Problem with hTC S620!! - Upgrading, Modifying and Unlocking

Dear All !! Dear Pof!
I am trying to unlock hTC S620 ,but with no luck!!
when i connect the phone with Active Sync with the softwear and press AUTO_Unlock_v3a it showing me direct the message :
SoftSPL error
Erorr
Insufficient trustlevel.
You need to application unlock your device (or singn executable with privileged cert)
even i did try to past the file SSPL in phone and open it ,it gona say to me the same erorr !!
Please what is this problem is ?
and another think :how can i make hardwear Reset to this model hTC S620? ther is no hole place to press For reset ,could u show me please how to do it .
i am very sad becouse i spend over 5 hours trying to unlock this funny phone!!!
please help!!
Thanks.

Related

my ARTEMIS is blocked "BRICK" please help

I updated my rom from the original spanish version to a Artemis_Touch_3.01
After some use, the device is blocked.
It starts the HArd reset, after "Format messages" It starts HTC white screen
IPL 3.13.0001
SPL 3.13.0000
and nothing more
.
It also works ROM update mode (Three colors screen) but when I execute the Rom update frommy pc, it reaches 2/3% and gives different Errors depending the ROM,
"Ivalid Vender ID [294] when I use the ROM HTC_P3300_SPA_3.13.412.1_4.1.13.44_02.94.90_Ship_R
ERROR [270]: Update Error -The Image File is corrupted - When I use Black & Blue 4.3 or Artemis_Touch_3.01
I need help!!!
brick?
hello,
First you must open the bootloader menu,
hold voice dial button and press soft reset.
If this not working hold voice dial and on/off button and softreset.
You must connect first your htc with your pc and the start the bootloader.
When you are in the bootloader menu, you can upload an orginal fabricrom to your htc.
Search xda-developer for the fabric rom.
And then you can change your rom for something else but don't forget the uspl.
When you want to change image you must install the uspl first otherwise everthing will blocked
the problem you have is that you have to run the uspl first before you can flash another firmware. If you run the uspl you will see that the spl loader of your device is version 1.11.000 and than you can flash an other rom of your choice
greetzz Patrick
uspl does not work. this is the point you can not get it.
have a problem but I cannot find anything useful for my case, maybe you can help me?
pvdhelm said:
the problem you have is that you have to run the uspl first before you can flash another firmware. If you run the uspl you will see that the spl loader of your device is version 1.11.000 and than you can flash an other rom of your choice
greetzz Patrick
Click to expand...
Click to collapse
Hi Patrick,
I have a dutch rom on my htc P3300
IPL: 1.12.0001
SPL: 1.12.0000
GSM: 02.67.90
os: 1.12.0.0
my HTC remains stuck on the startup screen (logo HTC) and will not get any further.
Connection with active synch is not possible, ans holding the buttons reset-voice rec-on/off buttons don't react. WM cannot be started in that way.
is it possible to find a boot program which allows me to start up WM again like a regular PC? something like a emergency startup disk? I have a 2GB micro SD card. After reading and trying so many things, I lost the way in this site and was hoping maybe you can send me some useful links that can solve my problem? I would appriciate the effort.I don't know if it's allowed to send my personal emailadress? If it is allowed please let me know. Maybe we can exchange directly some info, otherwise I don't have a problem mailing this site.
(I hope I can find this thread again after closing?)
Kind regards , Eli
my artemis is also in the same state
Hi All,
Please help me with problem which I am facing with my HTC P3300
When i switch it on..Its stuck in the state where it shows
IPL 3.07.0001
SPL 1.11.0000
GSM 03.08.90
OS 3.4.0.0
What I tried.
1. I tried USPL , its not loading as device is not getting detected in my laptop.
2. Volume Down+Reset is not working
Please help me with this

My QTEK 9000 IS DEAD, PLSSSSS HELP ME

Hello,
I connect my qtek with pc. I tried to install wwe rom - from german to english. I ws downloaded english rom but cant install coz i have problem with COUNTRY ERROR -ERROR 120 atfer that i install in qtek "MaUpgradeUt_noID".exe and after that my qtek go to hell.
when i done hard reset on the screen write only: Serial and v1.00!!!!
..............qtek is dead...................
PLzzzz people help meeeeeeeeee
what can i do now for repair my qtek?????
p.s. srry for my bad english
Kind regards
Your Uni still alive
Try to download "Exit Bootloader.exe" from wiki, conect the uni to USB and Run the applcation...
If you uni is death when the Bootloader is lost. I brick my Jasjar when the Bootloader was gone, dont worry Try to read more in the forum Universal WM6.
AIN1 said:
Try to download "Exit Bootloader.exe" from wiki, conect the uni to USB and Run the applcation...
If you uni is death when the Bootloader is lost. I brick my Jasjar when the Bootloader was gone, dont worry Try to read more in the forum Universal WM6.
Click to expand...
Click to collapse
Hi AIN,
Thnks Mucho Mucho!
My Problem is, that i can only choose Com 1 to Com 3 in mtty 1.42 - Because of this i can't use the methode which is explained. - What i am making wrong? - I use a Sony Vaio Laptop for booting...
Thanks a lot!
if you have the rom try tis out!
1.unzip the file!
2.put the rom-extended rom-radio(or whatever you need!) in this folder
3.when you'll connect the phone on the usb,on the screen you have to see "usb v1.01".
4.run the "MaUpgradeUt_noID.exe"
5.wait till it will finish flashing!!
6.enjoy the new rom!!
qtek pu10 0r 9000 is freeze please big help
please big help / i just try to change language on my qtek 9000 and when the phone finish. and the screen freeze. and i off it and on it .and still the display show but freezing. and it can't connect to the active sync and pc /please help
Try a soft-reset first.
If not, you may have to hard-reset. You will lose all your data and programs you've installed and it will revert to factory state (or last flashed ROM).

