I just received the phone and tried to use it with this dock with no results (the power led lights on and android P notifications shows the connection with a USB device, however it is not properly recognized).
I tried with an USB key, a mSD and with a HDMI cable attached. Any advice on alternative solutions? (both HW and SW).
I wish I could relate or let alone try to understand what you just said. I would have been fine with typos , but clearly your sentence structure is off even without proper punctuation. Regardless, thank you for the information sir.
Sent from my GM1917 using Tapatalk
Hentai_expert said:
I wish I could relate or let alone try to understand what you just said. I would have been fine with typos , but clearly your sentence structure is off even without proper punctuation. Regardless, thank you for the information sir.
Sent from my GM1917 using Tapatalk
Click to expand...
Click to collapse
Thanks for the tip Sir. I rewrote the sentences in a clearer way to make them easily understandable.
I was using a third party DASH cable originally for my OP3, with my OP7P and noticed it does the same thing as your dock. Side note the OP7P could not be recognized in fastboot with said third party DASH cable.
But the OEM cable works without fail ever time could be pin/or chip? configuration but I don't know enough about Warp/DASH/VOOC to say.
graycatgrayhat said:
I was using a third party DASH cable originally for my OP3, with my OP7P and noticed it does the same thing as your dock. Side note the OP7P could not be recognized in fastboot with said third party DASH cable.
But the OEM cable works without fail ever time could be pin/or chip? configuration but I don't know enough about Warp/DASH/VOOC to say.
Click to expand...
Click to collapse
I made some further tests and these are the results:
- With the dock powered with a PD cable (so charging the phone as well) the video signal works as expected but no other devices are recognized (I tried a USB key, a keyboard and the usual microSD but none are visible)
- Using a simple USB-C to HDMI cable the video out works like a charm
I think the USB issue might be related to the drivers needed to identify the device (a similar situation happened to me on the Nexus 7 several years ago and I fixed it changing the kernel). For now I think I will have to find a different dock. The best one for my needs should have 2 USB, mSD slot, HDMI and Ethernet. Any tips?
SimoxTav said:
I made some further tests and these are the results:
- With the dock powered with a PD cable (so charging the phone as well) the video signal works as expected but no other devices are recognized (I tried a USB key, a keyboard and the usual microSD but none are visible)
- Using a simple USB-C to HDMI cable the video out works like a charm
I think the USB issue might be related to the drivers needed to identify the device (a similar situation happened to me on the Nexus 7 several years ago and I fixed it changing the kernel). For now I think I will have to find a different dock. The best one for my needs should have 2 USB, mSD slot, HDMI and Ethernet. Any tips?
Click to expand...
Click to collapse
One further update:
I used the same dock on the Mi A1 with Android P and it is properly recognized with both the mSD and the USB key attached. Obviously there is no HDMI out since the port is only a USB 2.0 one rather than a 3.1 like the OP7P.
At this point I think it might be related to drivers only, because the notification for an attached USB is there but it is not simply recognized (to be honest if i use the PD-USB while having the mSD inserted, the phone is charged but no popup for attached USB device is shown in that case).
SimoxTav said:
One further update:
I used the same dock on the Mi A1 with Android P and it is properly recognized with both the mSD and the USB key attached. Obviously there is no HDMI out since the port is only a USB 2.0 one rather than a 3.1 like the OP7P.
At this point I think it might be related to drivers only, because the notification for an attached USB is there but it is not simply recognized (to be honest if i use the PD-USB while having the mSD inserted, the phone is charged but no popup for attached USB device is shown in that case).
Click to expand...
Click to collapse
Yeah I'm having the same issue, tried an HP dock and a Dell dock. Neither one supported USB. I don't understand why this is, never had this issue on older model Android phones. Must be the drivers.
FYI - The HP one displayed the picture on the monitor via HDMI, but wouldn't charge the phone. Dell one would charge, but wouldn't support the monitor. I have another model Dell dock that I'm going to try next week that I think will work better.
Another quick update.
All the test were performed with OTG on and with USB debug enabled and disabled to see if there are any differences in results(no differences for now)
Atzbee Dock
- HDMI Out working even without an external power source
- No USB drive/key detected
- Phone charging works
EC Technology Dock
- HDMI Out working even without an external power source
- No USB drive/key detected
- Phone charging works
So how can we escalate this to OnePlus? We should not be having these problems.
