i just tried to upgrade my xda IIs to wm5.0 rom. after i upgrade it, it halted on the screen 'serial' at the top, '2.07' at the bottom. how to solve it? while i plug in the xda usb cable into the device, the screen not changed to usb. how to solve it?
There are few things you may try:
1.Reset button
2.Remove battery and place it again
3.MTTY method
4.Last but not least try to learn to use Search
i tried the reset button...it also can't...if i dont have usb cradle, but i have usb cable (Xda) only. may i restore back wm2003se?
Related
While upgrading my XDAII to the new O2 rom, I got a connection error which tiole me to disconnect the xda and do a soft reset.
I did this and it's now stuck on the O2 boot screen and wont budge, wont connect via active sync and does nothing else when I hard reset.
Have I f**ked it up ??
Please help,
Tommy
Don't panic
Just reset the device, place it back in the cradle and re-run the upgrade. It doesn't require Activesync as the upgrade process looks after its own connection.
Make sure the cradle is connected directly into a USB port on your PC and not to a hub. Also make sure the power supply is connected to the cradle.
Thanks, but that doesnt seem to help, the program just says that their is no connection.
Do you have another PC you can use? or try using a different USB port.
tried it on both and nothing, It looks like the XDAII can't start up properly and that's why it can't establish a connection. As I said it's stuck on the O2 boot screen (the one with the bubbles on it) with the version nos at the bottom and does nowt else.
I feel sick...
Tommy
OK. I misunderstood. I thought you were in the bootloader screen. So you need to see if you can put the device into bootloader mode. Press the jog button (bottom middle front of device) and power button at same time whilst pressing the reset button. This (hopefully) will put you in the bootloader - a dark screen with Serial 1.xx displayed. Then when device is put in cradle it should change to USB 1.xx. Then you can re-run the upgrade.
Whayhey
DCS you are indeed the man!
Thanks for your help.
Tommy
Is there any program like XDATools/XDArit for HTC Universal ?
my XDA EXEC have a big problem, always show BootLoader when i press power button (i don't need pressing power + - + backlight at the same time)
If i connect it to my PC, it always shown as "Unknown device" no matter which USB Port i plugged.
Also mtty1.16 & 1.42 cannot read any USB. It only read COM port. Restarting pc, softreset, hardreset aren't affected mtty's. It stills read only COM port and USB is none.
So my conclusion is download original rom, using a program like XDATools/XDArit for WM5 to flash my SD card, inject my sd to my XDA EXEC and run it (is my conclusion right?)
Sorry if my english is not good, cuz right now i'm in total despair to revive my XDA EXEC.
Please help me.....
while doing the gps upgrade, I was doing step 4 (Run the Alltel ROM exe file ) it failed at 8% then sent me to a recovery page after i removed the battery my touch wont do anything ,i tried soft reset ,camera and even hard .the only time i see anything is when i plug a usb cable in ,just a red light in the speaker hole.
try getting it to bootloader (hold power button, camera button and soft reset button) it should display a tricolor screen. now just plug in the usb cable and reflash the same rom or a different one
tried that it didn't work
What is the bootloader version you are using? 0.4 or 2.31
If you see 2.31.CoKE, you should be fine, but read more, more, more!!!
Don't want to sound like I'm not helping, but I am no expert right now, so don't want to further cause damage to your phone.
So go here:
http://forum.ppcgeeks.com/showthread.php?t=24979
i'm having a somewhat related problem..
I rom updated.. phone works but get a USB not recognized error when i plug it into any xp box.
I guess i need to try an activesync cab file..
if that doesn't work.. i'll reflash a rom through SD method once i find out how.
Anyone got a link for that?
Hello All,
My HTC Diamond Handset serial no is HT826K******* Tryed to change the ROM , but after reaching to 100% also the completed mesage is not coming . When I press the reset button Tri colour screen appears with error messgae " Upgrade ROM code error Please try Again".. . Please help
You probably don`t have the correct update package for your device... If you really want to update to this rom then you need the HardSPL. Install the HardSPL 1.93 Unsigned Developer edition.
do you have Hard-SPL?
I Recently updated through ROMUpdateUtility know i see touch diamond screen with RUU_Signed_1_93OliNex_HSPL_UnsignedEdition ...Please help
just flash another ROM while in bootloader and connected to usb. I would suggest to use a simply rom.
Hi,
But How , I am not able to copy the file to Internal memory as when I connect to laptop the the internal memory is not visible:
you don't need to put the nbh file in internal storage. Turn your device off. Press and hold the volume down button. While doing so press the power button. Keep holding the volume down button pressed until you see the multi colored screen which is called the bootloader. At the bottom it should say Serial. Using the USB cable with which you sync to your PC, plug the cable in to your PC and then plug the other end into your device.
The multi colored screen should soon say USB at the bottom of the screen. You are now ready to flash a new ROM. Just run the RUU as you would normally.
