Related
I've got a HTC Desire which has been rooted and Im running Sandvold's ICS. I needed to reboot my phone the other day and after the reboot my camera shows a black screen of death. I first thought it might be a corrupted OS - I reinstall, restores a previous working backing, factory reset - none of them helped which leads me to believe its a hardware fault.
When I run the camera I get a black screen and sometimes a popup that says camera is not responding.
I download a flashlight app and the camera LED doesn't appear to work either - it also says flashlight is not responding.
I though replacing the camera module might do the trick but the flashlight is not part of the module? Anyone has any similar problems?
When you say black screen of death (widely known among windows OS users as KSOD), do you then mean a black screen followed by a system crash which is resolved by pulling out the battery or a black screen followed by system reboot?
try a non ICS rom... think camera is pretty unstable on ICS rom
Thanks - I'll try and go back to stock and see.
I just get a black screen - no OS crash. I can go back and everything is still working fine - no reboots.
Update: Ok - it must be a hardware problem.
I've gone back to CM7 - factory reset/new SD card. Still the same problem.
Update2: Ok - its fixed. Let hope this helps someone else. I opened the phone up and removed the top board and then saw one of the ribbon cables was loose (the one on the left) I reseated it and now camera and flash work perfectly again! Woo hoo!!
flexi cable loose connection to the lower board (the board with the SIM reader)
many thanks !
after disassembling the phone, the connector , the one on the left was not very well connected to the board, so i removed both boards, upper one with the camera and lower one with the sim card reader
plugging it back, and assembling everything made it all work
in my case, the following was not working:
camera
flash
mic jack
now it is all working perfect !!
to see how to disassemble it: check youtube desire disassemble
kl1k said:
Thanks - I'll try and go back to stock and see.
I just get a black screen - no OS crash. I can go back and everything is still working fine - no reboots.
Update: Ok - it must be a hardware problem.
I've gone back to CM7 - factory reset/new SD card. Still the same problem.
Update2: Ok - its fixed. Let hope this helps someone else. I opened the phone up and removed the top board and then saw one of the ribbon cables was loose (the one on the left) I reseated it and now camera and flash work perfectly again! Woo hoo!!
Click to expand...
Click to collapse
Hello there
Im hoping that someone here can help me since im ready to seel the pho for spare parts... i've tried it all.
Heres the deal:
- The phone boots well and if i connect it through usb to the computer i can even access the folders and all.
- I can take photos (i her the sound of the shutter and all and see the piics taken in the folder when connected to the computer) and screnshots
- I managed to restore the phone back to original settings and even update software with sony official soft.
- Inicialy i bought the phone as faulty to try and fix it since the buyer informed me there was no water damage ( and i can confirm this because the "stickers" only show white). He informed that the phone just stoped showing image on screen.
- I thought it was a problem with the LCd so i bought a new one and replace it. The problem persists. Everything works but the screen.
Any toughts on this one? Could the motherboard be faulty in only one place (image, proximity sensor, etc)?
Thanks for you time
Regards
Try the service manuals...
edinacio said:
Hello there
Click to expand...
Click to collapse
I have fully same faulty 2nd "spare parts" phone.
All works except screen, all as you described.
I checked, in my case problem definitely in screen because if connect main board to really working LCD panel = screen ok.
And vice versa: if connect normal main board to this probably faulty screen = black screen.
Maybe here broken flexible connector.
Also nothing interesting related to this case in service documents.
MTC8-KLD6-V2.81
Rooted with Malaysk's latest ROM
For the past month or so, my phone (HTC M8) has flawlessly mirrored with my Head Unit. THEN came a Marshmallow update. Now my HU/phone mirroring is as follows;
1) Plug Phone into USB port.
a)bug icon shows on phone's top banner
2) Press Easy Connected on Head Unit
a) Four blue bars on HU light up as expected
b) Phone now asks if USB should be used for Screen Mirroring (can only press "Just Once", because "Always" is grayed out)
c) I have tried several different ways to deal with 2.b., but I get the same end result
3) Phone enters Drive Mode (I have also turned this off, but no different result)
4) Head Unit spins its wheels for a while, then claims to enter Screen Mirroring, but all I get is a blank screen with the "Home", "Back", "Exit" buttons on the bottom
a) Phone itself never shows on the Head Unit.
