It's dead... terminal get device data error - JASJAR, XDA Exec, MDA Pro Software Upgrading

Hi
just tried to upgrade my ROM on the O2 exec. It's a brand new machine. Followed the instructions, but I received a 'get device data error' message and now my 02 exec is dead. I've tried soft and hard resets, holding down the power + reset, power+backlight+reset, removing the SIM & battery etc etc. No life. If I do a hard reset, I see a screen asking to press 0 for factory defaults or x to exit - I've tried both to no avail. Any suggestions?
Thanks

signs of life...
Just followed some tips on this forum regarding the MAUpgradeUt_noID utility and it is currently upgrading it's radio stack... so it looks like I will have signs of life here... perhaps now I should change my username cause I'm not confused anymore... thanks to all those who posted previously...

Success through a different route - O2 users please read
OK, I may be a dumba55, but I could not get the previous method to work. I downloaded the current O2 ROM, unzipped it using WinRAR, then ran the program ROMUpgradeUt rather than the previously suggested MaUpgradeUt_noID, which I tried twice but the device would not leave the bootloader screen. I then performed a hard reset (holding the two - keys below the screen and depressing the reset button) and wallah... it's back alive again. The funny thing is O2 actually sent me a replacement unit because of this problem previously... :lol: thankyou O2 from a dumba55.

Related

I've tried upgrading my JasJar with Xda_Exec_Upgrade_v1.30

I guys, I've tried upgrading my JasJar with Xda_Exec_Upgrade_v1.30.162, using MaUpgradeUt_noID and when update was complete I cannot load my JasJar anymore. I am using hard reset, but when choosing "0" off the boot screen - noting happens and screeen remains black.
Can someone please help me with this issue?
Thanks a lot in advance,
Best regards,
Stazik
Try reflashing it again. If it does not work, try reflashing back to the i-Mate ROM.
Whats the version of your bootloader (the screen with serial at the top changing to usb when plugged into usb)? If it is 0.56 or something else below 0.6 thats an already known problem.
I had similar problems with my O2 upgrade.
Try:
- Turn off USB in ActiveSync
- Hold Power/Light and press reset button
- Run the upgrade again
Thank you very much for help and support, guys!
When I try flashing my JasJar with Bootloader update or JASJAR_WWE_13076_164_10900_wwe_ship I get the same error message: Error 101 Connection Error. And also when I disable ActiveSync USB and plug my Jasjar into USB - I get a message from windows saying the device was not recognized...
The only I can get from JasJar is a black screen, except when I press two soft buttons and reset - that gives me a screen with 0 and x to choose. Neither of choices helps thou.
Any help is appreciated. Thanks a lot.
you didnt answer the question re the boot loader number.
when your screen is grey or starting to reset, there are numbers on the screen. what are they.
if it is less that 0.6 your in trouble and assistance is different to if your boot loader is 1.0 or similar.
My screen doesn't change from gray except when I do hard reset. And then I hit two buttons and reset, then press 0 the message Clearing now appears and then everything returns to gray again.
How can I tell the version of bootloader in this case?
Thank you in advance!
they are hard to see, if the screen is grey, the numbers are black.
f the screen is blue/coloured, the nmbers are probably red.
Thanks for help guys,
I brought my JasJar for service today, somehow they were able to put older ROM in there. Now I've upgraded bootloader, hopefully newest ROM from i-mate going to fit without problems )
Well I've killed my Jasjar upgrading I was installing the bootloader update. It sat there saying "Checking information on your device" for about 30 minutes after the update started (notes said it would take 10 so I figured something was amiss - disconnected & rebooted my PC.
Now when I turn the Jasjar on I get the USB/Serial screen referred to above and (good news I figure) it has v1.00 at the bottom. How do I fix this?
TIA
Sheesh. I did a search (I know I should have done that first) and found the answer here
Took a while to find a copy of mtty to download, but found that at http://buzzdev.net
Once I'd done the Set 14 0 and tried the boot loader update again it took seconds so something definitely went wrong the first time.

