Related
The screen alignment problem comes back this morning to my HTC Tytn.
It hangs on the calibration screen. Nothing helps...scratching...itching etc.
Now i must flash back to WM5 to change the device at Vodafone Germany. Can i make this with the official file from the vodafone germany website?
At this moment on my Tytn is:
The new Shaps WM6 ROM (German, FULL Version from 28.07.2007)
Radio 1.48
Olipro 2.10
Or did i have to work with any ROM Kitchen? I have read the instructions on MrVanx site and other people says that i only have to flash the original Vodafone update file from the website.
sorry for my terrible english...
I hope you understand what i want....
I also have sceen alignment issues using Schaps WWE ROM. I had mine in for service earlier and do not believe it is hardware related this time, as some WM6 roms seem to give me the problem occasionally (I've tried them all..). I have no problems using Jasjammings black roms, so what it may be beats me... Hopefully there will be a fix.
EDIT... I've done a new flash with the latest Schap ROM, I believe it is better than the one I tried before. I tried Sleuth's as well, but it was too giving me alignment issues. The new ROM seems good so far.
Trieoner said:
The screen alignment problem comes back this morning to my HTC Tytn.
It hangs on the calibration screen. Nothing helps...scratching...itching etc.
Now i must flash back to WM5 to change the device at Vodafone Germany. Can i make this with the official file from the vodafone germany website?
Click to expand...
Click to collapse
I might be wrong but wasn't the screen alignment issue the alignment changing after being set due to problems in hardware with the screen itself?
This sounds like a software fault only that a new ROM would probably fix. (or was the problem that something presses on the screen which stops it calibrating?)
(i never suffered it so havent looked into it)
sambartle said:
I might be wrong but wasn't the screen alignment issue the alignment changing after being set due to problems in hardware with the screen itself?
This sounds like a software fault only that a new ROM would probably fix. (or was the problem that something presses on the screen which stops it calibrating?)
(i never suffered it so havent looked into it)
Click to expand...
Click to collapse
I had a terrible screen alignment issue on my Wizard. It is a hardware failure.
As for the OP's question on downgrading, check out MRVANX's AWESOME GUIDE.
Many thnks 4 the support!
Many thanks todd_jg! This is what i am searching for. I have found another guide but this was i found where an old version of this.
Many many thanks. I will try this guide on weekend.
BTW: Its my third Tytn from Vodafone, the screen alignment problem is definitly a hardware bug as HTC official related in February this year.
Next problem....damn
Ok. the flashing of the original Vodafone Germany ROM is fullfilled! It works...
BUT:
Now i am sticking in the first calibration screen after the first boot (after flashing)!
Because my Tytn has a calibration problem i am unable to do the first calibration to get in the next step of setting up Win Mobile 6 (time and date i think).
AND:
In the (perfect!!!) guide posted above there is an extra guide to downgrade the spl.
But thru the sticking in the first calibration screen i am unable to downgrade cause the update (downgrade is the better name i think) says not connected to device.
Does anybody have an idea to solve this tricky problem?
BTW: changing the device at vodafone i have to wait 17 work days because they have a little delivery problem. I think they dont have any device thats work probaly.... But I can wait.
I hope you understand what i want...sorry i come from Germany...
Have you tried waiting a while for the calibration screen. Sometimes after a new ROM has loaded, it seems to take a while to get the screen to respond to the calibration.
Also, you should be able to do the SPL downgrade as it is explained in Mrvanx guide, except you can start in bootloader mode, instead of starting with the phone on.
Und, dein Englisch ist echt gut. Ueberhaupt keine Probleme dich zu verstehen
I have waiting a very long time after the first boot. Because i have to think about what i do now.
And i have pressed all buttons on the phone and i have punished it for a while cause i am a little bit angry about this sh!t. Nothing helps.
In bootloader mode the downgrade says that there will be a problem with getting contact with the device.
Hier nochmal auf deutsch:
Ich starte das Teil, Vodafone screen..nochmal Vodafone screen...dann WM5 Startbildschirm...dann "Bitte den screen berühren zum einrichten"...dann weißer Bildschirm mit dem Scheiß Kreuz...und dann kann ich es 1000 mal kalibrieren und nix passiert...egal ob aufgeschoben oder nicht.
