Hello XDA Forum,
my daughter's tablet screen was cracked. A Chinese web shop offered replacement screen (lcd, digitizer & glass combo) and I ordered giving them correct model of the tablet. Now, I received physically perfectly fitting gear but I won't get any image on the screen. I can see backlight lit for a short while.
I swapped the faulty LCD/digitizer/glass back and could see picture just perfectly. So it seems like resolution issue. I even swapped the new LCD back while tablet was powered up (I know, I know..) and I could see picture in the replacement screen as well! But the image was distorted just like you've seen in CRTs when resolution/refresh don't match the screen capabilities.
Tablets model is Asus ZenPad 10 Z301M-1B006A. This site explains the differences pretty well:
w w w . p d e v i c e . c o m
/comparison/asus-zenpad-10-z301m-vs-asus-zenpad-10-z301mf
Even the GPU is same for 1920*1200 and 1280*800 system.
Actual replacement LCD is NV101WUM-N52 (1920*1200).
It perhaps should have been TV101WXM-NU1 (1280*800).
I saw some web shops giving possibility to select resolution but my Chinese web shop just asked the model. I have perfectly correct model in the order.
The sticker on the replacement panel says ATAB435 and "Asus Z301M Z301MFL" plus some Chinese chars. This suggests the LCD was indeed intended for Z301M/1280*800 tablet.
Now, the question is, could my replacement screen picture problem be due to wrong initial Android bootup resolution setting which I could possibly change with adb thus upgrade the tablet to 1920*1200 reso?
Hope this question made any sense at all.
BR,
Timo
karhulitos said:
Hello XDA Forum, my daughter's tablet screen was cracked..........
Click to expand...
Click to collapse
I don't have this device myself but, I did a little digging around...
First of all, I did see that the new display is actually compatible for your device.
If this were me, my next thought would be to go to the following manufacturers website FAQ section...
https://www.asus.com/us/Tablets/ASUS-ZenPad-10-Z301M/HelpDesk_Knowledge/
... and see if I can locate anything that's regarding the Display (ie... LCD, Digitizer, Display, etc...) to see if there was anything that may/might/does apply to your issue.
Personally stating, I can only assume that it may be tied to some type of Calibration or similar.
Just to clarify, if this were me, and nothing worked, I would just double check all the connections. Specifically for connections that may be loose, dirty, disconnected (by accident), etc... because things can happen when putting them together that was overseen/forgotten accidentally.
In addition, I would look at some YouTube videos in replacing the Digitizer Display for the same/similar device. I would do this only as a reference regarding what I did and see if I had overlooked anything.
If all is well and nothing was successful, I would personally feel that this Digitizer was simply defective. I would then look to begin the process of returning/replacing the Digitizer.
If I obtained the same Digitizer part, and the same happened, I would just look into return/exchange that one for the other part.
It's really hard to diagnose many items/issues without having the actual/same device.
I hope that this was helpful in some way and I had explained this okay via text.
I do wish you the best of luck!
~~~~~~~~~~~~~~~
Unless asked to do so, PLEASE don't PM me regarding support. Sent using The ClaRetoX Forum App on my Apple Macintosh.
Ibuprophen said:
First of all, I did see that the new display is actually compatible for your device.
Click to expand...
Click to collapse
First of all, your effort is highly appreciated. Thank you.
Very interesting. What made you think my replacement display combo (LCD: NV101WUM-N52) is compatible with Z301M? All hints I could gather was stating it's compatible for Z301MF* models.
I tried to look for this information but couldn't really find the proof.
Ibuprophen said:
Personally stating, I can only assume that it may be tied to some type of Calibration or similar.
Click to expand...
Click to collapse
This is my study hypothesis as well. First, I was thinking that my problem is just due to the LCD not understanding the signal sent to it by the GPU.
commands like:
Code:
adb shell
wm density DPI (Change display density)
wm size RES (Change display resolution)
might change the startup resolution so that the new LCD can show it and otherwise get initialized properly.
I was just puzzled that Google didn't give any hits of people doing this so I just couldn't believe I'm the 1st one to experience this. This is why decided to ask here.
What I do not know is can ARM or tablet hardware in general negotiate screen refresh/resolution/DPI information via the cable or is it always something which is hard coded in the firmware itself? After all a tablet isn't really a plug and play hot swap equipment, eh?
Only thing avoiding me to test above approach is that the web shop may want to replace my new LCD. Let's see how it boils. Is it broken or is it electrically unfit for the hw/sw model I have?
