Related
Hey guys,
I've searched the forum for like 5 hours or so
to find a thread that could help me solve this solution...
I've tried everything that had something to do with "dead"
in the BlueAngel and Blueangel Update etc. section
What it does:
- The screen stays black
- If I try to charge, the Red 'Charging' LED doesn't become red
unless I take the battery out of the Qtek and charge..
Then it gets red (WEIRD)
- No connection with activesync or rom update utilities
What happened:
- Rom update stopped after a few percentages...
If i try to get a new rom in it with or without cradle
with the following rom update utilities:
- BaUpgradeUt.exe:
then I get a Connection Error (101) when I try to update
- MaUpgradeUt_noID.exe:
ERROR 150: ROM UPGRADE UTILITY ERROR
(Rom Utility not designed for this device)
or "Finished" immediately (but it's not finished)
(Depends on the rom I use, and I used like 10 different roms)
Soft reset / Hard reset doesn't work,
I even tried to Hard Reset by holding the
Voice Record button + Power button + Reset button for 2 minutes
(I tried Camera + Power + Reset too) with the battery,
and I tried these without the battery...
No reaction...
If someone can help me, please do...
Thnx in advance
Maybe you can try thingds from this
http://forum.xda-developers.com/viewtopic.php?p=291989#291989
sep said:
Maybe you can try thingds from this
http://forum.xda-developers.com/viewtopic.php?p=291989#291989
Click to expand...
Click to collapse
Nope,
I've tried that too, but I don't get the USB or WCEUSB in mtty...
The COM ports don't react.
I know how to use it, because I used it like 10 times or somethin'
But I think the problem is, that I can't get in the bootloader mode
(or any other mode)... So there's no response from my Angel..
Thanks anyway..
have you tryed to remove battery, leave it without battery fo an hour or two then put the battery back and power on the device ?
this method may boot your device. If it worked go imediately in bot loader mode and reflash your favorite rom
If it does not helps maybe it is hardware problem ... and you should leave your device in service center
Tried this too
Isn't there any solution except for service center?
I want to know how I can solve this problem,
'cause it could happen again when I update the rom later.
And I know I'm not the only one with this problem.
It would help me and a lot of other BlueAngel owners..
Is it possible to make a serial connection with the bottom I/O port and issue the necessary commands with mtty? could be that there is some logic powered on the board but not enough to make the "USB" section powered up.. similar to serial a console cable on network gear etc. OR.. is there any known secrets such as a hardware debug mode initiated with certain pin(s) on the I/O connector.. such as grounding one or two.. any HTC tech documents floating around for troubleshooting?
You are not one with this problem. The same happens with me too.
Let searching for solution together.
If you want you can contact with me by icq: 190812766
OK, I get my MDA, and it comes with German on it (I dont know any german).
I wanted to put an updated rom on it anyway. After an hour or 2 of reading all types of posts and directions on updating, I dl the indria 3.2b5 and try to install it. After the machine resets shortly after resetting, it said comm error. I tried again, and it would say currently installed: ver 0.00. Installing: ver 0.00.
I tried clicked ok once, but the status bar never moved after a LONG TIME.
I had to pull the plug to get it to stop. After trying a few different installations, including radio only, adding radio to other things, I kept getting ver 0.0 like mentioned above. Finally I tried a hard reset (pwr button + reset) and now it when it resets, if I plug the USB plug in, it still says serial on the screen, and the computer doesnt recognize the device plugged in. I tried pulling the battery out for 10 seconds (sometimes that works with things??) but it didnt help. The bootloader is v1.00. IT is a Tmobile MDA (pro) and I dont know if the ORIGINAL language was german, but Y and Z are in opposite locations and theres one or 2 other characters not normally on an english keyboard.
PLEASE HELP ME!!!!!! (hopefully it is not dead forever???)
I will pull the battery to preserve life after messing with this thing!
-- AshayinFLA
edit -- update
ok after writing this, I tried reset with pwr + light and ...
USB WORKS!!!
now it is in the middle of an update with a fresh radio and the indria software... I will update this thread again if it works.