Wenn ich es im Bootloader das Update starte, dauert es wenn er anfangen will ne ganze Weile und er schmeißt mich raus mit Device ist nicht angeschlossen. Wenn ich das Telefon normal booten tue (WM5 wird gestartet) fängt er an zu synchronisieren und ist verbunden trotz dem Kalibrierbildschirm. Auch da bricht er den downgrade ab.
Ich hoffe ja das Vodafone das Ding gleich wegschmeißt ohne den Versuch einer Reparatur. Wenn einer in den Bootloader schaut gibts bestimmt Ärger denke ich. Aber ich bekomm ja erst den neuen und die dann erst den alten!
Was tun sprach Zeus...
If all else fails, you can try to reflash with the SDCard method. No USB connection needed.
The instructions are in here somewhere.
USB methos is going like this:
Format Your card to FAT32. Rename RUU_signed.nbh to HERMIMG.NBH. Copy this to Your card. Put card in to device and softreset holding Power and Ok button.
You should see grey screen witch question. Press Power button and wait untill process ends. When You see Updated Succed, reset with stylus.
Copied this from another thread (just remembered I read this recently)
Olioaglio
I did this like you have said but when i am entering the bootscreen (4 color screen, i see shortly the grey screen (0,1 sec!) and nothing to see except the screen with ipl 1.04 and spl 2.10olipro.
I copied my files to my computer (nothing on the card) and copied the .nbh file from the downgrade to 1.10 olipro (link in the manual from you) without the .exe file on my card. Then i inserted the card and enter the bootloader screen with power button ok button and softreset.
EDIT: After i had formatted my card it works...
BUT after flafshing the 4 colour screen says: Herm200 IPL-1.04 HERM200 SPL-2.10.Olipro
I copied the file RUU_signed.nbh from the folder HERM_SPL1.1ooli_only_customRUU to the card and renamed it into HERMIMG.nbh
The grey screen appears after the softreset...i push the power button...the update was sucessfully...i sofreset...it boots to the calibration screen from WM5...i get into the bootscren with holding OK Power and Softreset and there are : Herm200 IPL-1.04 HERM200 SPL-2.10.Olipro
What happend wrong? Where I am so stupid? God Damnmnmnmnmnmn....
Hey again!
Try this thread. It may help you to.
Essentially, you will do the following:
* Fire up Custom_RUU
* Manually select the correct SPL (Oli 2.1 and HardSPL option)
* Put the phone in bootloader mode
* THEN plug into USB
* Press continue
Oftentimes, this gets past the cannot connect error.
todd_jg said:
Hey again!
Try this thread. It may help you to.
Essentially, you will do the following:
* Fire up Custom_RUU
* Manually select the correct SPL (Oli 2.1 and HardSPL option)
* Put the phone in bootloader mode
* THEN plug into USB
* Press continue
Oftentimes, this gets past the cannot connect error.
Click to expand...
Click to collapse
OK...i think you and oliaglio are the right guys to help me!
This method above works!
BUT: After the selfmade softreset from the RUUwrapper.exe WM5 boots normally...then i get into the bootloader4colorsscreen and there it was...
ipl 1.04 and spl 2.10olipro
why? please god...change the spl into 1.10...
Trieoner said:
OK...i think you and oliaglio are the right guys to help me!
This method above works!
BUT: After the selfmade softreset from the RUUwrapper.exe WM5 boots normally...then i get into the bootloader4colorsscreen and there it was...
ipl 1.04 and spl 2.10olipro
why? please god...change the spl into 1.10...
Click to expand...
Click to collapse
OMG - I remember I had that problem once. That was a ***** to solve. In fact, it was so tough that MrVanx made a SPECIAL GUIDE FOR SPL DOWNGRADE. We are lucky for this.
Oh yeah, and the reason that it won't change the SPL is because that is exactly what HardSPL does - it protects the SPL from being overwritten, since THAT is what bricks phones. Trust me, it is for your own good (and mine too - notice my avatar!). Make sure that the SPL downgrade is the last flash operation you perform.
What does your text mean? I dont understand what you have written.
Is it possible for me to downgrade or not? when i use the guide it doesnt work for me. I am a little bit confused....
My school english is so terrible...****.
No more ideas todd and oliaglio?
Please help me...