Ibuprophen said:
Just to clarify, if this were me, and nothing worked, I would just double check all the connections. Specifically for connections that may be loose, dirty, disconnected (by accident), etc... because things can happen when putting them together that was overseen/forgotten accidentally.
Click to expand...
Click to collapse
I hear you. I did this approximately 10 times. Some 5 times I switched back to the cracked 1280*800 and shows the picture fine. Back to NV101WUM-N52 and all I get get is backlight.
Ibuprophen said:
It's really hard to diagnose many items/issues without having the actual/same device.
Click to expand...
Click to collapse
Jep. I think I just need to send it back to China. But please come back to me and tell how did you come to conclusion the screen is fit for Z301M?
karhulitos said:
......... I think I just need to send it back to China. But please come back to me and tell how did you come to conclusion the screen is fit for Z301M?
Click to expand...
Click to collapse
I've seen that part number for your device within some other websites like Amazon, eBay and even Asus as a replacement part option.
I've seen this before. Sometimes a new device will have upgrade options when it's first launched.
I've got an Asus Transformer T100TA Tablet where this option was provided for the Digitizer, Memory and a few others.
As a matter of fact... I've got my Asus Tablet still apart with the newer Digitizer Display ready to be put back together. Unfortunately it's been ready to be assembled for approximately a year now (shame on me... LOL! ).
~~~~~~~~~~~~~~~
Unless asked to do so, PLEASE don't PM me regarding support. Sent using The ClaRetoX1 Forum App on my Apple Macintosh.
Ibuprophen said:
Unfortunately it's been ready to be assembled for approximately a year now (shame on me... LOL! ).
Click to expand...
Click to collapse
Pull yourself together and do it now! Thanks man for your insights.
BR,
Timo
karhulitos said:
Pull yourself together and do it now! .........
Click to expand...
Click to collapse
LMAO!!!
It's actually my first (and only) tablet I've ever owned. It's like a BIG Android... LOL!
I've got a good handful of various Android devices, 3 Laptops and 2 PC Towers (with 3 monitors). This list only includes what's actually working (also less the various parts as well). On top of the various projects I'm involved in bouncing from one to another as well as Life itself.
You can see why reassembling the tablet is actually something I want/need to do, it's just not very high on my priority list at this point in time.
I wish you the best of luck!
~~~~~~~~~~~~~~~
Unless asked to do so, PLEASE don't PM me regarding support. Sent using The ClaRetoX1 Forum App on my Apple Macintosh.
Ibuprophen said:
LMAO!!!
I wish you the best of luck!
Click to expand...
Click to collapse
Thank you.
One last detail for the record should someone else sometime stumble upon this problem.
Z301M original LCD is KD101N59-42NA-A8 which was later replaced, according to test report 081-170425-200, by TV101WXM-NU1 1280*800.
So be careful when ordering replacement screen for Asus ZenPad 10. There is also some green & yellow connector difference which wasn't involved in this case but I just wanted to mention it here.
Related
Hi,
On Ebay I have bought a XDA 2 PCB board. What I need help with is what other parts will I need to make work. So far I think I need:
1 DIY battery kit
1 Touchscreen LCD
1 Sync cable (which is best?)
some software for my PC, any ideas?
1 case, any ideas were I can get this from or has any one got one?
Any ideas on get this project up and running would be most appriecated.
Thanks
Cmcmill01
Software on the pc is no problem.
You just need Active Sync, can be downloaded from here http://www.microsoft.com/windowsmobile/resources/downloads/pocketpc/activesync37.mspx
With the rest, I can't help you...
Cheers Jos,
Anyboby else with some ideas?
Has anybody got a faulty XDAII, wishing to sell?
Cheers
Cmcmill01
well i think that most peoples warrenty would replace their defect xda2 still
unless they abused it in a manner most faul that the company would notice
but with time and newer radio stacks and a full rom kitchen
you will mostlikely be able to get some
though as to buying the parts from new maybe diff to find and prob pricy aswell
Cheers for the Info
Has the XDA II got the same case as any other handheld?
As for the screen does that come in two parts?
cheers
Has the XDA II got the same case as any other handheld?
Click to expand...
Click to collapse
i dont think i ever seen to pda's using 100% the same case
As for the screen does that come in two parts?
Click to expand...
Click to collapse
all pda's i've ever messed with have seperate lcd and touch screen
Is there any way to test that board before you spend so much money, because the xda2 is so new I dont see you getting secondhand parts and to buy them new is likely to cost somewhere near the price of buying a warranted unit.
