Develop Bugs

How to get into Bootloader

Hi there!
What key combination gets me into the bootloader?
I've been wondering and searching for a way to upgrade my MDA pro rom. (searching for hours on xda, google and a lot of other specialized sites. Turned out to be dead ends! FRUSTRATING!
I'va had a Qtek S100 before. There was a way to get into the bootloader. And there is a way into the bootloader for the Universal to! YES!
But when i try to push the buttons
on/of
Camera
reset button
i cant get in!
button 1 and 2
reset
the same problem.
I get as far as the pres 0 or X for factory default and exit.
Who can help me? I have the no_id upgrade utility and the ROM ready.
Was there a UUL file which i had to edit before using this upgrade method?
I hope there wil be a good tutorial for this just like the one i have used to upgrade my S100 to an orange rom. (worked great!)
Can anyone help me please

Its BACKLIGHT BUTTON + POWER BUTTON + RESET HOLE
It's better to do this without the SIM and Memory Card connected. Disconnect also the USB Sync Cable.
After entering bootloader, you will see SERIAL written on the screen but the screen has no backlight so you have to look hard.
Then when you plug the Sync Cable, the SERIAL will change to USB then you can run the NoID to update.
Remember the NoID has to be run twice in a row as the first time usually solicits an ID Country error

It Works
Thanks Jorge!
Just those keystrokes helped me a lot. It works just fine and it took me only one run to Initiate the upgrading.
Thanks a lot!
I followed your advice and removed the SD and the phone card.
Yes! now i can experiment with these ROMS.
First Jasjar, later O2 and hoping for the best roms with the best programs.(hoping to find a messenger cab file in the jasjar rom)

As I am planning to do the same, Try all the variants of the ROM's, could you inform me what are the good and bad points of all the different ROM's you used and which did you decide to use finally.
Thanks

HELP !!!!
I turn on my Qtek 9000 and i see SERIAL written and the screen but the screen has no backlight.
How can I boot my Qtek 9000 again without this SERIAL mode ????
Best Regards

Hi Ecraseur,
if You did not do anything else (no upgrading), try ColdReset : Power-switch + Reset hole.
Ruud

If we can boot from Serial/USB is it possible to boot from Mini SD? I'm toying with the idea that by using a Linux Live Disk content on a Mini SD it may be possible to boot into a virtual Linux environment? I know it's going to be uber slow and may not even work but I thought it may be worth a look?
If a Mini SD boot isn't possible do you think it'd work to have one of the smaller USB bootable Linux flavours as the USB boot for the HTC Wizard etc?

pls help!!!!wm6 hard reset

hello i have wm6 on my ba and i wanna give hard reset!!! i don't know how! please help!!!!

Have a look here:
- http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel
- http://wiki.xda-developers.com/index.php?pagename=BlueAngel_For_Beginners
And next time try this one: http://forum.xda-developers.com/search.php
Greets Rossi

pls help~~~
where? i have ba whit wm6!!! i try all of them for there, not working! there is for ba whit wm5 or wm2003! for wm6 nothing!

helppp!!
on/off + reset button at the same time... not work!
recor+ on\off+reset =serial message on the screen ( i think that is bootloader)
anything alse i need! please helppp!!!

I can't hard reset either
I have followed all of the directions on the wiki, I have even tried to install another rom and it still will not remove all of the data, it changed the information in the about section of my settings but that's it. I want to change ROMs but it is not working. any ideas?

What version of windows is on your PC?
also try the enter BL which is on most ROMs

Hard Reset
To hard reset you do a soft reset (power + reset)
and before it shows the version numbers at the bottom you have to press Record + Camera & also power (i think) and then you come to an options screen using the record button to go down the list and camera to select you select Yes for option 2 and 3 and then hit the mail button to apply.

jidi22 said:
hello i have wm6 on my ba and i wanna give hard reset!!! i don't know how! please help!!!!
Click to expand...
Click to collapse
swick off button & rest buton in the same time but take care if is not the original windows you may have problems
Warm Boot: Reset the unit by pressing reset button.
Cold Boot: Press Power ++ Reset the unit simultaneously.

Read this. It's how to hard reset your BA. Hope it helps. Make sure you already formated the storage.
Code:
http://wiki.xda-developers.com/index...izzardUpgrade4

Hard Reset?

