Develop Bugs

Htc P3300 Bootloader Problem !!!

Hello Everyone. I Am Trying To Istall The Official Wm06 But The Bootloader Does Not Respond. Any Sagestions Pls

U give us very little info to respond to
what pc system r u using? What version activesync, what exactly happens (or doesnt), which rom/language, did u cid unlock it (used uspl), etc.
Be more specific please.

Twiggerdingo said:
U give us very little info to respond to
what pc system r u using? What version activesync, what exactly happens (or doesnt), which rom/language, did u cid unlock it (used uspl), etc.
Be more specific please.
Click to expand...
Click to collapse
hello again.thanks for the responce. my p3300 has the official wm5. i load the
wm06 (not official) one of the programs that i use in my job dosn't work propertly. so i have to restore in previus wm5. i download fro the site of htc the official wm6. in htc they told me that it is very easy so i could do it my self. i had only to conect the usb cable to the pc (windows xp) and run the file (wm6) i did it but when it start to install the wm6 the activesyng (ver 4.5.0) shut off and stoped the instalation. the screen turn to black. after that the p3300 started again but when i push the voice key and the power key to get in to the bootloader it doesnt work the screen becams to a multi color pixel.the htc told me that i have to replace all the inside hardware. thats all thanks a lot .

robinbatman said:
hello again.thanks for the responce. my p3300 has the official wm5. i load the
wm06 (not official) one of the programs that i use in my job dosn't work propertly. so i have to restore in previus wm5. i download fro the site of htc the official wm6. in htc they told me that it is very easy so i could do it my self. i had only to conect the usb cable to the pc (windows xp) and run the file (wm6) i did it but when it start to install the wm6 the activesyng (ver 4.5.0) shut off and stoped the instalation. the screen turn to black. after that the p3300 started again but when i push the voice key and the power key to get in to the bootloader it doesnt work the screen becams to a multi color pixel.the htc told me that i have to replace all the inside hardware. thats all thanks a lot .
Click to expand...
Click to collapse
Ok, let me see if i understand u correctly, your specs give me no new questions they look ok. U have WM5 and want to run a program (from your work) which needs WM6 (wont run on WM5). HTC told you about the official WM6 update. This wont flash as activesync crashes, right?
With an official Rom you will not need to unlock the CID/SPL with USPL. But this goes only when you stick to your current language. i.e. a german WM5 is not allowed to be flashed into english. To do this you will need to USPL-unlock it 1st.
If the language is the same, it should work. Best is to do a hard reset 1st (2 soft buttons and soft reset, wait and press green/send.) Afterwards hook it on the PC (activesync want to start a newe partnership, click cancel, so u will be connected as guest).
Start the rom upgrade. Activesync should close and bootloader on the ppc will be started. This is a screen with many colours/stripes, which is normal but looks very bad and different from normal bootup.
Then the flashing will start, the screen on the ppc will turn white/grey and a scale will show you the percentage of the flashingprocess (similar to the screen of the pc). Wait patentiently and do not toch the ppc or disconnect (or expect a bricked device).
At the end, the ppc will reboot and take a while (longer then normal bootup) to initiate the boot for the 1st time.
If this wont work, then try to extract the upload file, put the ppc in boatloader mode, connect to pc and start the romupdateutility.exe directly.
Good Luck!

hi,
i've flashed my HTC P3300 and it was done successfully (using USPL) but the language was Spanish, i searched a lot how to change it to english since i dont understand a word of it.
through one of the forums, i was told to set the SysLang = 1032 in registry to get the english language, i done so, now, the phone is stuck in Welcome (WM6.1) screen and nothing is happening, not even responding to power key.
I tried hard reset, it doesn't work, i tried entering to bootloader, it also doesn't work, also, i am not able to connect it to PC since i guess its not completed up.
Just got stuck with a brick, can you help please. Really needed!!!!!!
Thanks

Maybe flashing ROM from memory card may help. Search Artemis wiki for micro card ROM flashing.