So here are my thoughts, if they are complete crap let me know. :lol:
Get the board, attach the power and sync lead (can it run with out battery attached just on the mains?)
Get the LCD screen (ACX706AKM sony part, XDA I, is it the same screen for the XDA II)
Load up the ROM and Radio Stack, is this all I have to do to get Windows 2003 on the XDA?
Then get a case, by that time I'll probably have spent more than a new one.
Don't think you can use a XDA I screen, because it has less colors (4K instead of 64K).
Jos said:
Don't think you can use a XDA I screen, because it has less colors (4K instead of 64K).
Click to expand...
Click to collapse
Does anyone know the Part number for the XDA II screen, I'll try and source one that way?
screens
Are any Ipaq screens used on the XDAII?
cheers
i think there is an url somewhere for people who want to buy a new tft and touchscreen i'll look for it if you like
That would be great if you could.
Thanks
http://www.pdasmart.com/pdaphone.htm
here you go
Cheers, for that.
But is that not for the XDA? not the XDAII, they have different screens!
Good luck finding a screen. I have called Sony trying to get one for XDA, and they referred me to the MFG who does not respond to any consumer inquiries. It seems that they don't want end users to have the ability to repair their own phones. If you find a source for the screen I'd love to know.
Good luck!
Hi CMCMILL01
Try http://www.pdatechcenter.nl/reparatie_xda.html
They are good!
Kees
Does anyone know where I could find a pin configuration chart for the display cable inside the uni?
I know its adventurous but I wouldnt mind making a monitor out!
joey7415963 said:
Does anyone know where I could find a pin configuration chart for the display cable inside the uni?
I know its adventurous but I wouldnt mind making a monitor out!
Click to expand...
Click to collapse
Yes, i'm also things about that, but now don't have too much free time to play with it
Come on people does anyone know?
Or is this gonna be a long week with the multimeter and a few books!
SD to VGA adapter maybe??
I saw in one of the Windows mobile magazines that they make SD to VGA adapters. It mentioned that there was a microSD version soon to be released, and that there was a bluetooth product as well.
AllanonMage said:
I saw in one of the Windows mobile magazines that they make SD to VGA adapters. It mentioned that there was a microSD version soon to be released, and that there was a bluetooth product as well.
Click to expand...
Click to collapse
If memory serves me correctly the Universal was original sold with an optional TV/VGA out cable. It may be worth posting on the HTC forum itself or digging around. I am pretty sure that it was only the first few G3 devices that were advertised as having these cables, but have had a dig around myself last year for these to no avail.
beast0898 said:
If memory serves me correctly the Universal was original sold with an optional TV/VGA out cable. It may be worth posting on the HTC forum itself or digging around. I am pretty sure that it was only the first few G3 devices that were advertised as having these cables, but have had a dig around myself last year for these to no avail.
Click to expand...
Click to collapse
Interest information, do you know more details about that
Wow, that sounds kewl, might have to email HTC.
The only info I could find on this is whats in the Wiki anyways
The touch-screen controller given shows the pin-outs which should tell us the touch-screen pin-config'.
I've given up on this anyway so I turned my camera into a nightvision camera really easy to do!
joey7415963 said:
Wow, that sounds kewl, might have to email HTC.
The only info I could find on this is whats in the Wiki anyways
The touch-screen controller given shows the pin-outs which should tell us the touch-screen pin-config'.
I've given up on this anyway so I turned my camera into a nightvision camera really easy to do!
Click to expand...
Click to collapse
Share more details, I too was playing before with camera and IR leds
sorry this will be mega rushed just realised im still in my pjs and gotta be at work soon!
Basically you dissasemble to PDA as shown in the wiki, then take apart camera base, behind it there should be a coloured filter (IR filter) take it out and replace with two really dark things (like the begining of a negative) then put together and take pictures in the dark whilst pushing a button on a remote control i will make a proper how to do thingy when im home tonight!
Bye for now!
IR Camera
Right first of all I think I tried it with my Uni and couldn't suss how to get to the IR filter but I tried it on my Nokia and its working like a charm!
1: Take apart the phone,
2: Uncouple camera,
3: Using a knife prise the four corners of the circuit board off the base of the camera (make sure you only go about 1mm in MAX! Also make sure you remember which way round it goes ),
4: Unscrew the lenses off the front,
5: Punch out the IR filter, this should be the slightly coloured one usually red (or find a way to take it out properly if you wanna keep it but mine was glued on),
6: Find an old photo album and take the negatives, look for the first part where it is just pure black (no pictures) and cut two circles out of it to place where the IR filter was, (this will be your visable light filter),
7: Reassemble,
8: Go somewhere dark and use a remote control as a light source and take photos!
beast0898 said:
If memory serves me correctly the Universal was original sold with an optional TV/VGA out cable. It may be worth posting on the HTC forum itself or digging around. I am pretty sure that it was only the first few G3 devices that were advertised as having these cables, but have had a dig around myself last year for these to no avail.
