I have a problem updating my bricked ipaq hx2410(wm2003 se). I'm stuck at the pre-B.L screen. When i ran the rom update, i'm getting the incorrect language! update cannot continue. I tried to reflash windows mobile 2003 se, the progress bar stops at 0.1%, then upgrade was successful .
upgrade Needed: Version 1.00.00 L Language: english, model ID: ipaq hx2xxx
cuurrently Installed: Version "blank" Language: Unknown, model ID: ipaq hx2410.
I also tried the bootloader and getting a blank mtty. Can someone explain to me step by step how to fix this.
Is there anybody that can help me with this problem or redirect me to a link
I had a similar problem with my HX2790 running MW5. I avoided the problem by running the official ROM update for my language. If you run it in normal mode (not pre-BL mode), somehow the software will recognize the correct language, switch to pre-BL mode by itself and will ask you to update or cancel. At that point, if you want to upgrade to 6.1, substitute the nfb file of the ROM upgrade by the WM6.1 otherwise just do the ROM update.
This suggestion might not be relevant as in my case, the ROM version was detected correctly. In your case, the version is blank. I think you should read the whole discussion http://forum.xda-developers.com/showthread.php?t=383173. Many suggested ways to recover a failed upgrade.
Best luck
Varso
The only way to turn on my ipaq is through the hard reset, otherwise i get a black screen. Is there a trick to turn it on using the normal mode?
Is there any way to bypass the language check? Is my ipaq dead. After i flashed it with AKU,the screen went black at the end of the upgrade(turned off at 100%). Please help.
Thanks for the link. It worked
Varso said:
I had a similar problem with my HX2790 running MW5. I avoided the problem by running the official ROM update for my language. If you run it in normal mode (not pre-BL mode), somehow the software will recognize the correct language, switch to pre-BL mode by itself and will ask you to update or cancel. At that point, if you want to upgrade to 6.1, substitute the nfb file of the ROM upgrade by the WM6.1 otherwise just do the ROM update.
This suggestion might not be relevant as in my case, the ROM version was detected correctly. In your case, the version is blank. I think you should read the whole discussion http://forum.xda-developers.com/showthread.php?t=383173. Many suggested ways to recover a failed upgrade.
Best luck
Varso
Click to expand...
Click to collapse
Related
Hey iam new to this upgrading,CID unlocking etc.
I just bought my Cingular 8125 three weeks before.
I tried upgrading to WM 6.0 The update process completed successfully but after the reboot my mobile was back to factory default with wm 5.0.
without tring the lokiwiz to unlock, i used shelltools to flash the wm6.0.
it was successful, it asked me to do a hard reset.
Since then i am stuck up with the boot screen.
I can't get my Mobile back working.
i tried flashing with the Offical rom but of no use.
i have tried button rom, love rom. nothing works out.
without much knowledge i upgrade my spl & IPL to 3.08
now i am not able to downgrade that too.
tried flashing different roms but of no use, still it stucks up in the boot screen.
the only hope iam having is i am able to get into the boot loader.
I am not sure, where to post this thread, my appologize if i have posted in the wrong page.
below is the information i have on the screen
IPL 2.26
SPL 3.08
GSM 01.12.10
OS 1.5.4.2
Some one please help me out. i am very much worried, any help is very much appreciated.Thanks a bunch in advance !
dosai.
Have you tried flashing from the bootloader to an official rom?
thanks for reverting, i have tried that too, but of no use.
Sounds to me like you didn't run the Cert_SPCS and EnableRapi cab files before flashing with ShellTool. Being stuck at the splash screen is a dead giveaway.
I never did understand why someone would attempt to flash a ROM without doing ALL the steps. . .
i did ran Cert_SPCS and EnableRapi cab before running the shelltool. shell tool took around 10 mins to complete the update.after restart, my phone stucked up in the boot screen!. (i remember not unlocking the cid before proceeding with the shelltool) .
is there any way to get the mobile working i am too worried.
Solution
Hi, press and hold the CamShot Button and press the Power button, when you see a multi-color screen you can make a update again.
Hello all Im new here and have the same problem. I followed all the steps and followed all the instructions to fix this problem but nothing. I am stuck on the multi-color screen and i can't do nothing! HELPPPPPPPPPPPP!
Hi everyone, I've downloaded the WM6 for portuguese language for my HTC P3300. When I try to install after the coloured screen appears, percentage count starts until 2% and then the device soft-resets itself. Has anybody experienced something similar...? I tried to enter bootloader and upgrade again but it also failed. Then I tried a hard-reseta and also failed. I don't know what else to do.
are you using Vista?
have you read the forum ? and launch start_uspsl before ?
