Hey there everybody.
So I was using the stylus normally until the firmware update shows up, after a error on update the pen doesn't show up any more. I already tried to restore/restart the tablet and Bluetooth but without any success.
When I attech doesn't show anything, but when I remove pop a notification in red "charge your stylus now". BTW it already was in 100% b4 the update error.
Update: Apparently it's now showing as "K81 CS(DFU)" on Bluetooth and when I try to pair it says "couldn't pair with K81 CS (DFU) because of an incorrect PIN or pass key"
I have the exact same problem...any solution found yet?
Had this problem when i tried to update 1st time my gf Stylus on her tablet, first i tried with the (original) magnetic cover on and the stylus went onto DFU mode, i pressed on the button closer to the tip for about 10 seconds and the stylus went to normal mode(if i recall right). if this doesn't work try maybe the second button, or both at the same time.
Then i updated the stylus on my tablet without the magnetic cover.
Later received my own stylus and did the update procedure directly whitout the magnetic cover.
If the above doesn't work try to deplete the stylus battery, don`t connect the stylus to the tablet and leave it alone. i don't know the exact time it will last, maybe two days, or maybe a week or more, it has a tiny battery (25 mAh).
If succesfull reboot the table once, be sure to have the stylus linked but not attached to the tablet to be extra safe.
Good luck.
NeoDaemon said:
Had this problem when i tried to update 1st time my gf Stylus on her tablet, first i tried with the (original) magnetic cover on and the stylus went onto DFU mode, i pressed on the button closer to the tip for about 10 seconds and the stylus went to normal mode(if i recall right). if this doesn't work try maybe the second button, or both at the same time.
Then i updated the stylus on my tablet without the magnetic cover.
Later received my own stylus and did the update procedure directly whitout the magnetic cover.
If the above doesn't work try to deplete the stylus battery, don`t connect the stylus to the tablet and leave it alone. i don't know the exact time it will last, maybe two days, or maybe a week or more, it has a tiny battery (25 mAh).
If succesfull reboot the table once, be sure to have the stylus linked but not attached to the tablet to be extra safe.
Good luck.
Click to expand...
Click to collapse
Hi there.
Unfortunately it doesn't work.
I left the battery dry and did all the rest, but when I try to connect to the pen in dfu mode it says "couldn't pair with K81 CS(DFU) because of an incorrect PIN or password".
Okay for some magical reason it worked today.
B4 I tried all the things again I opened the " service & feedback" app and started a "get Bluetooth log" and for some unknown reason it worked.
The LKS said:
Okay for some magical reason it worked today.
B4 I tried all the things again I opened the " service & feedback" app and started a "get Bluetooth log" and for some unknown reason it worked.
Click to expand...
Click to collapse
What is all the things ? Please let me know
hi, can someone explain me what to do? I tried the above but it didn't work
Hi! I'm having exactly the same problem. Firmware update error and then with "K81 CS(DFU)".
Did anyone manage to solve it?
joaojunior said:
Hi! I'm having exactly the same problem. Firmware update error and then with "K81 CS(DFU)".
Did anyone manage to solve it?
Click to expand...
Click to collapse
no, no one could answer me, xiaomi assistance is zero. in the end I made the return of the tablet and pen as I could not any way if it was a pen or tab problem. i took a s7 tab and i am noticing that there is a sea of difference between software and support. i will not touch xiaomi products anymore
joaojunior said:
Hi! I'm having exactly the same problem. Firmware update error and then with "K81 CS(DFU)".
Did anyone manage to solve it?
Click to expand...
Click to collapse
I found the solution for me here .. its about the contacts and location permissions.
Xiaomi Smart Pen firmware update error
Good evening all, From 2 days I'm trying to update my Smart Pen, but always I got an error. Also I was looking on xiaomi.cn but method with turning on and off WiFi and Bluetooth location doesn't work. Maybe somebody here met this problem too...
forum.xda-developers.com
kvanlier said:
I found the solution for me here .. its about the contacts and location permissions.
