Hi and thanks for helping me,
I installed Verizon rom on my device, after that it's stuck in the welcome screen
Please wait, this may take a few minutes
I locked the bootloader, I thought it will help, but still stuck
now I can't unlock bootloader and I can't enter to Android OS
please help me how can fix this issue
thanks a lot
here is video
this is stuck over 30 min
http://ahmn.co/Upload/IMG_0161.MOV
I did reset factory from the recovery, I removed sim card, insert sim card, reboot, shutdown, safe mode, nothing changed
I can't flash new firmware because the device is: flashing_locked
I need help please
Codename for Verizon was XT1789-01. You need to give correct information.
mr_5kool said:
Codename for Verizon was XT1789-01. You need to give correct information.
Click to expand...
Click to collapse
My Phone Hardware is XT1789-05 and I loaded XT1789-01 Software, because that I have problem
If tell me how can skip android initial setup in Android 8 Wizard, problem will solve
It's weird.
AHMN48 said:
My Phone Hardware is XT1789-05 and I loaded XT1789-01 Software, because that I have problem
If tell me how can skip android initial setup in Android 8 Wizard, problem will solve
Click to expand...
Click to collapse
https://youtu.be/CxM5IP6bsgQ
sd_shadow said:
https://youtu.be/CxM5IP6bsgQ
Click to expand...
Click to collapse
Dear it's not about FPR, check the video again
I stuck at first page, I can't go further
http://ahmn.co/Upload/IMG_0161.MOV
AHMN48 said:
Dear it's not about FPR, check the video again
I stuck at first page, I can't go further
http://ahmn.co/Upload/IMG_0161.MOV
Click to expand...
Click to collapse
From what I can tell the XT1789-05 is a dual-sim and the XT1789-01 is a single-sim device.
I suspect that is the problem, or it just didn't flash correctly.
Either way locking the bootloader should only be done if firmware is stock unrooted and working correctly.
My only suggestion is trying the rescue option in.
MOTO Smart Assistant
Update your Moto with (Lenovo) MOTO Smart Assistant (PC)
Sent from my Rockchip RK3288 Chromebook using XDA Labs
sd_shadow said:
From what I can tell the XT1789-05 is a dual-sim and the XT1789-01 is a single-sim device.
I suspect that is the problem, or it just didn't flash correctly.
Either way locking the bootloader should only be done if firmware is stock unrooted and working correctly.
My only suggestion is trying the rescue option in.
MOTO Smart Assistant
Update your Moto with (Lenovo) MOTO Smart Assistant (PC)
Sent from my Rockchip RK3288 Chromebook using XDA Labs
Click to expand...
Click to collapse
I already tested with Lenovo Assist, it's didn't work as well!!!!
I stuck in the hell with no way out
AHMN48 said:
I already tested with Lenovo Assist, it's didn't work as well!!!!
I stuck in the hell with no way out
Click to expand...
Click to collapse
You can try using an USB C to LAN Adapter to connect to the internet.
Xargon1989 said:
You can try using an USB C to LAN Adapter to connect to the internet.
Click to expand...
Click to collapse
your idea is so good, I tried with Belkin USB-C to Ethernet and it doesn't work, I returned and Now I want to buy UNI based on their website will work with Android
also, what do you think about Wifi Wsky It's compatible with Android 8 too, because I find QR setup and it need to Wifi, right now can't find any Wifi but with this device will find Wifi, right?
thanks a lot
Xargon1989 said:
You can try using an USB C to LAN Adapter to connect to the internet.
Click to expand...
Click to collapse
I bought Uni USB-C to Ethernet Adaptor, Belkin USB-C to Ethernet Adaptor, there is a connection between phone and Modem, the Green and Orange Light will work fine, but no internet!!!!
I bought Wifi Adaptor as well, it doesn't work either!!!!
Now, recently Android 9 came for Verizon, there is any way to update my current Android 8 to Android 9 via ADB Sideload (Recovery Mode) or Update from SD Card???