The downgrade guide hould work if done properly. Use the files in the links in the downgrade guide. It is hard to replace Oli 2.1 - everything will work except that. Just like you described. But this step:
The first step is to dowgrade to SPLversion 1.10.oli. Firstly download this archive and extract the files to a temporary folder, connect your device up via the USB port and allow it to connect to activesync. Run "RUUWrapper.exe" which will fire up the RUU program.
Click to expand...
Click to collapse
is most important. That will write over Oli 2.1 and get it to Oli 1.1. After that, you can put whatever SPL you want on there. Be sure to use the Oli 1.1 link in the thread.
so actually by following the guide, I can choose SPL 1.11 instead of the listed SPL's 1.04 and 1.06 ?
Is it like, if I install the swedish ship version, the spl will go back to 1.11? And after I have done that, I can install the official norwegian WM6 ROM?
Hello everybody,
I have tried to upgrade my Diamond with a new Radio ROM but it didn't work.
Now I'm blocked to a screen wich says :"
"Upgrade ROM code Error"
Even I have tried to make a har reset, I always obtain this screen.
Is there a way to connect the Diamond to my PC with the usb cable in order to delete the bad file (Radio ROM).
If it's possible, i think, it will boot normally ...
Thanks a lot !
Enter bootloader mode and reflash another Radio.
How can I do to enter in Bootloader Mode ???
danaobrest78 said:
How can I do to enter in Bootloader Mode ???
Click to expand...
Click to collapse
Google as well as the search function of this forum both know.
here you go
hope this helps
http://forum.xda-developers.com/showthread.php?t=405659
Hi every body,I am new here i was wondering if i can put english language in my htc touch pro 2,he's now runing on german,the phone is one 6.5 windows,i can see that it has german rom,can somebody give me step by step proces how to put english rom in my phone,also will that lock the phone,because it works on every network now,i don't know is it simfree,i bought it like this.
thanks to you alll.
greeting.
p.s. sorry for my bad english.
can anybody help me?
a searched over this forum i found that i have to first hardpsl my phone so than i can put some rom in it,i want any english rom,because it is now on a german,and i don't know german language.
i have on question will phone lock when i do hardspl,because now it works on every network?
please answer.
thanks.
also,how to tell is my htc touch pro cdma or gsm,i saw that that is very importnant.
thanks.
djole199 said:
can anybody help me?
a searched over this forum i found that i have to first hardpsl my phone so than i can put some rom in it,i want any english rom,because it is now on a german,and i don't know german language.
i have on question will phone lock when i do hardspl,because now it works on every network?
please answer.
thanks.
also,how to tell is my htc touch pro cdma or gsm,i saw that that is very importnant.
thanks.
Click to expand...
Click to collapse
yeah, you should Hard-SPL first, it won't lock the SIM, don't worry
if it is german then it is a GSM tp2. use the GSM Hard-SPL: http://forum.xda-developers.com/showthread.php?t=550131
i hardslp the phone,everything went ok,can you tell my what rom should i put in it,which is the best,anyone that is english,which is the best?
also i saw here:
http://forum.xda-developers.com/showthread.php?t=550540
3. DOWNLOAD AND FLASH YOUR PREFERED ROM
and
4. FLASH PREFERED RADIO (OPTIONAL)
what is the difirence,what should i do?
thank you so much.
djole199 said:
i hardslp the phone,everything went ok,can you tell my what rom should i put in it,which is the best,anyone that is english,which is the best?
also i saw here:
http://forum.xda-developers.com/showthread.php?t=550540
3. DOWNLOAD AND FLASH YOUR PREFERED ROM
and
4. FLASH PREFERED RADIO (OPTIONAL)
what is the difirence,what should i do?
thank you so much.
Click to expand...
Click to collapse
The ROM is the Operating system part of the device. The radio is the part that controls all the radio functions lilke the GPS, cellular services, wifi, bluetooth, FM and such. It is not necessary to flash a new radio, but you could try any one of several English ROMs. Check the link in my signature for a listing of current ROMs for the Touch Pro2 (Rhodium).
ok,thank you,can you recomend me some rom,which is the best?
once again,thank you very much.
ciao.
