i have been using the p3300 for a month now an it was working fine but all of a sudden i couldn't use my stylus. i tried the screen allignment but the screen didnt respond so i restarted the device. this also didnt work. i also tried a soft reset. no results so i did a hard reset now i am stuck at the screen where it says " Tap to start your device "
Plz Help....
Hi
It sounds then like the touch function of the screen has stopped working.
If you have only had it a month depending on where you got it you may be able to return it.
Sorry about this
Cheers Dave
maybe
seems like that to me too
still i hope i wont need to
anyway thanks
no problem
Anytime
If you have not yet returned it, try taking the screen protector off if you have one on.
My screen stopped responding to touch a while back. When I took the protector off all was fine.
could be it
may be but i am not sure about it i will try it nonetheless
Thanks
screen needs rest ??
nope no use the screens gone crazy i guess
it recognises a few strokes when left for a few hours the goes dead again
maybe it need some rest
On the screen, round the edges make sure there’s no gunk under the gap between the case and screen. You will be surprised what can get under there. Flat Plastic tooth picks are good for clearing it
i am nooob
cant try it
dont really know how to remove the screen guard
cant find the seam
Hi
You might not be a Noob. You can only remove a Screen Guard/Protector if you have actually put one one.
Also i still dont think there is much you can do.
If it does work after a while it is possible that the screen calibration has gone haywire If you get chance to use it try doing that it may help
Cheers Dave
mine to same problem please help
So, I left my Artemis in my RAM Aqua Box waterproof phone case attached to my motorcycle while I ran into the store.
I came out, started the bike and started the ride home. That was when I noticed the white screen and my tunes had stopped playing. I've seen it happen before (while turning off the phone in camera mode, etc), but a simple soft reset always fixed it. Not this time...
For two days now I've flashed it back to factory, installed my latest ROM (twice), reconfigured all my settings, etc, only to have the phone seize up by fading to the White Screen Of Death. The only fix is to remove the battery and let it sit for a bit. I have found however I can get the phone to run longer if I put it in the freezer for 15 mins, then it runs as it should until it warms up.
Sometimes it will work for half a day, other times it will fade out even before the soft reset boots up again. It really doesn't like being plugged in to charge or sync.
Now for some more background info. It did get deathly hot in the case I have because it has a clear face, is sealed, and it was sunny. Also, I started the bike when the phone was plugged in. I've heard this is bad for the charging circuit, but I'm leaning to the overheating as being the seminal event of the start of my sorrows because I've started the bike/truck many times with the phone plugged in. Did my luck run out?
What have I done, and how do I fix it?
i have had a white screen problem on my phone to it would go like this when just left on or when wanting to flash it in boot mode i have taken both sim card and memory card out and i have found that the memory care is curupted and works fine now will have to formate the memory card in order for it to work properly in the phone again
htc artimis 02 orbit
Yes, you can remove your memory card.
Just had similar problem. Possible reason: ROM update. Possible solution - ROM changed again (different) and hard reset. Hopefully everything will be ok. Until now (9 hours) - it is!
SCREEN
Hello
sorry i speak english a little.My TC P3300 have a problem on screen.I replace the lcd screen because the old make a hole white every 5 s.With the new its the same.What happen
thanks
I have the same Problem I started getting the White screen when i try and access anything it hangs and then goes white screen I removed the sd 2gb and left the sim in and id stil did the same thing but now i put the 4gb out of my laptop and now it seems to work but i still get the power on problem sumtimes
Im running wm 6.5 Arte_WM65_23009_WWE_Fixed_IE_b1
Any sugeustions? help plz
i have same problem
Even I was facing the same problem. I did hard reset couple if times and didn't find a solution. So finally I gave the phone to the service center and it seems now it's been fixed. I will ask the service guys about the actual problem and would post it here.
It may help someone.
Now I am going to try android on my phone, wish me luck.
Regards,
Rajesh
rajeshrr said:
Even I was facing the same problem. I did hard reset couple if times and didn't find a solution. So finally I gave the phone to the service center and it seems now it's been fixed. I will ask the service guys about the actual problem and would post it here.
It may help someone.
Now I am going to try android on my phone, wish me luck.
Regards,
Rajesh
Click to expand...