-- AshayinFLA
OKAY, after doing a radio only (v1.09) install, it FINALLY boots up to a rom!! ITs not the one I originally put in,because I put a jasjar in after it (mistakenly thinkingit was a radio only rom). Anyway, I feel comfortable enough re-loading roms onto this now (that I am becoming an expert very quickly) so I will try getting the one I want on it, but IT WORKS!!! Thank you to all who might have had suggestions, although I figured it out within a few hours of the original post
-- AshayinFLA
I did a rom upgrade on an hx2110 - installed successfully, but now the only thing I can get the pda to do is go into Pre bootloader mode (i.e. Pre-BL 1.00.02 blue screen). SO I tried the universal bootloader method - makes it all the way to the flashing portion but then does NOTHING - the terminal simply sits there saying "ready" and does not upload anything - the program sees the correct communication port (ie. usb01 or whatever). HOW do I force an upload???
Thanks!
Rusty
On another note - I had purchased a working 2110 with a good mobo to replace this one if the flash is not repairable - is that a difficult procedure? Unfortunately, the 2110 I purchased was not working, but this may still be in the books at a later time, so some info would help.
Thanks!
Rustmonkey said:
I did a rom upgrade on an hx2110 - installed successfully, but now the only thing I can get the pda to do is go into Pre bootloader mode (i.e. Pre-BL 1.00.02 blue screen). SO I tried the universal bootloader method - makes it all the way to the flashing portion but then does NOTHING - the terminal simply sits there saying "ready" and does not upload anything - the program sees the correct communication port (ie. usb01 or whatever). HOW do I force an upload???
Thanks!
Rusty
Click to expand...
Click to collapse
Rusty,
You are so lucky that I experienced this problem and solved it on my own. You did not specify what ROM you were loading, but here is the fix:
First you need to get another pocketpc, hx2000 series like yours that is working.
Put that device into white screen bootloader or pre-BL mode (depending on which device you got to borrow)
Ensure that the battery on that device is 100% charged.
Run the original ROM upgrade for the ROM you wish to install (use PDAViet if it's WM6 and use the HP SP32408 to Run it)
Hit all the Ok screens until it brings you to the one that has the "UPDATE" button.
Remove the working Ipaq from the cradle and place it's 100% battery in you own.
Put your Ipaq into pre-BL mode and put it on the cradle. Press the calendar button to activate the usb drivers.
Once it says "USB", Hit the "UPDATE" button and it will load the proper ROM to your IPaq.
When It is done, perform a hard reset by formatting the PS on the device.
Voila!! Your Ipaq is Un-Bricked!! Put in your original battery and charge it up!
Enjoy!!
Bless...
hi Rustmonkey,
i have the similar things - i made my hx2110 brick when i flashed it with a different language ROM, it went 100% when i flashed the ROM but didn't work at all after that.
the problem is i can get it in the bootloader mode after trying many ways, at the same time the pc can't find any USB device at all.
how to make it work again?
thanks.
reggaepoo said:
Rusty,
You are so lucky that I experienced this problem and solved it on my own. You did not specify what ROM you were loading, but here is the fix:
First you need to get another pocketpc, hx2000 series like yours that is working.
Put that device into white screen bootloader or pre-BL mode (depending on which device you got to borrow)
Ensure that the battery on that device is 100% charged.
Run the original ROM upgrade for the ROM you wish to install (use PDAViet if it's WM6 and use the HP SP32408 to Run it)
Hit all the Ok screens until it brings you to the one that has the "UPDATE" button.
Remove the working Ipaq from the cradle and place it's 100% battery in you own.
Put your Ipaq into pre-BL mode and put it on the cradle. Press the calendar button to activate the usb drivers.
Once it says "USB", Hit the "UPDATE" button and it will load the proper ROM to your IPaq.
When It is done, perform a hard reset by formatting the PS on the device.
Voila!! Your Ipaq is Un-Bricked!! Put in your original battery and charge it up!
Enjoy!!
Bless...
Click to expand...
Click to collapse
You, my good sir, are a genius - worked great! Fixed BOTH 2110s
tangwd898 said:
hi Rustmonkey,
i have the similar things - i made my hx2110 brick when i flashed it with a different language ROM, it went 100% when i flashed the ROM but didn't work at all after that.
the problem is i can get it in the bootloader mode after trying many ways, at the same time the pc can't find any USB device at all.
how to make it work again?
thanks.
