Artemis Loadboot - P3300, MDA Compact III ROM Development

hi, everyone, i have one artemis but this pda doesn't pass the load boot window, i have try the hard reset and it won't pass for windows... so, i can't syncronise the phone with pc to put a new rom, plz help!!

soft restart , when the screne is out ...then press power&voice button at the same time,
then u can see three colour ....after that insert u usb cable..... now u can flash your PDA....GOOD LUCK.

dear friend, the three colour menu apears and the pc recognize the pda, but in the RUU instaler, apear error code #260 (update error).
i try the artemis USPL to free the CID...
with Shady 313 ROM, the error is #260 (file open).
plzzzz with my diamond this process is very easy :S i'm broken my head with this pda model

SOLVED tks

Related

"Serial v1.06" - i-mate Pocket PC froze

Hi,
I just started with the ROM upgrade of my I-mate Pocket PC to 1.72.00wwe (obtained from the I-mate website) when my phone switched off. Now it only has (at the top) "Serial" and (at the bottom) "v1.06". No matter what I do - soft or hard reset nothing happens, obviously the power button also doesn't function. On my PC desktop I got the message that I need to reset my phone and re-connect.... can't get my phone going, so here I am.
The solution to my problem is (hopefully) simple ? I will really appreciate if you could help me with this ?
not a problem hopefully....u just made HimaClearJumpCode.exe run on ur device(this file exists in ur upgrade folder),and now ur stuck in the bootloader mode....
do the following:
1-hard reset ur device(it wont boot,off course)...
2-put it in the cradle,u should see that ur XP has found a new hardware(if it doesn't,change the USB port)
3-now run the himaupgradeUt.exe.
Now in case(just in case),those procedures didn't work,go to plan B.. :wink:
1-take the battery off ur Himalaya.
2-leave ur device for 12hours(it won't need all that time,but to be on the safe side,u know... :wink: ) without battery,so that backup battery drains...
3-put back the battery,recharge and enter the OS(this option wont work if u have erased the ROM)
4-rerun the upgrade...
good luck.....
RAGO :lol:
Hi
OK, what happens if the ROM is erased.... (judging by the fact that nothing happens when I put it in the cradle - with power on the cradle) ?
My phone was off for about 12-hours - blank screen when I got here this morning.
If I put it in the cradle (and after changing between all the available USB ports on my PC) the PC doesn't detect it - ActiveSync doesn't connect to the phone at all... Note : I have power on the cradle, and it's been a hour now - still just "USB" "v1.06" (or "Serial" if I take it out of the cradle).
:?:
so it is connected!!!!!!!!
since ur serial on the top of ur screen changes to USB when u put it in cradle,then it's connected.... :wink:
now just run the HimaUpgradeUt.exe in the folder that contains the NK.nbf file(32MB,it's the ROM),and it should start the upgrade....
be sure the NK.nbf is a Himalaya ROM....
good luck...
RAGO :lol:
Hi,
Thanks, did it just after posting my reply and everything worked out fine. Note, I just ran the ROM upgrade file (not HimaUpgradeUT), which I got from the clubimate webste.
Thanks, once again for helping me with this one.
Himalaya pocket pc - screen frozen on bootloader
Hi,
My problem is the same - but the difference is that whenever i run the himaupgradeut i get a connection error saying that the PC cannot identify the cradle as connected.
What should I do now?

Upgrading without activesync

After a interruptus ROM upgrade my s200 d'ont start . after the HTC i have a white screen but not more.
The activesync don't connect and i can't put the ROM another time.
I obtain the multicoloured screen with usb in the left botton.
Please, could anybody help me to update the rom in this situation , mayby without activesync ??
Regards.
Edit/Delete Message
i sugest you ask here
http://forum.xda-developers.com/forumdisplay.php?f=293
as more % of the readers of that forum have the same device as
you then this forum
All is OK , Thank's
Yes thank's, i found a ROM that don't need activesync , after that changing that rom by my rom and at the moment my s200 y ok.
Thank's.
tehe same problem
hi
i have a qtek 8310 and have the same problem that u, could u tell me what kind of rom does not need activesync, please?
thanks a lot
Indeed, I have the same problem with my S200, please explain what you did to fix your phone!
For those interrested: I've found the following text in the readme file of the regular ROM updaters (RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID in this case):
8. Q: I use RUU to update and failed, and my device always boots in three-color mode and cannot enter CE OS anymore, what should I do now?
A: If the update process has failed, you will see that your device will always boot in three-color mode. It’s normal and can be recovered. Please follow the instructions below to reset your device and to establish a connection with the computer.
1. Disconnect your PDA Phone from the USB cradle/cable.
2. Reset your PDA Phone.
3. Reconnect your PDA Phone to the USB cradle/cable.
4. Check that the communication cradle/cable is connected properly.
5. Return to the ROM Update Utility.
Note: You should ignore the ActiveSync connection.