Hello, I guess I'm having the same problem...tried to flash but something went wong and now I have my htc p3300 blocked with the multicolor screen. It does not work, so I don't understand how I could start flashing rom by memory card. Could you be a little bit more detailed? Thanks in advance

Guys, need hlp. Eten m700 not starting.

Hello everyone.
I do have some experience with rom modifications on my I-mate Jam, but this was the first time I tried to change my m700's rom.
Things I've removed from my rom (pretty fearsome):
-------
OEM\OEM_Lang_0409
blank.pwi
meeting.pwi
memo.pwi
phone.pwi
todo.pwi
OEM\OEMDrivers
Avrcp_MPplugin.dll
SYS\BaseApps\
-ApproveUpdate\
-AUTOUPDATE\
-Autoupdate_Lang_0409\
-caldll.dll\
-calendar.exe\
-calnot.exe\
-calstore.dll\
-calupd.exe\
-fexplore.exe\
-hotvoice.exe\
-idledetect.exe\
-notes.exe\
-pimapi.dll\
-pimdlg.dll\
-pimg.exe\
-pimgdll.dll\
-pimgres.dll\
-pimstore.dll\
-taskdll.dll\
-tasks.exe\
-calc.lnk
-calendar.lnk
-MobileCalculator.exe
-notetake.lnk
-pimg.lnk
-tasks.lnk
SYS\Browsing\
SYS\Browsing_DPI_96\
SYS\Catalog\
SYS\Catalog_Lang_0409\
SYS\Entertainment\
SYS\Entertainment_DPI_96\
SYS\Entertainment_Lang_0409\
SYS\Entertainment_Lang_0409_DPI_96\
SYS\FWUPDATE\
SYS\Fwupdate_Lang_0409\
SYS\IRDA\
SYS\IRDA_Lang_0409\
SYS\MediaOS\
SYS\MediaOS_Lang_0409\
SYS\MediaOS_resh_240_resv_320\
SYS\Office\
SYS\Office_DPI_96\
SYS\Office_Lang_0409\
SYS\Office_Lang_0409_DPI_96\
SYS\Os\
-ircomm.dll (only!)
SYS\Shell\
SYS\Transcriber\
SYS\Transcriber_Lang_0409\
SYS\Transcriber_Lang_0409_DPI_96\
SYS\WindowsLive\
SYS\WindowsLive_DPI_96\
SYS\WindowsLive_Lang_0409\
-------
I didnt modify my registry, cause I thought it will give errors, but the rom will still be working. I was going to clean up non existing keys with sktools.
I've packed my rom back, everything went ok.
I've uploaded rom to my eten m700 via usb. Again everything was ok.
Then I've made a hard reset (after the installation) and the device booted (the screen was orange). But nothing happened after. The device froze.
_______
Could it happen becouse I didn't remove 'today plugins' in a registry?
Or some programms are hardcoded to wince, so u just cant boot without them?
-------
Oh yes, ActiveSync doesn't see my device. I've heard it is possible to start usb sync from the knight mode. How do I do it?

press the camera button and screen off button together. reset the cellphone while still holding the two buttons. it will go to dark mode

Thx for the tip.
In test mode, I've found out that my Os image checksum is smaller. So I'd probably add irda dll back. I'll also remove all today plugins in registry settings to make sure the os can boot properly.
------
Here comes the question!
I enter the bootloader mode on my device. It says USB host is connected. Waiting a download.
But my activesync doesn't see the device... And when I start upgrading the device here what comes out:
Can't connect to the device. Please make sure ActiveSync is working normally.
How do I fight this? I don't have a sd card yet...

[Solved]
Yes, there is a trick! Thx to Юрка, from 4pda.
U just need to plug any other communicator (wince) to the cord, start the updater. When it comes to the download (black pic apears to the left, saying smth about download)
-put your nonworking device in a bootloader mode (hold down turn on/off button + recorder button and push restart, then release power button, but still keep holding the recorder button)
-unplug ur other device from the cable
-plugin the eten nonworking device
click upload and after everything went well - ENJOY!