Xiaomi Smart Pen firmware update error
Good evening all, From 2 days I'm trying to update my Smart Pen, but always I got an error. Also I was looking on xiaomi.cn but method with turning on and off WiFi and Bluetooth location doesn't work. Maybe somebody here met this problem too...
forum.xda-developers.com
Click to expand...
Click to collapse
Thanks, but this solution is for those who can connect the pen but cannot update the firmware.
In my case, the pen doesn't even connect to the tablet anymore, so I can't change the contact sharing permissions.
Hey guys so I tried multiple message and I finally got it working.
I reseted the Bluetooth and Wi-Fi preferences.
I tried to hold the front button for 10 seconds.
I tried holding the back button for 10 seconds.
I called xiaomi support and they told me to reset the Bluetooth on Wi-Fi preferences and so I did that. Then I got a notification that my xiaomi pen update was complete and I noticed that now it was connected to my tablet.
Anyone else who didn't have luck by their side?
Still have the same problem. Showing k81 C's after update my miui to 13.1.3. any other suggestion what to do to fix it
how to solve this problem k81cs(dfu)
I got the same problem with the pen who appears as K81 CS(DFU), i'm trying a lot of things, but nothing works. If anyone got an other tip :/
I keep getting please chatge your stylus now eveen after 100% fix this so annoying
Same problem.
Mi Pad 5 global version 13.1.5
Mi Smart Pen was purchased from Amazon.de - and recently turned with "K81 CS(DFU)" issue.
There is no way to update the firmware as the firmware update is disabled. Attaching and detaching pen reports "Charge your stylus now" so there is some communication going on between both devices.
I've used the service and feedback to send the logs. Tried all workarounds described on XDA forums, nothing seems to help.
there is a lsposed module named maxmipad it removes bluetooth authentication so try it i dont have the pen
Related
my phone dropped ,then after turning it on its now stuck with the flip screen cover, i've tried resetting it to factory def. still stuck ..ive tried to sideload a diff firmware but it say signature verification failed, im so lost someone help me..
similar...
dughot01 said:
my phone dropped ,then after turning it on its now stuck with the flip screen cover, i've tried resetting it to factory def. still stuck ..ive tried to sideload a diff firmware but it say signature verification failed, im so lost someone help me..
Click to expand...
Click to collapse
Similar issue, mine dropped and I had hell getting it to work again. Anyway, at a fresh rom install setup the screen would randomly flash off and on to the Cover view and regular view. Once I got past the lengthy initial setup process I cleared the option for asus cover and it was usable EXCEPT my display does not auto timeout anymore. So I'm hunting the forum for similar problems and seeing yours. Maybe the drop did something to the magnet or magnet sensor? TRying to see if it can be reset or re-calibrated.
Did you find a fix?
sumean said:
Similar issue, mine dropped and I had hell getting it to work again. Anyway, at a fresh rom install setup the screen would randomly flash off and on to the Cover view and regular view. Once I got past the lengthy initial setup process I cleared the option for asus cover and it was usable EXCEPT my display does not auto timeout anymore. So I'm hunting the forum for similar problems and seeing yours. Maybe the drop did something to the magnet or magnet sensor? TRying to see if it can be reset or re-calibrated.
Click to expand...
Click to collapse
Did you find a solution? I have the same issue.
so did anyone find a solution?
Looks like there's not solution
Did you found any solution ??
Solution for Zenfone 5 FlipCover stuck
Hello i have a zenfone 5 and get in same problem FlipCover stuck lock the screen !!'
