Related
Hi all,
I swapped my old O2 G2 BT headset for the new O2 one and have to say I noticed little improvement. I even upgraded to the 3900 build of the stack but no difference. However I then gotta thinking....
By default the profile being used was hands-free, but I seemed to remember the XDA2 using only headset. So - I found that by holding the -vol button for 15 secs I could register it as a headset profile (the XDA2s cannot use any of the hands-free bits anyway - voicedial etc etc).
Well, the audio quality is improved and the range appears to be better. It is still not perfect (or as good as it was on the XDA2) but it is now useable.
I am going to test for the week before I decide if I shall get a refund or not.
Cheers - Rich
Hi Rakh!
Where can I get the BT3900?
Thanks!
ftp://xda:[email protected] Upgrades/BroadcomCorp_BT1.0.0.3900.cab
Re: BT headset/handsfree profile - this might improve qualit
rakh1 said:
By default the profile being used was hands-free, but I seemed to remember the XDA2 using only headset. So - I found that by holding the -vol button for 15 secs I could register it as a headset profile (the XDA2s cannot use any of the hands-free bits anyway - voicedial etc etc).
Click to expand...
Click to collapse
the -vol button on the side?
When did you do that? - it doesn't seem to do anything on mine??
Thanks
--ian
Hi, yes the -vol button on the side. Switch it off (red light) wait 5 secs and then hold the -vol button for 15 (yes fifteen) seconds!
R
Hi,
Nope - still doesn't seem to do anything on mine. Either i'm doing something wrong or it only works on the xdaIIs and not the M2000 (they are suposed to be the same hardware but it might be a software thing).
Thanks anyway,
--ian
-vol button on the side of the O2 BT headset - not the XDA2s
Sorry for the confusion but I didn;t figure out what you were doing unitl now
Rich
Ahhhhh - doh!
Thanks for clearing that up.
I have a Jabra BT250 - and yes I was using the vol- on the phone
--ian
Jabra phones default to the headset program. Holding in the +Volume button on the headset while setting up for pairing turns on the optional Hands-free profile. This is just hte opposite of what the original post was about. The original poster had a G2 headset which defaults to Hands-free, but can be forced to Headset Profile.
Hi,
So what's the difference between headset and hands free?
--ian
Hands-free enables support for voice dialling etc etc etc. Headset simply allows you to use the mic and earpiece of the headset. I presume that the added functionality of the hands-free protocols take some of the 'bandwidth' from the voice part of the protocol and as a result exagerate the bad sound quality...???
R
Jabra headset
Hi to everyone!
I'm a Jabra user myself but I can't seem to enjoy the last number called redial feature with my XDA2 device (with ROM by Dr. Stein).
Any suggestions on how I can use this feature?
Thank you very much!
i have a motorola HS850.
it defaults to handsfree
anyone knows how to force it to headset?
it used to work such that when I open the boom on an incoming call, the call will automatically be answered.
now it doesnt work that way..
it just waits for either the bluetooth action button or the green answer button on xda iis to be pressed..
i have downgraded by BT [ recently upgraded to 3900 ] back to 3500 and the Motorola HS850 can auto answer whenever the boom is opened..
Guess 3900 is not perfect anymore
My HS850 works fine with BT 3900
Perfectly clear. Not tried switching handsfree to headset tho.
jabra bt 250
i m using a JAbra bt 250 and a qtek 9090..i tried the setting...but dont kno if it worked...in my shortcuts..it says hands-free connction to jabra..but i want it to be headset...coz thers too much of crackling right now..?
I have a O2 XDAIIs been tring to find what exactly I need to do to ativate voice command with my bluetooth headset I have being looking
through the forums but am unable to find the sollution if there is one can someone point me in the right dirrection PLEASE GOING NUTS
I don't think it is possible. Problems with the integratino of Windows Mobile and the Bluetooth Static/Profiles.
So, is this a Blue Angel Issue, a Windows Moblie SE isuse, or both?
If just a Windows Moblie SE Issue does anyone know if WM2005 corrects this?
Thanks!
Its a windows issue rather than a BA issue I think, however there is a partial solution.
Press the connect button on your BT headset as if you were answering a call; then press the "contacts" button on your BA. You should then be able to speak into your BT headset. Once finished, disconnect the BT headset as normal
Not perfect, but a reasonable workaround. I have my BA in a cradle in my car & hardly need to glance at it in order to find the contacts button & get nearly-handsfree operation
Its a windows issue rather than a BA issue I think, however there is a partial solution.
