Develop Bugs

Urgent Hellp is needed

My Pda 2k device i tryed to upgrade it from 2003 SE to 2k5 after pressing update the device restarted gived me a gray screen and typed on it seril and at the buttom v2.02 now i cant open the device each time i reset or heard rest this is the only screen appears to me i cant even connect to activsync please i need your help what to do to get my device back, this error message i recived (usb device not recognized aslo active sync didnt recognize it)
i need to add a point the device is not working on the USP connection as it have a problem only serial port to connect with the pc
i'm so new here please help me

not to worry.. you can perform a hard reset of your 2k3 version "power+reset" to get you back to at least a working device.. I have been through this and have had this happen to me as well.. try entering bootloader again "power+record+reset" and dock it fairly quickly and it should change to USB on the screen and PC recognize it... also for anyone reading this.. I would highly recommend plugging your cradle into a 5v power supply as I can only imagine most of the bricked BAs are probably due to a computer freezing and/or the PC shutting down power to the USB port only for a fraction of a second and hosing the flash up.

THx Man i will try i hop this will work :lol:

USB Device Not Recognised on Bootloader

I have a problem. My Exec is stuck on the bootloader screen. All I see is Serial at the top, and v1.00 at the bottom.
When I connect my exec via USB, the screen continues to say Serial (rather than switching to USB) and the PC I connect to 'installs' the device as 'unknown device' in device manager.
I've seen mention of the problem elsewhere on the site, but the only solution I can find seems to be to keep trying, and eventually it's recognised. So far, after three days of trying, it has not been recognised.
I am aware of Buzz tool to get the device out of bootloader mode, but that required a connection to be established, which at the moment, I can't do.
Has anyone got any experience of this, or any ideas as to what's causing this, or how this can be fixed? I have tried uninstalling the 'unknown device' from device manger, restarting the PC (and hard reset of the Exec) then reconnecting, but the same thing happens every time.
Any ideas would be appreciated, as I'm currently staring at a rather expensive paper weight.

Try this it shld work
hdubli said:
This is based on my experience with two UNis..one Exec and other JASJAR..both had same problem...this is how I solved :
-Put yr device in bootloader Mode
-Disable USB in Active Sync
-Now connect woth USB cable and open mtty utility
-Select the "WESUSB... " port
-You shall see a blank white screen..press Enter to get "USB>"
-Then type ( as BUzz has informed) set 14 0
(here I wud like to inform that after doing the above I did not get success so I typed set 14 10,then set 14 9 for two three times)
-Then I ran the ROM Upgrade directly(After enbabling the USB)
-I then followed the procedure as informed on the COngratulations Screen that is hold the two "-" buttons and soft reset and then pressed 0
-I got them back to normal..
I hope this helps to all my friends...Pls feel free..pls do not trouble our Buzz..he might be busy in inventing something more to our devices
Click to expand...
Click to collapse

Guru Meditation said:
I have a problem. My Exec is stuck on the bootloader screen. All I see is Serial at the top, and v1.00 at the bottom.
When I connect my exec via USB, the screen continues to say Serial (rather than switching to USB) and the PC I connect to 'installs' the device as 'unknown device' in device manager.
I've seen mention of the problem elsewhere on the site, but the only solution I can find seems to be to keep trying, and eventually it's recognised. So far, after three days of trying, it has not been recognised.
I am aware of Buzz tool to get the device out of bootloader mode, but that required a connection to be established, which at the moment, I can't do.
Has anyone got any experience of this, or any ideas as to what's causing this, or how this can be fixed? I have tried uninstalling the 'unknown device' from device manger, restarting the PC (and hard reset of the Exec) then reconnecting, but the same thing happens every time.
Just noticed your user name, I was a big Amiga fan a few years back, still fire up Amiga forever occasionally on my PC when I feel the need.
Any ideas would be appreciated, as I'm currently staring at a rather expensive paper weight.
Click to expand...
Click to collapse
Try it with a different USB cable or in a different USB port (don't go through a hub and if you've been using a laptop then try it on a desktop PC since some laptops have hubs built into them). If that doesn't work then you're out of luck as your Universal isn't detecting that you've connected to your PC and its time to send it in for repair.

Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?

i am stuck on the same problem and wondering the forum for almost 3 days now with no luck.... please help my device is in boot loader mood but not turning the serial to USB ......... please HELP.......

solution
Guru Meditation said:
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
Click to expand...
Click to collapse
Please follow the steps:
1. Plug in ur usb cable in bootloader mode while it is showing 'serial' and version 'x.xx'.
2. Soft reset by pressing Backlight+power+reset pin WHILE KEEPING THE USB CABLE CONNECTED
3. your phone will now reboot into 'usb' mode. Don't remove the usb cable yet.
4. Remove the Memory card while keeping the usb cable still connected and VOILA,your pc starts recognising your phone as Microsoft usb sync.
5. Do whatever you want to do now (upgrade)
Hope it solves the problem now.
Press thanks if it does.

Something else to try
Having had a few issues with my G3 Uni, I've been through my fare share of Uni bootloader issues. When I find that I can't get the 'serial' to go to 'USB', I normally find it's because I haven't taken the memory card or the SIM card out (usually the memory card).
Make sure your memory card is out, then try to enter the bootloader and see if this cures it. If it does, then use mtty and the command 'set 14 0'
This tells it to reboot on reset. if you were to use 'set 14 1' it would go back to the bootloader on reset.

my Htc hd2 t-mobile won't recognize usb on boot-loader mode
hey guys i have a big problem!!!! my Htc hd2 t-mobile won't recognize usb on boot-loader mode. Here is the story my phone was running android 2.3.7 cyanogen 7 but i wanted to update it to ics android 4.0.4, So to do that i restarted my phone while holding down the down volume button and the boot-loader with the three colors came-on saying serial but when i connect my usb cable it won't show usb. even when i tried to run the dft.exe it shows an error saying usb connection failed. BY the way it lets me access the sd card using the usb cable on my pc, so i don't know what the problem is. PLEAS HEALP i am begging u guys pleas!!!!!!!!!!!!!!

kaleb2954 said:
hey guys i have a big problem!!!! my Htc hd2 t-mobile won't recognize usb on boot-loader mode. Here is the story my phone was running android 2.3.7 cyanogen 7 but i wanted to update it to ics android 4.0.4, So to do that i restarted my phone while holding down the down volume button and the boot-loader with the three colors came-on saying serial but when i connect my usb cable it won't show usb. even when i tried to run the dft.exe it shows an error saying usb connection failed. BY the way it lets me access the sd card using the usb cable on my pc, so i don't know what the problem is. PLEAS HEALP i am begging u guys pleas!!!!!!!!!!!!!!
Click to expand...
Click to collapse
you have the wrong forum friends! This Htc Universal section
to update Android on HTC HD2, you can use the Clock Work Mod Recovery !! for more details should refer to this thread http://forum.xda-developers.com/showthread.php?t=1021837

I-MATE JASJAR hung
Guru Meditation said:
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
Click to expand...
Click to collapse
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me

bechir2013 said:
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me
Click to expand...
Click to collapse
look here
http://forum.xda-developers.com/showpost.php?p=5456317&postcount=6
the first point...

A lot easier than to root this device

i780 usb and activesync problem

Hello!
First, sorry my bad english
I have bought my samsung i780 just for a week. I would like to connect it to my laptop to update the contacts and save the pictures. I installed the ms activesync 4.5 and plugged in the data cable (type: APCBS10BBE and also tried APCBS10UGE). The windows sent me an error message about could not recognise the phone. I have not installed any specific usb driver. I tried plug in and out the cable more times (about 10-15) and once there was a success, the synchronisation was fine. Everytime when i try to connect, i have to repeat the plug in/out procedure about 10-15 times... I am afraid, this is the i780 usb connectors fault Is there any other possibility to fix the problem whithout change the connector?
Could you be so kind to give me some advices?
Thanks
TSanya

Try getting a Bluetooth USB Pen...

Thanks, but i've already tried the bluetooth for connetcting to the activesync. The problem is: I can't set up the bluetooth serial port on the i780 to the same as the pc bt serial...

i have this same problem :/ i made hard reset and after it i cant connect :/

having same problem with my i780 I am at a loss, phone is in dutch and I can not load english rom with out usb connection, what should I do?

I had the same problem，but I have fixed it.
I got a i780 with CoinJun's Rom which version was forgot.I often can not sync to my pc.I upgraded the new ROM which version is PDXIB1 downloaded from samsung.Now,it is ok.

i have a big problem. i have a samsung i780 with orange rom (pbvic2), he wont connect to activesync, when i put the cable usb in, he charge, red led is on, the pc make sound connection, on the phone appears "connecting to host" but nothing. And another problem is that he see the sd card, but the computer wont, i try another card, the card reader is seeing , after i put him in the phone he become invisible on the pc, he corrupte them, pls tell what to do, or maybe i need to change the rom? but how ? becausae i have no pc connection...
sorry for my english

Dead in bootloader !