Click to expand...
Click to collapse
yea i read it too...oh wait i think i remember where i read it....in the development n hacking section....they talked bout it...i think u can still buy those optional TV/VGA but the only problem is that u cant use the sd therefore u have to use the main memory which is not enough...
Tahmaseeb said:
yea i read it too...oh wait i think i remember where i read it....in the development n hacking section....they talked bout it...i think u can still buy those optional TV/VGA but the only problem is that u cant use the sd therefore u have to use the main memory which is not enough...
Click to expand...
Click to collapse
Hmmm.... sounds interesting, I rekon it's gotta be expensive Oh well
thanks to everyone who has tried to help me I hope I've paid back with the
IR camera trick lol!
Hey guys. I have gotten alot from this website so I would like to give back. I own and operate a mobile phone repair shop and would like to extend my services to this forum. Most of you seem pretty techical so even if you just want the part (microphone, ear speaker, Loud speaker, LCD) I will provide it for you at a low cost plus shipping of course. I mostly deal with hardware issues so please don't PM me or post asking about software, I am a total noob when it comes to that!
Thanks again to all the rom builders and contributers who have helped make my phone awsome!
If you can source the vibrate motor for an HTC S710 I would be forever grateful. Where abouts are you located?
EDIT: I see you're in Phoenix.
Most of the parts I carry are for US released HTC phones but often they carry simular parts. If you can post a picture of what it looks like I'll see if I have a match.
I will upload a picture in a little bit, however here are the specifications from the HTC Vox Service Manual for the motor;
JT0406-30CSR1, JNTECH, Cylindrical, 3V, 100mA, 12000+/-3000 rpm, 60/-, 20degC, 11.2*5.1*5.8mm
The cylinder has J7D05 printed on it and has 2 prongs that make contact to the pad on the PCB. I've tried many different other motors but none of them physically fit in the spot. So if you have any motor rated to those specs and is smaller or equal to the dimensions above, I will take it.
Here are two pictures of it. They are quite large, so not inlined. Not my camera, one of those funky digital ones that I have no idea how to adjust the focus on.
http://i25.tinypic.com/20psxg3.jpg
http://i25.tinypic.com/22dcb4.jpg
I'll check my inventory tomorrow. The shop is closed for today, it being the 4th of July and all.
Ah yes. Thanks, I shall await your response in great excitement.
Happy Indie Day!
A friend of mine has an O2 XDA Orbit but the usb works for charging but not for the data link.
Is this fixable? and if so, do you perform the fixes !!!!
@pna
I had the same problem with my Dash/Excalibur. I had to turn off the USB charging feature in the settings and then the data worked fine. I just either turn it back on if I need to charge via USB on my PC and don't have a wall charger handy. Tell your friend to try that.
Edit:
Also Turn off Advanced Network Functionality to along with charging over USB.
pna said:
A friend of mine has an O2 XDA Orbit but the usb works for charging but not for the data link.
Is this fixable? and if so, do you perform the fixes !!!!
Click to expand...
Click to collapse
If the pins in the socket look straight re-flow the solder on the mainboard or get someone to do it. It's fairly easy. New sockets are about $4 on fleabay but as there are multiple lines close together you do need skill to replace.
M.S
@h4waii
Sorry friend. I don't have one that looks like that by HTC. However the T-Mobile Sidekick 3 vibrator does look like it. If I had it here to test I would be able to look closer. Once again, sorry friend.
Planetneo said:
@h4waii
Sorry friend. I don't have one that looks like that by HTC. However the T-Mobile Sidekick 3 vibrator does look like it. If I had it here to test I would be able to look closer. Once again, sorry friend.
Click to expand...
Click to collapse
I do, however, stock them. pm me and I'll list it on eBay.I'm in the UK though so shipping will be dependant on where you are. Outside UK is £7.
M.S
Good, this is the point right? To help our fellow members. Thanks Mysterious Stranger.
Planetneo said:
Good, this is the point right? To help our fellow members. Thanks Mysterious Stranger.
Click to expand...
Click to collapse
Help if asked, yes. Spam to get sales, NO.