Or someone please help me or guide me, basically my phone died and I can't do anything!!!!
:crying:
Related
Country: USA
Carrier: Sprint
Version: L520.08
Model Number: SPH-L520
Android Version: 4.2.2
Kernel: 3.4.0-1982676
Just wondering if the device already has a method for root or if one is currently in the making.
Tray app calleg Kingo Android Root. It should work.
mar10o said:
Tray app calleg Kingo Android Root. It should work.
Click to expand...
Click to collapse
Worked Great, Thanks Mate!
Now my next task finding a WiFi tether that works.
calvinweber said:
Now my next task finding a WiFi tether that works.
Click to expand...
Click to collapse
FYI, for anyone that is reading this i finally figured it out, the only app i could get to work is "WiFi Tether Router" in the Play Store
it does cost 1.49 however its better then 10 a month
Notes:
Go through all the settings and set them up for Method use "3 - HostApd"
Play Store: WiFi Tether Router
Not working for me!
calvinweber said:
Worked Great, Thanks Mate!
Now my next task finding a WiFi tether that works.
Click to expand...
Click to collapse
I've tried downloading and installing the drivers manually and nothing seems to allow the app to recognize the phone is connected, I tried 3 different PCs with the same result. I app loops between connect and disconnect your phone.
Here are the details:
Model number: SPH-L520
Android version: 4.2.2
Baseband version: L520VPUAMK2
Kernel version: 3.4.0-2054908
Build number: JDQ39.L520VPUAMK2
Any suggestions would be much appreciated.
Thanks!
Help Needed
Hey guys i just picked up my Sprint Samsung Galaxy S4 Mini Yesterday but i seem to have hard brick it i cant get to recovery just download screen. Does anyone have the Firmware or any files on how i can get back up and running? Any help would be greatly appreciated.
dominique.j.lopez said:
Hey guys i just picked up my Sprint Samsung Galaxy S4 Mini Yesterday but i seem to have hard brick it i cant get to recovery just download screen. Does anyone have the Firmware or any files on how i can get back up and running? Any help would be greatly appreciated.
Click to expand...
Click to collapse
If you can access download mode, it's nothing serious.
Head into http://sammobile.com or http://samsung-updates.com and look for your phone's model name. They have firmware for pretty much any device so hopefully they have some for yours.
So the only thing that freaks me out is all these region codes... I dont see one for USA...Now what lol
dominique.j.lopez said:
So the only thing that freaks me out is all these region codes... I dont see one for USA...Now what lol
Click to expand...
Click to collapse
Here's an Odin installable SPH-L520 official stock firmware : http://www.samsungis.com/Firmwares/596.html
droidfanluke said:
I've tried downloading and installing the drivers manually and nothing seems to allow the app to recognize the phone is connected, I tried 3 different PCs with the same result. I app loops between connect and disconnect your phone.
Here are the details:
Model number: SPH-L520
Android version: 4.2.2
Baseband version: L520VPUAMK2
Kernel version: 3.4.0-2054908
Build number: JDQ39.L520VPUAMK2
Any suggestions would be much appreciated.
Thanks!
Click to expand...
Click to collapse
I have the exact same phone and the exact same problem. Kies (via USB) recognizes there is a SPH-L520 connected but won't actually connect to it. I asked Samsung for the appropriate drivers (none are listed on the webpage for the device) but Samsung says there aren't any drivers for the SPH-L520. Kies does connect my SPH-L520 and my PC via WiFi, though. And, despite having enabled Developer Mode and USB Debugging, Kingo fails every time. Any ideas?
