Develop Bugs

Trying to Upgrade ( Flash ) and now I am stuck in Bootloader

I tried the Upgrade, but it did never start, so when I tried to get it back to normal, doing a reset, I only get the Bootloader screen, with the USB and v0.60, I tried a Soft and Hard Reset but nonthing, I have tired to re-flash it again, but also nothing, please any help, thanks

I can not even to start the Flash program, I get ERROR : 101
ERROR 101 : CONNECTION ERROR
PLEASE ANY ADVICE IS WELCOME, THANKS

I WAS ABLE TO REFLASH IT, BUT I STILL GET TO BOOTLOADER ONLY
PLEASE HELP

latest ActiveSync installed? Removed battery?

Had this issue Yesterday. Even if You update the ROM, You will still stay in bootloader (for me it was like this). Do another update, this time only the radio (so delete ms_.nbf and nk.nbf from the directory from where You run your upgrade utility). After this (another 20 minutes) You should be able to have result after the cold-reset.
On the bootloader there is a small difference. Upgrading the ROM shows how far he actually is (in percentage), whilst upgrading Radio it does not show You the percentage, only that he is busy.
Ruud

Just try the update without any insert card (sd and sim), and a wonder will happen!
Teja

- connect the JASJAR with your PC using the USB cable. Activesync will NOT start and the XP says does recognize it
- do a HardReset (press the 2 (-) in the keyboard and softrest it all at the same time. Hardreset screen appears (DON'T press 0 or X..)
- start the update program. Please use a good upgrade like the latest from imate ftp://ftp.clubimate.com/JASJAR_WWE_11353_137_10301.zip
- start the update and when it's looking to check the version of the JASJAR softreset it
It should start to reflash it without problems.
I hope it helps...

Asus A636N, doesn't boot after failed upgrade to WM6

Hello!
Today I tried upgrading my A636N to WM6 using the pachage from the Asus download site ( http://support.asus.com/download/download.aspx?SLanguage=en-us&model=MyPal A636N ), and I didn't format the SD card to FAT before copying the files to the card. The upgrade tool started flashing, and then gave me an error at 36%. After reboot, the device hanged at the Asus blue screen at startup. It doesn't boot anymore, and the hard reset just gives me a blank screen.
Can anyone help me?
Could I flash the rom through USB? Or what could be done? Any advice is much appreciated!

ETEN M600 No bootloader mode possible

Hi guys,
After update to kozhura WM 6.1 R3, I decided to return to WM 5. Thereafter I wasn't able to enter in Bootloader mode anymore. What I did is installing the
M600_CHN_0170-winxp.exe by extracting renaming temp.dat temp.bin and copy this file and USB_DL_...exe on the SD Card. After copying both files I have tried to enter boot loader mode and it wasn't able to do so. By pressing Power + Reset and releasing Power, entering boot loader is not possible anymore. I also tried to enter in Bootloader mode by running M600 update software. Screen starts flashing, white light and then restart...enter in WM 5 again.
SO I have WM5 running now, I'm able to connect to Active Sync, but the Bootloader mode is not working anymore.. screen is flashing and then M600is restarting. I cannot make any update on the Pocket PC, even original image install is not possible anymore ? I cannot install also any other image ?
What to do ? Any ideas how to recover the bootloader ?
I think that the 170 ROM somehow overwritten the original bootloader and it is not recognizing the images anymore or something like this ?
How to recover the boot loader, so i will be able to install again WM 6.1 r3 ?

add
I need additionally information about a software for low level analyzing debugging of Pocket PC's or low level settings, boot loader settings low level screen resolution settings.

i have tried to install wm 6.1 on my eten m600 ,
but after booting on block 3623,
it said ok.
and restarted
now it goes orange screen and after some moment it goes white science .
plz help me to make on my eten m600

Artemis help

hi boss i have problem with my ARTEMIS after unlocking it the screen goes black and goes off i need help to solve this problem pls thanx in advance

artemis help
i m new to this site i just flashed my p3300 with bad cooked rom now it close. it wont boot it stuck in boot screen and one of the main thing is there is no OS .... symbol on bootscreen only showing IPL SPL GSM when i press and hold record and power + reset it wont go to bootloader how can i enter in to boot loader plzzz hel me ,
im awaiting for any one reply
if someone help that greatfull for me
plz help me

...
robinzen said:
i m new to this site i just flashed my p3300 with bad cooked rom now it close. it wont boot it stuck in boot screen and one of the main thing is there is no OS .... symbol on bootscreen only showing IPL SPL GSM when i press and hold record and power + reset it wont go to bootloader how can i enter in to boot loader plzzz hel me ,
im awaiting for any one reply
if someone help that greatfull for me
plz help me
Click to expand...
Click to collapse
* if you have an SD card in the device, take it out..
* put these two .cab files on your device and run them..
- Cert_SPCS
- EnableRapi
* get activesync connection to pc..
* start_uspl.. (runs a dos window on pc)
* screen on phone goes blank.. or penguin picture..
* only when the rom update utility window opens on pc, soft reset when its 100%..
(to get new activesync connection)
* continue to run rom update utility..
***ONLY after doing uspl is it safe to flash a rom..
when you have done uspl on your device startup you will see..
SPL: 1.11.cmon
* its done.
now flash any rom to your device..
USPL 1.11.CMON here.........
http://forum.xda-developers.com/attachment.php?attachmentid=41246&d=1181558635
***you have bricked your device so read carefully...
you MUST flash you device with the official rom before uspl..
you can find your official rom here...
wiki.xda-developers.com/index.php?pagename=Artemis_Upgrades
flash with official rom and message back wen you have done it --- only the official rom will work on a bricked device.. --- for now..
message me if you get stuck dude

Artemis Loadboot

hi, everyone, i have one artemis but this pda doesn't pass the load boot window, i have try the hard reset and it won't pass for windows... so, i can't syncronise the phone with pc to put a new rom, plz help!!

soft restart , when the screne is out ...then press power&voice button at the same time,
then u can see three colour ....after that insert u usb cable..... now u can flash your PDA....GOOD LUCK.

dear friend, the three colour menu apears and the pc recognize the pda, but in the RUU instaler, apear error code #260 (update error).
i try the artemis USPL to free the CID...
with Shady 313 ROM, the error is #260 (file open).
plzzzz with my diamond this process is very easy :S i'm broken my head with this pda model

SOLVED tks