M.S
Anyway you can check out my thread here...http://forum.xda-developers.com/showthread.php?t=405758
Might find it intresting.
htc touch cruise
One of the give aways in buying this product is CoPilot Live 7 with free city map. I choose Muscat in Oman in English but I can not activate it. I went to the dealer but he wants me to pay to activate it.
Planetneo said:
Hey guys. I have gotten alot from this website so I would like to give back. I own and operate a mobile phone repair shop and would like to extend my services to this forum. Most of you seem pretty techical so even if you just want the part (microphone, ear speaker, Loud speaker, LCD) I will provide it for you at a low cost plus shipping of course. I mostly deal with hardware issues so please don't PM me or post asking about software, I am a total noob when it comes to that!
Thanks again to all the rom builders and contributers who have helped make my phone awsome!
Click to expand...
Click to collapse
Right on! I have been wanting to replace the metal bezel that goes around the front of the AT&T 8525 (U.S. HTC Hemes). Mine has gotten quite scratched and scuffed over the last year, and I would love to have it returned to it's original clean, shiny look.
Do you happen to carry this part by any chance? Or know of an affordable place to obtain one?
I get mine from a guy on ebay. I used my last 3 over the holiday weekend so I am out till I order some more on Monday. They are about $28 shipped. Link below....
http://cgi.ebay.com/HTC-Hermes-Cing...ryZ20336QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
Planetneo said:
I get mine from a guy on ebay. I used my last 3 over the holiday weekend so I am out till I order some more on Monday. They are about $28 shipped. Link below....
http://cgi.ebay.com/HTC-Hermes-Cing...ryZ20336QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
Click to expand...
Click to collapse
If you need the full housing email Amit / Raki Computers and ask - they have them as well at not much more $ ( about $26 IIRC) if you ask although the parts they sell are used / stripped from BER phones so some have minor marks and it's pot luck.
M.S
edit - I emailed Amit @ Raki myself anyway and he's listed the full housings here: http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=220254094906
better value IMO.
Yes. We've got software support and now hardware support. This thread needs to be stickied.
Hi to all, today besides it looks like Friday 13th. (my car broke down) I took after I dropped my HTC One X my phone from the service with a new display.
After 2 hours I have been called and saw that the display again is broken from the left side, near the usb towards the top, (power button) is a line and cracked.
I really don't know and paid much money today and to pay again?
Could this happen or should I blame myself?
I always take good care of the phone and always carry it in my side pocket which is wide enough...
Can anyone advice me what to do?
If you are 100% positive that the screen was intact when you got it out from the service, you should take it back and council with the person who serviced the phone. It there are no signs of physical abuse or anything, you should have some kind of warranty on the display or at least on the changing service.
Dirrtydog said:
If you are 100% positive that the screen was intact when you got it out from the service, you should take it back and council with the person who serviced the phone. It there are no signs of physical abuse or anything, you should have some kind of warranty on the display or at least on the changing service.
Click to expand...
Click to collapse
thank u for the reply..the service will not give me a new one..but is the display so sensitive? i mean could it break by wrong installation?
Are you sure it was completely perfect at the service center? Did you inspect your phone whatever the screen was replaced correctly or there were any cracks from the beginning?
There's not much you can do over here... You can tell them what happened and ask for replacement but I'm not sure they will replace it for free...
vin4yak said:
Are you sure it was completely perfect at the service center? Did you inspect your phone whatever the screen was replaced correctly or there were any cracks from the beginning?
There's not much you can do over here... You can tell them what happened and ask for replacement but I'm not sure they will replace it for free...
Click to expand...
Click to collapse
as far as i could see the screen was ok...im not an expert in replacing but could it be by placing the screen wrong it could crack?
Okidoki as far as i did not get the right answer to this burning question of mine another..whats the difference between the original screen and a clone? I see lots of advertising on ebay claiming its a original HTC One X screen..
How to recognise this?
If I order a new display by my self..in what kind of price tag should i look at?
Anyone?
Unetwork said:
Okidoki as far as i did not get the right answer to this burning question of mine another..whats the difference between the original screen and a clone? I see lots of advertising on ebay claiming its a original HTC One X screen..
How to recognise this?
If I order a new display by my self..in what kind of price tag should i look at?
Anyone?
Click to expand...
Click to collapse
nobody?..............
No answer in 5 hours doesn't mean nobody will come along to answer at all, xda is not a helpdesk company. Timing has to be right and im sure you get your answer !
wauw thanks, great reply..
thought there might be some experts trying to help many after me about the display question...ok no one came along...so it means we are having a forum for software only and not about, it might come handy for many others, hardware....