Click to collapse
Did U ask the service guy abt the screen problem
Hey guys,
My Xperia Pro has been running into some problems with the display as of late. What happens is after a short period of keeping the phone idle, it doesn't wake up. When the power button or the home button is pressed, it just shows a blueish-black screen and the lights between the physical buttons light up. Same thing happens when the keyboard is slid out. The backlight of the keys work but the screen still shows a blueish-black color. After trying again and again, the screen finally works, just to run into the same problem after locking the screen.
I tried changing the ROM and flashing a different kernel to no use. Then I finally flashed a stock Gingerbread firmware. Now the screen doesn't show any blueish-black shade or anything else at all!!!! I have currently just left my phone to charge because I don't want the battery to run out during this crisis. I have also re-booted many, many times by pulling out and re-inserting the battery.
Any suggestions and tips would be highly appreciated! Thanks in advance guys!
My Xperia Pro have the same issue . Like when unlock , no screen (black) ,
The issue I found out is having something to do with my back cover
ie. If I remove the cover and reboot , and then unlock /lock , no problem, As soon as i put the back cover , it unlocks with black screen , I was sure no kernel or fw was the reason , as i have been through diff kernels and fws /roms without an issue like this , and as soon as the black screen shows and you try to restart it wont even show the logo , so i was damn sure ,its no kernel issue , Please check this method , i will try to find the exact issue why the back cover is making this.
Update: Found out that the push made by back cover with the battery (which basically may be jamming the strip or something inside) is making the problem , It may have more to it than this ,anyway this is my phone's problem
Screen on but no display
AeonWorld said:
My Xperia Pro have the same issue . Like when unlock , no screen (black) ,
The issue I found out is having something to do with my back cover
ie. If I remove the cover and reboot , and then unlock /lock , no problem, As soon as i put the back cover , it unlocks with black screen , I was sure no kernel or fw was the reason , as i have been through diff kernels and fws /roms without an issue like this , and as soon as the black screen shows and you try to restart it wont even show the logo , so i was damn sure ,its no kernel issue , Please check this method , i will try to find the exact issue why the back cover is making this.
Update: Found out that the push made by back cover with the battery (which basically may be jamming the strip or something inside) is making the problem , It may have more to it than this ,anyway this is my phone's problem
Click to expand...
Click to collapse
I have the same problem, and back cover was not the solution for me. What should I do???
Yep the back cover is a problem!
AeonWorld said:
Update: Found out that the push made by back cover with the battery (which basically may be jamming the strip or something inside) is making the problem , It may have more to it than this ,anyway this is my phone's problem
Click to expand...
Click to collapse
That actually worked for me initially..removing the back cover and rebooting. But its not now, what ever I do I only see the dim lit LCD screen.
But yeah, I am able to unlock the phone in the blind and also hear the increase/ decrease in the volume by pressing the volume rocker and also touch and hold on the home screen to feel the vibration (guess for removing the widget or something that's already there).
So is there any solution for this, or any first aid before I get my Xperia Pro to the service centre ??
Ok guys, so I'm having an issue with my Note 10.1 2014 Edition. Whenever the screen times out, or you lock it, the screen will not come back on. The buttons will light up, but the screen is unresponsive. Hold the power button for a reboot and it reboots, screen works fine until the next lock. So obviously first thing, wiped everything, and reloaded Hypderdrive, only to get the same issue. So I go in again to recovery, and while I'm doing some research, TWRP times out and the screen goes black, and again, I'm unable to "wake" the device. Now I'm thinking hardware, but the power button is being recognized to lock it, so it should be recognized to unlock it as well and it is because the button lights come on. I've gone in, did a complete wipe including /system and /data and I'm currently trying to load a new rom to my microsd card to load, but the screen timed out again and I have to reboot the device back into recovery each time to get the screen to work. I'm pretty sure the root method I used, voided my warranty, so sending it in is probably not an option. When I reboot into download to check the status, It just says Downloading... Do not turn off target!! and I see no information in the top left of the screen. Anyone have any idea as to what could be causing the screen to do this? I'm kinda lost at this point! Thanks in advance.
P.S. So I was able to get into Download, and found my Current Binary is Custom, my System Status is Custom, and my Warranty Bit is 1, so I'd assume warranty is out of the option.