Try this: http://forum.xda-developers.com/showthread.php?t=2565758
It is also where Kingo originally got their method from, I wouldn't trust them too much if I were you. The best thing about the above method is, if it can't root the phone, it won't touch anything. If it can - it won't trigger the Knox. I tried on my JB 9190 and works. Unless you have a locked bootloader... that would complicate things.
hello guys is there a way to unlock samsung gs4 sprint to gsm been searching around cant find a good answer cos the phone seems to have a sim slot. also can it be flashed to cdma if the gsm potion wont work. thanks
foncall said:
I have the exact same phone and the exact same problem. Kies (via USB) recognizes there is a SPH-L520 connected but won't actually connect to it. I asked Samsung for the appropriate drivers (none are listed on the webpage for the device) but Samsung says there aren't any drivers for the SPH-L520. Kies does connect my SPH-L520 and my PC via WiFi, though. And, despite having enabled Developer Mode and USB Debugging, Kingo fails every time. Any ideas?
Click to expand...
Click to collapse
If you're on NA7 as a few of us seem to be, you're screwed I believe unless someone comes up with a recovery we can flash through odin or kies. I would like to be wrong about that, but I haven't found otherwise.
dbpaddler said:
If you're on NA7 as a few of us seem to be, you're screwed I believe unless someone comes up with a recovery we can flash through odin or kies. I would like to be wrong about that, but I haven't found otherwise.
Click to expand...
Click to collapse
NA7: what's that and how can I tell if I'm on it?
foncall said:
NA7: what's that and how can I tell if I'm on it?
Click to expand...
Click to collapse
That's your firmware version.
Go to Settings -> About Device. Last 3 characters of your version
foncall said:
NA7: what's that and how can I tell if I'm on it?
Click to expand...
Click to collapse
System Settings - > About device - > Software version.
L520VPUANA7
It's the version of software we're on. Still JB 4.2.2, but the last Ota under the guise of updating Spark also included Knox which is not allowing us to root through the Saferoot method.
Sent from my SPH-L720 using Tapatalk
dbpaddler said:
System Settings - > About device - > Software version.
It's the version of software we're on. Still JB 4.2.2, but the last Ota under the guise of updating Spark also included Knox which is not allowing us to root through the Saferoot method.
Click to expand...
Click to collapse
The stinkers! I thought I read that Sprint was coming out with an upgrade to JB4.3 for us S4 Mini users, but it hasn't been pushed to my phone yet like the WiFi calling upgrade was. Think that might alleviate the Knox-blocks problem if/when it occurs?
foncall said:
The stinkers! I thought I read that Sprint was coming out with an upgrade to JB4.3 for us S4 Mini users, but it hasn't been pushed to my phone yet like the WiFi calling upgrade was. Think that might alleviate the Knox-blocks problem if/when it occurs?
Click to expand...
Click to collapse
Why would that alleviate it? Knox is here to stay. Very doubtful any update is going to remove it. Lately it's all about locking things down.
Sent from my SPH-L720 using Tapatalk
Kingo Root App
mar10o said:
Tray app calleg Kingo Android Root. It should work.
Click to expand...
Click to collapse
Hi there, Kingo just fails over and over for my SPH-L520 Galaxy S4 Mini Any other suggestions? Thanks
Holhat said:
Hi there, Kingo just fails over and over for my SPH-L520 Galaxy S4 Mini Any other suggestions? Thanks
Click to expand...
Click to collapse
Go here. And you're welcome. Just thank the person that posted it.
hi guys, flashed the rom stock bumped v20i, I received an error in flash with wipe, I rebooted into recovery but does not go. i lost recovery and download mode (volume up and connected usb to pc does not turn on the device).
any solutions?
Same here, any on f460k korean version =/.
I am getting stuck oin bootloop so had to downgrade. Why can't you get to recovery with battery pull and volume down?
always boot certification security, on download mode and recovery =/ even when connect the usb cable.
http://www.usoftsmartphone.com/t269796.html
Can work?
danielg90 said:
hi guys, flashed the rom stock bumped v20i, I received an error in flash with wipe, I rebooted into recovery but does not go. i lost recovery and download mode (volume up and connected usb to pc does not turn on the device).
any solutions?
