MTTY - 8525, TyTN, MDA Vario II, JasJam ROM Development

All,
i'm trying to reflash bootloader to (hoping to) fix my lovely button problem!
After setting herm in boot mode (POWER+OK+RESET), connected the HERM to my PC, i run the MTTY utils and... this damn prg do not see any USB port.
If i use MTTY 1.16, the PC see only RS232 ports
If i use MTTY 1.42, the PC see only RS232 ports
If i use MTTY 0.01, the PC see USB port but answ me that the port cannot be opened.
Some one know this issue???
Tanks
RESOLVED Stopping activesync processes!
Again tanks

Perhaps you should explain your 'button problem' first as it might not require you to use mtty?

Related

Stucked to "Serial" bootloader mode

Hi all,
I was trying to upgrade my Qtek9000 with an official ROM Updater, but my device went immediately into the Serial bootloader mode and I've not been able to do nothing to run out from this mode...
I've tryied the solutions suggested in http://forum.xda-developers.com/showthread.php?t=290234 without any luck...
The problem is that neither Mtty nor the UNI_exitbootloader tool are able to connect to USB.
I'm using no usb hub, I'm running on a Dell Precision M90 notebook, I've disabled USB connection in Activesync (4.2.0) and also tryied with a pc without activesync installed.
Any idea?
Thanks
Paolo
Are you on XP or Vista, and what version of AS/WMDC do you have?
Hi,
I'm running Xp, ActveSync is 4.2.0, don't know what WMDC is sorry, can you please explain?
Don't worry about WMDC - it's only relevant if you have Vista.
Are you using the proper cable that came with the Universal? Some cables don't have all the pins wired. That (or a broken USB port) would explain why your Universal isn't going to USB mode when you plug in the USB cable. Have you looked carefully to see if it changes from saying "Serial" to "USB" at the top of the Bootloader screen when you plug in the cable?
If it does change to "USB", I would try upgrading to ActiveSync 4.5 - go to http://www.microsoft.com/windowsmobile/activesync/activesync45.mspx
Make sure you disable USB Connnections in the Connection settings before plugging in your Universal. Then try flashing the CE ROM again.
Good luck
BTW did you try doing a hard reset to get out of bootloader (both soft keys and then the reset button, then select 0).
Good advice, especially with upgrading to AS 4.5, it's a full release now on Microsoft Update site, and I have a feeling the WM6 ROMs may require it... Good luck with it, keep us posted.
Ok, thanks all!
This morning I connected the PDA to my office's PC with it's original cable and it instantly switched to USB mode...
So, I launched the upgrade and it's now in progress... let's hope!!!
It might really be a cable problem, yesterday night I tried with 2 different PC and a not original cable (I think it's my camera one...)
Thanks a lot, by now... I'll let you know own this story will end...
Ok, new ROM is up and running!
Thanks all!
Bye
Paolo
Good stuff.

USB connection does not work

hi
i have a diamond that when i connect to the USB cable ,it ask me normaly to chose betwen Activesync and mass storage but whatever i chose nothing happens on my pc and diamond itself.
my pc and my cable are ok because i can sync my friends diomond noramly.
does my diamond have a hardware problem?
adempozhari said:
hi
i have a diamond that when i connect to the USB cable ,it ask me normaly to chose betwen Activesync and mass storage but whatever i chose nothing happens on my pc and diamond itself.
my pc and my cable are ok because i can sync my friends diomond noramly.
does my diamond have a hardware problem?
Click to expand...
Click to collapse
Depending on whether you are using Vista or Xp.
Try this: Go to Start>Settings>Connections>USB to PC
> if there is a check mark by "Enable faster data sych.......Remove and see if this fixes your problem.
Secondly, if you flashed your ROM then make sure you remove the previous Device Partnership in your Activesync settings and make a NEW PARTNERSHIP.
Hope this helps!
i have the same problem i connect my phonr to my pc but it wont establisch a activesync connection
I have also the same problem.
When i connect mij Diamond richt below on mij PC sreen see I the message PC can't reconize mij Diamond (tested on more PC's with differnt cables).
If had someone the solution please mail me !
- Diamond with Hard-SPL Olinex 1.93 and the Dutch ROM v2.03.
hi,
i think my diamond has a hardware problem...because it ask me if i want to use activesync or storage when i plug the charger....

