Hello, i recently tryed to flash a new rom on my magician and when i was flashing it the magician went down ( discovered later that i didnt fully charged the battery ... i know ... im a noob ) , now appears "No Gsm" when i turn on the pda. I can go to windows i can flash Rom + Extrom, i cant upgrade via sdflash it gives me an error " Not Allowed " what is this ? I've tryed several commands in console but no sucess. Can this be fixed whiout jtag way ? Please help me out. Regards
Can any1 help me out ?
Related
:roll:
i reaaly feel depressed .. & that is coz when i was tring to upgrade my T_Mobile Radio to RU 6.24.00
that i downLoaded from http://www.romanweb.com/yorch/
my mobile gave me the messge of that the upgrade failed ...
keeping repeating restarting ..upgrading process progress for several times ...then i ting i did restart or something like that after that I think my device Died no longer working all what i could see is T)mobile start screen with the ROM vervion RT Lower Courner U above it & some letter above them without vervions #s!!! !!!.
I did reset+ON/OFF Botton pressing ... got into the WALLBAY Bootloader V5.15. then .............................. WAIT...
then i resseved the messege GSM ERROR.
I restarted same as before +on/off .
Recieved same message then Pressed RT Upper Botton got into FLASH TOOLS selected GSM ROM TO SD got the messege
SD Backup
==============
Please
connect rs232
and run PC Monitor
Now
in your sitle this messege is followed by
SD BACKUP
=============
Please
connect rs232
and run
PC Monitor
Now
We're not yet sure how to use this to dump the GSM ROM.
..... End.
Now ,,, what sould i do to recover my T-Mobile ....
GSM Error, 1% failed, and battery not charge
That was what happen on my XDA too. I've been upgrade, downgrade both OS and RS roms with my XDA for about 9 mos without any trouble until last week when I tried to upgrade RS from ATT A20.10 to TMO 6.24.01, the upgrade failed and now I am stuck with 1% failed problem. Worse, the battery is not charged any more causes any further upgrade fail. I still can upgrade/downgrade the OS rom but do not know how to fix the Radio stack.
I have tried virtually all suggestion on this forum: the 4 RS files upgrade, SD nb1, nbf upgrade, repair.zip, Programme A, programme B, different OS and RS roms upgrade/downgrade. None worked.
I even opened the XDA and connected wires. Still not working.
I upgraded...so I thought to this version...
Rom Version 4.01.16 eng
Rom Date 02/04/01
Radio Version 4.21.00
Protocol version 32s54 now I cant get into bootloader, cant use the phone, or internet on my SX-56...nor can I boot by flashing....What Have I done wrong should I just use it as a paper weight? Remeber If I press the power button and soft reset to just goes back to the Tmobile screen an continue to boot as a normal Alt-Ctrl-delete. I have tried xdairt and himayla..cant get it to work...
someone plz guide me through this I want my pda!!!!
Try the option fix-bootloader from the XDATools.
Then you should be able to enter the bootloader, and reflash your device...
HTH
Stefan
after XDA1 ugrade to 4.01.16 not able to do up/downgrade !
Have upgraded my XDA1 to ROM-version 4.01.16 Eng.
Now I wanted to install a different version, but I failed.
The PDA is working so far, but I can't upgrade/downgrade anymore.
When I use OSImageTool, there is a connection error displayed in the black command window:
ERROR: GetConnectionType - An existing connection was forcibly closed by the remote host. error getting connection type.
Can somebody please help me ?
Re: after XDA1 ugrade to 4.01.16 not able to do up/downgrade
Stefan_PDA said:
Have upgraded my XDA1 to ROM-version 4.01.16 Eng.
Now I wanted to install a different version, but I failed.
The PDA is working so far, but I can't upgrade/downgrade anymore.
When I use OSImageTool, there is a connection error displayed in the black command window:
ERROR: GetConnectionType - An existing connection was forcibly closed by the remote host. error getting connection type.