Hi all...
My Blue Angel wont hard reset. I just bought it second hand and have been trying to hard reset it. I read up and the instructions are to keep the power button pressed while resetting with the stylus. But no matter how many times I tried, this procedure only soft resets the device. Please help!

Try it the software way by going to start>settings>system>clear storage>1234>ok.

kareem9nba said:
Try it the software way by going to start>settings>system>clear storage>1234>ok.
Click to expand...
Click to collapse
Hi buddy.. thanks so much for the reply... but its not working.. tapping on the clear storage icon in settings does not bring up the password screen or do anything at all

wat are my other options people... pls help

anybody??????

i think you make wrong HardReset.
for Hard Reset a BA just press RECORD+CAMERA/PLAYER+SOFT RESET 2 sec. and walaahhh.... there you go.., You'll see three options on screen. You must change the second and the third to yes. If you are not developing/testing software you can disable the first debug option for better performance.
have a nice reset

Stevo.Mksr said:
i think you make wrong HardReset.
for Hard Reset a BA just press RECORD+CAMERA/PLAYER+SOFT RESET 2 sec. and walaahhh.... there you go.., You'll see three options on screen. You must change the second and the third to yes. If you are not developing/testing software you can disable the first debug option for better performance.
have a nice reset
Click to expand...
Click to collapse
Thank you soooo much Stevo... Ur method worked... I wonder why the wiki itself has the wrong method for hard reset... Maybe the hard reset varies from brand to brand... although it should not be since the hardware essentially is the same... Anyways... Hopefully one of the moderators would read this thread and add your method to the wiki...
Million thanks again...

I get that 3 choice screen, but how to I get it to hard-reset AFTER that? If I hit the soft-reset I get the same thing I have gotten for the whole day before. :-(

on the screen must be shown
enable kitl :choose no
clear registry hive : choose yes
format storage : choose yes
change it using the record and camera button.. after that use the mail button to proceed the hard reset

evoluzionne said:
on the screen must be shown
enable kitl :choose no
clear registry hive : choose yes
format storage : choose yes
change it using the record and camera button.. after that use the mail button to proceed the hard reset
Click to expand...
Click to collapse
tried the above but unable to press enter using mail button to initiate rebootin. pls help

Procedure works as advertised
I also was scratching my head over the Hard Reset info in the Wiki not working. This procedure did the trick. Thanks for the help!
Also, for the poster who had trouble with the Mail button not initiating a reboot, just hold it until you get an all white screen, that's what I did and it worked like a charm!

Hard Reset Big Thank Q
Hi every1, the step does work & i would like to thks those who has shared there thought with all.
juz press the "mail" button for about 3 miniutes & you shud see a totally white blankscreen & then it will bring you to formatted WM6. whatever u install previously will be wipe out.
After i hv tried various method.Honestly, this is the only method work to overcome "EXTREME FROZED WM6".
Thks to XDA developer community for sharing.
Just curious, any1 know wat mig hv cause the "EXTREME FROZED WM6"?
Have a nice day every1.
RGds

Thks mysteroid,
For making me holdin on to d "Mail" button. It really works. Brilliant.
Have a nice day.

Consolidated Solution
To the next member whois searchin for a solution here it is:
Problem:My O2 XDAiis won't hard reset. WM6 deep FROZED.
Solution: Extreme Hard Reset a XDAiis just press RECORD+CAMERA+SOFT RESET 2 sec. and walaahhh.... there you go.., You'll see three options on screen. Then use RECORD+CAMERA/PLAYER button to change the value on the setting.
Setting: on the screen must shown
enable kitl :choose no
clear registry hive : choose yes
format storage : choose yes
Finally: use the mail button(act as enter) to proceed the hard reset. U might need to press & hold it for 3minutes.
Kudos to original contributor :Stevo.Mksr(for method) , evoluzionne(for setting) & mysteroid(for keepin the faith).