As an aside, I tried to use my phone on Chromecast last week. It look forever to play a single YouTube clip, and when I tried to play a different one, "play" and "pause" would work, but it never actually went to the next video. Pressing play on my phone would start the second video on my phone and also start the FIRST video on the tv.
Any ideas?
Thanks
I also have the same problem. I changed my Note3 on GalaxyS7 and said goodbye to ScrenMirroring I really do not like it. Autoradio should update to Android Lollipop and the problem would disappear. But if even our AndroidAutoradio live to see the renovation
NYCAR said:
MTC8-KLD6-V2.81
Rooted with Malaysk's latest ROM
For the past month or so, my phone (HTC M8) has flawlessly mirrored with my Head Unit. THEN came a Marshmallow update. Now my HU/phone mirroring is as follows;
1) Plug Phone into USB port.
a)bug icon shows on phone's top banner
2) Press Easy Connected on Head Unit
a) Four blue bars on HU light up as expected
b) Phone now asks if USB should be used for Screen Mirroring (can only press "Just Once", because "Always" is grayed out)
c) I have tried several different ways to deal with 2.b., but I get the same end result
3) Phone enters Drive Mode (I have also turned this off, but no different result)
4) Head Unit spins its wheels for a while, then claims to enter Screen Mirroring, but all I get is a blank screen with the "Home", "Back", "Exit" buttons on the bottom
a) Phone itself never shows on the Head Unit.
As an aside, I tried to use my phone on Chromecast last week. It look forever to play a single YouTube clip, and when I tried to play a different one, "play" and "pause" would work, but it never actually went to the next video. Pressing play on my phone would start the second video on my phone and also start the FIRST video on the tv.
Any ideas?
Thanks
Click to expand...
Click to collapse
Your need updated EasyConnect app that fixes this issue. Due to android versions, here is the updated version of it
xterm305 said:
Your need updated EasyConnect app that fixes this issue. Due to android versions, here is the updated version of it
Click to expand...
Click to collapse
Sadly, I already purchased a new phone. But thanks for the updated app, I'll hold onto it in case my new phone gets an update.
I was looking all over for this, thanks
My new phone updated to Marshmallow last night (against my wishes and despite my efforts to stop it). Now I'm back to not working.
I'll try that updated app, but I'm not holding my breath. All my searching has revealed threads where people have said that the apk will not update and I have not found a single example of someone with Marshmallow who has Screen Mirroring working.
I am pleased to report that the above update to EasyConnected worked and I am now able to mirror my phone (Marshmallow 6.0.1) once again.
I was ok with Marshmallow on my Nexus 6P but cant to mirroring not that I upgraded to Android Nougat 7.0
Hopefully someone like xterm305 will come along again and provide a link to an updated .apk.
In the meantime, try rebooting your head unit. That has worked for me in the past when my phone wouldn't mirror (but, that was not when it updated).
Malaysk has a link to this thread that might help, DanB0Y. Please let us know.
http://forum.xda-developers.com/showpost.php?p=66305928&postcount=2978
I think you need to remove an .apk from your phone and then connect it to your stereo again though the usb.
Hey everybody i have a problem with Easy connected in Honda connect by HRV and i have an error 0x11 its adb-ec not found not exist. Whats is this?
PIFS2 said:
Hey everybody i have a problem with Easy connected in Honda connect by HRV and i have an error 0x11 its adb-ec not found not exist. Whats is this?
Click to expand...