P.P.S I got a new rom loaded everything flashed fine, booted, let it set, when the screen timed out, again won't turn on. I can almost say 100% it's not a rom/Kernel issue. But beyond that I'm lost!
scoot05redss said:
Ok guys, so I'm having an issue with my Note 10.1 2014 Edition. Whenever the screen times out, or you lock it, the screen will not come back on. The buttons will light up, but the screen is unresponsive. Hold the power button for a reboot and it reboots, screen works fine until the next lock. So obviously first thing, wiped everything, and reloaded Hypderdrive, only to get the same issue. So I go in again to recovery, and while I'm doing some research, TWRP times out and the screen goes black, and again, I'm unable to "wake" the device. Now I'm thinking hardware, but the power button is being recognized to lock it, so it should be recognized to unlock it as well and it is because the button lights come on. I've gone in, did a complete wipe including /system and /data and I'm currently trying to load a new rom to my microsd card to load, but the screen timed out again and I have to reboot the device back into recovery each time to get the screen to work. I'm pretty sure the root method I used, voided my warranty, so sending it in is probably not an option. When I reboot into download to check the status, It just says Downloading... Do not turn off target!! and I see no information in the top left of the screen. Anyone have any idea as to what could be causing the screen to do this? I'm kinda lost at this point! Thanks in advance.
P.S. So I was able to get into Download, and found my Current Binary is Custom, my System Status is Custom, and my Warranty Bit is 1, so I'd assume warranty is out of the option.
P.P.S I got a new rom loaded everything flashed fine, booted, let it set, when the screen timed out, again won't turn on. I can almost say 100% it's not a rom/Kernel issue. But beyond that I'm lost!
Click to expand...
Click to collapse
So I was messing with it some more after work today and found a few more pieces to the puzzle. After rebooting it in a bright room, I found the screen is on, but the backlight isn't. The screen is usable and responsive. Second thing is the brightness slider no longer works, it's just one brightness level and can't be adjusted. I've read online, that there maybe a loose ribbon cable, so I'm going to look into that alittle bit. I'm really hoping the backlight and LCD aren't shot! Again if anyone has any experience or ideas, please let me know!
SO I was using Triangle Away to try to clear the flash counter, as I was filling out a service request form from Samsung, and after the reboot the screen was brighter. I then tried the brightness slider..it worked and locked and unlocked it and the screen came back on. IDK what fixed it (maybe Triangle Away????) but it's working now! I'm hoping it sticks! I hope no one else has this issue, but maybe this will help!
Sorry for bumping this old thread, but I have found a solution! (at least for me)
There is suprisingly little to find about this issue, so that's why I've made this quick post.
I had this issue as well, but after flashing the stock modem (NON-HLOS.bin) it was resolved. (fastboot flash modem NON-HLOS.bin)
Currently I'm on CM11S XNPH05Q with stock kernel, OnePlus One.
I think it had to do with me going back from CM12 (Lollipop-based) to CM11S (KitKat-based).
help urgently needed
awesomTNT said:
Sorry for bumping this old thread, but I have found a solution! (at least for me)
There is suprisingly little to find about this issue, so that's why I've made this quick post.
I had this issue as well, but after flashing the stock modem (NON-HLOS.bin) it was resolved. (fastboot flash modem NON-HLOS.bin)
Currently I'm on CM11S XNPH05Q with stock kernel, OnePlus One.
I think it had to do with me going back from CM12 (Lollipop-based) to CM11S (KitKat-based).[
hello awespmeTNT
i on on kitkat 4.4.2
can you please explain me stepwise how to flash stock modem to galaxy note 10.1 2014th edition SM-P601
my base band is : P601XXUCNJ1
kernel version is 3.4.39-3098518 thank u
need the help urgently
Click to expand...
Click to collapse
ranzzzit said:
hello awespmeTNT
i on on kitkat 4.4.2
can you please explain me stepwise how to flash stock modem to galaxy note 10.1 2014th edition SM-P601
my base band is : P601XXUCNJ1
kernel version is 3.4.39-3098518 thank u
need the help urgently
Click to expand...
Click to collapse
I'm sorry man, but I have no experience with the Galaxy Note 10.1 2014...
I tried to search for a solution, but I couldn't find much since there are all these different versions of the Note 10.1.
I think you have to use Odin to flash custom zips and such for your device.
I couldn't find the modem for the P601 (NON-HLOS.bin), but you could open a new thread asking for it?
I really hope you'll find a solution.
Also, have you tried a factory reset?
If you haven't done anything like rooting, flashing costom ROMs etc, your warranty shouldn't be void and you could return your device.
That's what I'd do.