WM6 deep FROZED -> check/replace your battery

Pocket Loox N560 stuck on boot screen. Won't start up

Does anybody know if there is a way to boot N560 using SD card? I think I killed my FS with some "rom killer" and all I get now is FS boot screen, no other activities.
Any way to start it from SD card and flash it from there?
Perhaps any other way to bring it back to life?

i have the same problem
is there anybody for help???
SOS please

Eenigmaa said:
Does anybody know if there is a way to boot N560 using SD card? I think I killed my FS with some "rom killer" and all I get now is FS boot screen, no other activities.
Any way to start it from SD card and flash it from there?
Perhaps any other way to bring it back to life?
Click to expand...
Click to collapse
You cannot burn the ROM from an SD card.
If the device has had the anti-theft password set at some stage then you cannot reburn the ROM! This might be the problem?
A hard reset on the N560 followed by running the Loox burn program on a PC with ActiveSync connection to the N560 cradle is the only answer i.e. a normal ROM burn.

fingerstoo said:
You cannot burn the ROM from an SD card.
If the device has had the anti-theft password set at some stage then you cannot reburn the ROM! This might be the problem?
A hard reset on the N560 followed by running the Loox burn program on a PC with ActiveSync connection to the N560 cradle is the only answer i.e. a normal ROM burn.
Click to expand...
Click to collapse
Theft protection is not a problem here. It was wrong ROM and now it is stuck on boot screen, active sync does not see it at all, maybe there is a trick to somehow anable burn, flash, service mode on it? So far nothing helps....

Eenigmaa said:
Theft protection is not a problem here. It was wrong ROM and now it is stuck on boot screen, active sync does not see it at all, maybe there is a trick to somehow anable burn, flash, service mode on it? So far nothing helps....
Click to expand...
Click to collapse
read, and pay attention here:
[email protected]@p://a.mod-site.net/gb/u/newplow-1.html
POST 203.
Edit/Delete Message

vladtapes said:
read, and pay attention here:
[email protected]@p://a.mod-site.net/gb/u/newplow-1.html
POST 203.
Edit/Delete Message
Click to expand...
Click to collapse
GREAT!!!!
Thanks ever so much! You are real HELP!!!!
You should close process "wcescomm.exe" on PC in task manager. Then hold button record, power and puch reset after that you will come in boot loader. Run the program mtty.1.42 and select usb connect. If You will see the any error just start again mtty. Put command l c:\os_213u.nbf (You should put correct flash file in c:\ or use correct path to os_213u.nbf, l - like L but small). When it will done You should start PocketLOOX5xxFlashTool.exe and flash you PDA.
Click to expand...
Click to collapse

Eenigmaa said:
GREAT!!!!
Thanks ever so much! You are real HELP!!!!
Click to expand...
Click to collapse
do you confirm the method is fully functional?
I made a backup of my german original rom, if i have problems i want to restore it...
have you got a backup of your old wm5?
thanks

Yes it is working! Even if error comes at the end, shut the appie and use FS update tool to finish it up! All perfect!
Google for WM5, it is somwhere out there!

Eenigmaa said:
Yes it is working! Even if error comes at the end, shut the appie and use FS update tool to finish it up! All perfect!
Google for WM5, it is somwhere out there!
Click to expand...
Click to collapse
could you please p.m. to me the link of wm5 other language?
If you refer 4pda...it can't be downloaded, i don't know russian, i registered, but always cannot download...
if you have other link...pls send me...

vladtapes said:
could you please p.m. to me the link of wm5 other language?
If you refer 4pda...it can't be downloaded, i don't know russian, i registered, but always cannot download...
if you have other link...pls send me...
Click to expand...
Click to collapse
You can if you use an translator like www.windowslivetranslator.com or translate.google.com
then it is pretty easy.

I've resolved...
Fully functional WM6.0 newplowe in English...
now I'm searching for editing it in Italian/French but I need to edit the rom part of the XIP (just that).
For doing that, I need to open decrypt the file .nbh file (don't really know howto, and newplow doesn't answer about that... ).

Hi everybody, I need your help. I spent 2 hours to read several posts about N560 brick recover, and I still can't figure how to do it.
I flashed the N560 with the WM 6.1 and then I tried to flash the backup Rom Image ... which failed. Now is stucked in the climbing image ... and is not reacting to nothing. I didn't try the mitty sol because I don't have a clear ideea about using it, I am still a newbie ...
Please, I am begging for help if you can , thanks