After an successful rom upgrade from win 2003 se ITA to wme5 eng AKU 3.5.2 i`ve got my hx2750 dead.
The only thing that i can do is contact+itask + reset and got o Pre-BL: 1.00.02 screen. i tried original hp update/ patched update / universal bootloader/mtty and host11 without any results. hp update / patched update giveme succesful update after 2 sec then shutdown my ipaq. With mtty i can connect with my ipaq but i don`t have any prompt just flashing cursor. With universal bootloader it start and do nothing. And last host11 give me lost usb connection after 1 second. I tried to contact hp and they ask me 280$ for a motherboard change... crazy!!!
Is there any chance to remove my ipaq from trash and give it a second life??? any ideas?help?
Thanks very much
Abs.
P.s. sorry for my english
I see you posted in the thread I had going with a similar problem - unfortunately, I have no other solution than swapping with a second device - on the brighter side - if you purchase one and fix the other one, you can probabley resell one of them for around what you paid for it
Good luck!
It`s not easy to find a used device in italian.. Btw i`ve got a little update.
Now i`m able to flash wme5 original / Aku / and wm6. But i have another problem.. flash process are ok.. on first reboot my ipaq start and at 30% of startup process shutdown... i will work on it..
Abs
good luck and share your experience.
Ok, well if you're able to get it to flash - try flashing back to 1.00.00.L - should boot then. Worked for me - so give it a shot.
I had to reflash to the original rom (no boot, but able to successfully flash in bootloader) - then to 1.00.00.L (boot and hard reset) - then to 1.00.00.H (boot and hard reset) - then to 1.00.25.H (boot and hard reset) - then to WM6 (boot and hard reset) to get everything to work after mine was bricked.
Oh, and if you DO use another device - it doesn't have to be the same language as the original - just swap to the correct file/language at the appropriate time in the flash.
hi plz every one who can help me it very urgent..
i try to upgrade my friend htc hermis but i am stuck in os menu
previusly i install scap rom 3.3
i treid to install the new version it reached 2% and the an error massege appear (connection error) then i tried to do it again but evry time i try the same maasege appear on the phone (coonection error )
it reach 0% and this message appear
i have spl 1.09
i also tried to hard spl it but still the same message ...
i treid different usb and pc but still
i download an official rom the same message
i sleep a see the same f*cking message
plz help me
IT Would help if you Gave the Error Message # for Example If your Getting Error Message 240 It's a Connection Problem.
Try Turning of your Firewall, Have the Rom you are upgrading to in your Root Directory And Always Make sure your Phone is Super CID unlocked.
Hope This Helps.....I"ve been where you were at once... IT was the My Firewall for me.
Try flashing your Operator rom using the SD card method. Or looking at the Unbrick table done by POF. It's all in the WIKI...
halder said:
hi plz every one who can help me it very urgent..
i try to upgrade my friend htc hermis but i am stuck in os menu
previusly i install scap rom 3.3
i treid to install the new version it reached 2% and the an error massege appear (connection error) then i tried to do it again but evry time i try the same maasege appear on the phone (coonection error )
it reach 0% and this message appear
i have spl 1.09
i also tried to hard spl it but still the same message ...
i treid different usb and pc but still
i download an official rom the same message
i sleep a see the same f*cking message
plz help me
Click to expand...
Click to collapse
Try booting in debug mode (hold the Side OK button + power button and reset at the same time)
once you booted into that 4 colored screen with SPL/IPL listed, flash the device with HardSPL 0.7
Link Here
Then upgrade your device again.
using HardSPL it ensures your device will not be overwritten with bad blocks and it enables unsigned rom files to be written to the phone. it's a win-win if you upgrade it.
still the same message 262 update error.
i triecthe hard spl but s6s error always appear
i can go to boot screen
plz if there solution tell me..
its not afirewall fault..
halder said:
still the same message 262 update error.
i triecthe hard spl but s6s error always appear
i can go to boot screen
plz if there solution tell me..
its not afirewall fault..
Click to expand...
Click to collapse
This 262 Error Message I got this
""ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.""
At this Point I"m Stumpped I"m hoping one of the Big Boys Will Step in on this one and give you a better Solution....
yes it reached 2% then it stuck there i treid to reupgrade with the same rom no luck..i tried different rom also ..
do u think if i download a shiped htc rom it will work
halder said:
yes it reached 2% then it stuck there i treid to reupgrade with the same rom no luck..i tried different rom also ..
do u think if i download a shiped htc rom it will work
Click to expand...
Click to collapse
Wam7 has already given the best advice to start unbricking your phone.
1. Get the original Rom which came with your phone. It might be listed here http://wiki.xda-developers.com/index.php?pagename=Hermes_Upgrades or here http://wiki.xda-developers.com/index.php?pagename=Available Original Shipped WM6 ROM Versions. If it is not listed you'll need to search the internet and/or this forum.