O2 XDA Zinc. Please, help!

Hello all!
I've purchased O2 XDA Zinc in Arabian. I'm living in Russia now.
When I open the box, get the PDA and turn them on I've got screen like this:
mars II eboot ver......
h/w version v1.4
******** usb loader ***********
diskonchip g4 128mb
start downloading image...
please plug-in usb cable...
And that's all... Now I can't go to Arabian to change my PDA and there is no service center that can fix it in Russia
I tried soft and hard reset and no effect.
When I connect PDA to PC the new hardware "Asus USB sync" appear in system, but Active Sync does not recognise them (I have 4.5 version).
All o2 zinc upgrade software are working with active sync and available os and i can't use them.
I've extracted binary filles from update exe, larger of it i've rename to MarsII_G4.ABI and put it on SD. But after insterting card and restarting nothing happens.
I also have some knowledge of elelectronic.
So, please help, how can I fix my PDA?
Thank you in advise!
ok fer
find another ppc first
find a dos app and rename it to devicespy.exe and make it readonly
transfer it to windows directory of other ppc and plug it to pc via mini usb and activesync 4.5
download and run any zinc rom from seeo2
if you did it well the upgrade software cant recognize the device type so continue update progres until your ppc get reset.
replace that ppc with your zinc and update will continue to end and your zinc will be fin.
choose any lang you wish.
You'd better visit www.seeO2.com
and register with your IMEI.
Then you can download WM5 or WM6 official rom.
Hope this can help
Yeaaa!!
It's really working!!
Thank you!
I've recovered my device by using this method.
O2 XDA Zinc. Please, help
Hi where can I get dos app file??
hi all......
i do really need help for reviving my dead o2 zinc.
it is suddenly dead wen connected to notebook via activesync.
yes.. it is SUDDENLY DEAD.
i'm doing nothing.
i have been trying to entering bootloader (by pressing right d-pad plus soft reset), but the bootloader doesn't show up.
doing hard reset, but nothing happen. still dead.
one thing that works is...
there is blinking orange LED when i connected zinc with wall charger (without battery inserted)
and there is orange LED (showing up about 3-5 secs) when i connected zinc with wall charger (with battery inserted)
anyone can help me solving this?
how bout using mtty?
anyone knows?

My QTEK 9000 IS DEAD, PLSSSSS HELP ME

Hello,
I connect my qtek with pc. I tried to install wwe rom - from german to english. I ws downloaded english rom but cant install coz i have problem with COUNTRY ERROR -ERROR 120 atfer that i install in qtek "MaUpgradeUt_noID".exe and after that my qtek go to hell.
when i done hard reset on the screen write only: Serial and v1.00!!!!
..............qtek is dead...................
PLzzzz people help meeeeeeeeee
what can i do now for repair my qtek?????
p.s. srry for my bad english
Kind regards
Your Uni still alive
Try to download "Exit Bootloader.exe" from wiki, conect the uni to USB and Run the applcation...
If you uni is death when the Bootloader is lost. I brick my Jasjar when the Bootloader was gone, dont worry Try to read more in the forum Universal WM6.
AIN1 said:
Try to download "Exit Bootloader.exe" from wiki, conect the uni to USB and Run the applcation...
If you uni is death when the Bootloader is lost. I brick my Jasjar when the Bootloader was gone, dont worry Try to read more in the forum Universal WM6.
Click to expand...
Click to collapse
Hi AIN,
Thnks Mucho Mucho!
My Problem is, that i can only choose Com 1 to Com 3 in mtty 1.42 - Because of this i can't use the methode which is explained. - What i am making wrong? - I use a Sony Vaio Laptop for booting...
Thanks a lot!
if you have the rom try tis out!
1.unzip the file!
2.put the rom-extended rom-radio(or whatever you need!) in this folder
3.when you'll connect the phone on the usb,on the screen you have to see "usb v1.01".
4.run the "MaUpgradeUt_noID.exe"
5.wait till it will finish flashing!!
6.enjoy the new rom!!
qtek pu10 0r 9000 is freeze please big help
please big help / i just try to change language on my qtek 9000 and when the phone finish. and the screen freeze. and i off it and on it .and still the display show but freezing. and it can't connect to the active sync and pc /please help
Try a soft-reset first.
If not, you may have to hard-reset. You will lose all your data and programs you've installed and it will revert to factory state (or last flashed ROM).