I made some further tests with several devices.
original OP OTG
Works with every device so far (not tested with Ethernet)
Vava 8 in 1 old & Vava 8 in 1 new
HDMI, USB flash, sd card and transflash work at the same time (even without an external power source).
I am finding problems in the connection of a keyboard or mouse that are never recognized (except for the original OTG cable)
Ethernet is never recognized.
To make sure before I buy one, the vava 8 in 1 hub works with usb flash drive while charging the phone?
ebolam said:
To make sure before I buy one, the vava 8 in 1 hub works with usb flash drive while charging the phone?
Click to expand...
Click to collapse
Yes (on USB 3.0), however it is confirmed that is a limitation of the kernel, since flashing a different one seems to make everything work smoothly as reported here.
SimoxTav said:
Yes (on USB 3.0), however it is confirmed that is a limitation of the kernel, since flashing a different one seems to make everything work smoothly as reported here.
Click to expand...
Click to collapse
So it only works on a modified device? (unlocked bootloader, flash new kernel) stock does not work?
ebolam said:
So it only works on a modified device? (unlocked bootloader, flash new kernel) stock does not work?
Click to expand...
Click to collapse
it works on USB .3.0 on hubs with stock kernel, but no keyboards or mouse (charging always worked for me). Modifying is needed to achieve the full functionality of the hub
You have to flash a custom kernel to get the USB type C keyboard and mouse working! Stock kernel does not work! Flash it and whalla! read my thread. https://forum.xda-developers.com/oneplus-7-pro/help/otg-usb-hub-recognizing-mouse-keyboard-t3936188
I just want to report that this issue has been resolved with Android 10. The HP dock I was using now supports the keyboard and mouse. Display and charging also still works.
Well that's a huge bummer, I regret buying the tmo variant. I reported this and chatted with one of the people there about pd+otg issues. I am able to get usb hubs to work if plugged into a c-typeA(f) adapter. That of course means no PD or HDMI, so it's awesome that Android 10 includes that fix!
Sent from my GM1915 using Tapatalk
quentin0 said:
I just want to report that this issue has been resolved with Android 10. The HP dock I was using now supports the keyboard and mouse. Display and charging also still works.
Click to expand...
Click to collapse
Hello quentin0, could you please share with us the model of the hp dock you are using ? Thanks a lot !
Everything works, SD card, Ethernet, HDMI (Desktop mode or Mirror which one you want), Keyboard, Mouse, Flash drive. https://www.amazon.com/gp/aw/d/B07XRJDMLD?psc=1&ref=ppx_pop_mob_b_asin_title
Rooted but stock kernel even charge the phone but slowly if you supply external power.
Android 10.3
Wow exactly what I was looking for... Thx a lot !
Related
Anyone know if it's possible to use MHL in conjunction with a microUSB to USB host adaptor to output to HDMI and access an external USB drive at the same time? That'd make the SGS2 an amazing portable media unit.
No, it is not posible. Its an either/or connection to the micro USB port.
Shame, because as you say that would really be a great thing. MHL consortium are considering a number of improvements to the 2.0 MHL spec, so in future devices this may be a possibility.
So MHL can't be used when I'll plug a USB-Hub?
No, sadly not.
It's a shame - for now I'd prefer micro USB & separate HDMI port so USB can be utilised as well as an external display.
As would I, and a lot of others I suspect.
But you've got 16 GB memory and can copy your stuff to the memory and watch it later via MHL on your Flat? So this is not a big problem, I think
s60mike said:
But you've got 16 GB memory and can copy your stuff to the memory and watch it later via MHL on your Flat? So this is not a big problem, I think
Click to expand...
Click to collapse
Yes, but 16Gb of FAT32 and you can't copy a file > 4Gb
I would use allshare to stream the movie or whatever to your phone from a laptop and connect the phone to TV via the MHL HDMI adapter...that way you have access to ur laptop's data without being hardwired to it
chizzwhizz said:
I would use allshare to stream the movie or whatever to your phone from a laptop and connect the phone to TV via the MHL HDMI adapter...that way you have access to ur laptop's data without being hardwired to it
Click to expand...
Click to collapse
Yes, it helps only if your laptop can't play smoothly a HD video
Has anyone got a generic MHL cable to work with the galaxy s 2 yet?
Sent from my GT-I9100 using Tapatalk
lufcmattylad said:
Has anyone got a generic MHL cable to work with the galaxy s 2 yet?