Click to expand...
Click to collapse
You're going to need another hx2000 series to make sure the battery is fully charged - put the battery in and then use the bootloader keystrokes immediately (contacts+itask+reset) - you made need to tap reset a few times while holding the other two to get it to work. After it is in bootloader mode, push the calander button while it is connected to the cradle/usb to get the pc to recognize it
Rustmonkey said:
You're going to need another hx2000 series to make sure the battery is fully charged - put the battery in and then use the bootloader keystrokes immediately (contacts+itask+reset) - you made need to tap reset a few times while holding the other two to get it to work. After it is in bootloader mode, push the calander button while it is connected to the cradle/usb to get the pc to recognize it
Click to expand...
Click to collapse
really amazing !!!!!!
I just saved my hx2110 as per your step by step instruction now.
Thank you very much.
ok, well, I thought they were fixed... now one of them freezes at the bootup screen, even when I do a clean reset... I've tried reflashing multiple times to no avail... any ideas whats going on?
ok, got everything working - reflashed the non-working one back to an original 2003 rom - which made if freeze at boot - then upgraded it via pre-bl to 1.00.00.L - from here, it wouldn't do anything after filling the bar at the boot screen, but it didn't CRASH (as in lights out) - so I ran the pre-bl again and ran the flash program for 1.00.00.L again WITHOUT swapping between the 2495 and the 2110 - just put the 2110 in pre-bl and away we went - flashed, formatted, and booted - then proceed to upgrade to WM6 via 1.00.00.H --> 1.02.00.H --> WM6 - works GREAT!!!
Thanks for the help everyone!
Dear All,
I`ve got the same problem but i don`t have a second ipaq.. is there anyway to repair it with out the second device???
Thank you very much
Abs
Hello,
I have run into some problems with a bricked hx2110.
I was flashing the IPAQ to a new ROM WM5 (Battery was full and I read all the instructions 10 times prior to flashing). While flashing, the progress bar went to 100% then faded out immediately and it wouldn't reset (clean reset). I put the battery in my friends hx3000 series and the battery I used was completely dead. It did flash to 100% though, but not matter how many times I try 1 + 3 + reset, it doesn't reboot. If I can figure out how to get it to boot, that would be great, but I can't get anything to come up with any key combinations.
To this point all I can do is get into Pre-BL mode 1.00.04. I have tried the below scenarios on two machines, both running windows XP SP2 (USB 2.0) with the firewall and virus software disabled.
http://forum.xda-developers.com/showthread.php?t=330382&page=4
1) I have tried the above links directions and used the the Universal Bootloader (Bootloader.exe). It gets to the point where it says "The PDA should be updating now" or something similar but nothing happens. I don't get any errors regarding communications (it sees the device when I hold the "Calendar" button until it says USB; windows then recognizes the device as "HP USB ..." so I know it's communicating).
2) I tried to use the Bootloader_GUI.exe beta so that I can watch the progress indicator but it just sits at 0%. There are no error messages so it is communicating but for some reason, the device won't let it flash (and the flash utility thinks it's doing something).
3) I tried the original ROM flash from HP (SP29856.EXE) and it recognizes the device, but because the current ROM on the PDA is hosed, when it does it's "verifying" process, it comes up with "?" marks as the model number and when it goes to flash it starts at .1% then says "FINISHED" immediately. The ROM utility thinks it flashed it correctly but it didn't flash anything. I'm guessing that the verification of the PDA failed and forced the utility to not flash.
Does anyone have ANY ideas of what to try? I wish I had another HX2000 series PDA and try the "swap" thing prior to hitting the update button but I don't. All I have to work off of it my sad bricked PDA and a full battery (friend keeps charging it). His PDA is an HX3000 series.
Any ideas would be appreciated,
Thanks!
Are you using a the HP flash program that is specified for your device?
2nd - you might be able to use your buddies device in a swap as well - not sure but its worth a shot - use HPs upgrade program, let it verify, then swap your device onto the same cable - overwrite the firmware in the update program for HIS device with firmware compatible with yours and then hit update - let us know if this works...