Click to expand...
Click to collapse
sambrooke said:
I am getting stuck oin bootloop so had to downgrade. Why can't you get to recovery with battery pull and volume down?
Click to expand...
Click to collapse
danielg90 said:
http://www.usoftsmartphone.com/t269796.html
Can work?
Click to expand...
Click to collapse
Can't get in fastboot mode =(.. i read this http://forum.xda-developers.com/lg-g3/general/fix-unbrick-lg-g3-stuck-qualcomm-hs-usb-t2933853 but cant find the COM port only the unknow device.
i folllowed http://forum.xda-developers.com/lg-g3/general/fix-unbrick-lg-g3-stuck-qualcomm-hs-usb-t2933853 and this is the result http://goo.gl/8FSTNp
i gonna try this http://forum.xda-developers.com/showthread.php?t=2582142 , if result i tell u, did u see the com port in your drive? i don't have drive for offline phone on f460 model.
Sorry this isn't helping you guys but..
I'm really afraid of this happening with my device. That's why I still love my Galaxy s4. Never heard of this on galaxy s4.
I really hope you guys figure out the problem. Good luck!
GG.... i got my phone bricked can't find a way to weak up it again :'(
mafury said:
i gonna try this http://forum.xda-developers.com/showthread.php?t=2582142 , if result i tell u, did u see the com port in your drive? i don't have drive for offline phone on f460 model.
Click to expand...
Click to collapse
Link for file g3?
Those files can be extracted from KDZ 5.0 with the kdz extractor tool. This solution don't work for me u.u' can't find qualcom 805 driver...
when i connect phone https://www.dropbox.com/s/uc1yy49a9iyp2t1/Cattura.JPG?dl=0
QHS
danielg90 said:
i folllowed http://forum.xda-developers.com/lg-g3/general/fix-unbrick-lg-g3-stuck-qualcomm-hs-usb-t2933853 and this is the result http://goo.gl/8FSTNp
Click to expand...
Click to collapse
Is your phone in Qualcomm QHSUSB__BULK mode?
If yes I recently got this problem on my D855 after getting an OTA update, it hardbricked, it will need to be boot repaired, the owner of the board diagnostics software is in the thread you got your software from, he restricted his software so that it will give the said error.
He charges 50 USD for repairing boot, I returned my phone to the seller, you should try the software in offline mode, i-e disconnect from the internet before launching the application, if it works then tell us, if not then probably the best option will be to ask the owner of this software for access.
ScAvEnGeR(PHC) said:
Is your phone in Qualcomm QHSUSB__BULK mode?
If yes I recently got this problem on my D855 after getting an OTA update, it hardbricked, it will need to be boot repaired, the owner of the board diagnostics software is in the thread you got your software from, he restricted his software so that it will give the said error.
He charges 50 USD for repairing boot, I returned my phone to the seller, you should try the software in offline mode, i-e disconnect from the internet before launching the application, if it works then tell us, if not then probably the best option will be to ask the owner of this software for access.
Click to expand...
Click to collapse
my device isn't in Qualcomm QHSUSB__BULK mode, is in https://www.dropbox.com/s/uc1yy49a9iyp2t1/Cattura.JPG?dl=0
Good
danielg90 said:
my device isn't in Qualcomm QHSUSB__BULK mode, is in https://www.dropbox.com/s/uc1yy49a9iyp2t1/Cattura.JPG?dl=0
Click to expand...
Click to collapse
Its a good sign, use the LG flash tool, use the TOT method not the KDZ one...
Good Luck...
ScAvEnGeR(PHC) said:
Its a good sign, use the LG flash tool, use the TOT method not the KDZ one...
Good Luck...
Click to expand...
Click to collapse
Any luck with this as im in a similar pickle.
quintaar said:
Any luck with this as im in a similar pickle.
Click to expand...
Click to collapse
What is being displayed in the device manager after installing drivers?