2. When you have your original ROM, flash it to your phone from the SD card, not from your computer. Instructions to do this are here http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing. Remember to have a full battery charge before beginning.
Hopefully this will recover your phone. If it does, then make sure that you flash Olipro's HardSPL 2.10 (V7) to your phone http://forum.xda-developers.com/showthread.php?t=296722.
If you get stuck on how to do this correctly, there is some good advice in Mrvanx's upgrade guide http://forum.xda-developers.com/showthread.php?t=299462.
Also, in the future it can help others to help you if you give more information about your phone such as phone type, original ROM, current Rom, Radio version, SPL version etc, etc. Most people include some of this info in their signature so they don't have to keep re-typing it.
thank you very much for replaying...
i tried the sd card method and i download my exact cid rom but still it give the error 0068002 i download more than 5 original shiped rom same message
my phone is htc ...tytn ..not qtek or dopod ....
htc pure
info
r 1.18.00.10
g 32.55.7018.01h
d 3.57
m05 s04 b06
any other solution
i can go to boot menu
plz again
i tried evry possible way to flash my phone but i cannt get it done why??? EROOR 262
i download more than 10 official rom (htc) and i apply the exact sd method steps still it give me 0028002 error
my device is HTC ...BUT HTC WHAT I DONT KNOW...IT JUST HTC ONLY
SO I CANNOT CHOOS MY EXACT CID ROM
PLZ HELP ME OR I WILL THROUGH IT AWAY
plz answer me its very urgent?????
ok i dont want to open a new thread with same question.so if some one plz can help i will be graetful....
i want to knew how to fix error 262
Have you tired flashing from the bootloader?
Have you tired flashing just the rom from mitty ?
Is the phone unlocked? Have you thoroughly read the unbricking thread in the wiki?
WB
i dont know if its unlocked but i flash it with chap 3.7 a then i tried to flash it with chap 4.00 it reach 2% and stoped..ofcouse its unlocked..
it tried the mitty way but it give
level=ff instead of 0
and bad command
it tried the sd card method the error 0068002 or invalid vender id
If you get invalid vendor error doesn't that mean the phone is locked?
since no one helped me here in this thread ...i helped my self..
i found the solution...i send my ID to htc.com and they replay nicey and send me the link to my exact cid rom ..
the problem was my original rom was norway not wwe ..**** who thought that???
anyhow thank you for all who tried to help me..really i benfit from thier method for future desaster???
see u in another problem...
cuz we know nothing we just ask and ask until we find the solution ..
Hallo to everyone. I am a new on this forum, sorry if I ask question on wrong place.
I have HTC P3300, black&blue. Last few months it started to freeze and restarts with no reason. I attempt soft reset and it worked. But a few days ago I couldn't start the phone. There is no charge indicator when I plug in charger. In one word DEAD. A few times I tried full reset but is not working. After the formatting it freezes and goes on same way (dead).
I also tried to flash it from sd card it shows "Invalid certificate". When I try to flash it from the computer I receive "ERROR [294] : INVALID VENDER ID". Probable I'm trying to flash with wrong .NBH file. How to find appropriate rom file?
Just to add, I have problem to call bootload mode. I have to try few minutes to succeed that.
Its ARTE 100, black&blue IPL 3.13.0001 SPL 3.13.000. Last time I had windows mobile 6.1 in English.
If anybody had same problem, or can help on anyway, please help me. Thanks in advance.
maxbojan said:
Hallo to everyone. I am a new on this forum, sorry if I ask question on wrong place.
I have HTC P3300, black&blue. Last few months it started to freeze and restarts with no reason. I attempt soft reset and it worked. But a few days ago I couldn't start the phone. There is no charge indicator when I plug in charger. In one word DEAD. A few times I tried full reset but is not working. After the formatting it freezes and goes on same way (dead).
I also tried to flash it from sd card it shows "Invalid certificate". When I try to flash it from the computer I receive "ERROR [294] : INVALID VENDER ID". Probable I'm trying to flash with wrong .NBH file. How to find appropriate rom file?
Just to add, I have problem to call bootload mode. I have to try few minutes to succeed that.
Its ARTE 100, black&blue IPL 3.13.0001 SPL 3.13.000. Last time I had windows mobile 6.1 in English.
If anybody had same problem, or can help on anyway, please help me. Thanks in advance.
Click to expand...
Click to collapse
Hi Bro,
I think you need to first get the original ROM installed. There is a process mentioned in ELfin section somewhere to idetify which ROM is your original rom. Once you have the orginal ROM up, then refer to CID/USPL unlocking before flashing any other ROM.