Solution working for me !! that i boot to the recovery mood ((twrp)) should be installed or you can install it by booting into bootloader and Flash recovery !! So in recovery mode First go to Mount and check next to System ! then go back till Advanced then File Manger in file manger Scroll down till System/Priv-app/FlipCover.apk
for me i delete the fille FlipCover.apk then go back reboot system and the lock screen will be gone ! dont know if Zenfone 2 have the same steps in Custom room but i guess yea .. hope this gonna help some one stuck in this issue . Sorry for my bad English ^_^¨
Solved
dughot01 said:
my phone dropped ,then after turning it on its now stuck with the flip screen cover, i've tried resetting it to factory def. still stuck ..ive tried to sideload a diff firmware but it say signature verification failed, im so lost someone help me..
Click to expand...
Click to collapse
Remove all screws, remove sim cards connector and put it back in ( the one between battery connector and display connector). That will solve the problem with flip cover circle. Any issues contact me fb: joe hip, e-mail, [email protected].
Hello, I used Asus Zenfone 2 and got it stuck on flip cover scene too. Tried what joe hip said and attempted to reboot too but failed. I then drop it (without force) to the tiled floor from 30 cm height. And after that it's cured and screen back to normal. Feel free to try.
check this thread for solution
https://forum.xda-developers.com/ze...ode-haptic-t3283265/post73658229#post73658229
Guys, this solution worked for me. Tried dropping the phone first with from approx. 30 cm, three times and it didn't work. Then I dropped it from 5 cm higher each time and a little tilted so it doesn't fall flat on the screen -- IT WORKED!! This is the best solution. Oh, and try it on a carpet (thin carpet on hard floor). Disclaimer - I take no guarantees, up to you if you want to try these steps. Thank you very much vivavera, you saved me plenty of time (and I really needed my phone to work because was in deep ****t, God bless man).
i had the same problem
I had the same problem and I solved just with a magnet on the left bottom side of my zenfone 3.
Hi guys.
I reset my pixel C today, and started fresh, but my keyboard isnt pairing with the tablet...... When attached, the prompt appears to turn on BT, but the numbers requried to pair never appear, plus, when manually pairing, it just seems to time out, no numbers appear either.
Have reset tablet again, have also reset network settings, and have also tried to pair the keyboard with another device - same behaviour, time out.
Is there a hard reset available for the keyboard?
If you can pair to any other BT device then flat battery in keyboard? I've no idea how you can tell!
i use to own the folio but have sent it back. i'm not aware of a hardware reset on keyboard. however, i also had this problem and became frustrated so i just turned bluetooth off but kept the keyboard attached for about a day. the tablet had been rebooted a couple times. when i had become calm enough to turn it on i was greeted with a paired keyboard. it may have had something to do with a battery in keyboard not charing because it was not attached for a few days.
Ok, so, I had another pixel c keyboard at work (my original one, dropped it on the plane, lost 2 keys, so I ordered my current one about 2 months back). and even though that has been off for 2 months, it paired up, first time.....
So the tablet must be working fine....just seems the "current" keyboard doesnt want to re-pair.
Almost tempted to swap the missing keys onto the old one.....just afraid I'd screw that up
sephstyler said:
Ok, so, I had another pixel c keyboard at work (my original one, dropped it on the plane, lost 2 keys, so I ordered my current one about 2 months back). and even though that has been off for 2 months, it paired up, first time.....
So the tablet must be working fine....just seems the "current" keyboard doesnt want to re-pair.
Almost tempted to swap the missing keys onto the old one.....just afraid I'd screw that up
Click to expand...
Click to collapse
Anyways, Contacted google this morning. RMA on its way
is the new one working? i'm having the same issue
peterk-1 said:
If you can pair to any other BT device then flat battery in keyboard? I've no idea how you can tell!
Click to expand...
Click to collapse
That would be my first guess.
I lost my keyboard after the 7.0 upgrade. I am not sure, but I don't think I ever had keyboard after that. I have done hard reboots and "forgot" the keyboard along with every other BT device. Then I pair, key in the six digit number <ENTER> and it sits there saying Connecting... forever.