I am using the "official" HP flash program specific for the HX2110 (from their website - SP29856), bootloader.exe, and bootloader_gui.exe
I wanted to try my friends, but he won't let me touch his because I bricked mine lol (I swore nothing would happen to his but he still won't let me try it).
Anyway, I just copied over the ROM image (from HP) and stripped out the header (now showing 64 bytes before the ECEC). The ROM is for WM2003. I copied the ROM in binary using psdwrite.exe to an 256 MB SD card. As soon as I can get the battery back, I'm going to try to flash it from the SD card. If this fails, I am going to try to play around with MTTY / USB and manually call the ROM flash and see what happens.
Having another HX2000 series would make this easy (maybe a little TO easy )!
Bootloader never worked for me - but if you can get it to manually call the flash, more power to you good luck!
Well it was worth a shot. After spending the better part of the day with the PDA, I have made no more progress (can't get Pre-Bl to update). The only option I have now is to find someone with another hx2000 series that is willing to resurrect it from the dead for me (PM me if you can help - I will pay two way fare). Until that happens, it's going in the "broken" drawer with all my old comp stuff .
Thanks to all the tips and tricks that is posted on these forums and brighthand! There is a wealth of information on this topic and without them, I would have gotten nowhere in trying to repair the device (granted, I wouldn't have been intrigued to upgrade the ROM in the first place and would still have a working PDA, but that's besides the point ).
Best of luck to you all.
1).download original ROM from HP (sp29799) -extract files
2) download http://upload.dvhk.pl/content.php?id=88892 - replace files
3) flesh device.
bay!
link crash http://upload.dvhk.pl/content.php?id=88892 - replace files
Please it can raise it again, thanks
Absolut3k said:
Dear All,
I`ve got the same problem but i don`t have a second ipaq.. is there anyway to repair it with out the second device???
Thank you very much
Abs
Click to expand...
Click to collapse
Same here.. is there another way to un-brick hx2110 on this problem ? thx ...
Solved, my hx2100 returns to be in this world
thank you i saved my ipaq
Hi, I have a problem.
My iPaq 114 hangs on the Windows Mobile 6 green boot screen.
I've tried to hard reset, it said "CLEAN BOOT", but that doesn't work. I've tried about 10 hard resets, all the same.
I've then tried using the SP38871 package to update the ROM, but the program tells me there is no connection between the iPaq and my PC.
Then I've found that if I push the Calendar+OK and tap the reset, it goes into a "SDCard Download Image" so I've copied the "HPImage.nbf" file from the SP38871 package, placed it on an SD Card, but then it says: "No download file found"
It's also acting weird, meaning that it does not start when I push the power button, only when I tap the reset (does that mean Windows Mobile boots, but then the whole screen turns black?)
I've uploaded a video to show you what I mean.
http://www.youtube.com/watch?v=I-jeOyB97Qs
What could be the problem ? Could someone please help !
EDIT: I wrote the ROM file (HPImage.nbf) using ntrw.exe, but the iPaq says: "No boot block!" ... Does anyone have a good ROM ? Or if someone has a working iPAQ 114, could you please make a ROM backup and send it to me ? Or paste the HEX ROM Header. Just follow this guide:
http://www.rawen69.cc/hw65xx_flash.html
Ok..... it seems I`m having charging problems...
I thought the battery was full, because the orange light did not come up.... Then, after playing with it a bit more, I notice that it charges only if I take out the battery, put it back in, and the connect it to USB or charger... When I start the device, it does not charge anymore.
Also, I've found that my PC can't even connect with it, eventhough it's running. Could it be the mini-usb connector ? Or maybe the internal ipaq battery ?
I've tried 2 USB-to-miniusb cables, and same symptoms on both of them...
Hi Kiraly,
Hmm, sometimes Devices from HTC is not charging if you into boot loader Modus. that´s the reason why you must always a charged battery before you flashing a new OS.
Do you try: Windows+OK+Audiorecording (button on right side) hold it, make a Reset with you pen and hold the 3 buttons?
start your device normally again?
When your battery is dead:
we have sometimes same Problem, if the IPAQ 114 not used for more then one Month, the battery is deep discharged. Sometimes there is no chance to reactivate the battery. (Same problems we have some years ago with the HTC Wizard too)
I solved that problem with a External (laboratory) Power Supply ( I pushed the + and - contacts of the battery (not mounted into your PDA) really shortly with 12 Volt and maybe fixed current of 1 Ampere.