Click to collapse
Enable USB Debugging in Developer settings
I am hoping I can find some help in here with a couple problems I am running into on this system that would make it so much better to me.
The system is basically an Android box utilizing the touch screen and monitor of my Uconnect 8.4 head unit. The naming in the settings is rk3188 and is running on KitKat 4.4.4, so it is some variant of the Android TV boxes. If there are other specs or info that are needed to help in possibly fixing my issues please let me know.
Issue 1: although not major, there is no option to have OK Google from any screen. Having this option for a car system is obviously something helpful. In the settings of the Google App trying to access the menu for OK Google detection doesn't work, so I can't even get to the screen where that option lives. I have the most up to date version of Google App and Google Play Services. I have Google searched on ways to fix this but nothing has brought that ability up. I know Android version 4.4.4 was capable of this. There was another app that utilized Googles voice engine and allowed this function but Google made him stop using their servers and killed that as an option.
Issue 2: this is the biggest bother to me and I could not find anything even related to what's happening in my searches. The system comes loaded with some apps and using Launcher3 for its front end, it has big buttons but offers almost no ability to customize it. The bottom row has apps that you cannot switch out to anything else, and 3 of them I will never be using. The system works but is not as nice as it could look or function. The obvious answer is to use a different launcher which is where the problem arises. I have tried to use Nova and Apex so far with the same very frustrating outcome. After the install everything is great, I can set the screen up to look amazing and add icons and functionality that really make it a great experience. So everything is working lovely then I shut my truck off and go do whatever. The next time I come back I start the truck up everything loads fine, the new launcher and everything I did to it is working just as expected until about 5 minutes in the screen goes black for a second and then the system goes through a factory reset. Really? Are you kidding me? The first couple times I thought maybe I hit something because I hadn't fully put my truck back together but after playing with it more and having the system factory reset 5 other times I have concluded it is related to changing the launcher. I tried Nova first, then I tried Apex with the same outcome and same sequence of events. Obviously it's annoying everytime testing this because updating and reentering my info everytime just to try the launcher again is time consuming. The last test the only thing I did was a different launcher so that has to be it, but why and how can I fix it?
If anyone has any clue how using a different launcher would cause a factory reset to happen please help me out. Or if there is anything I can do to this system to prevent that. My last resort thought would be to root it but I read someone else who has this system that rooting it caused screen layout issues and made things go 90 degrees off? The loaded apps in the system have touch screen calibration and screen resizing which might be necessary for this to function with the monitor.
Thanks for any help.
I spoke with someone else that has the system and they are not having any issues with running a different launcher so something happen to my particular device. I contacted the company and they will be getting me the firmware to refresh it and hopefully that fixes the resetting issue.
i am looking to get this also. I am very curious how you like the device - it looks great though a bit out of date. Waze & email should work well. How much storage does it have? Can you add a sd card or something?
RichTJ99 said:
i am looking to get this also. I am very curious how you like the device - it looks great though a bit out of date. Waze & email should work well. How much storage does it have? Can you add a sd card or something?
Click to expand...
Click to collapse
I'm getting a new unit sent out, it seems there are 2 versions and for whatever reason mine wouldn't let me customize the launcher.
But even though it's outdated, every app I tried worked just fine, they still install the latest versions. The system has 8gb of on board storage and a microSD card slot that is mainly for loading maps for offline navigation. I think you can still access it for other uses, but they have a better option for that. There is a USB input for flash drives or external drives. I tried my 2TB external drive on it and it accessed my movies fine from it.
How did you get it installed? Who?
got any pics?
Actually I would be interested in this too, I have an Alfa Romeo and the Uconnect 6.5 (european version) which isn't that great, it would be nice to attach a sort of box with ARM hardware running on Android and using the display and touch of the existing Uconnect. The question is, how this can be done?
http://www.dodgedurango.net/forums/.../24632-android-phone-uconnect-8-4-screen.html
I would check out this thread. It has two videos that walk you through the entire process - great info!