I bought mine in early June(Pixel and keyboard). It is not rooted and stock. Who is the to call about this?
SpringerRider said:
I lost my keyboard after the 7.0 upgrade. I am not sure, but I don't think I ever had keyboard after that. I have done hard reboots and "forgot" the keyboard along with every other BT device. Then I pair, key in the six digit number <ENTER> and it sits there saying Connecting... forever.
I bought mine in early June(Pixel and keyboard). It is not rooted and stock. Who is the to call about this?
Click to expand...
Click to collapse
I contacted tech support. They had me go to safe mode and pair and connect to keyboard. No change.
But then he asked if I could give him the serial number of the keyboard. I removed it from the tablet to search. Of course, there is no SN on the keyboard but I did find it on the box. While re-attaching the keyboard, it CONNECTED for the first time in days!!!! I rebooted in normal mode and it still worked. I unpaired and re-paired and it connected immediately.
I had the tech cancel the RMA for now.
I'm having this issue after returning to 7.1.2 from the Android O beta. Contacted support they were baffled. Keyboard out of warranty so no go on an RMA. Doesn't connect to my pixel or pixel c says incorrect passkey but never gives an option to enter one.
Try this, I finally got mine working after probably more than a year of not working at all... https://forum.xda-developers.com/pixel-c/help/finally-fix-bluetooth-keyboard-pairing-t3647393
---------- Post added at 10:45 PM ---------- Previous post was at 10:45 PM ----------
sephstyler said:
Hi guys.
I reset my pixel C today, and started fresh, but my keyboard isnt pairing with the tablet...... When attached, the prompt appears to turn on BT, but the numbers requried to pair never appear, plus, when manually pairing, it just seems to time out, no numbers appear either.
Have reset tablet again, have also reset network settings, and have also tried to pair the keyboard with another device - same behaviour, time out.
Is there a hard reset available for the keyboard?
Click to expand...
Click to collapse
neonlite said:
is the new one working? i'm having the same issue
Click to expand...
Click to collapse
SpringerRider said:
I contacted tech support. They had me go to safe mode and pair and connect to keyboard. No change.
But then he asked if I could give him the serial number of the keyboard. I removed it from the tablet to search. Of course, there is no SN on the keyboard but I did find it on the box. While re-attaching the keyboard, it CONNECTED for the first time in days!!!! I rebooted in normal mode and it still worked. I unpaired and re-paired and it connected immediately.
I had the tech cancel the RMA for now.
Click to expand...
Click to collapse
mwl1119 said:
I'm having this issue after returning to 7.1.2 from the Android O beta. Contacted support they were baffled. Keyboard out of warranty so no go on an RMA. Doesn't connect to my pixel or pixel c says incorrect passkey but never gives an option to enter one.
Click to expand...
Click to collapse
Try this, I finally got mine working after probably more than a year of not working at all... https://forum.xda-developers.com/pixel-c/help/finally-fix-bluetooth-keyboard-pairing-t3647393
Hi,
yesterday while using the watch I got the message "shutting down". The battery was flat and after charging the watch got stuck on the four moving boot symbols. To cure this I have tried both software repair and update using the Experia companion. I have as well tried resetting to factory settings using the watch own recovery but all to no avail. Can anyone please help me how to proceed from here?
baronimus said:
Hi,
yesterday while using the watch I got the message "shutting down". The battery was flat and after charging the watch got stuck on the four moving boot symbols. To cure this I have tried both software repair and update using the Experia companion. I have as well tried resetting to factory settings using the watch own recovery but all to no avail. Can anyone please help me how to proceed from here?
Click to expand...
Click to collapse
In the recovery log it says in the beginning: couldn't find tzdata for local time, GMT!, posixrules!
baronimus said:
In the recovery log it says in the beginning: couldn't find tzdata for local time, GMT!, posixrules!
Click to expand...