Stuck in Bootloader without USB support!

OK, I get my MDA, and it comes with German on it (I dont know any german).
I wanted to put an updated rom on it anyway. After an hour or 2 of reading all types of posts and directions on updating, I dl the indria 3.2b5 and try to install it. After the machine resets shortly after resetting, it said comm error. I tried again, and it would say currently installed: ver 0.00. Installing: ver 0.00.
I tried clicked ok once, but the status bar never moved after a LONG TIME.
I had to pull the plug to get it to stop. After trying a few different installations, including radio only, adding radio to other things, I kept getting ver 0.0 like mentioned above. Finally I tried a hard reset (pwr button + reset) and now it when it resets, if I plug the USB plug in, it still says serial on the screen, and the computer doesnt recognize the device plugged in. I tried pulling the battery out for 10 seconds (sometimes that works with things??) but it didnt help. The bootloader is v1.00. IT is a Tmobile MDA (pro) and I dont know if the ORIGINAL language was german, but Y and Z are in opposite locations and theres one or 2 other characters not normally on an english keyboard.
PLEASE HELP ME!!!!!! (hopefully it is not dead forever???)
I will pull the battery to preserve life after messing with this thing!
-- AshayinFLA
edit -- update
ok after writing this, I tried reset with pwr + light and ...
USB WORKS!!!
now it is in the middle of an update with a fresh radio and the indria software... I will update this thread again if it works.
-- AshayinFLA
OKAY, after doing a radio only (v1.09) install, it FINALLY boots up to a rom!! ITs not the one I originally put in,because I put a jasjar in after it (mistakenly thinkingit was a radio only rom). Anyway, I feel comfortable enough re-loading roms onto this now (that I am becoming an expert very quickly) so I will try getting the one I want on it, but IT WORKS!!! Thank you to all who might have had suggestions, although I figured it out within a few hours of the original post
-- AshayinFLA

4 color bands at boot

Hi,
I have a problem with my QTek 9090.
when i want to hard reset it, (power, record, camera and reset) it just displayed the 4 colored bands and stuck here.
how can i restore the normal booting sequence ?
thx.
this is normal, no problem. OS is kichen, no orginal. My Qtek work perfect WM6. Thanks Helmi!
so what should i do because it is block on this stupid 4 colored bands screen...
hard and soft reset do not help.
are you sure you have chosen No/Yes/Yes to clean the registy hive and format the storage at hard reset?
have you pressed the Mail Button to execute the instruction?
being stuck at the 4color screen is a common glitch in wm6 upgrading but nothing serious, that's because even though you flashed the ROM, your storage still has the files of your OLD Os (ex. WM2003).
you have to format the storage to have a fresh and working OS.
the problem is that i did not get any message on screen to which i can answer yes or no :-(
i effectively read some article in this forum about such step, but my Qtek 9090 did not propose me something like that !
:-(
i tried the steps you posted in http://forum.xda-developers.com/showpost.php?p=1603200&postcount=8
but the menu is never displayed :-(
oh... ok.
try pressing Camera + Record... before you stick the Soft Reset.
hold them until you see the menu.
if that doesnt work. then maybe one of the required button is failing.
good luck!
unfortunatelly, it does not work :-(
this is making me crazy...
try searching for MMTY hard reset. that's probably the thing that you need.
i did not find anything about MMTY and hard reset...
:-(
any additional help would be very appreciated
You would find you get a better response if you explain what rom it was that you were installing when this happened,was the rom for your device and did it complete fully?
scousemartin is right... we need details.
about MTTY ok...
here's a link about MTTY on Hermes Bootloader... some of its commands are general and can be used on BA with care.
look for something specific to your problem
i.e. Task 28 to format your DOC.