Forget it sorry for even opening this topic...
Bedankt geweldig!
en volgende keer eens kijken waneer dit topic geopend werd..not 5 hours...
Unetwork said:
wauw thanks, great reply..
thought there might be some experts trying to help many after me about the display question...ok no one came along...so it means we are having a forum for software only and not about, it might come handy for many others, hardware....
Forget it sorry for even opening this topic...
Bedankt geweldig!
en volgende keer eens kijken waneer dit topic geopend werd..not 5 hours...
Click to expand...
Click to collapse
I feel some sarcasm here, and i don't see why ? It is how it is, when somebody with hardware knowledge is passing by this thread and he has the time he will answer. Only thing im pointing out that xda is a free site and people answer when they want.
You could at least thank me for bumping this thread back on top of the list. Enlarges the chance of being looked at
Sommige mensen.......
Good luck in finding the answers you need.
Try rounded.com it has original parts though I think the prices are a little high.
Sent from my HTC One X using Tapatalk 4 Beta
athulele said:
Try rounded.com it has original parts though I think the prices are a little high.
Sent from my HTC One X using Tapatalk 4 Beta
Click to expand...
Click to collapse
Thank you!! Great and I ordered a new display there and the price is much cheaper than the price offered here in Skopje, Macedonia.
But still 1 question how to recognize a clone from an original screen?
What I noticed is that the screen replaced on my phone is slight smaller as at the bottom part I can see the led light trough the house shining.
Also the left < is not shining while the home and > button is lighting.
The time before (when it has been replaced also) I had the same problem. At daytime its hard to notice but at night its very clear that only 2 buttons are lighting up.
Hahahahaha epic fail.......cough goo cough gle is cough your best friend.
here you can see my broken screen and the navigation button which is not lighting up
That has been the same case with the other replacement.
Also the crack is at the same position as the last one
I paid 100 euro for this one.
Mr Hofs said:
Hahahahaha epic fail.......cough goo cough gle is cough your best friend.
Click to expand...
Click to collapse
LOL :good:
Ok here my last try as in the 3 days I did not get any answer, it might be that this issue is unknown?
Anyway one more try..
My HTC One X broke now a couple of times and the last time it broke at the same space as before, again I did not drop it
At the bottom I can clearly see a small open space and the 3 navigation led light shining although the navigation arrow on the left (see attached picture) is not lighting up and at night it can't be seen.
The main reason for this topic to get more informed and to put a claim at the mobile phone service and to get my money back.
Also looking at Ebay for a screen replacement it looks like a jungle as all are claiming to sale original displays but again prices are from 45 - 150 euro's. Is there some way to recognize a none (clone) original screen from a original?
Again sorry for this chain of mine on this topic but i just wonder why twice my display cracked at the same place.
It's just a coincidence that the screen broke at exactly the same point...
By looking at what you've said... I think the screen might not have fitted correctly... Hence causing the led not to shine as brightly as it should... May be there is some gap left...
About the screen originality... It's really hard to determine... If you could send us the link of the part which you are buying.. Then someone might be able to judge it's authenticity..
-Sent from my IceCold One X!
vin4yak said:
It's just a coincidence that the screen broke at exactly the same point...
By looking at what you've said... I think the screen might not have fitted correctly... Hence causing the led not to shine as brightly as it should... May be there is some gap left...
About the screen originality... It's really hard to determine... If you could send us the link of the part which you are buying.. Then someone might be able to judge it's authenticity..
-Sent from my IceCold One X!
Click to expand...
Click to collapse
Thank you very much your answer
I also think it was not placed on the correct way and than the issue of the left navigation without lighting up as it should.
And the cap.
I wrote to rounded.com but no reply from them.
Maybe if someone could take a look at Ebay in Europe and to advise me which one to buy?
Should I buy the whole thing again complete or just the glass?
Also can be in a PM here.
Again thanks for the help :good: :good: :good:
They say its easier to replace the touchpanel and the digitizer in one.....many people had trouble to disassemble the 2 components from each other !
Mr Hofs said:
They say its easier to replace the touchpanel and the digitizer in one.....many people had trouble to disassemble the 2 components from each other !
Click to expand...
Click to collapse
Thanks, any place you can advise?
Listen, stop complaining that people aren't answering your questions. As Mr.Hoff has repeatedly tried to tell you, people have NO OBLIGATION to answer you, nor does it mean that because they're on XDA They know the answer to your questions. XDA is a priviledge, without XDA you probably wouldn't have a place to even ask your question.
