Hi,
yesterday while using the watch I got the message "shutting down". The battery was flat and after charging the watch got stuck on the four moving boot symbols. To cure this I have tried both software repair and update using the Experia companion. I have as well tried resetting to factory settings using the watch own recovery but all to no avail. Can anyone please help me how to proceed from here?
baronimus said:
Hi,
yesterday while using the watch I got the message "shutting down". The battery was flat and after charging the watch got stuck on the four moving boot symbols. To cure this I have tried both software repair and update using the Experia companion. I have as well tried resetting to factory settings using the watch own recovery but all to no avail. Can anyone please help me how to proceed from here?
Click to expand...
Click to collapse
In the recovery log it says in the beginning: couldn't find tzdata for local time, GMT!, posixrules!
baronimus said:
In the recovery log it says in the beginning: couldn't find tzdata for local time, GMT!, posixrules!
Click to expand...
Click to collapse
I now installed twrp and flashed SWR50_6.0.1_MWD49B This was successful but the watch is still stuck on the four symbols. I'm outta clues please help anyone
baronimus said:
I now installed twrp and flashed SWR50_6.0.1_MWD49B This was successful but the watch is still stuck on the four symbols. I'm outta clues please help anyone
Click to expand...
Click to collapse
I had the same issue and responded on your partition likeness. I can only get mine back to LP. I have tried the above ROM and several others to no avail. If you happen to get yours going again, please advise the steps you took...and I'll do the same.
Will do
baronimus said:
Will do
Click to expand...
Click to collapse
Did you ever get yours to fully boot to MM? I have since tried other methods and am still stuck on the 4 dots / symbols. LP still runs fine, but would like to get it to MM.
I did not unfortunately. Mine works fine on LL except for gestures. It does not update automaticly which is good, since MM gives four dots. Why it doesn't work beats me.
All the best
baronimus said:
I did not unfortunately. Mine works fine on LL except for gestures. It does not update automaticly which is good, since MM gives four dots. Why it doesn't work beats me.
All the best
Click to expand...
Click to collapse
Same here. Thanks for the response. I was wondering if you somehow got it to work. I have tried a couple other ROMs to no avail. I'm quite sure if the experts had the watch, they could figure it out, but when theirs do not act like mine (ours), it may be hard for them to reproduce a fix. Anyway, LP works fine and does quite well with the battery also...so, it is fine.
golfnut22 said:
Same here. Thanks for the response. I was wondering if you somehow got it to work. I have tried a couple other ROMs to no avail. I'm quite sure if the experts had the watch, they could figure it out, but when theirs do not act like mine (ours), it may be hard for them to reproduce a fix. Anyway, LP works fine and does quite well with the battery also...so, it is fine.
Click to expand...
Click to collapse
Hmmm right now I believe my watch is fatally damaged. It rapidly loses power (100% to 0% in a couple of minutes) when connecting to the smartphone. I think my (perhaps your) problems arise from a physically damaged watch. I think the battery is damaged and perhaps also the HDD probably due to moist having entered the watch. My problem started after a swim.
Best of luck with your watch, I think mine goes to scrap
baronimus said:
Hmmm right now I believe my watch is fatally damaged. It rapidly loses power (100% to 0% in a couple of minutes) when connecting to the smartphone. I think my (perhaps your) problems arise from a physically damaged watch. I think the battery is damaged and perhaps also the HDD probably due to moist having entered the watch. My problem started after a swim.
Best of luck with your watch, I think mine goes to scrap
Click to expand...
Click to collapse
Oh, sorry to hear that. Right now, I can get a solid 2 days of battery life with just having bt and reviewing notifications. I hope it does not go your route, but thanks for the heads up. Several times I had to wait until mine fully discharged before I could get it going again when I was playing around with flashing files. Anyway, I figured I was sort of lucky not bricking in since I had no clue what I was doing. So, I have just decided to let it be for now and concede to running it on LP.
Related
Hi Forumers,
I've just bought the t800.
After a couple of days I've tried to use the bluetooth and oddly it cant find anything.
I've made sure I've got a few bluetooth items on in the room, and my phone and laptop can find them but my Tablet cant.
But, my phone was able to find the tablet and the two paired that way.
But since my tablet cant find my bluetooth speaker, its a tad rubbish..
Any ideas on how to fix?
Thanks in advance
I have a Bluetooth speaker and sometimes I have to restart the speaker or forget the speaker in order to connect to it.I would suggest (on your tab s) going into the bluetooth setting and check, make device visable to other devices. Hope this helps.
Sent from my SM-T800 using Tapatalk
okey dokey,
So Ive restarted my speaker, laptop phone and stereo bluetooth receiver, and nothing is showing to the tablet, so it seems not to be that.
the tablet is visible to my phone, so that part works.
but my tablet cant see anything.
