I Have 2 No Early 2005 (with the cog shaped camera pod) M2000's which have cracked screens, i have now managed to get hold of a working late 2005(with the round camera pod) unit with a duff PCB and swapped the front half (screen and keyboard). When i swap this over all i get is a white screen, is there a software problem and is this compatable. I have checked that the front half does work by fitting it in a late 2005 working unit
Hope someone can help
with thanks
Jubblyone
Same here
I, and others I have read about, have the same problem, but I haven't found of a solution. Let me know if you have any luck.
there are 2 types of screens on BAs..a Sony and Toppoly...u have to make sure u get the correct one for each device.
Related
Hey guys!
I'm experiencing a very strange and annoying issue with my BA, and I was wondering if I could get some input from you.
So, here goes:
The touchscreen (not LCD) in my unit was broken, and thus I decided to fix it. I purchased a new one off eBay a few weeks ago, and just yesteday I proceeded to install it. To my surprise, something seems to have gone wrong.
I power up the unit, make my way into "Allign screen", and then the last "cross" that I have to touch rarely clicks in. On the other hand, when it does get detected, it simply restarts the alligning process.
What I've tried so far:
- allign right after installation -> no luck
- hard reset (on WM2k5_v4_R2.1) -> no luck again
- opened up the unit again, repositioned the screen -> nothing
- upgraded to Logout_WM2K5_5.4.03_HN -> still nothing
Right now I'm out of ideas, and I was hoping somebody here has some. Do you think the new touchscreen might be flawed ? I'm already discussing this issue with the seller.
Thanks for reading
New touchscreen or a refurb? Same type? (toppolly / sony) Sounds like it's been stripped from an old unit to me as it's not recognising the taps in the right places - can you see somehting like a liquid spill anywhere on the panel? This is what it looks like when the overlay touches the glass.
Richard
http://cgi.ebay.ca/ws/eBayISAPI.dll?ViewItem&item=9720199180&rd=1&sspagename=STRK:MEWN:IT&rd=1
That was in fact my auction. Looked like brand spanking new to me, not one single stylus mark, and also had the protective sheet on. Of course, I might be wrong
Also, no liquid spill visible anywhere.
NSD said:
http://cgi.ebay.ca/ws/eBayISAPI.dll?ViewItem&item=9720199180&rd=1&sspagename=STRK%3AMEWN%3AIT&rd=1
That was in fact my auction. Looked like brand spanking new to me, not one single stylus mark, and also had the protective sheet on. Of course, I might be wrong
Also, no liquid spill visible anywhere.
Click to expand...
Click to collapse
I bought from him also and am yet to fit - I got the completley wrong module :-(
Richard
What do you mean wrong module ? The "tip" of the flex cable ? Mine seems to match with what was already there ...
Hey NSD!
I purchased the exact same module for my Himalaya device, after the touchscreen being cracked.
My father, who is an electronic engineer, soldered the flat wire from the touchscreen onto the rear side of the LCD with normal copper wires. Unfortunately I have the exact same problem a you!
After attaching the entire LCD (+touchscreen) onto the mainboard, and supplying power from the battery, I'm not able to go past the Align Screen section!!!
The touchscreen is from the manufacture 'Asian Media' (I think so...).
It can't be a coincidence, that both of our touchscreens don't respond to tapping!!!
Anybody been able to get this problem fixed??
Any help would be appreciated!!!
Kind Regards,
Tony Schattat
I never replaced the touchscreen of my BA but I have replaced the screen of my ex ipaq 6315 once.
And one thing that I know is that sometimes the screen align process is different from the normal, I mean, it keeps repeating and repeating again many times....until the unit finally passes the align step and finishes the configuration. Actually I´ve "aligned" the screen more than 30 x (when I replaced the screen).
It happened just once and then I had a completely normal unit.
Hi all,
my BA and me spent 5 nice years together, during that period I have changed 3 screens and had no other problems but recently BA suprised me (just few months after the last screen replacement) with weird problem.
Screen work, digitizer work but funny, it usually miss the place where I touch the screen 5 around 5 mm to the right, then I draw a note for eg and moving right line I draw lags after the stylus, after I start to draw to the left everything is fine. Up and down is fine too. If I align everything is fine for a some time but when I try it later its messed up again.
I tought that its software problem but after the hard reset nothing changed.
Is this problem familiar to anyone? Is it a time to change a screen again?
I dont believe that its worth, BA is rather old phone but I have previous screen with good digitizer and if you say that I should try to change a digitizer I ll try it (any manual for that? I saw just 4 contacts but covered with plastic and digitizer seems to be glued to the screen)...
Any ideas before I burry my beloved BA
thanks, best regards to BA community and special greetz to Chef Tony
ps
used to try to disassemble it, checked the cables - everything is fine (as long as I can see), they are connected nicely, beside that phone work fine, only problem is with the digitizer
Hello...friend, i got the same problem wit my Himalaya last time n guess what it works fine again after i put a small piece of paper between the phone n the battery..but unfortunately the charging port broken..
but i still have Blue Angel wit me wit no GSM problem..