Sent from my GT-I9100 using Tapatalk
Click to expand...
Click to collapse
Not that I'm aware of...
I bought one from Ebay and can't really do anything good with it. Display shows briefly for 3-4 seconds on TV then disappears again. Don't know why.....I hope it's not the device itself because I tested 2 phones, they were bought at the same time, but none of them would work correctly....
If by generic you mean a not samsung one or one not dedicated to the SGS2 then i actually use a one, from ebay or someting like that, everything works perfect you just cant forget to plug power to it, and about the not working one, it seems mine gets jammed by gsm signal (i.e. when receiving a call), so from time to time the image disappears in a blink of noise, maybe that is your problem too, try it in airplane mode.
Oh, I think I misread that question - I have actually used a generic one with my SGSII (a prototype from the MHL consortium) and it worked fine!
chizzwhizz said:
I would use allshare to stream the movie or whatever to your phone from a laptop and connect the phone to TV via the MHL HDMI adapter...that way you have access to ur laptop's data without being hardwired to it
Click to expand...
Click to collapse
No, you can't, when the MHL is connected, the WiFi stops working, I regret not having bought the Optimus 2x
erebocln said:
No, you can't, when the MHL is connected, the WiFi stops working, I regret not having bought the Optimus 2x
Click to expand...
Click to collapse
Uhm no. I've been streaming with WIFI through MHL no problem for MONTHS. Using the Original Samsung MHL connector of course.
I have to put mine in offline mode to be able to use the MHL adapter.....
As for USB-OTG no luck yet.....
On Amazon, Ebay, DealExtrem ... you will find adapters that can do 3 things at a time:
- output HDMI
- let phone work as usb host, so that you can plug kbd, mouse, and external HDD (second wifi card, wired ethernet ...); once you have the usb A plug, just pub a hub
- recharge the phone (what is not possible with the legacy short OTG cable).
+ read memory cards
Such devices are sold as MHL devices. Some MHL devices don't to all that.
Take care. MHLv2 is more complex than MHLv1.
doublehp said:
On Amazon, Ebay, DealExtrem ... you will find adapters that can do 3 things at a time:
- output HDMI
- let phone work as usb host, so that you can plug kbd, mouse, and external HDD (second wifi card, wired ethernet ...); once you have the usb A plug, just pub a hub
- recharge the phone (what is not possible with the legacy short OTG cable).
+ read memory cards
Such devices are sold as MHL devices. Some MHL devices don't to all that.
Take care. MHLv2 is more complex than MHLv1.
Click to expand...
Click to collapse
Could you post a link as an example for such a device, that works properly (if you've tested, or you know it works) ?
Thank you
I can post links, but ... I have not tested any of those. And don't know any one personally who tested it.
Cable:
http://www.amazon.com/Juiced-Systems-MHL-Adapter-MicroSDHC/dp/B008CQKM2U
http://www.dx.com/p/5-in-1-micro-us...n-micro-usb-adapter-black-257780#.U8HYDNePul0
Monobloc:
http://www.ebay.fr/itm/Micro-USB-Ho..._MobilePhoneDataCables_JN&hash=item258600844e
I don't like the monobloc version; I fear it's too heavy, and may help breaking the phone plug.
There are all sorts of OTG and MHL cables. I have seen OTG dongles as short as 4cm (monobloc), with small cable (8cm: 4-8€), with long cable (1.5m .... should be 7 feet), pure HDMI (passive cable, no card reader, 8-12€), VGA (including very cheap HDMI to VGA converter, 20-30€ ... including sound output). In some case, you need to buy accessories (extra power supply, extra uUSB cable, extra HDMI cable). Also seen a very cute hybrid card reader: http://dx.com/p/285865 (I love this product design, and I love this URL syntax )
Don't forget that there can be mistakes in item description.
Here I have described how to build an external battery:
http://forum.xda-developers.com/showpost.php?p=54036759&postcount=17
On previous phone, I just soldered additional battery to internal one; on my new phone, I will do something more complex, and more flexible.
Loosing power via OTG/MHL is not a fatality. Most phone have an other hidden power input:
généric, that uses the USB plug:
http://www.dx.com/p/reverse-qi-wire...arger-receiver-for-micro-usb-cellphone-312805
TRIPLE CHECK POLARITY; I took the wrong one; have to fold the cable.