Did something wrong

Well, it seems, i'm having a big problem:
i wanted to upgrade my fresh MDA Pro to WM6.1 as i wanted to have SDHC-Support and didn't find any really working one with WM5. But: I DIDN'T FULLY Charge the battery, so i received an error as the device couldn't flash the ext-rom. I can still enter the factory-reset-screen. Is the battery going to charge there, too?, so that i can just wait and wait, ultill the battery is going to get full and reflash?
Well, in short:
Wanted to upgrade my device, it failed (maybe due to low battery)
I can still enter the hard-rest / "reset to facory defaults"-screen
if i press any button therem (ie 0 or X) the battery-led links red short and nothing happens.
tried entering bootloader, but nothing happened exept for the battery-ed short red blinking.
does the battery keep charging in the "reset to defaults"-screen?
is it possible to flash this device via SD-Card?
WELL - FIXED IT MYSELF, i was able to enter the ootloader and exectue the task 28at mtty, so i went back to original rom!!
thanks for the info with the tasks and mtty-tutorial
tw, i tried around with the SDHC-Drivers / Files, but didn't find any really working. Which driver works on 8G SDHC Class6-Card?

[Q] Bricked Artemis - can enter bootloader

Hello,
a friend of mine probably bricked his Artemis. He tried to flash, but did not HSPL first. Now the device can enter only bootloader. I tried many USPLs, MTTY, micro SD but nothing worked.
The version of SPL is 1.14, active sync does not go green after connecting, but if I try to flash, it is recognized and returns Error 300. I guess I need the original ROM, but it was in czech and I cannot find it anywhere.
Any ideas are very welcome.
Thanks in advance.
parizek said:
Hello,
a friend of mine probably bricked his Artemis. He tried to flash, but did not HSPL first. Now the device can enter only bootloader. I tried many USPLs, MTTY, micro SD but nothing worked.
The version of SPL is 1.14, active sync does not go green after connecting, but if I try to flash, it is recognized and returns Error 260. I guess I need the original ROM, but it was in czech and I cannot find it anywhere.
Any ideas are very welcome.
Thanks in advance.
Click to expand...
Click to collapse
for SPL Artemis you can try this and to l his official ROM you can look at -> http://www.shipped-roms.com/index.php?category=windows mobile&model = Artemis​ but first try to him that your friend's device hardreset !! like this way :To perform a hard reset
Press and hold the Left SOFT KEY and the Right SOFT KEY, and at the same time, use the stylus to press the RESET button at the lower left side of your device.
Release the stylus, but continue pressing the two soft key buttons. Release them only when you see the following message on your device screen: “Press Send to restore manufacturer default, or press other keys to cancel.“
Press on your device. Warning! Your device will be set back to factory default settings. Please ensure any additional installed programs and/or user data have been backed up before a hard reset is performed.
thanks for ideas. HR cannot be made - returns error like "cannot format partition".
On the shipped ROMs site I cannot download anything - it only says something about redirection on ppc geeks
Here I attach the screen, what I get after trying to flash..
...
only the original rom will bring your device back to life.
whats your red numbers and letters at device start-up?
I can get only to bootloader, so the IPL : 1.14.0001 and SPL 1.14.0000 , that's all I can get
hmm, after a communication with official HTC servise in Czech Republic I got the number of original ROM and successfully downloaded it.
But still the same issue. Is it possible, that Bootloader is corrupted ? The guy told me that it is the only possible cause, if this ROM does not work
...
Try this original rom..
The bootloader of this rom matches yours..
(1.14.0000)
1. Put device into bootloader
2. Connect device to PC
3. Run the RUU
4(a). If this does not work, then you are stuck in the mud..
4(b). If that original rom does work, then click here for USPL 1.11.CMON
Good luck!
Rn
Hi,
thanks man for all the ideas. Unfortunately the ROM you are hyperlinkinkg I have already tried with no success. I have given it maximum, now I am giving it up.
Thanks for your patient help.
p
ME to in same problem plz help IPL 3.04.0001 and SPL 3.04.0000

Categories

Resources