NOW TO ANSWER YOUR QUESTION.
The difference between HTC Screen and a Generic Replacement screen is alot.
HTC Screen = LCD2 which is basically HD screen
Generic = LCD Screen with a much lesser resolution.
Also the part numbers are different, the only REAL way to tell whether you have the LCD2 screen or not.
However I cannot tell you the exact part number for a OEM HTC LCD2 Display.
Now stop ranting.
Hey guys.I'm new here and I'm a HTC10 user for the first time.Before this phone I used LG Nexus4 and P970.
I'm loving this device so far.The device is with me for 7-8 months.But last month it snowed here in Turkey and I was on my way to basketball match at night in the Arena.I saw this issue for first time at that night.Thought it's about cold weather(because it's metal body?).BTW I've got a Spigen's 2 pieced case.
Also this device has been already RMAd once because of screen popped out(glue was not strong enough I guess).
But this month I'm seeing it almost everyday.When I touch screen with a little pressure it's going away for a second and comes back or not(it's just random sometimes).Sometimes I can't even take photo because of randomness of this issue.Also there's a little white dot in the bottom right corner of screen.It appears at white backgrounds and it's brighter than other areas.This is also an issue for me.
Tomorrow I'll RMA my phone to local service in here.
Just wanted to let you guys now about this and ask what it is all about?
It was my first subject in the forums.So sorry if I'm on the wrong place and sorry about my english.It's just not that good
Here's the album for images.I can't add images to forum yet.Please put "." instead of "*"
---imgur*com/a/9qVSe---
It has a lot of display problem. HTC 10 is flawed
Today I got the call from repair service.They said my device is repaired.Here's what's changed:
-Motherboard(New IMEI)
-Cpu (Dunno why)
-Lcd screen (From Sharp to Tianma)
Everything is perfect for now.Happy to get back on my musics with this phone and Hd598Cs. :highfive:
There's one thing I noticed because I used both LCD screens from Sharp and Tianma.
Sharp had a shadows(kinda look like it) on the side of panel.And Tianma has a yellow tint at bottom side of screen.Some guys said that It's glue and will go in time
burakksglu said:
Hey guys.I'm new here and I'm a HTC10 user for the first time.Before this phone I used LG Nexus4 and P970.
I'm loving this device so far.The device is with me for 7-8 months.But last month it snowed here in Turkey and I was on my way to basketball match at night in the Arena.I saw this issue for first time at that night.Thought it's about cold weather(because it's metal body?).BTW I've got a Spigen's 2 pieced case.
Also this device has been already RMAd once because of screen popped out(glue was not strong enough I guess).
But this month I'm seeing it almost everyday.When I touch screen with a little pressure it's going away for a second and comes back or not(it's just random sometimes).Sometimes I can't even take photo because of randomness of this issue.Also there's a little white dot in the bottom right corner of screen.It appears at white backgrounds and it's brighter than other areas.This is also an issue for me.
Tomorrow I'll RMA my phone to local service in here.
Just wanted to let you guys now about this and ask what it is all about?
It was my first subject in the forums.So sorry if I'm on the wrong place and sorry about my english.It's just not that good
Here's the album for images.I can't add images to forum yet.Please put "." instead of "*"
---imgur*com/a/9qVSe---
Click to expand...
Click to collapse
Sounds like they've repaired it rather than swap it out. A like for like would have been the best outcome for yourself.
dladz said:
Sounds like they've repaired it rather than swap it out. A like for like would have been the best outcome for yourself.
Click to expand...
Click to collapse
Yeah I'm happy with the way of solution.
Because someguy in here(Turkey),got a swap report and waited for a new device about 3 months.Because our services gather all devices in together once in month and at that time there was no swap unit for the guy.So he just waited,waited and waited...
But here's the thing,if you're going to change mobo,cpu and LCD;why don't you just swap? Only things that aren't repaired probably the camera,speakers,antennas etc.
burakksglu said:
Yeah I'm happy with the way of solution.
Because someguy in here(Turkey),got a swap report and waited for a new device about 3 months.Because our services gather all devices in together once in month and at that time there was no swap unit for the guy.So he just waited,waited and waited...
But here's the thing,if you're going to change mobo,cpu and LCD;why don't you just swap? Only things that aren't repaired probably the camera,speakers,antennas etc.
Click to expand...
Click to collapse
They look at the units creation date if it's BER then they'll swap it.
dladz said:
They look at the units creation date if it's BER then they'll swap it.