So ... even if your OTG/MHL module takes power from your USB, and can not recharge your phone, the specific shell can charge your phone the other way So, you need to build an internal specific module:
https://www.youtube.com/watch?v=UK7PRJ4SiK0
S2 specific back shell, so called receiver:
http://www.aliexpress.com/item/2013-newest-wireless-charger-for-samsung-galaxy-s2/1266101036.html
http://www.exportprive.com/en/batte...reless-charger-set-for-samsung-galaxy-s2.html
http://www.alibaba.com/product-detail/QI-Wireless-Charger-for-Samsung-Galaxy_821969998.html?s=p
The SGS2 is not designed to accept wireless chargers, so, you have two options:
- solder and take the pins out (cf youtube) (do not solder coild to battery, or you could overcharge the batt, and burn your phone ... I mean, physically set fire)
- find an item that includes back shell + specific battery (exportprive)
Many recent phones have the internal connectors, so you just need to change the back-cover. In this case, the software will be able to know the charger is wireless (as opposed to AC, and USB; advanced battery tools will show those 3 possibilities). I believe the motherboard for my HTC One M8 is designed to have those pins, but I can't find the specific cover yet (maybe in a few months); only found it for M7.
I just recently got a Samsung Galaxy Note 10.1 and so far I'm quite happy with it --- except one thing, I cant find a cable that lets me charge the tablet *and* use the USB Host (OTG) port... (i.e. read files off a USB drive or play a game with a USB game pad while keeping the tablet plugged in)
Is there a way to do this? it would seem to me that all it needs is a splice to give power to the Power +/- pins on the connector while keeping the OTG Data +/- pins active...? (I know nothing about the pinout so I could be wrong on this)
Just to be clear I want to use the OTG adapter WHILE CHARGING (I've found one device that gives both these options but says "only one function may be used at a time")
Ideas?
Discussed dozen times in 10.1 forum. Actually it is not possible. Build an otg + power cable myself but it only works with timing and with a specific procedure... quite annoying. Wait for a custom rom somewhere in the future as I do.
You may have issues trying this, OTG cables are iffy under Jelly Bean. Some may work, some may not. In fact, Google removed references to OTG support for Nexus devices last November since OTG is so spotty. Splicing a cable that might work may kill it. Decent battery-powered USB and SD hubs are available and bypass the OTG problems. I have the RavPower RP WD01 and love it. The USB port will support drives upto 3T. It also has an SD card slot.
mke1973 said:
You may have issues trying this, OTG cables are iffy under Jelly Bean. Some may work, some may not. In fact, Google removed references to OTG support for Nexus devices last November since OTG is so spotty. Splicing a cable that might work may kill it. Decent battery-powered USB and SD hubs are available and bypass the OTG problems. I have the RavPower RP WD01 and love it. The USB port will support drives upto 3T. It also has an SD card slot.
Click to expand...
Click to collapse
Powering the USB devices isn't a problem, I have a nice hub that powers them without issue, even extremely power-hungry devices. I was wanting to charge the tablet's battery while using the OTG adapter (original thought was for USB-gamepad-ing since high-requirement games drain battery, but I've since started using a PS3 controller over bluetooth so I can use the OEM charge cable and wireless for gaming --- but USB drives I'd have to copy the files over to internal flash or a MicroSD card to view while charging and i've found that the cards dont like files that are 8gb in size... (FAT-32 restriction iirc))
47kt said:
Discussed dozen times in 10.1 forum. Actually it is not possible. Build an otg + power cable myself but it only works with timing and with a specific procedure... quite annoying. Wait for a custom rom somewhere in the future as I do.
Click to expand...
Click to collapse
I saw that when I google'd but thought maybe there had been some new developments (especially with how this site's members love to tinker with electronics and write custom firmware). It's not a huge issue, since the Note 10.1 has amazing battery life (it's actually matching or doing BETTER than my iPad in most circumstances) I just like to never run the battery down low.. (why cant tablets have user-replaceable/swapable batters like most phones?!)
Thanks for the info!
Does anybody know of a working OTG cable for the Nexus 7 2013? If so please reply with a link to Amazon. I am planning to hook up either a ps3 controller or xbox 360 controller.
Sent from my Nexus 7 using xda app-developers app
http://www.amazon.com/gp/product/B0095TEL8Y/ref=oh_details_o06_s00_i00?ie=UTF8&psc=1
Bought it and am using it.
For 2013 version?