brick after tomal 8.7

hello
i have a uni who stuck on bootloader (BL) bl- v2.01
i use tomal 8.7, browsing aplication and find storage manager (some with partition program... ) and my uni was frozen after reboot ... (long story)
i turn (BL) and want to reflash my rom to other version, but my uni don't want it
i run a mtty/putty and want to do a DoC format, but programs don't want to connect with uni, i try a lot of usb cable, usb ports and a 4 computers with Winxp. i use a few version of mtty and uni exit bootloader, hx4700 bootloader...
and dosent works
yy windows not reconize uni show msg unknown device.
some screeens
http://esiu.kom.pl/universal
uni has no sim or sd card.
Hard reset dosen't works
BL keeps serial when i connect it to pc don't turn to "usb" only shows serial
ps. sory for my english
ps2. hmm i think i brick this uni testing storage manager ( option with unmount partiion or something)
ps3. please a sugestion to repair uni
Hello,
I think if you look on HERE the all will be there for you to sort out your problem
Regards
Jay
hmm ive read many times universal wiki and i dont find there a solution.
i think when i "using" storage aplication in tomal 8,7 i delete a partition then it "stuck"
uni in bl mode when plug usb cable don't change to "usb" stuck on "Serial"
if usb cable is pluged in when i turn bl mode when "usb" shows but dosent react with pc ... don't recognize it, active sync have unmarked 'usb connections'
Do you have your SD card and Sim card out of the PDA??
If you cannot see
Serial changing to USB on your device, I say your USB port is damaged and that prevents you from flashing any ROM or device being recognised by PC.
hmm so my port in uni is dameged? ok its software damage or hardware damage ? 10 minutes before uni was stuck i change rom few times.

Dead in bootloader !

Hi, my univversal is dead in bootloader at serial mode and when I connect it to my PC with usb cable it recognize it as an Unknown devices and my phone still stand in serial mode!
I was trried all the method I found like:
I went to device manager of my PC an re-install my usb--didnt work
shut down usb and active synch (with task manager) and ry mtty program-- dident work
I change my usb cable and change te mini usb gate of my phone!-- didnt work
Plz help me!!!!!!!!
god_love_power said:
Hi, my univversal is dead in bootloader at serial mode and when I connect it to my PC with usb cable it recognize it as an Unknown devices and my phone still stand in serial mode!
I was trried all the method I found like:
I went to device manager of my PC an re-install my usb--didnt work
shut down usb and active synch (with task manager) and ry mtty program-- dident work
I change my usb cable and change te mini usb gate of my phone!-- didnt work
Plz help me!!!!!!!!
Click to expand...
Click to collapse
Hi welcome to the forum.... try following
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
(try method 2)
and try to change the computer usb ports...try different usb ports of the computer and try flashing to tomals 8.5 or 8.7 ...
Cheers
Rajiv
Thank you rajivshahi for your answer and attention.
I had try all the methods that I find in hole of internet!!
also I tried your suggstted method. I was connect my phone with ans without SIM and memory to each USB port of my (and another) PCs, I changed my USB cable for several times, I also tried Uni_bootloader program and MTTY but they didn't work (because there is no USB connetion with my UNI and my PC)
I just keep crying!!!!!!
Have you tested doing Doc format?
Hope it helps,
If the device is not recognised by PC at the same time as Serial not changing to USB, I would think your USB port is no longer attached as it should and can cause the problem you described. From time to time USB port might still feel and look secure on mainboard, it will even charge the device, however, when it comes to AS and USB connection to PC, it will not connect properly.
That, or your PC USB or motherboard are malfunctioning. Try other USB devices in the same ports.
My PC's USB ports are work properly because as you told enigma1nz, I had test them with another devices
For the DOC format method: there is no USB port for connecting with MTTY!
Soooooo amazing!
(thanks for all your answers)
So, it means there is no way for me
hey,
have you disabled (unckeck) USB connection for ActiveSync/WMDC at PC?
do it now or USB port will not be available for mtty.
also please make sure that you installed XP sync driver under vista incase you're trying from vista.
follow the same -
1. unckeck USB connection for as/wmdc at pc
2. reset the device by pressing reset button
3. set bl mode (if not there already)
4. connect usb cable
5. start mtty ...
Hi Tomal, first I have to say: Thank you for your amazing roms. they are so fast, nice and stable. I'm one of the biiiig fan of your roms.
seconed: yes I was disabled the USB connection and also kill ir from task manager. but my Uni is still deeaaaaaaad
somehow I have a feeling that something is wrong with the usb port in device. may be connection is broken or something...
Hi everyone,
finally I had to send my Universal to doctor! , he says that I can load your device from SD card, and boot up it, (flashing card)
!!
I was wondered! what is flashing card! (load from SD card without any PC!)
Do any one have some information about this method!!!!
enigma1nz said:
If the device is not recognised by PC at the same time as Serial not changing to USB, I would think your USB port is no longer attached as it should and can cause the problem you described.
Click to expand...
Click to collapse
tomal said:
somehow I have a feeling that something is wrong with the usb port in device. may be connection is broken or something...
Click to expand...
Click to collapse
Yep, it does look like your device's USB being a culprit.
god_love_power said:
Hi everyone,
finally I had to send my Universal to doctor! , he says that I can load your device from SD card, and boot up it, (flashing card)
!!
I was wondered! what is flashing card! (load from SD card without any PC!)
Do any one have some information about this method!!!!
Click to expand...
Click to collapse
I believe this is the thread you are looking for
http://forum.xda-developers.com/showthread.php?t=393370
Thanks a lot enigma1nz, i think that i need but can you (or any one) explane it, step by setp for me PLEASEE !:
1. Download the tool and unrar somewhere in your pc.
2. Decode the rom image (nk.nbf) using HTC64 tool and put it (nk.nba) under the "SD_Flash" directory.
3. Run the "SDFlash_G3.cmd" and follow instruction on the screen.
SD_Flash?????
Decode the rom image (nk.nbf)???????!!
this method is for 3G, my device is 4G
This is the solution
god_love_power said:
this method is for 3G, my device is 4G
Click to expand...
Click to collapse
my dear frnd few days back i was also suffered from that problem...
And problem was with mini usb in universal.
it was disconnected with there tracks from inside.
So just open ur g4 device and resold mini usb.
trust me this is the problem.
Thanks yuvraj, how can I do it? Is there any manual for it?
can you help
You can find the manual in the Wiki, just do a search
I could'nt creat golden disk (flash from sd) cos that is for G3 devices, I just think that can we install another OS like linux on SD that is boot himself up?!
or i just have to change my universal mainboard!!!!?
Finally I beleve that my Uni is dead and I have to say goodbye to it
I'm going to buy HTC Advantage X7510, but there is one question:
Can I upgrade its WM 6.1 to 6.5 ?