Plan B?
kuztardd said:
okey dokey,
So Ive restarted my speaker, laptop phone and stereo bluetooth receiver, and nothing is showing to the tablet, so it seems not to be that.
the tablet is visible to my phone, so that part works.
but my tablet cant see anything.
Plan B?
Click to expand...
Click to collapse
Might try a factory reset. Right after I bought my T800 the wifi greyed out and refused to work. Did a reset and all was fine again.
Argh, I had just spent hours installing stuff.. but seems it may be the only answer!
Bu99er! :-/
Should I do anything special before a hard reset?
kuztardd said:
Argh, I had just spent hours installing stuff.. but seems it may be the only answer!
Bu99er! :-/
Should I do anything special before a hard reset?
Click to expand...
Click to collapse
I wouldn't, but I never keep anything on my tablet of importance.
I brought the tablet to work so I could sort it out in work hours.
I was in the process of hitting the reset button and paused, and decided to try once more..
and now it works.
not sure what happened over night to make it work.. odd!?
kuztardd said:
I brought the tablet to work so I could sort it out in work hours.
I was in the process of hitting the reset button and paused, and decided to try once more..
and now it works.
not sure what happened over night to make it work.. odd!?
Click to expand...
Click to collapse
...and we all lived happily ever after.
T805 Bluetooth not works
Hi to all
I bouth some days ago a tab s 10.5 and in the first days the bluetooth works, but now I cannot activate.
I have already done a factory reset but nothing happened, so it does not works.
can anyone help me?tab is rooted
thanks
Giorgio
Just got the S6 Edge today. I installed smart switch and follow all steps layer out in another thread here. I keep getting stuck at 51% when it says it's downloading. Anyone else having same problem?
Farva0412 said:
Just got the S6 Edge today. I installed smart switch and follow all steps layer out in another thread here. I keep getting stuck at 51% when it says it's downloading. Anyone else having same problem?
Click to expand...
Click to collapse
I think it's an error work smart switch, it worked for me yesterday and today everyone's is getting stuck at 51%.
Farva0412 said:
Just got the S6 Edge today. I installed smart switch and follow all steps layer out in another thread here. I keep getting stuck at 51% when it says it's downloading. Anyone else having same problem?
Click to expand...
Click to collapse
U could just download the full firmware and flash thru odin
Lancerz said:
I think it's an error work smart switch, it worked for me yesterday and today everyone's is getting stuck at 51%.
Click to expand...
Click to collapse
Same here, worked fine for me a couple days ago and now just stalls at 51%
Anyone able to get past 51%?
I just tried the smart switch, the first time it got stuck at 51%. After awhile I just hit cancel and tried again, got all the way to 85 and seemed to get stuck, but I let it sit and eventually it jumped to 100%. Everything completed as it should after that.
ryan09266 said:
I just tried the smart switch, the first time it got stuck at 51%. After awhile I just hit cancel and tried again, got all the way to 85 and seemed to get stuck, but I let it sit and eventually it jumped to 100%. Everything completed as it should after that.
Click to expand...
Click to collapse
mac or pc?
PC, windows 8.1
So after doing the smart switch reinstall I can definitely say I have seen a massive improvement in battery life. 6 hours into the day, at 89% and cell standby is at 1%. Before my battery would be in the 70s by now, and cell standby 8-9%. My advice keep trying smart switch if it isn't working for you.
still stuck windows 8.1 64bit.. tried flashing firmware through odin, tried using smart switch in recovert mode and normal mode.. any other ideas? I'm gonna try a windows 7 machine tonight. This just sucks, think I'm gonna call tmobile for another replacement.
I just got my brand new OP3, opened it and turned it on to start setting it up, it freezes inside the android set up and then restarts itself after a few seconds of being frozen.
Any solutions? I really don't want to return it, I find it a bit stupid it doesn't even work out of the box
Might be a dud. They happen. RMA it.
LaysDarren said:
I just got my brand new OP3, opened it and turned it on to start setting it up, it freezes inside the android set up and then restarts itself after a few seconds of being frozen.
Any solutions? I really don't want to return it, I find it a bit stupid it doesn't even work out of the box
Click to expand...
Click to collapse
I don't own this phone, but this happened to me with a Nexus, I turned it off, was able to get into recovery mode with button combinations, then I factory reset, cleared cache, and rebooted, it was fine.
I hope you can give it a try
Sent from my XT1097 using XDA-Developers mobile app
mr mystery said:
Might be a dud. They happen. RMA it.
Click to expand...
Click to collapse
markdexter said:
I don't own this phone, but this happened to me with a Nexus, I turned it off, was able to get into recovery mode with button combinations, then I factory reset, cleared cache, and rebooted, it was fine.
I hope you can give it a try
Click to expand...