Hi, my univversal is dead in bootloader at serial mode and when I connect it to my PC with usb cable it recognize it as an Unknown devices and my phone still stand in serial mode!
I was trried all the method I found like:
I went to device manager of my PC an re-install my usb--didnt work
shut down usb and active synch (with task manager) and ry mtty program-- dident work
I change my usb cable and change te mini usb gate of my phone!-- didnt work
Plz help me!!!!!!!!

god_love_power said:
Hi, my univversal is dead in bootloader at serial mode and when I connect it to my PC with usb cable it recognize it as an Unknown devices and my phone still stand in serial mode!
I was trried all the method I found like:
I went to device manager of my PC an re-install my usb--didnt work
shut down usb and active synch (with task manager) and ry mtty program-- dident work
I change my usb cable and change te mini usb gate of my phone!-- didnt work
Plz help me!!!!!!!!
Click to expand...
Click to collapse
Hi welcome to the forum.... try following
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
(try method 2)
and try to change the computer usb ports...try different usb ports of the computer and try flashing to tomals 8.5 or 8.7 ...
Cheers
Rajiv

Thank you rajivshahi for your answer and attention.
I had try all the methods that I find in hole of internet!!
also I tried your suggstted method. I was connect my phone with ans without SIM and memory to each USB port of my (and another) PCs, I changed my USB cable for several times, I also tried Uni_bootloader program and MTTY but they didn't work (because there is no USB connetion with my UNI and my PC)
I just keep crying!!!!!!

Have you tested doing Doc format?
Hope it helps,

If the device is not recognised by PC at the same time as Serial not changing to USB, I would think your USB port is no longer attached as it should and can cause the problem you described. From time to time USB port might still feel and look secure on mainboard, it will even charge the device, however, when it comes to AS and USB connection to PC, it will not connect properly.
That, or your PC USB or motherboard are malfunctioning. Try other USB devices in the same ports.

My PC's USB ports are work properly because as you told enigma1nz, I had test them with another devices
For the DOC format method: there is no USB port for connecting with MTTY!
Soooooo amazing!
(thanks for all your answers)

So, it means there is no way for me

hey,
have you disabled (unckeck) USB connection for ActiveSync/WMDC at PC?
do it now or USB port will not be available for mtty.
also please make sure that you installed XP sync driver under vista incase you're trying from vista.
follow the same -
1. unckeck USB connection for as/wmdc at pc
2. reset the device by pressing reset button
3. set bl mode (if not there already)
4. connect usb cable
5. start mtty ...

Hi Tomal, first I have to say: Thank you for your amazing roms. they are so fast, nice and stable. I'm one of the biiiig fan of your roms.
seconed: yes I was disabled the USB connection and also kill ir from task manager. but my Uni is still deeaaaaaaad

somehow I have a feeling that something is wrong with the usb port in device. may be connection is broken or something...

Hi everyone,
finally I had to send my Universal to doctor! , he says that I can load your device from SD card, and boot up it, (flashing card)
!!
I was wondered! what is flashing card! (load from SD card without any PC!)
Do any one have some information about this method!!!!

enigma1nz said:
If the device is not recognised by PC at the same time as Serial not changing to USB, I would think your USB port is no longer attached as it should and can cause the problem you described.
Click to expand...
Click to collapse
tomal said:
somehow I have a feeling that something is wrong with the usb port in device. may be connection is broken or something...
Click to expand...
Click to collapse
Yep, it does look like your device's USB being a culprit.

god_love_power said:
Hi everyone,
finally I had to send my Universal to doctor! , he says that I can load your device from SD card, and boot up it, (flashing card)
!!
I was wondered! what is flashing card! (load from SD card without any PC!)
Do any one have some information about this method!!!!
Click to expand...
Click to collapse
I believe this is the thread you are looking for
http://forum.xda-developers.com/showthread.php?t=393370

Thanks a lot enigma1nz, i think that i need but can you (or any one) explane it, step by setp for me PLEASEE !:
1. Download the tool and unrar somewhere in your pc.
2. Decode the rom image (nk.nbf) using HTC64 tool and put it (nk.nba) under the "SD_Flash" directory.
3. Run the "SDFlash_G3.cmd" and follow instruction on the screen.
SD_Flash?????
Decode the rom image (nk.nbf)???????!!

this method is for 3G, my device is 4G

This is the solution
god_love_power said:
this method is for 3G, my device is 4G
Click to expand...
Click to collapse
my dear frnd few days back i was also suffered from that problem...
And problem was with mini usb in universal.
it was disconnected with there tracks from inside.
So just open ur g4 device and resold mini usb.
trust me this is the problem.