I also bought this latest Android system V4 2 weeks ago. Auto launcher pro app is very good working. At the moment there is a issue with the system time, which is not correctly synchronized with gps time. Carperformance Team is working on a fix for that. How can I get root Access for this Android 7 System?
Diabollon said:
I also bought this latest Android system V4 2 weeks ago. Auto launcher pro app is very good working. At the moment there is a issue with the system time, which is not correctly synchronized with gps time. Carperformance Team is working on a fix for that. How can I get root Access for this Android 7 System?
Click to expand...
Click to collapse
glad to hear i'm not going crazy with the clock but there is an issue.
I just bought and installed a V4 a couple weeks back too.
i must have left a loose connection cause i keep having to recall the touchscreen for android. I half-arsed the install cause we were leaving for a 2k mile roadtrip the next day- need to take it apart and do it right. Luckily you can connect a usb mouse in to trigger the calibration app.
id also love root- at the moment im trying to figure out if the one usb port is safe to connect an A to A usb cable into to get ADB. apparently on some versions of nvida sheild, you can. If they provide a firmware update for the clock fix then maybe that gets us an image to futz with for root.
a keyboard also works in teh usb port and i've tried a handful of key combos during boot to get to recovery but haven't stumbled on it yet.
I'll post back if i find anything
michaelk said:
glad to hear i'm not going crazy with the clock but there is an issue.
I just bought and installed a V4 a couple weeks back too.
i must have left a loose connection cause i keep having to recall the touchscreen for android. I half-arsed the install cause we were leaving for a 2k mile roadtrip the next day- need to take it apart and do it right. Luckily you can connect a usb mouse in to trigger the calibration app.
id also love root- at the moment im trying to figure out if the one usb port is safe to connect an A to A usb cable into to get ADB. apparently on some versions of nvida sheild, you can. If they provide a firmware update for the clock fix then maybe that gets us an image to futz with for root.
a keyboard also works in teh usb port and i've tried a handful of key combos during boot to get to recovery but haven't stumbled on it yet.
I'll post back if i find anything
Click to expand...
Click to collapse
Hi @michaelk
Good to hear that I am not alone here with this special system V4. Except for the issue with the system time and no root access, I am fully satisfied so far. I hope to fix it soon. If we had root access then we could solve this issue with the system time with some time apps ourselves.
Thank you for your experiences.
Best regards
Diabollon
wiring harness investigation
so played around some today.
I've got an issue where I need to recalibrate the screen almost every time I boot. it seems the box (or card added to the radio?) forgets things and only works the bottom right corner and also seems to rotate 90 degrees at boot. The end result is unusable screen. I think carperformance is just a reseller because of their response. They're friendly and reply quickly but are really unable to help. The first answer was just randomly fiddle with screen and try to find calibrate setting and reboot- that proved impossible and on my own I discovered a 6 dollar USB mouse from the Walmart could be used to navigate to the calibrate app. When I inquired again when it got more frequent they basically said it's not normal and offered no help except to adjust a personalization setting to run calibrate on boot- that only works once that I can figure (might be related to weird time bug)- so I settled on having tasker run calibrate on each boot. I wonder if there is a battery in the box that needs changing but the warranty sticker keeps me out for not- might add an external battery to keep it alive for a longer time to minimize the rebooting
Anyway took everything apart today to double-check and can't find any connection issues. I traced the harness a bit to try and understand a little and basically, the skinny cables run the daughterboard to snag the screen output and the touchscreen input. But i wanted to figure out what is tapped from the radio harness to the large white plug on the box and see if anything going on their .