ScAvEnGeR(PHC) said:
Its a good sign, use the LG flash tool, use the TOT method not the KDZ one...
Good Luck...
Click to expand...
Click to collapse
i try lg flash tool method but devide is not detected
ScAvEnGeR(PHC) said:
What is being displayed in the device manager after installing drivers?
Click to expand...
Click to collapse
The com port as in my thread just wanted to check in this post if anyone has any updates too as this one sounds very similar
Hey guys,
I want to update my 5X(7.0, NRD90M) to the September security patch(7.0, NRD90R). I'm currently rooted with TWRP installed. How do I go about doing this? I can't attach to my PC and use the android SDK thingamajig because I don't have an A to C cable. Is there any way to do this on my phone without a PC, or perhaps wirelessly with my PC?
Oh, and, updating and taking the OTA like I normally would does nothing. It tells me the update is downloaded, but when I try to install it, it boots into TWRP and does nothing
Thanks in advance!
Aetheryx said:
Hey guys,
I want to update my 5X(7.0, NRD90M) to the September security patch(7.0, NRD90R). I'm currently rooted with TWRP installed. How do I go about doing this? I can't attach to my PC and use the android SDK thingamajig because I don't have an A to C cable. Is there any way to do this on my phone without a PC, or perhaps wirelessly with my PC?
Oh, and, updating and taking the OTA like I normally would does nothing. It tells me the update is downloaded, but when I try to install it, it boots into TWRP and does nothing
Thanks in advance!
Click to expand...
Click to collapse
Just buy the proper cable and flash a full stock rom (bootloader and radio, boot, system) in fastboot and reroot, afaik you need a non-modifed stock rom to flash an OTA fil.
gee2012 said:
Just buy the proper cable and flash a full stock rom (bootloader and radio, boot, system) in fastboot and reroot, afaik you need a non-modifed stock rom to flash an OTA fil.
Click to expand...
Click to collapse
I understand this is an option, but is there no other solution? I don't have a need whatsoever for an A to C cable currently. If I'd have to buy one it would be just for updating. If this is my only option I think I'll just stick with my current version of Android until I can loan a USB-C PC or something. I don't think I'll spend $15 on a cable I'll only use once a month :/
Aetheryx said:
I understand this is an option, but is there no other solution? I don't have a need whatsoever for an A to C cable currently. If I'd have to buy one it would be just for updating. If this is my only option I think I'll just stick with my current version of Android until I can loan a USB-C PC or something. I don't think I'll spend $15 on a cable I'll only use once a month :/
Click to expand...
Click to collapse
You can try Flashfire http://forum.xda-developers.com/general/paid-software/flashfire-t3075433.
gee2012 said:
You can try Flashfire http://forum.xda-developers.com/general/paid-software/flashfire-t3075433.
Click to expand...
Click to collapse
Are these settings okay? http://imgur.com/tFdGgdJ
Thanks in advance!
Aetheryx said:
Are these settings okay? http://imgur.com/tFdGgdJ
Thanks in advance!
Click to expand...
Click to collapse
Haven`t used it so far to be honest, google to see what you can flash with this app bro. It is supposed to flash full firmwares. Good luck
Hello everyone, I have a Moto G5 (XT1672) and I unlocked the bootloader, and when I went to upgrade the android, on the rainbow screen of installing the update, it simply hung up and did not call anymore, and when I connect it on charger, it simply flashes the white LED ....
I installed the stockrom.net rom stock, the version that was on the phone, which was from android 7.0.
What can this be????
Heeeeeeeeeeeeeeeeeeeeeeeelp!!!!
Lordstark73 said:
Hello everyone, I have a Moto G5 (XT1672) and I unlocked the bootloader, and when I went to upgrade the android, on the rainbow screen of installing the update, it simply hung up and did not call anymore, and when I connect it on charger, it simply flashes the white LED ....
I installed the stockrom.net rom stock, the version that was on the phone, which was from android 7.0.