Bootloader Mode on XDA Stealth

Dear All,
I'm stuck at align screen on this XDA Stealth, and guess I need help from you people.
How can I enter Bootloader Mode on XDA Stealth? ( I can enter engineering mode, but can't see any option to enter Bootloader i.e. tri-color screen).
I'm unable to upgrade ROM on this device because of the following reasons.
1. I upgraded WM6.1, and found that Active Sync won't work unless patched.
2. The display's touch screen is defective so after up ROM Upgrade, I'm stuck at align screen, further, the phone is not getting detected in windows as there is this patch required for the ROM.
3. I don't have miniSD reader and also I don't think the car works properly.
So, is there any way to enter the bootloader mode and get the device detected under windows so that I can upgrade again?
wbr
Sonny

xda stealth - Q.? = remove battery and the model is htc??????????????
WIKI
engineer mode ???
6.14wm - O2 pre-pay

Hi,
This ain't HTC, it specifically says Model : XDA Stealth. Guess the Manufacturer is Gigabyte. Although, Gigabyte is not mentioned anywhere on the back.
Engineering Mode is accessed by pressing Power + Camera + Flag keys while boot up. The Screen Displays GIGABYTE Communications P.O.S.T. and in Main Menu, there are various tests and configurations.
What I'm looking for is a way to upgrade the rom by getting the phone detected in Windows. Is there any way to get bootloader mode on this phone?
Thnx
Sonny

HP Ipaq 614 stuck in bootloader mode

Hello
My HP Ipaq 614c pda stuck in bootloader mode. I was used different modes (different button combination): clean boot, format, download mode. Result is the same: After this operations , PDA stops/stucks and the blue hp logo is displayed.
Could you help me and give me some alternatives?
See you
Krabat

krabatxda said:
Hello
My HP Ipaq 614c pda stuck in bootloader mode. I was used different modes (different button combination): clean boot, format, download mode. Result is the same: After this operations , PDA stops/stucks and the blue hp logo is displayed.
Could you help me and give me some alternatives?
See you
Krabat
Click to expand...
Click to collapse
Did You tried to reflash the ROM?

Yes, I used:
- mtty but this soft doesn't see usb (not allowed usb in Activesync, kill some process in task manager)
- dnw is not working because the followed error is displayed "can't write dnw.ini"
So situation is not changed. Unless you know good reflashing program.
Hey

Hi
I hawe same problem with two old HP614c devices.
Can hellp with some info about repair them Bootloader software.
I think is necessary special cabel for koading new bootloader software into chip, or have same programs for that ?

http://forum.xda-developers.com/showthread.php?t=459123
too old thread of mine, but hope it will work.

to stupid to read - need help

Hi!
What I have done:
-got a rom which fits to my needs
-downloaded it, renamed it to DIAMIMG.NBH, transfered it to my internal storage
-put the phone into bootloader mode, used MTTY all went well
-boot again... freeze
-initialising rom .... freeze
-trying custom_ruu.exe .. freezes at 0%
-hard reset.. fine, boot.. freeze
-finding the thread about MTYY reading that I should have Hard SPL.. swearing a lot
Is there any possibility to get my phone running again? As far as I have found no info how to install anything without a running sync connection, but without any system on the phone I dont know how to establish any connection other to the bootloader mode

Because you haven't upgraded HardSPL before flashing new custom rom - I think you did brick your phone.

Hello, prl3st
I have solition if you use htc touch diamond ( diam 100 ) but if you did not model HTC Diamond, can go try it.
A possible solution could be:
- Obtain a functional ROM (file that RUU_signed.nbh) interface CustomRUU.exe
- Connect the phone cable to the PC
- CustomRUU.exe starts and pass the first two screens where you wondered if you connected the device and that he give the order to enter in flash mode
- On smartphone: press volume down and reset simultaneously to get in the boot mode. Once you made that follows the instructions on screen.
Possibly if it fails the first step to obtain a version of HardSPL Diamond, copy the file there. Nbh and running ROMUpdateUtility.exe phone connected to PC and a loader.
It should work. Good luck and more attention next time.

yep worked fine with the original ROM from HTC!
Thanks to XDA developers and big thanks also to awran5 who gave me some privat support =D