About two months ago, my screen decided to die. I ended up getting a new phone, but I still had my Play sitting here bothering me. So I decided to get to fixing it.
When I tore it apart, I thought that the digitizer had died, but what I found was actually the connecting the digitiser, LCD and Buttons together was damaged.
So I ordered one on ebay for about $10. When I got the cable, it seemed to be about 3-4CM shorter than the OEM one. Which supports why I think this may have been a design error on Sony's part. What was happening was Sony's god awful mechanism for sliding the screen up and down had pinched the cable, and caused it to be damaged.
I know this might be a longshot, but I think that some people might be able to save a dead device by replacing this one simple part, I know it worked wonders for my play, as well as a friends.
I will post a link to the part as soon as my post count is up.
So not the digitalizer?
steamdnt said:
About two months ago, my screen decided to die. I ended up getting a new phone, but I still had my Play sitting here bothering me. So I decided to get to fixing it.
When I tore it apart, I thought that the digitizer had died, but what I found was actually the connecting the digitiser, LCD and Buttons together was damaged.
So I ordered one on ebay for about $10. When I got the cable, it seemed to be about 3-4CM shorter than the OEM one. Which supports why I think this may have been a design error on Sony's part. What was happening was Sony's god awful mechanism for sliding the screen up and down had pinched the cable, and caused it to be damaged.
I know this might be a longshot, but I think that some people might be able to save a dead device by replacing this one simple part, I know it worked wonders for my play, as well as a friends.
I will post a link to the part as soon as my post count is up.
Click to expand...
Click to collapse
so my xperia play has the same issue, i replaced the digitalizer and the touch screen still doesn't work. could i please ask which part specifically you replaced, thankyou
jakkebrown said:
so my xperia play has the same issue, i replaced the digitalizer and the touch screen still doesn't work. could i please ask which part specifically you replaced, thankyou
Click to expand...
Click to collapse
I am having this problem as well. touchscreen doesn't work nor does the home button. Volume down button seems to fail while in CWM recovery as well. I was thinking about replacing the digitizer but now I'm not so sure. Any help or advise would be greatly appreciated
If OP's saying what's busted is the part where all the digitizer, physical buttons, and LCD converge, that's the SLIDER FLEX. I replaced mine twice already. It gets pinched very easily. That's the weakness of slider phones. You have to accept that from the moment you decided to buy the Xperia PLAY. It happens to all sliders, live with it, face it.
Quick introduction. For experience and training purposes I started buying broken phones (LCD, digitizers) and try to repair them. I bought HTC Wildfire S with just cracked touch screen. Bought parts and replaced. When assembling phone back the screen did not work on the whole area, what I mean it was working like partially, only vertical left hand side was working. Like writing text message, R works, then E and T doesn't.
Tried to disconnect the digitizer connector, maybe it was not touching properly, couple times. But that didn't work. It was just working in different places than before. Found here a thread about a problem for different digitizer versions.
http://forum.xda-developers.com/showthread.php?t=1942259
But the thing is I have no idea how to approach anything that these people suggest. I don't know how to replace software, reinstall it or whatever involves soft. I would like to learn too.
If you have any ideas or suggestions please share with me, if not I will just sell the phone back as not working. Thanks
Yesterday i dropped my device from one feet. It turned off and i turned it on.
Now lower part of screen and capacitative buttons dont work. i will attach a image(non-working area outlined in red)
My warranty has expired so i cant exchange it for a new one. What should i do? Can i fix it by myself?
Please help me
Fycola123 said:
Yesterday i dropped my device from one feet. It turned off and i turned it on.
Now lower part of screen and capacitative buttons dont work. i will attach a image(non-working area outlined in red)
My warranty has expired so i cant exchange it for a new one. What should i do? Can i fix it by myself?
Please help me
Click to expand...
Click to collapse
Hi,
Only thing I can think of is that somehow it has damaged the cable from the touchscreen or the tiny wires that feed into the cable without damaging the screen. I came across a brand new screen I was replacing once for someone that had a similar problem where the bottom left hand corner wouldn't respond to touch unless there was firm pressure on the screen to create contact, and this was a brand new screen. It could also be that the touchscreen connector needs to be pushed back onto the board if it's come a bit loose.
If this is the problem, you can fix it by yourself although I'd have a good look around youtube, there are heaps of DIY videos of how to replace screens. If you do go down this path I recommend you replace the touchscreen/LCD/LCD frame in one go, as it's generally already pre- assembled the only thing here is that there are 3 brands of LCD's HTC used with the phone and they aren't all compatible, and you can only tell by pulling down your phone and looking at the LCD flex cable colours, and the other thing is that the screens that are available aren't always the same quality as the original. If this sounds to hard your best bet is to take it somewhere and diagnose the problem just in case it's something else