Click to collapse
I now installed twrp and flashed SWR50_6.0.1_MWD49B This was successful but the watch is still stuck on the four symbols. I'm outta clues please help anyone
baronimus said:
I now installed twrp and flashed SWR50_6.0.1_MWD49B This was successful but the watch is still stuck on the four symbols. I'm outta clues please help anyone
Click to expand...
Click to collapse
I had the same issue and responded on your partition likeness. I can only get mine back to LP. I have tried the above ROM and several others to no avail. If you happen to get yours going again, please advise the steps you took...and I'll do the same.
Will do
baronimus said:
Will do
Click to expand...
Click to collapse
Did you ever get yours to fully boot to MM? I have since tried other methods and am still stuck on the 4 dots / symbols. LP still runs fine, but would like to get it to MM.
I did not unfortunately. Mine works fine on LL except for gestures. It does not update automaticly which is good, since MM gives four dots. Why it doesn't work beats me.
All the best
baronimus said:
I did not unfortunately. Mine works fine on LL except for gestures. It does not update automaticly which is good, since MM gives four dots. Why it doesn't work beats me.
All the best
Click to expand...
Click to collapse
Same here. Thanks for the response. I was wondering if you somehow got it to work. I have tried a couple other ROMs to no avail. I'm quite sure if the experts had the watch, they could figure it out, but when theirs do not act like mine (ours), it may be hard for them to reproduce a fix. Anyway, LP works fine and does quite well with the battery also...so, it is fine.
golfnut22 said:
Same here. Thanks for the response. I was wondering if you somehow got it to work. I have tried a couple other ROMs to no avail. I'm quite sure if the experts had the watch, they could figure it out, but when theirs do not act like mine (ours), it may be hard for them to reproduce a fix. Anyway, LP works fine and does quite well with the battery also...so, it is fine.
Click to expand...
Click to collapse
Hmmm right now I believe my watch is fatally damaged. It rapidly loses power (100% to 0% in a couple of minutes) when connecting to the smartphone. I think my (perhaps your) problems arise from a physically damaged watch. I think the battery is damaged and perhaps also the HDD probably due to moist having entered the watch. My problem started after a swim.
Best of luck with your watch, I think mine goes to scrap
baronimus said:
Hmmm right now I believe my watch is fatally damaged. It rapidly loses power (100% to 0% in a couple of minutes) when connecting to the smartphone. I think my (perhaps your) problems arise from a physically damaged watch. I think the battery is damaged and perhaps also the HDD probably due to moist having entered the watch. My problem started after a swim.
Best of luck with your watch, I think mine goes to scrap
Click to expand...
Click to collapse
Oh, sorry to hear that. Right now, I can get a solid 2 days of battery life with just having bt and reviewing notifications. I hope it does not go your route, but thanks for the heads up. Several times I had to wait until mine fully discharged before I could get it going again when I was playing around with flashing files. Anyway, I figured I was sort of lucky not bricking in since I had no clue what I was doing. So, I have just decided to let it be for now and concede to running it on LP.
I just bought a PX5 unit, which seemed to be working perfectly until I finished installing it into my car and now it has become unresponsive with a black screen and a yellow rhombus with an exclamation point in the middle (unable to upload image as new user).
If I turn off the ignition, it will turn the stereo off and the android screen briefly shows before going into sleep. None of the buttons are allowing me to get past the screen and in to android. The reset button seems to do nothing, android is definitely running in the background, just unsure as to why this screen will not close. Any ideas?
Hi, I think I saw a yellow rhombus with an exclamation point when I was installing my radio and rear view camera was not connected to the radio. I think that it is a warning about missing video signal when radio is displaying live feed from a rear view camera.
So, one explanation for your issue could be that the radio thinks you are reversing, and the rear view camera is not connected to the radio. If I understand it right, radio can switch to rear view camera display mode based on two conditions 1) canbus information 2) +12v trigger signal.