I did that; know I got the tri colour scree ;which says USB in white area know how to run RUU , my htc is connected to my laptop
create a folder on your pc and name it anything. now copy the nbh ans ruu.exe in that folder. run the ruu by double clicking it. this should be done when you get usb on your screen, if done correctly you rom flash should start flashing and a bar will appear on your phone.
Thanks All
Hi All,
Problem got fixed .
Solution used:-
Unsigned-Hard-SPL-Diamond-OliNex(2)
rumbles said:
you don't need to put the nbh file in internal storage. Turn your device off. Press and hold the volume down button. While doing so press the power button. Keep holding the volume down button pressed until you see the multi colored screen which is called the bootloader. At the bottom it should say Serial. Using the USB cable with which you sync to your PC, plug the cable in to your PC and then plug the other end into your device.
The multi colored screen should soon say USB at the bottom of the screen. You are now ready to flash a new ROM. Just run the RUU as you would normally.
Click to expand...
Click to collapse
so wut happens if i get no usb then wuts the matter ???
need to know what problem i have becuase i can never connect the fone via usb
Dynomite232 said:
so wut happens if i get no usb then wuts the matter ???
need to know what problem i have becuase i can never connect the fone via usb
Click to expand...
Click to collapse
Do you have the correct drivers installed?
Or Windows Mobile Device Center?
I think you need that I'm not too sure, I do anyway
hello
i have htc one x
firstly i didn`t know its problem
when i connect it with my laptop my laptop shows"usb device not recognized"
i thought this is because unofficial Rom
so i put a rom software via wifi "moborobo" on the phone
and tried to flash it via booltloader but without wiping
now it is still rebooting and can`t access to recovery or anything " i think it called boot loop "
and cant solve it by fastboot cause it is not recognized on laptop
so u think what is the problem
trying to replace usb port or doing what ?
is usb port is connected to the board so i have to replace the whole board ?!
what steps should i do ?!!
or it is already damaged and no hope !!!
please help
mostafa_tofa said:
hello
i have htc one x
firstly i didn`t know its problem
when i connect it with my laptop my laptop shows"usb device not recognized"
i thought this is because unofficial Rom
so i put a rom software via wifi "moborobo" on the phone
and tried to flash it via booltloader but without wiping
now it is still rebooting and can`t access to recovery or anything " i think it called boot loop "
and cant solve it by fastboot cause it is not recognized on laptop
so u think what is the problem
trying to replace usb port or doing what ?
is usb port is connected to the board so i have to replace the whole board ?!
what steps should i do ?!!
or it is already damaged and no hope !!!
please help
Click to expand...
Click to collapse
Are you able to access the bootloader? (Holding down the on button and volume down button)
VoLTz4Dayz said:
Are you able to access the bootloader? (Holding down the on button and volume down button)
Click to expand...
Click to collapse
after days the battery is out
and i don`t know what happend now it is not charging also and cant open
mostafa_tofa said:
after days the battery is out
and i don`t know what happend now it is not charging also and cant open
Click to expand...
Click to collapse
Ah .. Are you sure it won't charge? Try plugging it into your PC and a normal charger.
VoLTz4Dayz said:
Ah .. Are you sure it won't charge? Try plugging it into your PC and a normal charger.
Click to expand...
Click to collapse
no it is not charging
when i connect it to lap top or charger
it still shows intermittent red light
it its not charging and and still shows the red light intermittent red light
usb port is damaged or what ?!!
and if it is damaged this port is connected to the board ?! or i can replace another one without changing the board ?!
When you hooked it up to the pc and the red light starts blinking try to keep pressing combo buttons. Power and volume down button, keep them pressed and try if needed many times. Check to see if you can get it to the bootloader. Once it hits the bootloader you execute this script with admin rights from the fastboot folder on the pc
https://www.dropbox.com/s/aaah8gqz8j024xz/Batt script.bat
Mr Hofs said:
When you hooked it up to the pc and the red light starts blinking try to keep pressing combo buttons. Power and volume down button, keep them pressed and try if needed many times. Check to see if you can get it to the bootloader. Once it hits the bootloader you execute this script with admin rights from the fastboot folder on the pc
[ur
Click to expand...
Click to collapse
i got in to the bootloader
but the laptop shows"usb device not recognized"
and doesn`t accept any commands
and doesn`t acces to recovery or factory reset
just question usb socket is a aprt of the board or sparated part i can replace it without canging the whole board ?!!!
it just a suggestion it is because usb charging socket
Afaik it's part of the mobo. But are you using the original HTC cable, isn't it the cable at fault ? Using a straight powered usb 2.0 port on the pc ?
Mr Hofs said:
Afaik it's part of the mobo. But are you using the original HTC cable, isn't it the cable at fault ? Using a straight powered usb 2.0 port on the pc ?
Click to expand...
Click to collapse
what do you mean by "aAfaik it`s part of the mobo" ?! u mean usb socket is a part of the board ?!!
and i`m using the original cable and a straight powerd usb 2 port
i tried it with many cables and laptops and pc they are all the same
so what ?!!!!!!!!!
any suggestions ?!!! what i have to do !!!
any thing ?!!
Take it to a shop !