Click to collapse
Tried doing the Factory reset thing, no luck. Talked to OP support and the guy told me to submit a ticket with my issues, and that a "level 2 technician" would help me.
So I got home and plugged it into my PC, turns out the phone doesn't freeze when plugged in via USB. But on the included charger, and without being plugged into anything, it freezes and reboots itself in a continuous loop.
Keep us informed I'd like to hear what the problem/solution is
Hello, i have the same issue, did u find the solution ?
tenzeu said:
Hello, i have the same issue, did u find the solution ?
Click to expand...
Click to collapse
I also had my Oneplus 3 in a bootloop and freezing while showing either the 1+ square or the rotating red dots.
After I tried to get it repaired by talking with support and had been using my old phone for a few days and reflashing the ROM and recovery many times. I got it working again (ish) now it only freezes ones a day.
Support is a pain, I'm waiting for a level 2 techician for almost a week now.
So I any of you know a solution or have a confirmation that it is a hardware failure, I think we all would like to hear about it.
Malfunctioning on Marshmallow update from Samsung.
I was going to install Cyanogen OS, but haven't yet.
The update from Samsung to M 6.0.1 seemed to go ok.
But, now I have errant screen touches, abrupt restarts for no apparent reason, and white streaks flashing on the display (intermittent).
It works fine for a few hours, then wacky again.
Is there anything that I can do?
This is the 8.4 WiFi only version. TM-7400 I believe.
No apparent damage to the display, no water damage recently, or ever.
Thanks!
I just now booted in safe mode. Seems to be working OK, but it has worked OK for hours after having the glitches the past couple of days.
Should I remove the SD card? Maybe an app on there is the problem?
What apps do you have? Use this and post a list.
http://www.onyxbits.de/listmyapps
Anyone?
I updated the few remaining apps which required it, and it's run fine since my OP.
I just now saw a white streak on the display, and a few seconds later it restarted by itself.
Thanks.
And, how much time involved in flashing Cyanogen Mod for a first time ever having done it?
Sorry, I didn't see this reply. I'll post apps list shortly..
TY.
steamrollerpark said:
What apps do you have? Use this and post a list. I'm using a different device, presently to post here.
I'll log in on affected device, of I can.
http://www.onyxbits.de/listmyapps
Click to expand...
Click to collapse
What you need to do to fix this is:
Open tablet. Pull battery out for 3 minutes , pop it back in. Close tablet, your tablet will be fixed
Removing the battery is not only troublesome but seems a little unnecessary.
You should try formatting all partitions through TWRP and reflashing the 6.0.1 firmware using Odin. I did that and have no issues with my device.
The 3 symptoms this dude has are what the battery issue have. Pulling the battery and getting into the inside are not difficult with the correct tools from Amazon or eBay and tutorials from YouTube. This fix has worked with my gfs tab s
suburbadroid said:
The 3 symptoms this dude has are what the battery issue have. Pulling the battery and getting into the inside are not difficult with the correct tools from Amazon or eBay and tutorials from YouTube. This fix has worked with my gfs tab s
Click to expand...
Click to collapse
While removing the battery can be a good idea for removing leftover electricity from the circuits and probably fixing those issues, if not careful can end up breaking some component.
He said when booting the device in safe mode all issues disappeared, so flashing the stock rom using Odin probably will solve all problems.
Hi everyone,
I'm experiencing pretty silly situation with my phone.
So the story begins here:
I was surfing the web while listening to music in the bus when suddenly my oneplus3 randomly turned off and I couldn't turn it back on. (I was on something around 15% on battery so it's not a low battery problem) I tried to turn it on several times and after holding the power button for like 10secs it turned on, and after pressing the power button again (because I needed to get past unlocked bootloader screen and dm-verity) I saw a boot screen. The capacitive button leds turned on and after 3 secs it turned off again, so I started worrying... After a while I tried to access the recovery, but no luck at all. It powers it self off after bootscreen. So I started to research. Tried to flash the entire OS, partritions with msmdownload tool. After several unsuccessful flashes (firehosewritedata failed sometimes while writing userimg or system.img or boot.img) I did get the download complete green text message, and after successful flash, the white LED turned on, even the phone was not plugged in USB or charger and turned off. The screen is completely black and the white led just flashes constantly without blinking or anything. I could only turn the led off by pressing the power button for another 10 secs. And after turning the phone off, problem still remains. After oneplus logo phone shuts down...
I can access bootloader.
And after flashing everything should be on stock, because now I only got screen only about bootloader, no dm-verity..
And of course - I still cannot access the recovery.
p.s. I tried to do the power cycle (as the tech support told me) but still no luck at all.
did u tried the full msmdownload tool (1gb) or the 55mb version ?
Mukthar. said:
did u tried the full msmdownload tool (1gb) or the 55mb version ?
Click to expand...