Sent from my Nexus 7 using xda app-developers app
Using it right at this very moment on my very own N7 2013 built in July 2013
http://www.amazon.com/gp/product/B0073EPXO4/ref=oh_details_o01_s00_i00?ie=UTF8&psc=1
This is what I'm using. Cheap & works great & is pretty thick, I feel like it'll last long.
I use this one:
http://www.amazon.com/gp/product/B009YPYORM/ref=oh_details_o05_s00_i01?ie=UTF8&psc=1
purchased from seller: Atomic Market for around $10
It has the additional bonus of being able to accept power via its additional USB cable.
I find the Nexus 7 LTE 2013 does not need the additional power for typical USB thumb drives, but it might be needed for other devices like an external disk drive.
I find my Chromecast must have this cable powered in order to use a USB thumb drive to root and replace the android operating system.
You can save a few bucks for a cable that does not provide power if you want.
I also own this one:
http://www.amazon.com/gp/product/B005FUNYSA/ref=oh_details_o03_s00_i00?ie=UTF8&psc=1
(purchased from amazon seller: Digital Center(Ships From Hong Kong)
which only costs $1.49 with free shipping. It was $0.83 when I purchased it last year.
It works on the Nexus 7 LTE 2013 with USB thumb drives, but does NOT provide additional power for devices which may need it.
Can you confirm thath this otg power cable charges the nexus 7 2013 while still reading peripheral data from usb port?
HowardZ said:
I use this one:
http://www.amazon.com/gp/product/B009YPYORM/ref=oh_details_o05_s00_i01?ie=UTF8&psc=1
purchased from seller: Atomic Market for around $10
It has the additional bonus of being able to accept power via its additional USB cable.
I find the Nexus 7 LTE 2013 does not need the additional power for typical USB thumb drives, but it might be needed for other devices like an external disk drive.
I find my Chromecast must have this cable powered in order to use a USB thumb drive to root and replace the android operating system.
You can save a few bucks for a cable that does not provide power if you want.
I also own this one:
http://www.amazon.com/gp/product/B005FUNYSA/ref=oh_details_o03_s00_i00?ie=UTF8&psc=1
(purchased from amazon seller: Digital Center(Ships From Hong Kong)
which only costs $1.49 with free shipping. It was $0.83 when I purchased it last year.
It works on the Nexus 7 LTE 2013 with USB thumb drives, but does NOT provide additional power for devices which may need it.
Click to expand...
Click to collapse
bossman137 said:
Can you confirm thath this otg power cable charges the nexus 7 2013 while still reading peripheral data from usb port?
Click to expand...
Click to collapse
I can only confirm that both OTG cables I own work on the Nexus 7 2013.
i am using one that came with my minix x5 and it works on all my android devices, but the connection is loose. i would be surprised if there was one that did not work as the cable itself is such a simple thing.
i would also like to know of a working powered option. i thought the powered cables only supply power to the accessory, not to charge the device itself.
HowardZ said:
I can only confirm that both OTG cables I own work on the Nexus 7 2013.
Click to expand...
Click to collapse
Since you have the USB OTG cable with the additional cable for charging, would you mind testing it by:
1). Connecting a working USB device (mouse, HDD, etc.)
2). Connecting the USB power to the 2nd cable in the OTG cable
I am trying to use a BT keyboard and non-BT wireless mouse and charge the N7, but unfortunately, it drains the battery down heavily.
PS: I CANNOT use both BT keyboard and mouse AND have Wifi ON, as it interferes with the BT radio, making the keyboard and mouse lag heavily. I have created a thread on this also.
What thread is that?
Sent from my Nexus 7
fackamato said:
What thread is that?
Sent from my Nexus 7
Click to expand...
Click to collapse
This one...
http://forum.xda-developers.com/sho...ess mouse (non-bluetooth) that works with N7?
lanwarrior said:
Since you have the USB OTG cable with the additional cable for charging, would you mind testing it by:
1). Connecting a working USB device (mouse, HDD, etc.)
2). Connecting the USB power to the 2nd cable in the OTG cable
I am trying to use a BT keyboard and non-BT wireless mouse and charge the N7, but unfortunately, it drains the battery down heavily.
PS: I CANNOT use both BT keyboard and mouse AND have Wifi ON, as it interferes with the BT radio, making the keyboard and mouse lag heavily. I have created a thread on this also.
Click to expand...
