaled that one after olinex there is no way to instal 2.03.401.2 I think that olinex is my problem but i do not have any idea to remove it because i have tried all available options and this is my 5th day that i am fighting with that and still i did not find any solution but anyway THANKS A LOT and get back to me soon if you know how to resolve this.
Click to expand...
Click to collapse
I seem to remember that error 270 means that you need to udate your bootloader, Try flashing an updated HardSpl.
And remember olinex has two spl's, one for gsm and one for cdma, they are not interchangeable.

thanks
Thank you i solved my problem i have know that olinex is for gsm and cdma i am fixed with hard spl 1.34 and now work perfect and after this long problem resolving now i know everithing about rom because i have try everything THANKS A LOT AND STAY GOOD AS WHOLE THIS SITE IS THANKS AGAIN

Error 270 when flashing to 2.03 stock firmware
I had the exact same problem. I went out on a limb and try something different and it worked! When you have just completed a fail upgrade (you see the 3 colored bars on your phones screen) quit the firmware update software, soft reset phone, re-connect to computer, and immediately flash to hard spl 1.34 signed. When finished the phone will reboot to and viola, you will have the latest firmware installed. At this point you can put back on the latest spl (1.40 I think) so that you can load custom ROM's. Just remeber if you want to get back to the latest stock ROM from HTC you have to rollback to the 1.34 SPL. Hope this helps peeps.

Flashing can't start, and cant't find solution the after searching the forum

So as you can figure out from the thread title I have a problem flashing my htc diamond.
I have installed a HardSPL version 1.30 OliNex, I can confirm that becouse on the three color screen there is a text saying "1.30 OliNex".
I still have the original ROM that comes with the phone when I bought it, so this meant to be my first flashing.
I want to flash the phone with this rom http://forum.xda-developers.com/showthread.php?t=593678 it is a WM 6.5 based ROM.
Because in the ROM package there wasn't a ROMUpdateUtility.exe I used it from other ROM package.
Connected via ActiveSync and followed the wizard. The phone reset and there came a gray screen with a progress bar. Now both progress bars on the phone and on the PC screen remain 0% and after a wile RUU finished with 262 ERROR Connection error, see the attached picture.
After that I tried to flash it from Internal Storage. A followed the steps according the procedure, and after the three colored screen it came the gray screen with "Loading..." message. I waited for almost 30 minutes and nothing happened.
What seems to be the problem?
I assumed about firewall disabling the connection. But I turned off the firewall and again the same story.
Then somewhere I found that there is incompatibility with the RUU and HardSPL version, but tried to flash with the same RUU that I used when I was installing HardSPL.
Then I tough that the problem is about flashing unsigned ROM on a signed HSPL, but it is not that the ROM is signed.
I am afraid to use MTTY so I don't brick my phone, because this is my first time flashing a Diamond.
I'm confused What seems to be the problem?
Any help can be welcomed.
Could this be indication of a hardware problem? When waiting for the "Loading..." message disappear the back cover warms a little.
Thanks.

1. Did you use the RUU from my thread?
2. NEVER USE AN H-SPL RUU TO FLASH ANYTHING OTHER THAN H-SPL!
3. is this a CMDA phone. IE, what network are you on?

Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?

Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?
EDIT: I did tried the RUU you recommended in your thread but it's the same.
I think it is in the PDA.

Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"

Hmmm..
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.

johnyboy_ said:
Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"
Click to expand...
Click to collapse
The connection between PC and PDA is made, because as I said there is a progress bar on the phone screen too.
djfuego said:
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.
Click to expand...
Click to collapse
As I understand you, you are saying to install later version of Hard SPL right?
So to install a new version of Hard SPL I just need to do the same procedure as the first time, or I have to uninstall the previous one?
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?

djandreski said:
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?
Click to expand...
Click to collapse
Presuming from your post, you are using a signed Olinex SPL, i doubt that the rom has been signed be OliNex, the only difference with Dev is you can flash any Rom, flash the Dev one from my thread, nothing to be afraid of
Good Luck
Badwolve1

What are the steps of installing new SPL?
Do I just need to do the same procedure as the first time, or I have to uninstall the previous one(somehow)?
UPDATE: I did it, I successfully flashed my Diamond PDA! It seams that the problem was in the SPL I installed 1.40 OliNex Unsigned and it flashed like a charm. Thanks guys for the help. Now this thread can be closed, or do I have to close it myself.

Great!
Glad it all worked out