What can this be????
Heeeeeeeeeeeeeeeeeeeeeeeelp!!!!
Click to expand...
Click to collapse
Today I had the same problem. Please, can anyone help us?
I have tried every button combinations about 20s - 180s. Nothing happen..... When connect it to the computer nothing happens to. No driver is detected. Moto is just dead. Only blink the white led when connected to the wall or computer.
Lordstark73 said:
Hello everyone, I have a Moto G5 (XT1672) and I unlocked the bootloader, and when I went to upgrade the android, on the rainbow screen of installing the update, it simply hung up and did not call anymore, and when I connect it on charger, it simply flashes the white LED ....
I installed the stockrom.net rom stock, the version that was on the phone, which was from android 7.0.
What can this be????
Heeeeeeeeeeeeeeeeeeeeeeeelp!!!!
Click to expand...
Click to collapse
Hello, I'm having the same problem here in Brazil, I read in some Google+ problems that replacing the main board is the only alternative.
But I watched a video of the Moto G4 where Bob Tutoriais (YouTube) can access it through the Qualcomm driver. Could you try to watch and know if you have any similar method? Thank you for your attention.
The problem is that when you connect the device to computer, nothing happens... The motherboard seems not responding... I contacted Motorola today and tomorrow I'll send the device to maintenance.
Has anyone got it?
Sorry, your phone just died. There's no recovery.
Hardbrick. It corrupted the Bootloader partition, so it doesn't exist anymore. The only solution at this time is to replace the motherboard by an new one, in the future we can do Blank Flash, but Motorola did not make these files available.
---------- Post added at 05:11 AM ---------- Previous post was at 05:06 AM ----------
https://forum.xda-developers.com/g5/how-to/urgent-dont-update-stock-rom-unlocked-t3691079
Complicates even more now, I do not know how much a plate is for him ...
Help
I need some urgent help !!!
My Moto G5XT1672 came into hardbrick after an update via OTA. I can not find anything to fix it! I saw in some tutorials of other models a formula using a blankflash, but I can not find it for my model !!! another way is using the medusa box pro, but in my city no assistance has this box !!! help me please.......
Luzini said:
I need some urgent help !!!
My Moto G5XT1672 came into hardbrick after an update via OTA. I can not find anything to fix it! I saw in some tutorials of other models a formula using a blankflash, but I can not find it for my model !!! another way is using the medusa box pro, but in my city no assistance has this box !!! help me please.......
Click to expand...
Click to collapse
Please stop spamming xda threads with the same question - its against the xda rules to which you agreed to when you signed up
There are currently no known working blank flash files for this device
You can try the mmcblk0 method but if it doesn't work for you there's nothing you can do other than pay for a motherboard replacement or a repair shop with tools to re-image the phone
TheFixItMan said:
Please stop spamming xda threads with the same question - its against the xda rules to which you agreed to when you signed up
There are currently no known working blank flash files for this device
You can try the mmcblk0 method but if it doesn't work for you there's nothing you can do other than pay for a motherboard replacement or a repair shop with tools to re-image the phone
Click to expand...
Click to collapse
If you want this is Cedric blankflash
h3sh11 said:
If you want this is Cedric blankflash
Click to expand...
Click to collapse
Where did you get this from
If it was from vache site it's already confirmed not working
If its the one posted in general section - again confirmed not working
h3sh11 said:
If you want this is Cedric blankflash
Click to expand...
Click to collapse
Unknown or damaged file
TheFixItMan said:
Where did you get this from
If it was from vache site it's already confirmed not working
If its the one posted in general section - again confirmed not working
Click to expand...
Click to collapse
+1 :good:
TheFixItMan said:
Where did you get this from
If it was from vache site it's already confirmed not working
If its the one posted in general section - again confirmed not working
Click to expand...
Click to collapse
takoa said:
Unknown or damaged file
+1 :good:
Click to expand...
