I have a qtek 2020 with v1.52 rom. I downloaded the new Italian rom (1.72.04ITA) from www.windowsmobile.it and I tried to upgrade it.
After erasing internal rom the upgrade process stopped with a fault message:
Error 112: ce rom update error
Now the display is dark. I can read “serial” or “USB” on it.
What’s happened?
I tried again 10 times but nothing.
It seems that connection between pc and qtek wasn’t correctly established. This because the little activesync icon (bottom right) is now always gray, never green.
Help me please!
Hm...
When OS is not started, PC ActiveSync cannot connect to your device, i think this is indeed...
But open Windows Task Manager and kill process wcescomm.exe (this is that tray icon of ActiveSync) and try to run update again...
HTH
> open Windows Task Manager and kill process
> wcescomm.exe and try to run update again
I tried but nothing.
I also tried to execute XDAtools but I recieved the following message:
Cannot execute the remote communication program.
Please make sure that USB/Serial cable is properly connected.
What can I do?
Does your device changes the screen from "Serial... blablabla..." to "USB... blablabla..." when you put it into cradle?
If so, what update writes when you try to run it (after putting device into cradle and killing activesync)?
> Does your device changes the screen from
> "Serial... blablabla..." to "USB... blablabla..."
> when you put it into cradle?
Exactly
> If so, what update writes when you try to run it
> (after putting device into cradle and killing ActiveSync)?
I can read following messages:
* Message 1 *
Cheking info on your pocket pc. Please don’t disconnect.
-----------------------------
* Message 2 *
Your pocket pc software is about to be update from:
Device CE image version: (now this is blank, the first time I attempted the upgrade was 1.52.00ITA)
Device CE extended image version: (now is blank, first time was 1.52.93)
Device Radio image version: (now is blank, first time was 1.06.1)
To
CE image version : 1.72.04
Extended image version: 1.72.128
Radio image version: 1.14.00
-----------------------------
* Message 3 *
The current software is being erased
Stage1: erasing ROM. Please wait
(But bar will stay at 0%)
-----------------------------
* Message 4 *
(After 2 minutes)
Error 112: ce rom update error
Any ideas?
Stupid question, but do you have pluged charger to cradle? I assume that so...
On other hand, I searched through this forum and found this links:
http://forum.xda-developers.com/viewtopic.php?t=10333
http://forum.xda-developers.com/viewtopic.php?t=8835
HTH
I tried, but nothing.
Anyway thank you for your reply
Hm... I was solving this issue yesterday and try to download update again (some corruption may come when update is downloaded) and flash it again...
I did it. I downloaded and tried also other international rom version, but nothing to do.
I’m going to call the costumer service ...
This is strange... :evil:
Unhappy, we are so far from each other... I want to help you...
Do you by chance have your cradle plugged into a USB hub? There have been many reports of problems in this configuration.
If so, try it with the QTek cradle plugged directly into the computer.
If not, a call to the service center may well be in order.
> we are so far from each other...
> I want to help you
You are very kind. But I live in Rome ...
> have your cradle plugged into a USB hub?
No, it is plugged directly into pc
Service center seems to be the only chance
:roll:
Me too..
Hi!
Just experienced the exact same thing :-(
I hate it!
I has done it one time before, and then I had to send it in to be repared. I dont know what they do, but I got it back working again.
But now when I saw the new official 1.72 rom, I wanted to give it another try.... but... now its dead again, doing the exact same thing as yours...
any news?
Regards
Peter.
You are very unlucky.
Today I’m going to call service center.
I hope they’ll solve problems quickly.
I’ll tell you what’s goin’ on.
Working!
hey!
I actually got it back to life!!
I took a different PC, connected my qtek and just started the upgraded again, even though the activesync wasnt connected. It started to upgrade, and my Qtek is now back to normal with 1.72!
Try if you can, with af different PC...
Today my service center replyied to my email regarding this, sayning that they couldnt help my, and there was no guarantee since i tryied to upgrade my self :-(
So, good thing i did it my self
I was thinking about it because I had some problems with usb ports on my pc. So this morning I tried the upgrade from another pc and ... YEEEAH.
I make it !!!
Now qtek 2020 works again !!!
Yeah!
Congratulations!
Good thing we have this forum
Experienced any problems with the upgrade yet?
yes.
still problems with bluetooth connection: no signal available from gps reciever. :shock:
problem solved by downloading bluetooth tools from:
http://bluetooth.i-networx.de/index_e.html :idea:
now it works fine.
bye
hi,
i just received my o2 xda 2, i decided to upgrade to 1.60 when i saw 1.72 it's out:
1st quest:
where could i find 1.72?
Does the qtek one works with my xda?
thnx
ciao mario!!come ti va col gps BT e tomtom3?
Hi!
I would definetly not try to do any upgrade as long as the upgrade isnt directly comming from your service center. All the XDA upgrades I tryied on my Qtek didnt work at all...!
Be carefull!