For the condition 2), you could check that nothing is unintentional connected to reverse detect wire. If that does not help, then you could perhaps try to disable reverse view feature in the configuration menu before installing the radio to the car and/or find a working canbus configuration settings.
Please notice that I'm a beginner with Android head units and your problem might well be something totally different!!
Thanks for your reply. Some of your post seems to relate to my issue definitely, I think it is linked to the rear view camera which is currently disconnected. However I am unable to get into any configuration options. None of the buttons/resets I try get me past the exclamation screen, I can only see android once I turn off my ignition when it tells me it is closing down. None of the various reset button combinations seem to do anything with my head unit either, can't seem to reset it properly. Its strange, I will reattach the camera tomorrow and see if that brings any joy. I don't know anything about this stuff myself but I am wondering if I did something to the head unit to brick the non-android side somehow.
Edit: Unfortunately reattaching the camera did not change anything.
Update. I have managed to find a way in to the Android side if I connect my phone via bluetooth to the stereo, it then lets me use the split screen function via the top bar menu to put the warning screen other screen to the side, however whenever I touch the screen or attempt to use the android interface, my stereo goes back to the warning screen, none of my inputs via the stereo buttons or the touch screen seem to be registering with the Android side? Very confused. I have also tried as many button combination resets I can find and I have not been able to successfully get into the recovery menu, or any change except rebooting.
Was your unit professionally installed?
Also, what did the re-seller suggest when you contacted them for support?
No the unit was not professionally installed. I am not sure how I've become stuck with the problem. I made some minor changes in factory settings but nothing I thought would of caused this. The seller is yet to respond and its been a couple of days, but I have requested the hardware reset methods for this unit or any other solutions.
deano35 said:
No the unit was not professionally installed. I am not sure how I've become stuck with the problem. I made some minor changes in factory settings but nothing I thought would of caused this. The seller is yet to respond and its been a couple of days, but I have requested the hardware reset methods for this unit or any other solutions.
Click to expand...
Click to collapse
Check the reverse wire on the back of the unit...if necessary disconnect it to ensure no reverse signal is received.
If your unit can boot into android normally then you will have to figure out why the reverse wire is receiving signal .
Check your connectors to avoid any of them to be loose.
Enviado desde mi SM-G950F mediante Tapatalk
Everything has been disconnected from the unit except the power cable to car and and canbus, from what I can tell nothing is loose. Unit will not boot without the canbus box whatsoever, not sure if that is meant to happen.
deano35 said:
Everything has been disconnected from the unit except the power cable to car and and canbus, from what I can tell nothing is loose. Unit will not boot without the canbus box whatsoever, not sure if that is meant to happen.
Click to expand...
Click to collapse
Yes, canbus decoder need to be connected for power up the HU. If you dont need the decoder box you need rewire the harness.
I think I am going to have to request a refund and return it. Still no reply from the reseller and I am not sure what else I can try, everything that is not needed to power it has now been removed. I can't send links or else I would update the thread with a video of the touch/physical buttons being completely unresponsive even when I manage to get to Android. The unit has definitely developed a fault and I am unable to reset it. Admittedly it could be my fault somehow as it was working for the first few boots, but unless they give me something to try I am just going to have to send it back.
Quick bump. Has anyone got any further ideas? I bought off Aliexpress so contact with the seller is slow and painful, they do not seem to understand the issue and just keep telling me to disconnect all wires and reconnect. Which has been done many times. If anyone wants to post a link to the video for me I would be happy to send them it privately.
deano35 said:
Quick bump. Has anyone got any further ideas? I bought off Aliexpress so contact with the seller is slow and painful, they do not seem to understand the issue and just keep telling me to disconnect all wires and reconnect. Which has been done many times. If anyone wants to post a link to the video for me I would be happy to send them it privately.
Click to expand...
