Help me Qtek 2020 to WIN 2005 - Upgrading, Modifying and Unlocking

upgraded Qtek 2020 to WIN 2005 (ROM 1.50f) and everything worked fine.
Then I downgraded to version 2.20. Installation went normal, but after the installation and hard reset, the Qutek didn't run, but just writes the next text:
Device authentication failure. Please contact the product manufacturer. For reference, please provide your device ID.
6000222100391951 38000050bf3f5173
When I reset it, it stil writes that the operating system is still 1.50f.
I tried with another qutek to downgrade, but the the computer doesn't recognize my Qutek.
Can somebody help me with this, how should I solve this problem.
I also tried with next procedure:
1 Power Button
2 Record Button
3 Camera Button
4 Soft-reset Button with Stylus
etc. etc.
PC becomes aware of Qutek, but the installation doesn't work.
Is there any possibility to perform hard hard reset, so that it would be withouth any operating system. That it would be completly clean.

Related

-==Qutek 2020 DEAD==-

upgraded Qtek 2020 to WIN 2005 (ROM 1.50f) and everything worked fine.
Then I downgraded to version 2.20. Installation went normal, but after the installation and hard reset, the Qutek didn't run, but just writes the next text:
Device authentication failure. Please contact the product manufacturer. For reference, please provide your device ID.
3065782000381951 38000050bf3f5173
When I reset it, it stil writes that the operating system is still 1.50f.
I tried with another qutek to downgrade, but the the computer doesn't recognize my Qutek.
Can somebody help me with this, how should I solve this problem.
I also tried with next procedure:
1 Power Button
2 Record Button
3 Camera Button
4 Soft-reset Button with Stylus
etc. etc.
PC becomes aware of Qutek, but the installation doesn't work.
Is there any possibility to perform hard hard reset, so that it would be withouth any operating system. That it would be completly clean.

I upgraded Qtek 2020 to WIN 2005

I upgraded Qtek 2020 to WIN 2005 (ROM 1.50f) and everything worked fine.
Then I downgraded to version 2.20. Installation went normal, but after the installation and hard reset, the Qutek didn't run, but just writes the next text:
Device authentication failure. Please contact the product manufacturer. For reference, please provide your device ID.
6000222100391951 38000050bf3f5173
When I reset it, it stil writes that the operating system is still 1.50f.
I tried with another qutek to downgrade, but the the computer doesn't recognize my Qutek.
Can somebody help me with this, how should I solve this problem.
I also tried with next procedure:
1 Power Button
2 Record Button
3 Camera Button
4 Soft-reset Button with Stylus
etc. etc.
PC becomes aware of Qutek, but the installation doesn't work.
Is there any possibility to perform hard hard reset, so that it would be withouth any operating system. That it would be completly clean.
I need win 2005 for i-mate pocket pc or xda ii or qtek 2020
I need win 2005 for i-mate pocket pc or xda ii or qtek 2020 PLZ help Me

It's dead... terminal get device data error

Hi
just tried to upgrade my ROM on the O2 exec. It's a brand new machine. Followed the instructions, but I received a 'get device data error' message and now my 02 exec is dead. I've tried soft and hard resets, holding down the power + reset, power+backlight+reset, removing the SIM & battery etc etc. No life. If I do a hard reset, I see a screen asking to press 0 for factory defaults or x to exit - I've tried both to no avail. Any suggestions?
Thanks
signs of life...
Just followed some tips on this forum regarding the MAUpgradeUt_noID utility and it is currently upgrading it's radio stack... so it looks like I will have signs of life here... perhaps now I should change my username cause I'm not confused anymore... thanks to all those who posted previously...
Success through a different route - O2 users please read
OK, I may be a dumba55, but I could not get the previous method to work. I downloaded the current O2 ROM, unzipped it using WinRAR, then ran the program ROMUpgradeUt rather than the previously suggested MaUpgradeUt_noID, which I tried twice but the device would not leave the bootloader screen. I then performed a hard reset (holding the two - keys below the screen and depressing the reset button) and wallah... it's back alive again. The funny thing is O2 actually sent me a replacement unit because of this problem previously... :lol: thankyou O2 from a dumba55.

Help! Brothers. I get a brick i600!!

Help!! Brothers
I have tried to update my i600 to wm6 with a flashing program named "I600_WCEDownloader_v1.1_Single" and 3 update files extracted from the official update patch. I downloaded them from MoXXCo.
For the first attempt, around the end of the process, it took a quite long time without any response. I then unplug the battery for another reset... it held at the screen showing "The Ultra messaging". Then, I tried one more "flash" but the update hung up at the end also.
I have no choice but try to re-flash it with the GD1 and GA2 roms. However, during the updating "Phone" part, the phone screen shows the following messages.
[Phone] Active OFF -> Active OFF
[Phone] Reset Pin -> Low : OFF
*[PHONE] Phone Download Failed!
My phone does not have the phone function right now. I find that the Phone version is only blank in the "Version" page, but the eboot and PDA version is shown there. Is there any solution I can do to fix the problem??
I find one more thing but is not sure if it is related. if I do the reset when I go to "Settings" -> "Security" -> "Reset" , and try to hard reset the machine, it fails. Besides, I find that there are three reset options under the "internal" menu, it failed to reset the machine as well.
However, if I use the most common reset method. I switch off the machine and reset the machine by pressing "4-way navigation key UP + Power" simultaneously. After the phone prompts for reset, press 1 and then Y. The phone reset successfully.
Thank you very much!!!
samsung i600 phone download failed
Hi jackylui,
did you found a solution for "Phone download failed" problem? i tried to uprade mine, but have now same problem as you had.
if anyone else knows the solution, please help.
Thanks,
Tomek

Bricked P3300 - Please help.

Hi there
The first time that I have attempted to perform the upgrade to a cooked rom and everything has gone horribly wrong.
A reset (using the pin hole) gives a blank display. Nothing at all.
A hard reset (using pin hole and soft keys) gives the option to perform hard reset by pressing Yes. This then gives HTC logo screen and then system hangs after displaying
IPL 3.13.0001
SPL 1.11.0000
I can go into bootloader screen (pressing two side buttons) and can connect USB. When I try to install factory ROM or any cooked ROM it stops at 2% and gives me an error saying
Error 228 - Invalid File Size
Is there anything I can do to save my device?
Please help.
are you sure that you have the right factory rom?
must be the one that was on your device when you bought it!
had the same problem! flashing with original rom solved it!
Yes - this is the WM5 rom that I had orginally before upgrading to WM6.
Bricked P3300
try and remove the minisd card
that must be the cause
cheers
jayzd1
Bootloader is not just by pressing two buttons. Press both the buttons and make a soft-reset. When the tri-color screen appears, connect to USB and perform the ROM upgrade again. If it fails, perform the upgrade with a factory ROM. This will bring back your device to working condition.
Next time before flashing, make sure you have applied Hard SPL once.
Regards,
Carty..

Categories

Resources