Press the connect button on your BT headset as if you were answering a call; then press the "contacts" button on your BA. You should then be able to speak into your BT headset. Once finished, disconnect the BT headset as normal
Not perfect, but a reasonable workaround. I have my BA in a cradle in my car & hardly need to glance at it in order to find the contacts button & get nearly-handsfree operation
Dear weasel,
I have tried what you have advised to get BT head set to activate voice command. However, it don't work. Is there any thing else that I can do? I really hope I can dial a call via BT haed set.
Thank you.
--------------------------------------------------------------------------------
Hi!
I have i mate JasJar, but there are some problems which are a bit annoying and I will ask you if you can help
Does anybody have problems using BT Jabra 500 working with Jasjar?
I cant hear any of my incoming/outgoing calls nor can I hear a ringing in BT.
Jasjar discover BT and pairing is OK ( just in case I did couple times -no luck)
when I use answer/end button on BT is dialing out but no sound on BT
on other side that I call they can hear my voice but I can't hear anything
Do I need any software to instal in jasjar ???
ROM version 1.13.53 WWE
ROM date 09\23\05
Radio version 1.03.01
Protocol version 42.36.P8
ExRom version 1.13.137 WWE
Please help me out
Thanx
I have BT 500 and have no problems, it sounds like the headset has a problem not the phone.
Also have my own and a client's Jabra 500 working successfully with o2 Xda Execs.
Stupid question I know, but you have tried increasing the volume on the headset buttons?
I did try everything , volume etc , contact jabra and try there sugestion
such as :
could be a pairing issue, or a bad speaker on the BT500. Please try a reset and re-pair of the phone and headset first:
Turn the headset off.
Plug the headset charging cord into a wall outlet.
Connect the headset to the charging cord for 5 seconds.
Disconnect the headset.
Remove the headset from the phone Bluetooth menu.
Turn the phone off.
Remove the battery (and sim card, if removable), and hold out for 5 seconds.
Re-install the battery (and sim card, if applicable) and turn the phone on, but do not touch any settings.
Turn the headset on.
Put the headset into pairing mode by pressing and holding the pairing button until you see a steady blue light. Release the button.
Perform the pairing procedure for the phone.
SIMPLY IS NOT WORKING
try with friend V3 razor and same thing
I also have the BT 500 + jasjar
It just works better than the BT 250 which was my past one.
To be honest, what I have on my jasjar is the new O2 rom upgrade (and that should not do any difference) I think there is something wrong with your jasjar
Maybe you will be forced to try the bad solution HARDREST try the headset with other phones before doing that
i beleive it's the headset that has the problem, since you tried it with another phone.
i have the bt500 with the imate jasjar and also the kjam and it's more than perfect for me, the sound is cristal clear on all the phones i tried on.
maybe you should replace it with a new one.
What I mean is not a factory mistake in the headset
I think the phoen is getting complex and some data have been lost (possible)
By the way, I haven't installed the BT headset fix, yet it works fine.
hello friends,
my logitech headset bluetooth seems to working properly,
it is properly recognized and function without problems until i shut the headset but ,when I turn it on again, the system does not recognize anymore. I have to remove the headset of the list from bluetooth devices and i have to register again on the system... to use it properly (until next headset shutdown).
Of course this does not happen wm6.0 original. I use Kavana rom (modified by Rickwatt).
someone know a remedy for this bug?
Thanks brothers
fwood said:
hello friends,
my logitech headset bluetooth seems to working properly,
it is properly recognized and function without problems until i shut the headset but ,when I turn it on again, the system does not recognize anymore. I have to remove the headset of the list from bluetooth devices and i have to register again on the system... to use it properly (until next headset shutdown).
Of course this does not happen wm6.0 original. I use Kavana rom (modified by Rickwatt).
someone know a remedy for this bug?
Thanks brothers
Click to expand...
Click to collapse
When you shutdown your headset, turn off bluetooth then back on then, turn on your headset, give it a try as thats what i do.
Generally also open up media player after headphone sync
Thank you for your reply Stylez.
I tried but unfortunately without success !If I'm going in bluetooth settings and select "set as heands-free" ... nothing happens. With the WM6.0 rom was in this way and the headset was recognized! I tried to turn off and on ..many times bluetooth and headset..... still nothing !
I must delete headset in the list and register it again!
I'm having same prob.
Hi,
I have a Qtek 2020 with WM6.1 (Athers Rom ) and after loosing my original headphone I've bought one from the net, wich I believe is from Qtek s200, it has two control boxes, one for volume and another one with a single button for anwsering calls. The problem is that the button doesn't work on my PPC. The volume works, the mic works, but the button doesn't do nothing.
Is there any kind of driver or software that alows me to give life to it?
Thanx