DISCLAIMER- I NEED TO CONFIRM (it was hot - laughing) but basically seems what is tapped in radio harness is:
1) power and ground also
2) L&R aux audio signal- interesting here is they tapped a single ground (physically next to the right signal) for common. Earlier i had the RAX hack and their harness used a ground for each L&R and their aux input worked all the time without the little plugin shunt thing to trick aux input. When i dug some more and found a pin diagram from mopar I found that the 'left' ground is actually labeled "aux audio device detect signal" I need to play some more to see what happens but my guess is if we put a switch on that to short it to ground then the aux would just work to avoid the hokey plug.
3) Here's the fun- holding the screen to flip inputs could be the daughterboard running things. BUT since it also reacts to the left steering wheel button pack and switches inputs itself when you need the reverse cam- i figured it reads the can bus. and sure enough, it looks like it taps CAN IHS (+) and CAN IHS (-). Very cool that it would get into the whole bus and read anything- BUT since there are other FCA vehicles that don't auto-switch inputs on revers and they have alternate connections it seems the real dev is not involved to update things to sniff for other reverse signals. Reading around here- seems that there is probably a custom serial port someplace in the box that reads this and there's probably no documentation for us to do anything ourselves. But one can hope...
---------- Post added at 06:12 PM ---------- Previous post was at 06:07 PM ----------
michaelk said:
glad to hear i'm not going crazy with the clock but there is an issue.
I just bought and installed a V4 a couple weeks back too.
i must have left a loose connection cause i keep having to recall the touchscreen for android. I half-arsed the install cause we were leaving for a 2k mile roadtrip the next day- need to take it apart and do it right. Luckily you can connect a usb mouse in to trigger the calibration app.
id also love root- at the moment im trying to figure out if the one usb port is safe to connect an A to A usb cable into to get ADB. apparently on some versions of nvida sheild, you can. If they provide a firmware update for the clock fix then maybe that gets us an image to futz with for root.
a keyboard also works in teh usb port and i've tried a handful of key combos during boot to get to recovery but haven't stumbled on it yet.
I'll post back if i find anything
Click to expand...
Click to collapse
So the spec for the chipset for the V4 says it can handle an OTG port and a couple (maybe 3?) other USB ports. Obviously, the box only has the one USB A port visible on the pigtail. I wish we could get in the box and look for a header for the OTG port to help rooting but.... the darn warranty sticker.
on the FCA/Dodge side of things- I have a Durango with a USB port and SD card reader in the dash (USB Media "Hub" Apparently, FCA uses USB Mini B connectors to interconnect all the ports and the radio. They use latching connectors that are keyed but if you undo them there's a standard USB mini B in there. They do some odd male/female things so you have to pay attention to where you undo cables, but bottom line you can undo the connector on the back of the dash's USB port and stuff a USB mini B female on it and connect it to whatever host device you want.
I first tried an old laptop in case there's anything weird going on. My Dash "Hub" actually has 2 mini-B connectors and a multipin auto harness. Without the harness when you connect it to windows it sees a USB Hub, but the USB port was still dead. So I assumed it needs power from the harness on the back of the dash hub and connected that. UP popped up a USB mass storage device which I believe is the SD card reader- didn't get around to confirming and then the USB port also comes to life. Knowing that it was safe at that point I connected it to the USB A Host port on the box and presto chango now I have the in-dash port connected to the android tv box without any exposed wiring.
Connected the "android auto dongle" through the cars USB port and that works perfectly. I ordered a used 2 USB dash hub from eBay (later model years have 2 and will see what that does. The pictures of that also show the 2 mini B ports- I'll play some more when I get that. I'm not sure what is in those dongles but from the other folks hacking android auto into older models (by using newer radios) apparently, one port works for android auto and the other doesn't. The scuttle is its a body module programming thing but I wonder if maybe there's something physical in there and so the dongle won't be necessary any longer with the new hub? My other thought is if the two USB min B jacks allow you to connect to 2 different hosts- I would try one on the original Uconnect (in case I ever need to update the software) and the other for the android TV box.