Bricked JasJam , help :(:(

Hi ,
I was flashing my jasjam using sspl-herm and a 6.1 rom ,
While upgrading the progress bar reached the end but it stayed saying upgrade in progress , it took too longer than normal and i knew it wouldnt continue so i soft resetted the phone ,
now it's stuck in the splash screen before even the windows loading.
Plz plz plz help....
try doing a hard reset not just a soft reset that might help
medo_punsher said:
Hi ,
I was flashing my jasjam using sspl-herm and a 6.1 rom ,
While upgrading the progress bar reached the end but it stayed saying upgrade in progress , it took too longer than normal and i knew it wouldnt continue so i soft resetted the phone ,
now it's stuck in the splash screen before even the windows loading.
Plz plz plz help....
Click to expand...
Click to collapse
if u have loaded hardspl then hold power button + OK button on sides of phone and then stick stylus into reset button an dthis should get u 2 red, green, white, blue colour screen and then plug usb in and re-flash
get hermes in bootloader mode, connect USB cable and flash with this http://www.4shared.com/file/61372397/e2bf76c0/official_ATT_WM6_striped.html
Hey ,
Thnx guys 4 help
1st I tried hard resetting and it didnt work
2nd I DONT have hard spl
3rd I get into bootloader , i plug the usb cable but i cant flash , the ruuwrapper program says error during upgrade , i think it cant access the phone first coz the mobile device icon in my computer is emtpy , second activesync says not connected(although it tries to) and device manager reads an " htc usb sync " drive but no letter or something
Still no luck , any help ??
Activesync doesn't need to be runing.
download mtty and do like he said here "http://wiki.xda-developers.com/index.php?pagename=Instructions for those stuck on Boot Screen" (copy all text between " " and paste to your browser).
After "set 14" give "task 8"
Try flashing from SD card, first the HardSpl ant then the Original Stripped ROM.
@TheMim : tried but didnt work
@eryunt : how ?? i have a custom rom with the name HERMIMG.nbh on my sd card but it doesnt upgrade it says loading for a few seconds then some red numbers and letters appear at the top of the screen then it goes into the bootloader and doesnt upgrade
NOTE THAT : i dont have hard spl (no supercid)
Thnx again , plz help
Try downloading HARDSpl7 from here:
http://forum.xda-developers.com/attachment.php?attachmentid=35136&d=1173326890
Unzip it and rename the file "RUU_signed.nbh" in "HERMIMG.nbh"; put it on SD and so you will flash the HARDSpl.
Then, make the same thing with the file "RUU_signed.nbh" extracted from an original shipped ROM.
Hope it fixes your Tytn
Many thanks for your help , i will try that tomorrow but one final question ,
How can i access my sd card with no phone ?? do i need an external sd-to-usb device or something like that ??
medo_punsher said:
How can i access my sd card with no phone ?? do i need an external sd-to-usb device or something like that ??
Click to expand...
Click to collapse
Yes, you need an SD-Reader for your PC
Okay , now i have a cooked rom on my sd card (fat32 formatted) named HERMIMG.nbh when i get into bootloader it says loading for a few second then a red number "00068002" appears at the top of the screen and it continues to the tri-colour bootloader
any help ??
Have You already installed HARDSpl correctly via SD-card?
No , i didnt but will it work or i will get the same red number ??
PS : my bootloader version is 1.04 so i guess i dont need hard spl as this one can flash any rom , right ??
medo_punsher said:
No , i didnt but will it work or i will get the same red number ??
PS : my bootloader version is 1.04 so i guess i dont need hard spl as this one can flash any rom , right ??
Click to expand...
Click to collapse
Try downloading HARDSpl7 from here:
http://forum.xda-developers.com/attachment.php?attachmentid=35136&d=1173326890
Unzip it and rename the file "RUU_signed.nbh" in "HERMIMG.nbh"; put it on SD and so you will flash the HARDSpl.
Then, make the same thing with the file "RUU_signed.nbh" extracted from an original shipped ROM.
JUST FOLLOW ALL THE STEPS ABOVE
No no no no..... HSPL cant be upgraded now via SD card cause th SSPL was unsuccesfull!!!!!.....
Get a XP PC... your batt must be 50% charged or more "better", a working USB cable
NO SD CARD inserted... your XP pc must have NET frameworks 3.5
put your device in bootloader mode.... and upgrade any stock rom to rewrite a valid SPL cause your is corrupted now
then when you get a stock rom working via SSPL you will be able to redo the steps to flash HSPL V7

Categories

Resources