But this is really dangerous, do that only (if the battery not working or will not charging) for a few seconds. (max 2 x 5 seconds with a short interval between the 5 seconds)
remember that LiIo Batteries can really dangerous.
After this procedure the Battery will charging again. Sometimes it can help too, to leave your PDA connected to PC or Power Adapter for one night.
stuck in RUU download mode
hi,
i've try to update my ipaq 114, but unfortunately i stuck in RUU download mode, i can't do any progress, hardreset is not working..
please help, thx
joy.d said:
Hi Kiraly,
Hmm, sometimes Devices from HTC is not charging if you into boot loader Modus. that´s the reason why you must always a charged battery before you flashing a new OS.
Do you try: Windows+OK+Audiorecording (button on right side) hold it, make a Reset with you pen and hold the 3 buttons?
start your device normally again?
When your battery is dead:
we have sometimes same Problem, if the IPAQ 114 not used for more then one Month, the battery is deep discharged. Sometimes there is no chance to reactivate the battery. (Same problems we have some years ago with the HTC Wizard too)
I solved that problem with a External (laboratory) Power Supply ( I pushed the + and - contacts of the battery (not mounted into your PDA) really shortly with 12 Volt and maybe fixed current of 1 Ampere.
But this is really dangerous, do that only (if the battery not working or will not charging) for a few seconds. (max 2 x 5 seconds with a short interval between the 5 seconds)
remember that LiIo Batteries can really dangerous.
After this procedure the Battery will charging again. Sometimes it can help too, to leave your PDA connected to PC or Power Adapter for one night.
Click to expand...
Click to collapse
Unlike other ipaqs, the 111 and 211 (and their varients) were not made by HTC. They were made by Foxconn. As for your problem, what filesystem is your SD Card formatted. Try formatting it with the FAT-16 file system (if you format the card with the standard windows utility, choose FAT) first, and then putting the image on the card. You might also need a file called BLDIAG.nb0 (search around for that one). Did you ever think to check out the ipaq 211 (or 210) threads to see what they did?
hp 114 stuck in Flash or ruu mode
this happened to me also. To resolve this... download the HP rom up date for hp 114 in hp.com. You should never install this using vista... find a computer with XP OS download corresponding MCDC from microsoft so that XP would be able to recognize your PDA. Then run the spxxxxx (rom update) from your computer...
The upgrade process will take about 7 min. but sadly this does not solve frequent hanging and loss of data by WM6 that is why I am looking around to software updates. Still no luck...
Hi all,
Just received my Vodafone-branded Diamond, and I'm afraid I already managed to brick it!
It was equipped with version "1.37.172.3 NLD" so I decided to upgrade it to the latest version.
The installation of OliNex Hard-SPL 1.93 went flawless, but the installation of ROM "RUU_Diamond_HTC_WWE-ME_1.93.456.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe" stopped at about 25% with error code 302. The recovery method that came with the package didn't help, every time the upgrade stopped at the same moment.
Since the device is stuck in the bootloader, and I'm left with a non-chargeable battery, I tried the official Vodafone-branded "RUU_Diamond_Vodafone_NL_1.97.172.4_Radio_Signed_Diamond_52.44.25.24_1.08.25.08_Ship.exe" ROM. Unfortunately, this upgrade stops at 48% and throws the same 302 error.
Anyone who can tell me what I'm doing wrong, and what I can do to solve all this?
I hope I don't have a brand new, but bricked device on Christmas!
TIA and have a nice day.
Try a hard reset first. If this doesn't help google or search at XDA for MTTY.
This tool can fix your device
http://wiki.xda-developers.com/index.php?pagename=Kaiser_Stuck_at_bootloader
Try this, maybe will work
Try a Vodafone branded stock rom before mtty.
Regards,
Carty..
He already tried a stock rom....
Potential Solution
Have you looked at the thread titled,
[UPG][TRBL]How-to fix: Update/Flash doesnt work, stops at 0% or 5% (invalid model ID)
It may just be a model ID glitch that can me fixed.
Take a look. It's in this forum in a sticky by cptsunshine.
Thanks all for the help, I'll have a look at your suggestions.