Click to collapse
I would start a dispute with them. I had a device that they sent with similar problems and plenty of issues, which they would not help with or would not understand. Best option is to dispute to get a new device or a full refund. Could you send the video?
xLeviNx said:
I would start a dispute with them. I had a device that they sent with similar problems and plenty of issues, which they would not help with or would not understand. Best option is to dispute to get a new device or a full refund. Could you send the video?
Click to expand...
Click to collapse
Yeh I have a dispute open currently, just was hoping it would inspire the seller to actually offer up a working way of resetting the device. Had to add link below seperately as needed to be ten or most posts.
https://www.youtube.com/watch?v=ujHacKESAT8&feature=youtu.be
The stereo defaults as the warning image black screen and I can only get android up using the multiwindow button with a long press. Then the android side will not register any input and will keep trying to put the black screen to the front.
Update: I have been told by Aliexpress I can have a partial refund and keep the unit, or a full refund if I return to China. Anyone have any ideas how I would go about resetting the unit if I took the partial refund? To be honest I think my only option is to return it and get the full amount back but any ideas would be welcome! Shipping to China and awaiting a refund is going to take weeks, would rather just get it working if possible.
deano35: any progres? I have the same problem as you. This is my post from PX5 MTCD/E Head Unit Discussion Thread
" Hi , I have https://s.click.aliexpress.com/e/DtwdJIt its px5, Mtce_gs_v2.90c. Now I have a little problem with rear camera. I bought reverse camera and tried to connect it into front camera input(I was curious how it would look like) and since then its stuck on camera view. Even after disconnecting camera. Only solution was disable "prohibit reverse" in factory settings menu, but with "prohibit reverse" disabled is obviously not showing reverse camera when I gear the reverse down. Everything is shown in this video. https://photos.app.goo.gl/XbYUHApzT8qTezkq6 Thanks for any advice. "
Take a look on the video, its similar as yours.
Hello Guys,
So, i bought a Xiaomi Smart Pen for mi Xiaomi Mi Pad 5, and i changed region to South Korea and tried connect the pen and its works,
then I updated the pen's firmware and put it to download the MIUI update, however the firmware update didn't work and the pen stopped working, I saw on the forum that it should erase all devices connected to bluetooth, so I disconnected the Xiaomi connection Smart Pen and it was a K81 CS(DFU) since then I can't connect my pen anymore, I've done a hard reset but it doesn't go back to the factory settings, it just erases the data, I've tried everything but it doesn't work...
When I try to connect to the K81 CS(DFU) the following message appears "Could not pair with K81 CS(DFU) because the PIN is incorrect".
When I put the pen on the side of the tablet and remove it, the following message appears in a pop-up "charge your stylus now", I've left it all night charging on the tablet but nothing changes.
Will it work if I put a Room from version 12.5 of MIUI and try to connect again?
Has anyone with this problem been able to solve it?
NOTE: The Xiaomi Smart Pen no longer appears in bluetooth, only the K81 CS(DFU).
Thanks in advance.
OBS: XIAOMI MI PAD 5 GLOBAL VERSION
Hi! Any update regarding this issue? Thanks.
I have very the same issue. My Pad 5 is updated to the latest 13.1.3.0. no notification to connect to the pen just "charge your stylus now"
geomancer_86 said:
I have very the same issue. My Pad 5 is updated to the latest 13.1.3.0. no notification to connect to the pen just "charge your stylus now"
Click to expand...
Click to collapse
i have the same problems to, my pen dont work after i'm updating my miui to 13.1.3. any hint what to do?
how to solve this problem
I think there's a Bug in the lastest Update/ Firmware.
My Xiaomi Keyboard can't connect anymore
geomancer_86 said:
I have very the same issue. My Pad 5 is updated to the latest 13.1.3.0. no notification to connect to the pen just "charge your stylus now"
Click to expand...
Click to collapse
Mine 2
update: it was a new pen so I returned it and replace it with another new pen. the new pen works even updated to the latest firmware