Computer cant recognize my Diamon

Dear Sirs;
Maybe this part of forum not be the proper place for my question but I don't know the poeple more expert than XDA masters.
Since last monday, computer cant recognize my Diamond when I connect it by USB cable and "USB device not recognized" appears. I will be really appreciated if you kindly help me.
Best Regards
Dariush Chegini
Try reinstalling Active Sync/Windows Mobile Device Center.
First remove Active Sync/ WMDC, restart PC and than install Active Sync/ WMDC.
Thanks for your kind attention. I reinstalled Activesync...no change, computer can't recognize the Diamond. My Diamond charges with both charger and computer, USB headphone works but PC can't recognize it....
I'm so confused and will be really appreciated if XDA masters help me.
Best Regards
XP or Vista or Windows 7 or which OS?
I've tried by both WIN XP and Vista.
could be a few possibilities for XP atleast...
activesync - file->connection settings->allow usb connections checked
faulty cable, try another one
faulty port on computer, try another one
driver issue - a difficult one...
i had this on my xp, found out there's something wrong with the cable - phone charging fine via computer USB, but XP says it doesn't recognize the device so doesn't connect to activesync....
good luck
Try on your Diamond -
Start>Settings>USB to PC
Unchek "Enable faster data synchronization"
If none of the above solutions work, maybe a hard reset...
I tried another cables, all options in "USB to PC", Activesync options, hardreset, even install other ROM but PC still can't recognize the Diamond.
It seems to be a Hardware problem but Diamond can be charged by USB and USB headphone works properly... I'm so confused .
Thanks Millions
Dariush
dchegini said:
I tried another cables, all options in "USB to PC", Activesync options, hardreset, even install other ROM but PC still can't recognize the Diamond.
It seems to be a Hardware problem but Diamond can be charged by USB and USB headphone works properly... I'm so confused .
Thanks Millions
Dariush
Click to expand...
Click to collapse
Try this in order...
1. Connect diamond to pc - it should at least charge as your say, but not detect Activsync
2. Goto Settings > Connections > USB to PC
3. Check Allow USB Connections > Uncheck allow fast data sync...
Does it connect?
if not and if you are using Vista
1. goto Windows Mobile device Center
2. check the attached image to see you have the same settings...
Does it connect?
if still not, then it could be driver issues, which I can suggest, once you reply to the above...
Thanx for your attentions. I've tried uncheking the said bottom but no change.
I used to connect the Diamond to the same notebook without any problem for more than 16 months, but the damn notebook stop recognizing my Diamond these days .
Thanks Millions
Dariush
may be usb port on your computer is malfunction. Did u try different usb port?
You need to open device manager in control panel to see how you diamond is listed.
Ever since i started with a new company 3 years ago they have some software that prevents activesync from connecting to any device I have from their computers using USB.
I went Bluetooth method and all is fine. I just use the USB for large, direct file transfer to internal storage.
If you get issues with activesync and usb and can take ages to resolve (if possible).
I guy's.
After a lot of search in this forum and a lot of other forum's, i came to this threat.
I had the same problem, my diamond didn't connect to my pc.
I had tried all the different suggestion, and nothing seemed to work. until i read the post of cloudedhopes, that suggested to change the usb cable. Because it was the only thing that i hadn't tried, i did change the cable, and it worked!
So i'm posting only to thank you guy's for all of the help, given not directly to me, but to all user!

Categories

Resources