Thanks yuvraj, how can I do it? Is there any manual for it?
can you help

You can find the manual in the Wiki, just do a search

I could'nt creat golden disk (flash from sd) cos that is for G3 devices, I just think that can we install another OS like linux on SD that is boot himself up?!
or i just have to change my universal mainboard!!!!?

Finally I beleve that my Uni is dead and I have to say goodbye to it
I'm going to buy HTC Advantage X7510, but there is one question:
Can I upgrade its WM 6.1 to 6.5 ?

P3300 can't connect with USB

Hi guys, sorry for my bad english.
Since today can't sinchronize my ppc with wm 5.0.
Here's the problem: when I pug it with usb cable, nothing happens.The orange light is on, the phone is in charge but nothing happens.Usually when I connect the phone I can see windows looking for ip address, and the activesynch shows... but this is not going to happening anymore.
I tried to reistall activesinch, I've cleaned the registry and i tried to connect it with others software.Still nothing.
Firewall is disabled.Any solutions?
Thank you in advance.

Zealot87 said:
Here's the problem: when I pug it with usb cable, nothing happens.The orange light is on, the phone is in charge but nothing happens.Usually when I connect the phone I can see windows looking for ip address, and the activesynch shows... but this is not going to happening anymore.
Click to expand...
Click to collapse
I had the same problem sometime ago. I've changed the wire first but nothing happened. My speaker, my Mic was dead and I could switch on FMRadio without the Hands-free!!!
What I did...??? I updated my mobile's Radio with 3.39.90 Version. How can you do this without active sync???
1. Remove SIM Card and Storage Card from the Mobile.
2. Press and Hold the Right Button (Recording Button) and Press together the Power Button. You will be in the Bootloader Screen. Try to update the Radio first.
3. Check it if it's working ok.
2nd way...
1. Copy the official ROM of WindowsMobile to the Storage Card.
2. Press Right Button (you know the Voice Rec) and holding that press the Power Button...
the mobile will be bootloader mode and will try to install the official ROM from the Storage Card...
wait a bit and then when it finish, check it if it is working properly!
Hope to help... waiting to "hear" sorry, to read good news

I have the same problem i cant sincronize the pda whith the activesync and i wish to change the rom. Now it's in france and i wish to change it to english, and it's locked to orange france i think. What can i make? It starts in bootloader, but the instalation from the card is not starting. thankx
le. and if i want to install something gives error 260

I had the same problem 1 month back, checked the mini usb data cable with a multimeter just to find that one of the data TX/RX wire was short with +5v wire, cable was faulty. the 1st and the last wires (+5v , -5v) were ok thats why it was charging the phone, but not connecting to pc, it was giving error unrecognised usb device.
u can also check for bent contacts at the USB mini connector on ur phone.

strange
hy guys
i´ve got a strange problem with my arte110.
for some reason i cant establish an activesync-connection,a few days ago i had some wm6.5 rom running and couldnt connect my device, then suddenly today (maybe because i reinstalled windows on my computer yesterday, i dont know) i was able to connect the phone while in bootloader... so i flashed happy and lucky the original wm (os 5.2.1620 build 18125.0.4.2) rom i got from t-mobile austria.
now its the same problem as before, i cant connect my device, i've restartet artemis and my computer several times, i've reinstalled activesync 4.5 a million times, i've tried all available usb-ports- different usb cables (same cable works with external harddrives) and even my office-computer, and so on...
my pda is (and was allways) charging but i cant syncronize.
has anyone any idea what could cause this problem?- please don't tell me the usb port of the pda is damaged, I wouldn't want to have to fix anything in this case...
hoping for good news, McPerfuntory
[by the way, please dont judge me for spelling mistakes, i'm from austria!!!]

done
okay guys, no need to respond anymore, i got it right..
but i don't really know how i repaired that one, i disassembled the devive cleaned everthing in there and cleaned the usb connector..
..works again