So apparently the android tv box handles hubs just fine. As I mentioned earlier it handles a mouse or USB keyboard fine. Also, I played around and connected my hotspot by USB instead of wifi so the device sees it as a modem and that works just fine- so I assume a USB modem works out of the box too. (again odd if that works that carperformance sells a hotspot and not USB modem- like they don't know what the box can do)
I disassembled my display 2 times until it worked. After the first start, I had a black screen. I thought that was it... After 3 times it finally worked. I also had a cable on the plug which has easily resolved. I think you will also have a loose contact somewhere. One time I also had the display calibration gone. Then I connected my old usb keyboard and could then start the display calibration. I reset the system before. So far, the system works without problems. I also have a passive 4-way usb hub to connect.
I have already connected cables for the frontcam but have not yet moved into the engine compartment.
In the video tutorial of Carperformance, you can see when you switch to drive, the display then changes to the frontcam or signal from the cam, but the display does not change to the Frontcam signal with me.
Do you have with you the signal on the display of the camera when switching to drive?
Adw2 = bad mix
Went back and forth many times in email and turns out my calibration issue was probably all ADW2 launcher, guess it conflicts with whatever app they use to communicate with the display.
in the process of troubleshooting I got the update zip for the current version but I don't think those have recovery partition in there and so can't help root? I need to read some more.
I've ripped everything apart like 12 times with the screen, so that my front cam is not connected right now. For the brief time I had it, it was connected to one of the smaller video in pin connectors and don't think it worked in drive by itself, but can't really say for certain. I think certain models can't get the canbus command to see reverse and if I understand they connect in to the video in on the main connector and then use a point on the car that is energized to trigger the switch on that connection. If your adventurous they seem to have to flip a dip also. I think it's the Cherokees or maybe grand Cherokee so maybe Google their thread's? This site gives connector pin outs
http://connectors.dcctools.com/home.htm
There might be a lead for the drive on your shifter if lucky. I think I read the reverse shoulder comes from a body control box in the passenger wheel well?
Also they're super friendly and never wrong when you email but they can be brief. So you could ask if there's a dipswitch to flip to enable auto switching one of the inputs. Hec maybe we should just ask for a table of where the dips do...
(Sorry for any typos... Will try to edit later)
Supposedly it is enough to connect the extra input cable for DVD or CMMB. That answered me Carperformance. Before, I had no external input cable connected. That's why no signal came. The OEM rearcam works flawlessly.
Also, I forgot, they have a workaround for the clock bug
For the clock there is a fix
https://www.youtube.com/watchv=3OEEbah53QY&t=1s
michaelk said:
Also, I forgot, they have a workaround for the clock bug
For the clock there is a fix
https://www.youtube.com/watchv=3OEEbah53QY&t=1s
Click to expand...
Click to collapse
Unfortunately it's not available.
Diabollon said:
Unfortunately it's not available.
Click to expand...
Click to collapse
try this-
https://www.youtube.com/watch?v=3OEEbah53QY&t=1s
michaelk said:
try this-
https://www.youtube.com/watch?v=3OEEbah53QY&t=1s
Click to expand...
Click to collapse
It's a cheaper fix but so no solution. Carperformance should offer a software update with root access. Then we would be satisfied. We should expect it for the money.
My frontcam is working now good.
You already tried Android auto? Which USB dongle do you use? Do you need a special app for this?
My China usb dongle does not want to connect properly with my oneplus 6T.
Edit:
Android auto is working with Pumpkin USB dongle and autoplaybox app. The noname China scrap goes back to shop.
The time fix is working until now also. Thanks for this info. The carperformance, they wrote or informed the affected people who ordered it. I did not get any info.
Diabollon said:
...
My frontcam is working now good.
...
Click to expand...
Click to collapse
besides powering your camera and connecting the yellow RCA video signal did you have to do anything else?
something with the red signal wire maybe?