Best of luck.
scoot05redss said:
So I was messing with it some more after work today and found a few more pieces to the puzzle. After rebooting it in a bright room, I found the screen is on, but the backlight isn't. The screen is usable and responsive. Second thing is the brightness slider no longer works, it's just one brightness level and can't be adjusted. I've read online, that there maybe a loose ribbon cable, so I'm going to look into that alittle bit. I'm really hoping the backlight and LCD aren't shot! Again if anyone has any experience or ideas, please let me know!
Click to expand...
Click to collapse
can you help scoot05redss
Sorry, I haven't flashed any modems to my Note 10.1, wish I could be of more assistance
scoot05redss said:
Sorry, I haven't flashed any modems to my Note 10.1, wish I could be of more assistance
Click to expand...
Click to collapse
can u give any alternative way to solve the problem
like
can u upload the apk file of triangelaway that solved your problem
and can u mention what was your firmware version
thanx
Sorry buddy, I really can't. Since, my tablet had been damaged and I had flashed roms since. I can't remember what version I was using. Triangle away apk can be found from a Google search but I don't have the apk for the one I used. Sorry again! I know it's a PITA!
Hello mates!
I just had this problem some days ago, when i accidentaly dropped my sm p601. It was working fine so i wasnt worried at that time.
Next day it presented the exact symptoms that you guys described. The screen couldn't be turned on after being turned off, brightness controls not working.
I realized it could be a hardware problem because of the drop that the device suffered, then i stumbled in this topic where our friend scoot05redss mentioned:
I've read online, that there maybe a loose ribbon cable
Click to expand...
Click to collapse
Well, since i live in Brazil and we have little to none authorized customer service support from Samsung, i decided to open the device.
(I searched for a disassembly video in youtube. There are one or two avaliable)
It happens that the mentioned LCD ribbon cable is the first thing to pop up when you open the device, so i decided to give it a try, and guess what, it worked.
I just opened the device, lifted the cable lock (that black plastic thing that sits upon the cable) and i gently moved the cable inside the conector (I didn't even had to remove it).
Closed, turned on, everything working as before.
Ps.: Its kinda hard to open the device without the appropriate tool shown in the video, but i managed to open it with a knife, taking maximum care not to leave marks in the screen (the silver frame however couldnt be spared from some scratches.
Thanks for the help!
I can confirm that disconnecting the LCD ribbon cable while the unit is on, reconnecting it, and then rebooting the device fixed the issue for me. My wife accidentally knocked it off her nightstand and while using it during the middle of the next day the screen suddenly faded to black. After noticing that the screen was still on but the back light wasn't working, I popped it open and tried disconnecting the battery but didn't try the LCD ribbon, didn't think that'd make a difference. But I'm glad that's all it was!
Ive got this issue on a grand prime sm-g361h as soon as i lock the screen or it times out thats it, doesn't turn back on until i hard reboot it. super frustrating.. going to try flash a modem to see if it fixes
fredquintao said:
Hello mates!
I just had this problem some days ago, when i accidentaly dropped my sm p601. It was working fine so i wasnt worried at that time.
Next day it presented the exact symptoms that you guys described. The screen couldn't be turned on after being turned off, brightness controls not working.
I realized it could be a hardware problem because of the drop that the device suffered, then i stumbled in this topic where our friend scoot05redss mentioned:
Well, since i live in Brazil and we have little to none authorized customer service support from Samsung, i decided to open the device.
(I searched for a disassembly video in youtube. There are one or two avaliable)
It happens that the mentioned LCD ribbon cable is the first thing to pop up when you open the device, so i decided to give it a try, and guess what, it worked.
I just opened the device, lifted the cable lock (that black plastic thing that sits upon the cable) and i gently moved the cable inside the conector (I didn't even had to remove it).
Closed, turned on, everything working as before.
Ps.: Its kinda hard to open the device without the appropriate tool shown in the video, but i managed to open it with a knife, taking maximum care not to leave marks in the screen (the silver frame however couldnt be spared from some scratches.
Thanks for the help!
Click to expand...
Click to collapse
I had the same problem and fixed it in the same way.
n3xus5 said:
Ive got this issue on a grand prime sm-g361h as soon as i lock the screen or it times out thats it, doesn't turn back on until i hard reboot it. super frustrating.. going to try flash a modem to see if it fixes
Click to expand...