The problem isn't that it stops at 0% or 5%, it stops at random percentages (depending on the ROM I use).
I also see the bootloader (red / green / blue), so it's not dead. I guess it's just that it doesn't pick up a ROM.
Besides, the bootloaders says upgrade ROM code error please try again.
Edit:
A hard reset doesn't seem to work. In the bootloader, when I press "volume down" and "enter" together, and press the "reset button" the screen goes black, but then goes back to the bootloader screen after a sec or 2.
Edit 2:
MTTY doesn't do much either, after executing "boot" the phone is showing me the Vodafone logo and that's it.
For the rest, MTTY shows me the following:
Cmd>boot
InitDisplay: Display_Chip=1
dwDirectNum: 0, dwMatrixNum: 0, dwMicroPNum: 0
Fixed new dwPSImageSize = 0x53E0000
Install Rom via Internal Memory Method
Steps from Suiller:
1. open from your PC the rar or zip archive and extract only the BIG .nbh file
2. rename as DIAMIMG.NBH
3. copy the renamed file into the root dir of your "Storage Card" or "Internal Storage" (the one of 4Gb... NOT to the internal phone memory!)
4. reset your device and within 3 seconds push together the Vol_Down + Back button (the one on the right above the hangup button) and keep pressed until the boot loader appears (the one with the color stripes)
5. soon as you see the bootloader stop to press those poor buttons
6. a very simple gray menu will appear asking you what to do, simple press the power button to perform the ROM/Radio upgrade
7. while the upgrade runs be patient and don't press again the power button, reset the device or play with it until it finishes, when finished a message "UPDATE SUCCESS" will appear, now you can safely reset your device
8. who prefer can perform a hard reset after the fresh cook (soon after reset simply press Vol_Down + Circle button, then when you see another simple gray menu choose Vol_Up to confirm format), even if this has no-sense because internal memory is pre-formatted during flash, but... there is always a but... for some unknown "scientific" reason sometimes an hard-reset can save time & headache
Let me know how it goes.
Make sure you have Net framework 3.5 installed on devices.
Nakkie27 said:
Thanks all for the help, I'll have a look at your suggestions.
The problem isn't that it stops at 0% or 5%, it stops at random percentages (depending on the ROM I use).
I also see the bootloader (red / green / blue), so it's not dead. I guess it's just that it doesn't pick up a ROM.
Edit:
A hard reset doesn't seem to work. In the bootloader, when I press "volume down" and "enter" together, and press the "reset button" the screen goes black, but then goes back to the bootloader screen after a sec or 2.
Edit 2:
MTTY doesn't do much either, after executing "boot" the phone is showing me the Vodafone logo and that's it.
For the rest, MTTY shows me the following:
Cmd>boot
InitDisplay: Display_Chip=1
dwDirectNum: 0, dwMatrixNum: 0, dwMicroPNum: 0
Fixed new dwPSImageSize = 0x53E0000
Click to expand...
Click to collapse
u can do one thing then press woluem down and reset bottom at the same time then u go to rescue mode then u wait and put in the usb stick and there stand seriel when u put in the cable it will change to usb thenu can load the firmware again
band27 said:
Steps from Suiller:
3. copy the renamed file into the root dir of your "Storage Card" or "Internal Storage" (the one of 4Gb... NOT to the internal phone memory!
Click to expand...
Click to collapse
I wish I could mate, but I cannot put files on it anymore, since ActiveSync doesn't recognize my device when it's in the bootloader.
janielsen said:
u can do one thing then press woluem down and reset bottom at the same time then u go to rescue mode then u wait and put in the usb stick and there stand seriel when u put in the cable it will change to usb thenu can load the firmware again
Click to expand...
Click to collapse
Can you please be more specific? Are you telling me how to do a hard reset? I tried as to do a hard reset, but it goes back to the bootloader instead of resetting. USB stick?
Thanks all, much appreciated. A pain this can happen, looking at the fact that I did everything exactly as described in all these flashing manuals.
Nakkie27 said:
I wish I could mate, but I cannot put files on it anymore, since ActiveSync doesn't recognize my device when it's in the bootloader.
Can you please be more specific? Are you telling me how to do a hard reset? I tried as to do a hard reset, but it goes back to the bootloader instead of resetting. USB stick?