Click to collapse
1GB version
djemm1996 said:
1GB version
Click to expand...
Click to collapse
Are you sure that you did it right? Did your phone show up as mentioned in the instructions?
Puddi_Puddin said:
Are you sure that you did it right? Did your phone show up as mentioned in the instructions?
Click to expand...
Click to collapse
Of course. Everything is done right. I also get that green "download complete" message.
p.s I also opened the phone. water indicators are fine and no major defects what can i see by eye... All connectors are good as well.
Puddi_Puddin said:
Are you sure that you did it right? Did your phone show up as mentioned in the instructions?
Click to expand...
Click to collapse
And yes, phone was connected right. :good: installed drivers with test mode on Win10 and got Snapdragon device in COM devices. As well the MsmDownload tool shows up my device in port #20
Any ideas?
djemm1996 said:
Any ideas?
Click to expand...
Click to collapse
Follow method 2 from the Hard Brick guide by Naman Bhalla and try two or three times.
Sometimes it takes more than once for restoration.
Since you opened the phone, i think your warranty is gone now.
If the msmdownloadtool didnt help you, there is nothing you can do i think.
try to flash again, and if it still maybe something short inside.
if you have disassembly your phone, try disconnecting various flex cable like camera, sim slot etc that connect to the mainboard, that doesn't prevent device from powered on, then try to turning it on.
if it still, check your mainboard, if you don't know how, send it back.
AcidNoteZ said:
Since you opened the phone, i think your warranty is gone now.
If the msmdownloadtool didnt help you, there is nothing you can do i think.
Click to expand...
Click to collapse
Is ir really gone? There is a still warranty void sticker on the screw there, but of course it's possible to see by eye that the phone has been opened.
I have an appointment with Level2 tech support @oneplus, they are going to remotely flash the entire OS, but do you think they are using pretty similar technique as the msmdownloadtool?
djemm1996 said:
Is ir really gone? There is a still warranty void sticker on the screw there, but of course it's possible to see by eye that the phone has been opened.
I have an appointment with Level2 tech support @oneplus, they are going to remotely flash the entire OS, but do you think they are using pretty similar technique as the msmdownloadtool?
Click to expand...
Click to collapse
They are doing the same thing like you did.
I already had a session since i thought they are going to do something "special"
You can try the remote session but im afraid that wont help you if you already did it multiple times.
What about battery? Charged?
drmuruga said:
What about battery? Charged?
Click to expand...
Click to collapse
Yes battery is charged of course. It's just doint the same thing. Turns on, after a while when bootscreen comes it just turns off and white notification led appears, after that nothing.
I tried to flash it with tool using method 2 for like 15 times with "download complete" messages, but still no luck at all. Tried to erase partritions with fastboot, flashing just only recovery, modded recovery etc. but I still cannot access the recovery nor system. I just don't get it why the phone does not boot into recovery if I flash it or boot it straight away, It just only turns off and that's it. nothing more. Only black screen and white led lighting all the time (after a while the phone turns warm).
I have read all the MsmDownloadTool thread in "Mega Unbrick thread" and saw that few people have experienced the very same situation as me, so I was wondering if there is any fix for this? It's so strange that I was just surfing the Web and it just turned off by it self with like static image for miliseconds and after that just black screen.
There should be any fix. I guess that it's just a partition error...
Ok, not good news. I had a little remote session before a while. They says it's already a hardware problem.
AcidNoteZ said:
Since you opened the phone, i think your warranty is gone now.
If the msmdownloadtool didnt help you, there is nothing you can do i think.
Click to expand...
Click to collapse
Pfffft you think manufacturers notice when you take apart phones? Hell I took apart my Xperia Z2 because it was having problems and then glued it back together with cyanoacrylate hahahaha (worst thing to do but wtv) and no one noticed though it was seemless and everything looked perfect
Guys, I've got something for you! Not really the same thing as Naman.
p.s. not saying its original hehehehe keep safe
man i got a very similiar problem but my op3 has a black screen i was also on low battery around 5-15% when my phone went off after i was in twrp
Actually I was on twrp too! Also I have recently noticed that recovery loading speed was far too long than normal one. I'm talking for something about 5-7 minutes after reboot into twrp. So, who knows what did happen. Just made an RMA request. Will see how it goes.
Anyway, I was on stock 7.1.1 and it's just rooted with custom recovery and that's it! Nothing more! Is that just a factory failure or maybe it's caused by drops i have had? Nothing serious for a 4-5 times for a half year. Of course I have used it even in winter when the snowflakes are coming down from the sky and little rain. Btw, these liquid indicators are white, so all safe. ::laugh:
A
makadama said:
man i got a very similiar problem but my op3 has a black screen i was also on low battery around 5-15% when my phone went off after i was in twrp
Click to expand...
Click to collapse