Magician - No Gsm Problem

Hello, i recently tryed to flash a new rom on my magician and when i was flashing it the magician went down ( discovered later that i didnt fully charged the battery ... i know ... im a noob ) , now appears "No Gsm" when i turn on the pda. I can go to windows i can flash Rom + Extrom, i cant upgrade via sdflash it gives me an error " Not Allowed " what is this ? I've tryed several commands in console but no sucess. Can this be fixed whiout jtag way ? Please help me out. Regards
Can any1 help me out ?

help me fast please my artemis uspl failed

My artemis is in the white screen.after use the Artemis_USPL (in ROMUpdateUtility level).
please help me fast.please.
...
sounds like it went wrong.lol
you probably bricked device..
take sd card out, if device goes to bootloader - red,blue,green..
there is a chance to bring it back to life.
to do this you need the official rom that was on the phone, so first things first, download that!
secondly, download ''uspl cmon'' this will let you flash more roms to your device, - with old uspl it sometimes stops at 3% because of size.. but with cmon, it doesnt!
so flash with official rom, uspl cmon, then flash a new 6.1 or 6.5 rom!
good luck..
if you need more help, message me..
...
...try this beforeyou panic..
try uspl again, once dos screen has finished, (penguin) soft reset and update uspl. device should restart and spl should be
1.11.0000 - uspl
1.11.cmon - uspl cmon!
help please,
need the original t-mobile Mda Compact Rom!!!
can`t flash other roms.
when i want to flash it shows me the error 300
i just need the original rom.
i can`t do nothing with my device!
please help me
raving_nanza said:
sounds like it went wrong.lol
you probably bricked device..
take sd card out, if device goes to bootloader - red,blue,green..
there is a chance to bring it back to life.
to do this you need the official rom that was on the phone, so first things first, download that!
secondly, download ''uspl cmon'' this will let you flash more roms to your device, - with old uspl it sometimes stops at 3% because of size.. but with cmon, it doesnt!
so flash with official rom, uspl cmon, then flash a new 6.1 or 6.5 rom!
good luck..
if you need more help, message me..
Click to expand...
Click to collapse
hi my friend .
im tryed but cant do it. when i run start_uspl it go to boot loader and occur error 260 and ... !
what is the problem ?
what i can do ?
please help me !
thank's a lot .
error 260 Here after I get to bootloader
No any one ? !
help me please !
...
error 260 is the connection to activesync dude..
you just gotta keep trying..
(remember do not soft reset)
Take SD card out and try again.
...
solved??..
raving_nanza said:
solved??..
Click to expand...
Click to collapse
no !
after start and finish artemis-uspl my artemis stay in white screen & the ROMUpdateUtility failed ! (error 260 !)
my pc windows is 7 !
excuse me for bad english write ! bacause my language is other !
tnx
...
wait for artemis to get active sync connection before continuing with the RUU..
(make sure to take memory card out)
raving_nanza said:
wait for artemis to get active sync connection before continuing with the RUU..
(make sure to take memory card out)
Click to expand...
Click to collapse
im sure my artemis connected to WMDC in win 7 !
and the SD Card is out !
after start artemis-uspl and finish my artemis(p-3350) stay in white screen ! and when the ROMUpdateUtility started(auto) in verifying information level occur 260 error !
...
after the white screen device restarts, thats when you click through the RUU
...
(let active sync gain connection before clicking through RUU)
raving_nanza said:
(let active sync gain connection before clicking through RUU)
Click to expand...
Click to collapse
in start_uspl.exe in 70% level my artemis stand in white screen & ..... 100% !
im sure when my artemis in white screen its conncted to pc !
can i run ROMUpdateUtility after white screen in bootloader or when the window are booted ? ( Manual)
Hello! I've got a big problem with my htc p 3300. It Doesn't start. What can I do? please help me
ovidiumihai said:
Hello! I've got a big problem with my htc p 3300. It Doesn't start. What can I do? please help me
Click to expand...
Click to collapse
download your original rom
what are the red numbers and letters when the device starts up?
so let me get this straight
I hard reset my default ROM
I install
- Cert_SPCS
- EnableRapi
activesync ON
start uspl (Dos)
wait for it
(Penguin)
Creating Preloader 1:1 Mapping
WHITE SCREEN & no active sync connection
How long do I wait here, before I am able to do anything? I can safely reboot however ^_^ and it goes back to WM5, like nothing happened
my device is an old Dopod P800W, never flashed before and running old ROM from 2006
Worked a treat, saved my bacon.
Many thanks

Artemis Loadboot

hi, everyone, i have one artemis but this pda doesn't pass the load boot window, i have try the hard reset and it won't pass for windows... so, i can't syncronise the phone with pc to put a new rom, plz help!!
soft restart , when the screne is out ...then press power&voice button at the same time,
then u can see three colour ....after that insert u usb cable..... now u can flash your PDA....GOOD LUCK.
dear friend, the three colour menu apears and the pc recognize the pda, but in the RUU instaler, apear error code #260 (update error).
i try the artemis USPL to free the CID...
with Shady 313 ROM, the error is #260 (file open).
plzzzz with my diamond this process is very easy :S i'm broken my head with this pda model
SOLVED tks

Categories

Resources