Click to collapse
Ok Issue Was MODEM i dd modem.img to modem partition from another phone exact same that working and its now 100% up n running only issue now is i have duplicate IMIE numbers
Color issue after screen off
My Note 10.1 2014 (P605) is ruining smoothly for 3.5+ years without much trouble. Now, it's screen is giving some color issue. Tab boots fine and colours shown correctly. Once screen is off, it start to invert (not sure whether the correct word) colours. Later I observed screen not switching on but accepting touch commands.
I tried color invert setting, it seems not effective. Flex cable was not loose but sometimes reconnecting resolved temporally. Re-flashed the OS but issue came up after few days. This may seems like screen fault, but screen working fine at boot till screen off.
Does anyone have similar experience or advice to help me out.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Important Experience !!!
scoot05redss said:
Ok guys, so I'm having an issue with my Note 10.1 2014 Edition. Whenever the screen times out, or you lock it, the screen will not come back on. The buttons will light up, but the screen is unresponsive. Hold the power button for a reboot and it reboots, screen works fine until the next lock. So obviously first thing, wiped everything, and reloaded Hypderdrive, only to get the same issue. So I go in again to recovery, and while I'm doing some research, TWRP times out and the screen goes black, and again, I'm unable to "wake" the device. Now I'm thinking hardware, but the power button is being recognized to lock it, so it should be recognized to unlock it as well and it is because the button lights come on. I've gone in, did a complete wipe including /system and /data and I'm currently trying to load a new rom to my microsd card to load, but the screen timed out again and I have to reboot the device back into recovery each time to get the screen to work. I'm pretty sure the root method I used, voided my warranty, so sending it in is probably not an option. When I reboot into download to check the status, It just says Downloading... Do not turn off target!! and I see no information in the top left of the screen. Anyone have any idea as to what could be causing the screen to do this? I'm kinda lost at this point! Thanks in advance.
P.S. So I was able to get into Download, and found my Current Binary is Custom, my System Status is Custom, and my Warranty Bit is 1, so I'd assume warranty is out of the option.
P.P.S I got a new rom loaded everything flashed fine, booted, let it set, when the screen timed out, again won't turn on. I can almost say 100% it's not a rom/Kernel issue. But beyond that I'm lost!
Click to expand...
Click to collapse
"Ok guys, so I'm having an issue with my Note 10.1 2014 Edition. Whenever the screen times out, or you lock it, the screen will not come back on. The buttons will light up, but the screen is unresponsive. Hold the power button for a reboot and it reboots, screen works fine until the next lock."
I was been displayed dark screen (Death screen) by shock on road. Because I put my tablet Samsung note 10.1 P601 (2014 edition) in basket of motorbike. These are solutions:
- Case 1:
If dark screen and the buttons are light up like this question then you need unplug only LCD cable inside tablet and plug again.
- Case 2:
If Death screen and it's no light then you need plug and replug power cable and LCD cable inside table.
" 2 these case you can search and see YouTube How to open and fix black screen Samsung note 10.1 2014"
udeshjr said:
My Note 10.1 2014 (P605) is ruining smoothly for 3.5+ years without much trouble. Now, it's screen is giving some color issue. Tab boots fine and colours shown correctly. Once screen is off, it start to invert (not sure whether the correct word) colours. Later I observed screen not switching on but accepting touch commands.
I tried color invert setting, it seems not effective. Flex cable was not loose but sometimes reconnecting resolved temporally. Re-flashed the OS but issue came up after few days. This may seems like screen fault, but screen working fine at boot till screen off.
Does anyone have similar experience or advice to help me out.
Click to expand...
Click to collapse
Living after few months with this problem I can conclude following.
1. It is very difficult to find a pattern for screen to go pink or black. However, I noticed that problem comes frequently when it was used by my baby.
2. Disconnecting and reconnecting LCD cable temporarily resolve problem every time. May be hoangctm is more accurate on procedure.
3. I use this tablet every day. 45min video, 2 x 15min streaming and 1 h reading. Steady use of tablet does not give problems.
4. It is possible to replace LCD flex cable without dismantling screen and this is my next step.
I was also experiencing this issue. What would happen is that my Samsung Galaxy Note 14.1 would work well after a reset but as soon as it locked you couldn't see the screen.
I tried the solution posted in this forum. I opened up the tablet and repositioned the LCD ribbon cable while the screen was active. The tablet is now working well. I can activate the tablet properly after the screen has locked. Thank you all.