Can somebody please help me ?
Click to expand...
Click to collapse
There are many postings concerning this problem.....
You have to flash via SD-Card....
HTH
Stefan
Cant get into bootloader via pressing pwr botton and soft reset. I've have also hard reset the device and i still get nothing
Have you tried the fix-bootloader option from the xda-Tools?
Stefan
yes...but all i get is tthe command prompt...and i click yes is there something else i must do...tried edit2003 but still nothing
Cannot execute
Cannot execute "C:\DOCUME~1\Ovynten\LOCALS~1\Temp\Rar$EX00.203\RSUpgrade.exe"
wHAT THE [email protected]#$ DOES THIS MEANS? If uI could only understand this maybe I could get mt PDA working again.
could anyone help me out of a mess please , i have recently purchased an mda3 to replace my xda2 , i unlocked the phone which went ok but wouldnt accept my o2 sim , being the same phone as the xda2s i thought maybe it would need the o2 windows version rom on , i selected the wrong rom from my pc and the upgrade stopped after a few seconds stating it was the wrong version but now the phone has no rom on at all just a dark screen with "serial" or "usb" if it is docked . Have i done permanent damage ? any help would be very much appreciated
Your phone is currently in bootloader mode - if you have a valid ROM for your device you should be able to flash it with the phone in the USB cradle (the dark screen should change to USB).
If you don't have a valid ROM, go check out the wiki, there's plenty to choose from there!
many thanks forza , as u can prob guess im new at this !
sorry to be a pain forza but unsure which files on the ftp to use , doesnt have to be the latest rom i just need it to work again , could you also tell me how to execute the files , do they load from the desktop , many thanks bren the amatuer
This page on the wiki lists the available original ROM packages;
http://wiki.xda-developers.com/index.php?pagename=BA_Upgrades
The T-Mobile UK one (1.42) is the latest version ROM (3rd on the list), so I'd recommend you start with that (it's the one I use).
[EDIT] just noticed you're showing as being on O2, further down the list (almost at the bottom of the first section) there's a UK O2 ROM - that may be better for you.
With the phone docked in the cradle (with USB showing on the screen), you can just the run the exe you downloaded and it should flash it for you.
thanks forza ! your a star worked a treat
qtek 9090 with USB V2.06 message error
I have the same problem with my qtek 9090, but I dont can sync my pocket pc. I see only USB V2.06 if the pocket is full charged ( and serial if not on the crable connected ).
Why I can not sync this with my laptop??
I have make a hard reset but still not work!!!
please help me
I have read many post but nothing found...
thank you
scharmander ( newbee )
Hi, I have a xda o2 exec , thats in bootloader mode ( v2.01 )
I have uploaded radio verion 1:15 which went to 100% no problem
but when i try to mount a rom ( and I have tried a few different ones ) it only gets to 9% then stops and returns an error message (the error message is shown in the RUU on the pc )
Any ideas ?
ps i dont know if hard SPL, CID or SIM unlock has been run on it before hand as I recieved the phone like this, just wondering what my next option would be?- pleeeeease help
many thanks to BUZZ LIGHTYEAR for the following thread :
http://buzzdev.net/viewtopic.php?f=40&t=36475
problem solved, storage formatted, 6.5 rom installed ....nice
cheers buzz ...
Hi ,
I was flashing my jasjam using sspl-herm and a 6.1 rom ,
While upgrading the progress bar reached the end but it stayed saying upgrade in progress , it took too longer than normal and i knew it wouldnt continue so i soft resetted the phone ,
now it's stuck in the splash screen before even the windows loading.
Plz plz plz help....
try doing a hard reset not just a soft reset that might help
medo_punsher said:
Hi ,
I was flashing my jasjam using sspl-herm and a 6.1 rom ,
While upgrading the progress bar reached the end but it stayed saying upgrade in progress , it took too longer than normal and i knew it wouldnt continue so i soft resetted the phone ,
now it's stuck in the splash screen before even the windows loading.