Click to collapse
Yes It's the Vache blankflash, I tried last night and it does not even work, we can only wait for someone to start working on the mmcblk0 file :good:
Lordstark73 said:
Hello everyone, I have a Moto G5 (XT1672) and I unlocked the bootloader, and when I went to upgrade the android, on the rainbow screen of installing the update, it simply hung up and did not call anymore, and when I connect it on charger, it simply flashes the white LED ....
I installed the stockrom.net rom stock, the version that was on the phone, which was from android 7.0.
What can this be????
Heeeeeeeeeeeeeeeeeeeeeeeelp!!!!
Click to expand...
Click to collapse
guiasaph said:
Today I had the same problem. Please, can anyone help us?
I have tried every button combinations about 20s - 180s. Nothing happen..... When connect it to the computer nothing happens to. No driver is detected. Moto is just dead. Only blink the white led when connected to the wall or computer.
Click to expand...
Click to collapse
Derovile said:
Hello, I'm having the same problem here in Brazil, I read in some Google+ problems that replacing the main board is the only alternative.
But I watched a video of the Moto G4 where Bob Tutoriais (YouTube) can access it through the Qualcomm driver. Could you try to watch and know if you have any similar method? Thank you for your attention.
Click to expand...
Click to collapse
Solution is here
click here to goto my unbrick thread
Hello everybody.
My pixel 2 xl non rooted with unlocked bootloader.
So, Is it possible to flash latest OTA update directly through the phone via stock recovery?
As you aware that with the known and common pixel 2 xl issue which you can't get it connected to PC.
I'm stuck on October update and I'd be glad if someone could help me out on this matter.
thanks in advance.
ahadon1 said:
Hello everybody.
My pixel 2 xl non rooted with unlocked bootloader.
So, Is it possible to flash latest OTA update directly through the phone via stock recovery?
As you aware that with the known and common pixel 2 xl issue which you can't get it connected to PC.
I'm stuck on October update and I'd be glad if someone could help me out on this matter.
thanks in advance.
Click to expand...
Click to collapse
Can't do OTA with unlocked bootloader you'll need to re lock it to do that
ahadon1 said:
Hello everybody.
My pixel 2 xl non rooted with unlocked bootloader.
So, Is it possible to flash latest OTA update directly through the phone via stock recovery?
As you aware that with the known and common pixel 2 xl issue which you can't get it connected to PC.
I'm stuck on October update and I'd be glad if someone could help me out on this matter.
thanks in advance.
Click to expand...
Click to collapse
tylermrsh said:
Can't do OTA with unlocked bootloader you'll need to re lock it to do that
Click to expand...
Click to collapse
Unfortunately, if you can't get pc to phone recognition, your kinda stuck. Have you tried revoking USB debugging to your pc then add it again? Tried uninstalling/installing your drivers? Tried multiple USB 2.0 cables and usb ports and/or another pc? If you can get into fastboot and install twrp you could flash the OTA that way as well. Best of luck to you.
Yes i did revoked it and tried many workaround solutions but unfortunately without luck.
So i thought if might be there's a solution without PC.
Thank you guys for the replies.
Badger50 said:
Unfortunately, if you can't get pc to phone recognition, your kinda stuck. Have you tried revoking USB debugging to your pc then add it again? Tried uninstalling/installing your drivers? Tried multiple USB 2.0 cables and usb ports and/or another pc? If you can get into fastboot and install twrp you could flash the OTA that way as well. Best of luck to you.
Click to expand...
Click to collapse
Tried all above but no luck ?
If someone could suggest any solution would be appreciated.
ahadon1 said:
Tried all above but no luck
If someone could suggest any solution would be appreciated.
Click to expand...
Click to collapse
You may have a broken usb-c port. You need to fix that first, and then re-lock.
My suggestion is that you send your Pixel for repair. If you search google with pixel 2xl usb-c port repair, you will certainly find some repair center near you.