rcretu said:
Hi everybody, I need your help. I spent 2 hours to read several posts about N560 brick recover, and I still can't figure how to do it.
I flashed the N560 with the WM 6.1 and then I tried to flash the backup Rom Image ... which failed. Now is stucked in the climbing image ... and is not reacting to nothing. I didn't try the mitty sol because I don't have a clear ideea about using it, I am still a newbie ...
Please, I am begging for help if you can , thanks
Click to expand...
Click to collapse
Try this?
Take the N560 off the cradle. Remove the battery for at least 30 seconds. Reinsert battery and back cover. Do not worry if the screen shows the dolphins again. Do a full hard reset to get back to factory setting i.e Simultaneously press and hold the Suspend/Resume button (1) and the Calendar application button (2). Briefly press the stylus tip into the soft reset opening (3). Continue to hold down the Suspend/Resume button and the Calendar application button for a few seconds. The reset can take a few minutes. At the end an acoustic signal sounds. Please follow the further instructions on the display.
A hard reset should put the device back to the existing (last burned ROM) and you can try the burn again.
You probably do not know why the burn originally failed. The most common reason is some interrupt of the processor (internet access, switch of all internet access) but more likely something is polling the USB port, which might be shared in the PC. My external USB TV tuner constantly polls the USB port and interrupts any transfers on other ports! I suggest that you disconnect all other USB devices and make sure that your N560 cradle is connected to a USB port directly on the motherboard of the PC (not a USB hub or expansion card with multiple USB ports).
Hope this helps.

N560 - still stucked in the climbers bagground after WM 6.1 flash
fingerstoo said:
Try this?
Take the N560 off the cradle. Remove the battery for at least 30 seconds. Reinsert battery and back cover. Do not worry if the screen shows the dolphins again. Do a full hard reset to get back to factory setting i.e Simultaneously press and hold the Suspend/Resume button (1) and the Calendar application button (2). Briefly press the stylus tip into the soft reset opening (3). Continue to hold down the Suspend/Resume button and the Calendar application button for a few seconds. The reset can take a few minutes. At the end an acoustic signal sounds. Please follow the further instructions on the display.
A hard reset should put the device back to the existing (last burned ROM) and you can try the burn again again.
You probably do not know why the burn originally failed. The most common reason is some interrupt of the processor (internet access, switch of all internet access) but more likely something is polling the USB port, which might be shared in the PC. My external USB TV tuner constantly polls the USB port and interrupts any transfers on other ports! I suggest that you disconnect all other USB devices and make sure that your N560 cradle is connected to a USB port directly on the motherboard of the PC (not a USB hub or expansion card with multiple USB ports).
Hope this helps.
Click to expand...
Click to collapse
Hi and thanks a lot for your post ... I tried several times this procedure ... I see no change for the hard reset .. No dolphins image at all ... I would say whatever I do it doesn't affect it. No sound, no other signs ... same climbing image.... Please keep remember other solution, It should be one ... thank you again ...

rcretu said:
Hi and thanks a lot for your post ... I tried several times this procedure ... I see no change for the hard reset .. No dolphins image at all ... I would say whatever I do it doesn't affect it. No sound, no other signs ... same climbing image.... Please keep remember other solution, It should be one ... thank you again ...
Click to expand...
Click to collapse
THANKS FOR HELP, I didn't made correctly the the procedure ... now all it's Fine ... really appreciate your help ... saved my precious loox ...

rcretu said:
THANKS FOR HELP, I didn't made correctly the the procedure ... now all it's Fine ... really appreciate your help ... saved my precious loox ...
Click to expand...
Click to collapse
PHEW! Thank goodness. I suspect you did not do the hard reset correctly at first. But I agree about the Loox being precious! I look after mine very carefully! Glad I could help you. My pleasure....

My fs560 is brikked!!!!
It remains to climbing people...
I can enter to bootloader (dolphins) but i cannot update to Windows mobile 6.1 Classic ver. 063.07
I need your HELP!!
I tried to use mtty and i can arrive to:
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,0236002Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
but then I cannot initialize normal update, it remains to dolphins with the blue bar fullfilled by precedent mtty...
the PocketLOOXN560FlashTool.exe can't find the device...
Can someone explain me the CORRECT method after mtty?
PLEASEE!!!

vladtapes said:
My fs560 is brikked!!!!
It remains to climbing people...
I can enter to bootloader (dolphins) but i cannot update to Windows mobile 6.1 Classic ver. 063.07
I need your HELP!!
I tried to use mtty and i can arrive to:
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,0236002Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
but then I cannot initialize normal update, it remains to dolphins with the blue bar fullfilled by precedent mtty...
the PocketLOOXN560FlashTool.exe can't find the device...
Can someone explain me the CORRECT method after mtty?
PLEASEE!!!
Click to expand...
Click to collapse
I think you have received a reply from Newplow on his guestbook....