I was trying to upgrade the radio on Universal, somthing I did all the time on my magician. And I think the upgrade worked, I'm not sure. BUt now it won't get out of boot loader mode. If I hard resest and choe clear it says "clearing now" then just goes back to loader mode. I've tried every key combo I know. Power + reset, backlight + power + reset, pulling the battery. Nothing works! Anyone had this issue before? Any suggestions? :?: :?: :?: :?: :?: :?: :!:
That happend to me too. I tryed every thing ... not working ... then i upgrade to the last radio and (soft-reset and power botton) and it worked ... i havent make any upgrade after :lol:
Hi,
the same happened to me, but I solved the problem:
1.) Make the update without any card (SD + SIM) in the phone!
2.) Use the original USB-cable
Now it should work!
Greetings,
Teja
Thanks guys. Pulling out the SIM and the SD did work. I wonder why though? ANyway, thanks again.
A million thanks!!!
I read a lot of replies on other threads, and nothing worked.
Then your suggestion of the Sim + SD worked like a charm.
Thanks a bunch for restoring my expensive brick.
It took a long time for me to find out you've to remove the cards so I was about 2 weeks without my expensive MDA-Pro. And I'm looking forward if it helps anyone to solve the same problem!
Greetings,
Teja
As you've seen, it was my first post here...
Stuck at USB V1.01
New to this. I have a QTEK 9000 Spanish edition. Was upgrading the ROM and the PC for some reason restarted cutting the connection while ROM was in progress. now the PDA is stuck in USB V1.01 screen, tried to hard reset. nothing working. I have read posts about removing SIM and SD cards I have done this. I can not even connect back to the PC, I use the original USB cable, windows pings to suggest a connection is made BUT, now light shows uup on PDA to suggest a connection and Windows mobikle Device Center is not picking up the device. can anyone help me?
Hi, the same problem with me. So at last I am successful and I solve it. I suggest you. First you make update with out any card and then the second step you use the original USB cable.
Try the best.
Bootloader screen stuck!
I dun know i removed cards and hard reset but still its not connecting... show usb when connected to pc and Serial of not down at the bottom show v1.01
Any idea what should i do now?
hi to all
i have read the wiki of this blueangel,(but i dont found any solution)
this is the problem:
i have sim unlocked the BA, but when i put my sim card, the phone says "no service", and "unable to register on selected network"...all the times.
so, to "solve" this i did:
i update the room and the radio, with helmi room, and used the MaUpgradeUt_noID, to begin the update, i dont know if i am in the rigth way to solve the problem, but i have no more ideas...
another thing: sometimes when i turn on the device, at first screen(colored stripes screen) did not show number of the radio and another like G
and the worst: i have no backup of original room:
PH20B 0 B ESN N TELCE301 1.40.030 3, 1.40.178,1.12.00 12.00
PLSSS HELP ME!!!...
DARTHAS!SORRY FOR MY BAD ENGLISH)(
Hi all dear masters,
I was trying to upgrade my Imate PDA2k, it was failed and now it's not booting.. In the screen, just a "SERIAL" appearing and changes to "USB" when connected to the PC... I tried to upgrade again but now, it says "COUNTRY ID ERROR N-N-12-12-12" and aborting...
Is there anything that I can do?
Any help would be appreciated..
Thanks...
Sorry, I found WM6 upgrade and mtty1.2 and process brought my PDA back... Thank you..
I have the same problem
My mda compact 2 starting playing up yesterday, rebooting on its own, so I tried to install the upgrade from tmobile (ruu charmer). The upgrader stopped and my mda now has a screen that only either says serial v1.02 or usb v1.02.
I've tried rebooting it several times in several different ways without any joy, the screen just remains the same. I tried connecting to my laptop via active sync, but its like it doesn't exist anymore!
In simple terms, could someone please explain how to fix our problem.
Hello everyone, i am new to this forum, and I start with a really annoying problem
I have had an XDA orbit for a while on WM6, and i sent i back once becuase it started randomly turnign off then refused to turn on completly at one point. I then sent it back again after it was repaired, as it started to randomly power down again. However, this time I got a new orbit from O2.
However, my problem is that IO never see mto get signal :S all it does is keeps searching for signal, although occasionalyl when I do seem to get signal, it will nto make a call or sed any messages or the *#10# returns a "Failed" message. Withotu wanting to part from the phone again to get it repaired because I need it (and the GPS) in 8 days. I do kno that the simcard works because i re-tried it on my old old phone which has no problems with it and can make calls. Any adivce?
Stats:
O2 XDA Orbit (New out of box)
WM6
O2 Pay as you go Sim (With credit)
2GB Micro SD
IPL: 3.04.0001
SPL: 3.04.0000
GSM: 02.67.90
OS: 3.4.0.0
oh, and if anyone else can help me on this it would be appreciated aswell. Whenever i try to install the drivers for the phone on my computer, it fails as it says i have a more recent version of Vista Mobile Device Cetner, and i cannot get the SD card or its contents to appear on my computer.
Many thanks in advance
~Fribble