Thanks all, much appreciated. A pain this can happen, looking at the fact that I did everything exactly as described in all these flashing manuals.
Click to expand...
Click to collapse
first push the volum down buttom at the same time press the reset buttom then the 3 color display will appear and in the buttom will stand seriel then u putt in the usb cable to ur phone whit u have attact to ur pc then it will say usb now u can load new firmware
janielsen said:
first push the volum down buttom at the same time press the reset buttom then the 3 color display will appear and in the buttom will stand seriel then u putt in the usb cable to ur phone whit u have attact to ur pc then it will say usb now u can load new firmware
Click to expand...
Click to collapse
No mate, I never had problems getting into the 3 color screen. The problem was updating afterwards, which never completed without error code 302.
Anyway, I guess I just fully bricked my device after putting SPL-1.40.OliNex (according to the guide at http://forum.xda-developers.com/showthread.php?t=416211) on it. The SPL install was succesful, but when booting I'm now not even getting to see the 3 color bootloader. All I see is the Vodafone logo with some version numbers at the bottom, but that's it. It doesn't boot further on, and I can't get a USB-connection.
Edit:
Volume down + reset brought me in the bootloader again, although it's saying SPL-1.93.OliNex.
Nakkie27 said:
No mate, I never had problems getting into the 3 color screen. The problem was updating afterwards, which never completed without error code 302.
Anyway, I guess I just fully bricked my device after putting SPL-1.40.OliNex (according to the guide at http://forum.xda-developers.com/showthread.php?t=416211) on it. The SPL install was succesful, but when booting I'm now not even getting to see the 3 color bootloader. All I see is the Vodafone logo with some version numbers at the bottom, but that's it. It doesn't boot further on.
Click to expand...
Click to collapse
that i know but as i say in the post that when u do it that way i say u can load new firmware whitout it needs to boot try my friend i have done it 3 times because wrong loading of firmware
u have to only push thoose 2 buttom then it will work because u go to rescue mode
But what will that give me extra? I can access the Hard-SPL 1.93 bootloader (3 color screen), and I can get into USB mode. It's just that the upgrade of both firmwares stop at a certain percentage.
I'm constantly trying to hard reset the device, but after pushing the reset button (with both volumn down + enter pressed down), the device just reboots back into the bootloader and doesn't give me the hard reset warning.
Nakkie27 said:
But what will that give me extra? I can access the Hard-SPL 1.93 bootloader (3 color screen), and I can get into USB mode. It's just that the upgrade of both firmwares stop at a certain percentage.
I'm constantly trying to hard reset the device, but after pushing the reset button (with both volumn down + enter pressed down), the device just reboots back into the bootloader and doesn't give me the hard reset warning.
Click to expand...
Click to collapse
u need to hold them down until it leave the 3 color display an turns into grey
Ok, finally managed to do a hard reset. Afterwards I tried upgrading to the official Vodafone NL 1.97 ROM once more, but it failed at 48% again.
Any ideas what to do? I know have Diamond with Hard-SPL 1.93 (which says upgrade ROM code error) with no working OS.
Ok all, got it finally working again!
Don't ask me why, but flashing the newest Dutty ROM (and the included radio) did work.
Thanks for all your help, and a wonderful evening!
Hi all,
I have a quit similar problem. I've read a lot, but couldn't find an answer to my problem - may bye someone can help me.
I updated my Dimond (OliNex Hard-SPL 1.93, radio 1.09.25.23 and rom dutty V4). When I start my phone most of the time (95% plus) I end up in the color screen - however some time it's starts perfect (without changing anything).
When I get stock in the color screen, I can start the phone with mtty and the command "boot".
What can I do to make my phone always start in the normal way?
Thanks!
Nakkie27 said:
Ok all, got it finally working again!
Don't ask me why, but flashing the newest Dutty ROM (and the included radio) did work.
Thanks for all your help, and a wonderful evening!
Click to expand...
Click to collapse
i smell a radio issue - last time i was trying to upgrade my radio - ended up with something similar, managed it out like you did - but now you're up - so that's good!!
try some other rom (this time without radio) - i don't think you should have any issues going forward... good luck and have fun!