Plz plz plz help....
Click to expand...
Click to collapse
if u have loaded hardspl then hold power button + OK button on sides of phone and then stick stylus into reset button an dthis should get u 2 red, green, white, blue colour screen and then plug usb in and re-flash
get hermes in bootloader mode, connect USB cable and flash with this http://www.4shared.com/file/61372397/e2bf76c0/official_ATT_WM6_striped.html
Hey ,
Thnx guys 4 help
1st I tried hard resetting and it didnt work
2nd I DONT have hard spl
3rd I get into bootloader , i plug the usb cable but i cant flash , the ruuwrapper program says error during upgrade , i think it cant access the phone first coz the mobile device icon in my computer is emtpy , second activesync says not connected(although it tries to) and device manager reads an " htc usb sync " drive but no letter or something
Still no luck , any help ??
Activesync doesn't need to be runing.
download mtty and do like he said here "http://wiki.xda-developers.com/index.php?pagename=Instructions for those stuck on Boot Screen" (copy all text between " " and paste to your browser).
After "set 14" give "task 8"
Try flashing from SD card, first the HardSpl ant then the Original Stripped ROM.
@TheMim : tried but didnt work
@eryunt : how ?? i have a custom rom with the name HERMIMG.nbh on my sd card but it doesnt upgrade it says loading for a few seconds then some red numbers and letters appear at the top of the screen then it goes into the bootloader and doesnt upgrade
NOTE THAT : i dont have hard spl (no supercid)
Thnx again , plz help
Try downloading HARDSpl7 from here:
http://forum.xda-developers.com/attachment.php?attachmentid=35136&d=1173326890
Unzip it and rename the file "RUU_signed.nbh" in "HERMIMG.nbh"; put it on SD and so you will flash the HARDSpl.
Then, make the same thing with the file "RUU_signed.nbh" extracted from an original shipped ROM.
Hope it fixes your Tytn
Many thanks for your help , i will try that tomorrow but one final question ,
How can i access my sd card with no phone ?? do i need an external sd-to-usb device or something like that ??
medo_punsher said:
How can i access my sd card with no phone ?? do i need an external sd-to-usb device or something like that ??
Click to expand...
Click to collapse
Yes, you need an SD-Reader for your PC
Okay , now i have a cooked rom on my sd card (fat32 formatted) named HERMIMG.nbh when i get into bootloader it says loading for a few second then a red number "00068002" appears at the top of the screen and it continues to the tri-colour bootloader
any help ??
Have You already installed HARDSpl correctly via SD-card?
No , i didnt but will it work or i will get the same red number ??
PS : my bootloader version is 1.04 so i guess i dont need hard spl as this one can flash any rom , right ??
medo_punsher said:
No , i didnt but will it work or i will get the same red number ??
PS : my bootloader version is 1.04 so i guess i dont need hard spl as this one can flash any rom , right ??
Click to expand...
Click to collapse
Try downloading HARDSpl7 from here:
http://forum.xda-developers.com/attachment.php?attachmentid=35136&d=1173326890
Unzip it and rename the file "RUU_signed.nbh" in "HERMIMG.nbh"; put it on SD and so you will flash the HARDSpl.
Then, make the same thing with the file "RUU_signed.nbh" extracted from an original shipped ROM.
JUST FOLLOW ALL THE STEPS ABOVE
No no no no..... HSPL cant be upgraded now via SD card cause th SSPL was unsuccesfull!!!!!.....
Get a XP PC... your batt must be 50% charged or more "better", a working USB cable
NO SD CARD inserted... your XP pc must have NET frameworks 3.5
put your device in bootloader mode.... and upgrade any stock rom to rewrite a valid SPL cause your is corrupted now
then when you get a stock rom working via SSPL you will be able to redo the steps to flash HSPL V7