Click to expand...
Click to collapse
It's FA65 Series.So it's probably May production.
burakksglu said:
It's FA65 Series.So it's probably May production.
Click to expand...
Click to collapse
Released in April, I got mine on release day, could be a faulty batch. As you can't really communicate with htc directly (as in the tech who'll be looking at the phone) you have very little sway over what they do next.
It'd be interesting to see if they share notes with each other based on your case file, perhaps talking with them directly they can agree that a like for like replacement would be the most viable option moving forward. If not I'd say insurance would be the only other option, besides third party but at this point a patch up wouldn't fill me with confidence.
Sorry mate, not a lot more I can think of.
---------- Post added at 12:36 AM ---------- Previous post was at 12:36 AM ----------
burakksglu said:
It's FA65 Series.So it's probably May production.
Click to expand...
Click to collapse
Any idea how I could identify mine?
Nvm, mine is a sharp.
You can identify it with the Dev check app. Not sure if that's what you already used.
dladz said:
Released in April, I got mine on release day, could be a faulty batch. As you can't really communicate with htc directly (as in the tech who'll be looking at the phone) you have very little sway over what they do next.
It'd be interesting to see if they share notes with each other based on your case file, perhaps talking with them directly they can agree that a like for like replacement would be the most viable option moving forward. If not I'd say insurance would be the only other option, besides third party but at this point a patch up wouldn't fill me with confidence.
Sorry mate, not a lot more I can think of.
---------- Post added at 12:36 AM ---------- Previous post was at 12:36 AM ----------
Any idea how I could identify mine?
Nvm, mine is a sharp.
You can identify it with the Dev check app. Not sure if that's what you already used.
Click to expand...
Click to collapse
Yeah that's how I checked my screen.If you ask about serial number it was on the box or in the box.There was a sticker on my box when I bought.
And btw I got my phone back from repair last week.They repaired it quick,about 3 days.There's no problem but the yellow tint at bottom of screen.It's a common issue with Tianma,at least people say so.
burakksglu said:
Yeah that's how I checked my screen.If you ask about serial number it was on the box or in the box.There was a sticker on my box when I bought.
And btw I got my phone back from repair last week.They repaired it quick,about 3 days.There's no problem but the yellow tint at bottom of screen.It's a common issue with Tianma,at least people say so.
Click to expand...
Click to collapse
This the third? And theres a yellow tint? Sweet jesus you've not had much luck have you?
Sorry mate, but if that were me i'd be sending it back and asking for a new one, I'd cause hell over the phone with them. I'd make sure that the repair guys who are physically going to touch my device got the memo.
Really bad.
dladz said:
This the third? And theres a yellow tint? Sweet jesus you've not had much luck have you?
Sorry mate, but if that were me i'd be sending it back and asking for a new one, I'd cause hell over the phone with them. I'd make sure that the repair guys who are physically going to touch my device got the memo.
Really bad.
Click to expand...
Click to collapse
Well there's difference between UK Customer Services or HTC UK and HTC Turkey.For example: HTC Turkey says "You can replace it or get a reserve phone while yours is getting repaired,bla bla. But services say they'll give it to you if yours is not repaired after 10 work-days.Also HTC Turkey is not good at marketing,production or customer services.Some guys waited 3-6 months for replacement unit.
I'm using the same device but first time screen popped out from bottom left and changed.Also back button light was very dim than the other one.Then there was this screen problems at imgur album appeared,showed line like artifacts and white dot at bottom right(That's white dot is also common in a lot of users).Screen,mobo and CPU changed but still with the same metal body(I know it because there's a tiny dent at the body).
burakksglu said:
Well there's difference between UK Customer Services or HTC UK and HTC Turkey.For example: HTC Turkey says "You can replace it or get a reserve phone while yours is getting repaired,bla bla. But services say they'll give it to you if yours is not repaired after 10 work-days.Also HTC Turkey is not good at marketing,production or customer services.Some guys waited 3-6 months for replacement unit.
I'm using the same device but first time screen popped out from bottom left and changed.Also back button light was very dim than the other one.Then there was this screen problems at imgur album appeared,showed line like artifacts and white dot at bottom right(That's white dot is also common in a lot of users).Screen,mobo and CPU changed but still with the same metal body(I know it because there's a tiny dent at the body).
Click to expand...
Click to collapse
Appreciate different regions may have different levels of customer service, even though I strongly disagree with this.
Perhaps a complain to htc global? Explaining your predicament?
I'm not sure mate,