I cant consistently get a signal on my front cam and not sure if the camera is bad or my setup
---------- Post added at 12:55 PM ---------- Previous post was at 12:42 PM ----------
few other notes for others-
FCA "aux audio device detect signal" harness line is actually normally closed (I think shorted to ground)- if you break the connection the oew radio flips right to aux in. make the connection again and it flips back to previous input.
the in dash usb port is infact a powered hub. I originally had a usb + SD card combo and replaced it with 2 usb port and works fine. FCA uses mini b connections to it- just use a usb a to mini b cable to connect it to the android auto box and your indash usb port(s) will work on android auto (And provide more watts to charge your stuff). oddly either dahs hub has a second usb mini b connector that i played around with a little but never could figure out what it does
more can bus fun! - i updated the dongle firmware on the android auto dongle sold direct from carperforance and now it has a beta feature to map buttons. somehow it seems to be sniffing the canbus through the android tv box. it has arrow keys, numbers, enter, etc and you use the app to select the input to assign then you press the same button on the car twice- it sniffs the signal and assignes it. I My durango has the button packs on the steering wheel and i was able to assign up, down, left, right and get it to have the android auto respond. Need to play more but i think it actually goes android wide. For example i think the down button on my steering wheel was sending page down to the chrome browser i had open on the box. Pretty cool stuff if they expand that.
I just bought a PX5 unit, which seemed to be working perfectly until I finished installing it into my car and now it has become unresponsive with a black screen and a yellow rhombus with an exclamation point in the middle (unable to upload image as new user).
If I turn off the ignition, it will turn the stereo off and the android screen briefly shows before going into sleep. None of the buttons are allowing me to get past the screen and in to android. The reset button seems to do nothing, android is definitely running in the background, just unsure as to why this screen will not close. Any ideas?
Hi, I think I saw a yellow rhombus with an exclamation point when I was installing my radio and rear view camera was not connected to the radio. I think that it is a warning about missing video signal when radio is displaying live feed from a rear view camera.
So, one explanation for your issue could be that the radio thinks you are reversing, and the rear view camera is not connected to the radio. If I understand it right, radio can switch to rear view camera display mode based on two conditions 1) canbus information 2) +12v trigger signal.
For the condition 2), you could check that nothing is unintentional connected to reverse detect wire. If that does not help, then you could perhaps try to disable reverse view feature in the configuration menu before installing the radio to the car and/or find a working canbus configuration settings.
Please notice that I'm a beginner with Android head units and your problem might well be something totally different!!
Thanks for your reply. Some of your post seems to relate to my issue definitely, I think it is linked to the rear view camera which is currently disconnected. However I am unable to get into any configuration options. None of the buttons/resets I try get me past the exclamation screen, I can only see android once I turn off my ignition when it tells me it is closing down. None of the various reset button combinations seem to do anything with my head unit either, can't seem to reset it properly. Its strange, I will reattach the camera tomorrow and see if that brings any joy. I don't know anything about this stuff myself but I am wondering if I did something to the head unit to brick the non-android side somehow.
Edit: Unfortunately reattaching the camera did not change anything.
Update. I have managed to find a way in to the Android side if I connect my phone via bluetooth to the stereo, it then lets me use the split screen function via the top bar menu to put the warning screen other screen to the side, however whenever I touch the screen or attempt to use the android interface, my stereo goes back to the warning screen, none of my inputs via the stereo buttons or the touch screen seem to be registering with the Android side? Very confused. I have also tried as many button combination resets I can find and I have not been able to successfully get into the recovery menu, or any change except rebooting.
Was your unit professionally installed?
Also, what did the re-seller suggest when you contacted them for support?
No the unit was not professionally installed. I am not sure how I've become stuck with the problem. I made some minor changes in factory settings but nothing I thought would of caused this. The seller is yet to respond and its been a couple of days, but I have requested the hardware reset methods for this unit or any other solutions.
deano35 said:
No the unit was not professionally installed. I am not sure how I've become stuck with the problem. I made some minor changes in factory settings but nothing I thought would of caused this. The seller is yet to respond and its been a couple of days, but I have requested the hardware reset methods for this unit or any other solutions.
