Qtek 9090 Stucks in Upgrade Mode - MDA III, XDA III, PDA2k, 9090 General

Hi to the list,
i own a Qtek 9090.
Today i tried to upgrade the ROM but while it was upgrading i got the
ERROR CONNECTION
and the Qtek stucks in the Upgrade Mode.
I've tried to reset the Qtek also with an hard reset but it always starts in
Upgrading mode and do not connect to the Home PC any more.
Is there anybody which can tell me how to get out that mode and return in normal mode?
thank's in advance.
Enzo.
[email protected]

Look at these pages.
http://wiki.xda-developers.com/index.php?pagename=BA_1.40.00_Upgrade
http://wiki.xda-developers.com/index.php?pagename=BlueAngel_For_Beginners Section 3

Related

Rom Upgrade Problems

Hi, I have upgraded my Qtek 9000 Rom WWE with a PTB version.
Now, my phone only show the "USB v1.0" screen...
Is the 4th time that i'm trying to do this again, and it still doen't boot up to the Windows Mobile, only the "USB v1.0" screen.
I have tried hard resets and it still on "Serial v1.0" screen...
Please someone help me!
http://forum.xda-developers.com/viewtopic.php?t=43592
Worked using a diferent radio Rom. Thanks.

How Turnoff Bootloader Mode

I have upgrade my universal to wm6 rom 2.10.02 wwe and now i can`t turn off bootloader mode;(
after hard reset and soft reset device always turn on bootloader mode and dont start system what can I do??
Use: uni_exitbootloader.zip
You can find it : ftp://ftp.xda-developers.com/Universal/Tools_and_Programs/
sorry first time i`ve got problem with upgrade I do this for long time
i was so sad that I forgot about WIKI

ipaq hx2410 help

I have a problem updating my bricked ipaq hx2410(wm2003 se). I'm stuck at the pre-B.L screen. When i ran the rom update, i'm getting the incorrect language! update cannot continue. I tried to reflash windows mobile 2003 se, the progress bar stops at 0.1%, then upgrade was successful .
upgrade Needed: Version 1.00.00 L Language: english, model ID: ipaq hx2xxx
cuurrently Installed: Version "blank" Language: Unknown, model ID: ipaq hx2410.
I also tried the bootloader and getting a blank mtty. Can someone explain to me step by step how to fix this.
Is there anybody that can help me with this problem or redirect me to a link
I had a similar problem with my HX2790 running MW5. I avoided the problem by running the official ROM update for my language. If you run it in normal mode (not pre-BL mode), somehow the software will recognize the correct language, switch to pre-BL mode by itself and will ask you to update or cancel. At that point, if you want to upgrade to 6.1, substitute the nfb file of the ROM upgrade by the WM6.1 otherwise just do the ROM update.
This suggestion might not be relevant as in my case, the ROM version was detected correctly. In your case, the version is blank. I think you should read the whole discussion http://forum.xda-developers.com/showthread.php?t=383173. Many suggested ways to recover a failed upgrade.
Best luck
Varso
The only way to turn on my ipaq is through the hard reset, otherwise i get a black screen. Is there a trick to turn it on using the normal mode?
Is there any way to bypass the language check? Is my ipaq dead. After i flashed it with AKU,the screen went black at the end of the upgrade(turned off at 100%). Please help.
Thanks for the link. It worked
Varso said:
I had a similar problem with my HX2790 running MW5. I avoided the problem by running the official ROM update for my language. If you run it in normal mode (not pre-BL mode), somehow the software will recognize the correct language, switch to pre-BL mode by itself and will ask you to update or cancel. At that point, if you want to upgrade to 6.1, substitute the nfb file of the ROM upgrade by the WM6.1 otherwise just do the ROM update.
This suggestion might not be relevant as in my case, the ROM version was detected correctly. In your case, the version is blank. I think you should read the whole discussion http://forum.xda-developers.com/showthread.php?t=383173. Many suggested ways to recover a failed upgrade.
Best luck
Varso
Click to expand...
Click to collapse

My SPV M3100 bricked, can anyone help me?

Hello, I was re-flashing my SPV M3100 (with hardspl v7 oplio 2.10) from Schaps WM6Pro_Hermes 4.30 WWE Full Rom to the 20070311 Hermes WM6 LVSW rom, at about 22% of rom being updated, the USB cable was accidently unplugged from my device
I plug it back up and try to restart the process but it gives me a "ERROR [260] UPDATE ERROR" message and my PDA screen stays at windows mobile and my Activesync 4.5 can't connect to my PDA
When I try Soft Reseting or Master Reset, it will try to load and I see red letters on the HTC boot
M 05
S 04 NO GSM (appears for about 8 sec.)
B 06 D 3.62
After the red words clear and it stays frozen on the windows mobile screen. Can someone please help me..
put the phone into boot loader and try flashing the rom again.
Hi Joshkoss,
I have tried many times re-flash the rom and sim unlock under bootloader, however all doesn't work at all.
IPL: 1.01, SPL: 1.09.
Could you please kindly advise?
Thanks in advance..
try the stock shipped rom from bootloader, maybe it will "see" it.
It looks like you do not have hardspl v7 installed. With hardspl your spl line should say 2.10 olipro
You need to flash the original orange rom to your spv m3100, what country you are in is important, if in the uk use the rom update from orange on there website, if any other country then use that update.
hey guys, thanks alot for your advice.
cheers..

Urgent help: HTS P3300 stuck up

Dear All,
Please urgent help required.
my HTC P3300 (Artemis) stuck up when i was trying to start it up. when i use to turn my cell on, i goes to the starting screen shows the following numbers and then stuck up.
IPL 3.07.0001
SPL 3.07.0000
GSM 02.69.90
OS 3.7.0.0
the screen does not move after that. i tried soft reset through the reset button but result is the same.
i also tried hard reset and when i puch the green phone button to proceed, a message come "FORMAT FAILED" and the phone stucks up.
i am quite a lot of problems since i have upgraded to WM6 from WM5 last week.
i am quite sucked with this problem. not been able to use my set since yesterday.
please also note that my HTC was not syncing with my PC since i have upgraded to WM6.
PLEASE HELP URGENTLY.
Nomi
HTC P3300
Follow this link and have a deep read
http://wiki.xda-developers.com/index.php?pagename=HTC_Artemis

Categories

Resources