Hi all,
My XDA IIs works well before. But few days ago the Power button doesnt work properly, it can turn on the phone, hold to turn off the back light, but I can't use it to turn my phone screen off like before. Anyone has same problem ?
Can you see any part of the screen? It might just be that the backlight adjustments are set too low when the unit isn't cradled. You might be able to see the screen in daylight.. or maybe it was inside your home. I forgot where I was at when it happened to me. In anycase, if you can see a bit of images on your screen, go into the Backlight properties and change the setting to your liking.
Good luck..
The problem is i can just press the power button to turn off my phone BEFORE (the screen is completly off), and NOW it doesnt work at all ! When my phone was off, I can press the Power button to turn it on, or when I hold it for few seconds the back light will be turned off, but press once to turn off. I dont know why, if somthing wrong with the Power button it should be doesnt work at all, that's mean i cannot turn on my phone as well. But other functions of the Power button are still work well, except the 'Turn off' :roll:
power off doesn't work anymore
I have the same problem here. I can't use the power button to power off my qtek 9090!!
i can use the power button to turn my pda on and to switch the background light on and off - so the "hardware side" of the power button is working.
however, i can't use the power button to turn off the device. it's very annoying, because i can't put it in my pocket after finishing a call :-(
this should be some sort of a software problem - so i hard resetted my device (a couple of times) - but that didn't help!
can anyone help?
thanks,
lorenz
the ba doesn't turn off it is always on staand by mode. ->settings -> system -> button lock
this will stop any missed call because when the ba is in standby the power button is the only one to work
power on is no problem. i can't put my BA into standby mode. if i press the power button while the BA is turned on, nothing will happen. the screen will stay on, the background light stays on.
i have no way to put it into stand-by with the power button!
try this and see if it works. it's a software app that wil rest, shut down, and turn the screen off. just copy it to your BA temp directory and install it.
power button problem
nemchua
Is your problem solved ?
Because I have the same problem.
Power of switch doesn't work !!!
Any help would be welcome.
power button problem
Does anyone solve the problem???
Had the same problem...
I had the same problem going on for about two weeks or so...never changed anything and it went away all by itself.
The problem has not come back now in over 4 months.
Sure would love to know what the problem was tho...
Greetings,
Noddy
Power Off does not work
Add my name to people with this problem.
The only event I can link it to is this: I deleted my Motorola Bluetooth headset and installed a Logitech headset. I noticed the problem (can't turn OFF with POWER BUTTON) soon after that.
same problem for me ..... someone must know !!!!
I think it is a hardware problem. The contact is not making cleanly. Disassemble and spray time, perhaps.
It's a standard push switch, easy enough to replace, I occasionally list themon ebay but any phone repairier should have them in stock.
Richard
i had same problem yesterday afternoon, but it is ok now. recovered by himself
Write again in two weeks and let us know if it is still healthy. In my case, anintermittent problem became continuous.
Can't turn the screen on after pressing power button
I have a problem with my Bell Atrix. After pressing power button to lock the screen, i can't wake up the screen up by pressing that button again. Could anyone tell me how to fix it pls.
When I'm carrying around my BA, the buttons get accidentally pressed almost constantly.....which causes it to turn on, and it drains my battery alot.
Is there anything I can do or any program I can download that will lock all the keys when it's turned off, so that only the power button works? The power button getting accidently pressed isn't a problem becuase it's on the top of the BA.
it's already possible
look under settings->system-> buttons (or sth. like that, don't know the english entry)
Thanks......I can't believe that I didn't see it before.
Hi everyone,
I am trying to develop an application to run on this device and am having a few issues. I have no idea if it is actually possible to do these things or not so any help would be appreciated.
1 - disable the power button so the device cannot be turned off by the user
2 - re-program the hang up button so this goes to the app rather than the today screen
3 - program the IE button so this runs the app when pressed in tomtom rather than IE (i can get this to work anywhere else using the buttons icon in the settings menu but it persists in running IE when used when tomtom is in teh foreground)
Many thanks.
I've just installed Schaps 3.54c on a friend's JasJam. She now has a strange issue where she turns the screen on, taps on the Today screen to unlock the device and then pressing the green phone button doesn't do anything. But if you tap Start then go into Programs or Settings and THEN try the green button, it works fine!
Has anyone experienced this?
i have notice this little bug now and again, i just have to click the ok button then i get all control back to the call button.
Not sure what causes it though.
Its like another proggy is running in the background.
After installing TomTom7, my quick list screen, activated by holding down the end-call button, takes about 5-10 seconds before it appears. Before installing TomTom it came up pretty much instantly.
It's a bit annoying as I like using it to lock the device or set vibrate quickly.
Has anyone else had the same issue, and managed to fix it?
Thanks all!