Click to expand...
Click to collapse
Check the reverse wire on the back of the unit...if necessary disconnect it to ensure no reverse signal is received.
If your unit can boot into android normally then you will have to figure out why the reverse wire is receiving signal .
Check your connectors to avoid any of them to be loose.
Enviado desde mi SM-G950F mediante Tapatalk
Everything has been disconnected from the unit except the power cable to car and and canbus, from what I can tell nothing is loose. Unit will not boot without the canbus box whatsoever, not sure if that is meant to happen.
deano35 said:
Everything has been disconnected from the unit except the power cable to car and and canbus, from what I can tell nothing is loose. Unit will not boot without the canbus box whatsoever, not sure if that is meant to happen.
Click to expand...
Click to collapse
Yes, canbus decoder need to be connected for power up the HU. If you dont need the decoder box you need rewire the harness.
I think I am going to have to request a refund and return it. Still no reply from the reseller and I am not sure what else I can try, everything that is not needed to power it has now been removed. I can't send links or else I would update the thread with a video of the touch/physical buttons being completely unresponsive even when I manage to get to Android. The unit has definitely developed a fault and I am unable to reset it. Admittedly it could be my fault somehow as it was working for the first few boots, but unless they give me something to try I am just going to have to send it back.
Quick bump. Has anyone got any further ideas? I bought off Aliexpress so contact with the seller is slow and painful, they do not seem to understand the issue and just keep telling me to disconnect all wires and reconnect. Which has been done many times. If anyone wants to post a link to the video for me I would be happy to send them it privately.
deano35 said:
Quick bump. Has anyone got any further ideas? I bought off Aliexpress so contact with the seller is slow and painful, they do not seem to understand the issue and just keep telling me to disconnect all wires and reconnect. Which has been done many times. If anyone wants to post a link to the video for me I would be happy to send them it privately.
Click to expand...
Click to collapse
I would start a dispute with them. I had a device that they sent with similar problems and plenty of issues, which they would not help with or would not understand. Best option is to dispute to get a new device or a full refund. Could you send the video?
xLeviNx said:
I would start a dispute with them. I had a device that they sent with similar problems and plenty of issues, which they would not help with or would not understand. Best option is to dispute to get a new device or a full refund. Could you send the video?
Click to expand...
Click to collapse
Yeh I have a dispute open currently, just was hoping it would inspire the seller to actually offer up a working way of resetting the device. Had to add link below seperately as needed to be ten or most posts.
https://www.youtube.com/watch?v=ujHacKESAT8&feature=youtu.be
The stereo defaults as the warning image black screen and I can only get android up using the multiwindow button with a long press. Then the android side will not register any input and will keep trying to put the black screen to the front.
Update: I have been told by Aliexpress I can have a partial refund and keep the unit, or a full refund if I return to China. Anyone have any ideas how I would go about resetting the unit if I took the partial refund? To be honest I think my only option is to return it and get the full amount back but any ideas would be welcome! Shipping to China and awaiting a refund is going to take weeks, would rather just get it working if possible.
deano35: any progres? I have the same problem as you. This is my post from PX5 MTCD/E Head Unit Discussion Thread
" Hi , I have https://s.click.aliexpress.com/e/DtwdJIt its px5, Mtce_gs_v2.90c. Now I have a little problem with rear camera. I bought reverse camera and tried to connect it into front camera input(I was curious how it would look like) and since then its stuck on camera view. Even after disconnecting camera. Only solution was disable "prohibit reverse" in factory settings menu, but with "prohibit reverse" disabled is obviously not showing reverse camera when I gear the reverse down. Everything is shown in this video. https://photos.app.goo.gl/XbYUHApzT8qTezkq6 Thanks for any advice. "
Take a look on the video, its similar as yours.