Click to collapse
I have connected a USB thumb drive. The thumb drive works with or without power attached, but it will not charge. I suppose it is built to provide the power to the attached USB device and not to the phone / tablet.
Regards
Howard
I just got a cable from monoprice and it works great.
http://www.monoprice.com/Product?c_id=108&cp_id=10833&cs_id=1083314&p_id=9724&seq=1&format=2
Has anyone found an OTG cable that can be used to power a thumb drive and apply power to the Nexus 7? I'm trying to find one for when I'm traveling. I'd like to be able to watch movies and keep the device charging.
lanwarrior said:
Since you have the USB OTG cable with the additional cable for charging, would you mind testing it by:
1). Connecting a working USB device (mouse, HDD, etc.)
2). Connecting the USB power to the 2nd cable in the OTG cable
I am trying to use a BT keyboard and non-BT wireless mouse and charge the N7, but unfortunately, it drains the battery down heavily.
PS: I CANNOT use both BT keyboard and mouse AND have Wifi ON, as it interferes with the BT radio, making the keyboard and mouse lag heavily. I have created a thread on this also.
Click to expand...
Click to collapse
Perhaps a small powered USB hub will reduce the power drain on the N7?
Have a look at this.
Some ****ty spam prevention policies don't allow me posting an outside link.
(Seems I haven't posted "enough" to be considered "trustable"
So figure out the url below.
ptth:\\mehrvarz.github.io\usb-host-mode-power-management-nexus7\
xr_ghg said:
Some ****ty spam prevention policies don't allow me posting an outside link.
(Seems I haven't posted "enough" to be considered "trustable"
So figure out the url below.
ptth:\\mehrvarz.github.io\usb-host-mode-power-management-nexus7\
Click to expand...
Click to collapse
Easy enough to figure out...but I will post clickable link for ya http://mehrvarz.github.io/usb-host-mode-power-management-nexus7/
lanwarrior said:
Since you have the USB OTG cable with the additional cable for charging, would you mind testing it by:
1). Connecting a working USB device (mouse, HDD, etc.)
2). Connecting the USB power to the 2nd cable in the OTG cable
I am trying to use a BT keyboard and non-BT wireless mouse and charge the N7, but unfortunately, it drains the battery down heavily.
PS: I CANNOT use both BT keyboard and mouse AND have Wifi ON, as it interferes with the BT radio, making the keyboard and mouse lag heavily. I have created a thread on this also.
Click to expand...
Click to collapse
My y-connector from my n4 doesn't charge while using USB otg. The ability to do so is not written in the software. I'll try to locate the source and report. OTOH, the USB otg connectors from my GNex and N4 all work on my N5 and both old and new N7's.
EDIT: I just ran across this. I'm sure it's for the original N7. I wasn't even aware of it so obviously have not tested it. I did use ziddey's kernel on the N4. Still searching.
2nd EDIT: Available for N7 FLO/DEB 4.4.2. I'm running franco but will revert to stock then try this (as soon as I make a nandroid of my device).
3rd EDIT: That kernel does work to charge while on usb otg. It is a setting you choose to activate during the set-up. I just chose stock everything until I got to the power choices. I will say that although the install was successful, I came as close as I've ever come to thinking my device was bricked. After the install, the screen went black and I couldn't do anything. After about a 30 sec power button mash, everything booted back up. This video shows installation on the N5. Some choices are different on the N7 FHD. As I said above, I was NOT returned to TWRP after installation.
There is a note about altering a sys file for OTG peripherals. I only attached a flash drive and the usb_charge_mode was set to Y (I assume for yes). You may have to perform the edit if using a peripheral device.
Sent from my Nexus 7 using Tapatalk 4
Hey Guys,
I recently bought a Micro to USB OTG cable but unfortunately can't get it to work on my new S Tab(10.5).
I am able to get it to work on my Galaxy S3 phone and old Nexus 7 tab so it appears that the cable works fine. My S Tab is not rooted and currently does have the latest updates. I also ran the OTG checker which verifies that my tablet has the necessary files. When I run the OTG troubleshooter tho it does not appear to be picking up my cable at all.
I originally bought this to use my wired 360 controller on my tablet, the 360 controller and flash memory sticks are the only things I have tested on the cable itself. Like I said above, my S3 and Nexus 7 picks up these 2 devices just fine through the cable.
Anything that I am missing? Any tips/quirks to get this to work?