Hi
I tried to upgrade to 128mb but after restart I see only climbing. I tried everything here but on dolphins afterr line is blue it is finished. that I am unpluging device. starting looxflastool for 560 and first is trying to connect by active sync and that when no connection made I see dolphins on left screen of flash tool window. than I am pluging again and after couple secs I see that: Error"The language in this Flash Image update (ENGLISH) differs from that on your device. I tried to change rom on every language but not working as well. PLEASE HELP!!
if that helps than i will add than on top when delfins i see on 560 is two lines. first is typed 2.14.G4 on second directly below is 2.15.
and when mtty 1.42 finishing flashing i see following:
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,0224002Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
I've done already procedure You've mentioned here with taking of the battery for at least 30 secs with hard reset afterwards but it is still climibing screen. Can U manage this as well???
THX

The most common error with the procedure is NOT making a proper or true hard reset, or back to factory settings reset. If you do it wrong, you will only achieve a soft reset, the same as you get if you just put the stylus in the reset hole in the base of the N560.
The correct procedure is to hold Power/Resume/Suspend button (on/off button) and the Calendar button simultaneously. Keep holding them and with the other hand press in the reset hole with the stylus. The screen should blank out. KEEP holding the other two buttons all this time, and release the stylus. KEEP holding those two buttons until the screen display returns, only then release them.
This should allow another burn.
I hope this is the problem. It has happened to me and others, so I think I am right. But if this fails, you may need another approach.

[Q] Bricked Artemis - can enter bootloader

Hello,
a friend of mine probably bricked his Artemis. He tried to flash, but did not HSPL first. Now the device can enter only bootloader. I tried many USPLs, MTTY, micro SD but nothing worked.
The version of SPL is 1.14, active sync does not go green after connecting, but if I try to flash, it is recognized and returns Error 300. I guess I need the original ROM, but it was in czech and I cannot find it anywhere.
Any ideas are very welcome.
Thanks in advance.

parizek said:
Hello,
a friend of mine probably bricked his Artemis. He tried to flash, but did not HSPL first. Now the device can enter only bootloader. I tried many USPLs, MTTY, micro SD but nothing worked.
The version of SPL is 1.14, active sync does not go green after connecting, but if I try to flash, it is recognized and returns Error 260. I guess I need the original ROM, but it was in czech and I cannot find it anywhere.
Any ideas are very welcome.
Thanks in advance.
Click to expand...
Click to collapse
for SPL Artemis you can try this and to l his official ROM you can look at -> http://www.shipped-roms.com/index.php?category=windows mobile&model = Artemis​ but first try to him that your friend's device hardreset !! like this way :To perform a hard reset
Press and hold the Left SOFT KEY and the Right SOFT KEY, and at the same time, use the stylus to press the RESET button at the lower left side of your device.
Release the stylus, but continue pressing the two soft key buttons. Release them only when you see the following message on your device screen: “Press Send to restore manufacturer default, or press other keys to cancel.“
Press on your device. Warning! Your device will be set back to factory default settings. Please ensure any additional installed programs and/or user data have been backed up before a hard reset is performed.

thanks for ideas. HR cannot be made - returns error like "cannot format partition".
On the shipped ROMs site I cannot download anything - it only says something about redirection on ppc geeks
Here I attach the screen, what I get after trying to flash..

...
only the original rom will bring your device back to life.
whats your red numbers and letters at device start-up?

I can get only to bootloader, so the IPL : 1.14.0001 and SPL 1.14.0000 , that's all I can get

hmm, after a communication with official HTC servise in Czech Republic I got the number of original ROM and successfully downloaded it.
But still the same issue. Is it possible, that Bootloader is corrupted ? The guy told me that it is the only possible cause, if this ROM does not work

...
Try this original rom..
The bootloader of this rom matches yours..
(1.14.0000)
1. Put device into bootloader
2. Connect device to PC
3. Run the RUU
4(a). If this does not work, then you are stuck in the mud..
4(b). If that original rom does work, then click here for USPL 1.11.CMON
Good luck!
Rn

Hi,
thanks man for all the ideas. Unfortunately the ROM you are hyperlinkinkg I have already tried with no success. I have given it maximum, now I am giving it up.
Thanks for your patient help.
p

ME to in same problem plz help IPL 3.04.0001 and SPL 3.04.0000