Thanks so much for your time/help!
P.S. attempted to post link to my exact cable but couldn't because I am a new member.
Are you willing to have device root and flash a custom kernel?
If yes, then my SkyHigh kernel does support OTG and has in-built XPAD (XBOX) controller module and confirmed working by another user. Some games may require you to map the controller with a certain app, some without.
FS support is dependent on kernel. If you are trying to mount NTFS r/w, then you will need to also install Paragon app or navigate to /mnt/ntfs/.... for kernel NTFS r/o
It's possible that it could be your cable. I had problems a couple years ago with an otg cable not working on my Note 2 but working in a couple older devices. It turns out it was because the micro usb end that plugs into the phone was too short to plug in all the way. I'm not sure if it's a new standard or something, but my Note 2, Note 8, S5 and Tab S all seem to have a cable with a longer micro usb tip than any of my previous devices have.
Hold the otg cable next to the charge cable that came with your Tab S and see if the tip of the otg cable is a couple of millimetres shorter. Also plug the charge cable into the tab and notice the way it kind of "clicks" into place when you push it in the last little bit. Now plug in the otg cable and see if it has the same "click" feel. If not, then I'd bet it's your cable. I have an otg cable that specifically states that it's for an S5 and it works perfectly on all the devices mentioned above. I also have a generic otg cable that works on my old galaxy nexus but doesn't work on any of the above devices.
Here's the old thread in case that helps:
http://forum.xda-developers.com/showthread.php?p=43764083
Thanks for the reply's.
I don't really want to go down the Root road because I have never gone through that process and don't feel comfortable with it at this time.
The cable Micro pin portion definitely doesn't fit as snug as the S Tab charger. The OTG cable actually appears to be longer than my S Tab charger Mirco pin. When plugged in you can tell it sticks out a smidge....The thing with that though, it does the same exact thing on my other 2 devices that work with the cable.
Guess it could be the cable, just hate to send this back and order another and be in the same boat.
Mrod862 said:
Thanks for the reply's.
I don't really want to go down the Root road because I have never gone through that process and don't feel comfortable with it at this time.
The cable Micro pin portion definitely doesn't fit as snug as the S Tab charger. The OTG cable actually appears to be longer than my S Tab charger Mirco pin. When plugged in you can tell it sticks out a smidge....The thing with that though, it does the same exact thing on my other 2 devices that work with the cable.
Guess it could be the cable, just hate to send this back and order another and be in the same boat.
Click to expand...
Click to collapse
Cable or no cable, if you wish XPAD controller, then you'll need the kernel or loadable kernel compiled module. Other features (some I described) also require kernel. ... all requiring root.
Since you've ruled that out, you just need to forget many features that are available with some other devices and move on.
Best of luck.
Does anyone know if the Pixel will support OTG without root?
ShaunWinSC said:
Does anyone know if the Pixel will support OTG without root?
Click to expand...
Click to collapse
I think I saw an unpacking video and the OTG adapter was included in the box.
just whacked a mouse into the adapter in the box. works fine.
Also tried with a mem stick, and works fine
What is the use of the USB to USB-C adapter that comes with the cable ?
AstroDigital said:
What is the use of the USB to USB-C adapter that comes with the cable ?
Click to expand...
Click to collapse
I think it was intended to facilitate moving files from an older phone. Mine is due to arrive any moment. I think we will all have some real answers soon.
Except most old phones do not have USB-C
AstroDigital said:
Except most old phones do not have USB-C
Click to expand...
Click to collapse
You plug the USB C end into the Pixel and then use another cable to connect an older phone (presumably one you're already using with the older phone). Micro USB/Lightning into the older phone, USB into the adapter. The adapter can also be utilized for OTG - USB C into the Pixel, flash drive/other USB device into the USB port.
AstroDigital said:
What is the use of the USB to USB-C adapter that comes with the cable ?
Click to expand...
Click to collapse
Also to use OTG. Plug that in, and you can hook up a keyboard, mouse, removable drive, someone elses phone, whatever.
Could someone clarify. I plugged the adapter in how I was directed by a thread at the "pixel community". The thread referenced a way to use the adapter to transfer files however I plugged it in set the settings to xfer files and nothing. Does the adapter go into the pixel or the (in my case) Note 7? The thread listed a way to make these transfers upon start up but I'm way past start up. I need to transfer a couple apps and a big phone log and a truck load of texts. Any help out there?