I am having problem now with my htc,i can't sync it with pc,i have windows xp sp2,and i downloaded activesync 4.5,i conected phone with pc once and i hardspl the phone,but now when i am trying to sync it with my computer it won't recognize the phone,i was having trouble with syncing and the first time because the phone is on german language,i somehow conect it with pc,but now i can't,please help me.
thanks.
djole199 said:
I am having problem now with my htc,i can't sync it with pc,i have windows xp sp2,and i downloaded activesync 4.5,i conected phone with pc once and i hardspl the phone,but now when i am trying to sync it with my computer it won't recognize the phone,i was having trouble with syncing and the first time because the phone is on german language,i somehow conect it with pc,but now i can't,please help me.
thanks.
Click to expand...
Click to collapse
On your device, go to Start >Settings > Connections > USBtoPC. Uncheck the box that says "Enable faster data synchronization." Then plug it in to the PC and see if that works.
like i said phone is in german,i go to start,than i got einstllunget which is settings,i go there,i click mehr which is more than i've got verbindungen i beleive that is connections ther is usb zu pc,and there is for me to chose activesync mit outlook,als externe festplatte and internetfreigabe,down is for me to check and uncheck esrst nach usb-verbindungstyp fragen,wenn gerat mit pc verbunden wird,i can't find that that you said.
plesase help,maybe someone that speeks german,
thank in advice.
djole199 said:
like i said phone is in german,i go to start,than i got einstllunget which is settings,i go there,i click mehr which is more than i've got verbindungen i beleive that is connections ther is usb zu pc,and there is for me to chose activesync mit outlook,als externe festplatte and internetfreigabe,down is for me to check and uncheck esrst nach usb-verbindungstyp fragen,wenn gerat mit pc verbunden wird,i can't find that that you said.
plesase help,maybe someone that speeks german,
thank in advice.
Click to expand...
Click to collapse
In USBtoPC there is only one checkbox. The others are radio buttons. The checkbox should be under the radio button for ActiveSync. Make sure that box is unchecked and ActiveSync is the selected connection. After that, just tap OK and sync.
i tried that,it won't sync,can you recomend me something diffirent to try?
thanks.
can anybody help me,i tried diffirent cumputer which is on windows 7,i downloaded windows mobile device center but i still can't conect my phone,when i plug it on usb it only shows that it is charging and the red light starts in the upper part of the phone,but acivesync doesn't,can someone help me?
djole199 said:
can anybody help me,i tried diffirent cumputer which is on windows 7,i downloaded windows mobile device center but i still can't conect my phone,when i plug it on usb it only shows that it is charging and the red light starts in the upper part of the phone,but acivesync doesn't,can someone help me?
Click to expand...
Click to collapse
Try it on a PC with XP Pro x86 with the language pack installed. ActiveSync should immediately pick it up and connect.
a read somewhere that phone won't sync with pc because i use this kind of usb cable
http://www.toytowngermany.com/forum/uploads/monthly_08_2009/post-25516-12505295946685.jpg
not the original one,because i don't have one,but i will find one.
could that be it?i tried everything,active sync won't start on the phone when i connect it with pc.
djole199 said:
a read somewhere that phone won't sync with pc because i use this kind of usb cable
http://www.toytowngermany.com/forum/uploads/monthly_08_2009/post-25516-12505295946685.jpg
not the original one,because i don't have one,but i will find one.
could that be it?i tried everything,active sync won't start on the phone when i connect it with pc.
Click to expand...
Click to collapse
The original HTC cable is an eleven-pin miniUSB cable. I have only ever used the standard five-pin miniUSB cables like the picture you linked to since I got the device a year ago. In fact, I just built and flashed a ROM to it using that cable two days ago.
I'm not saying that that isn't your problem. Maybe it will work. I'm just saying that I have never needed it.
i don't know what else it could be,i connected the phone with pc once,and i hardslp the phone,then several days leter i conected it once again and active sync started i selected x beacuse i didn't need acivesync because i only wanted to charge the phone,tommorow i tried to connect phone with pc,i tried 100 times and i can't sync it,activesync won't start on phone when i plug usb cable in it,it only charges the phone.
djole199 said:
i don't know what else it could be,i connected the phone with pc once,and i hardslp the phone,then several days leter i conected it once again and active sync started i selected x beacuse i didn't need acivesync because i only wanted to charge the phone,tommorow i tried to connect phone with pc,i tried 100 times and i can't sync it,activesync won't start on phone when i plug usb cable in it,it only charges the phone.
Click to expand...
Click to collapse
If you already have Hard SPL, then you can flash ROMs directly from the SD card. If you flash a new ROM, it should restore your connection settings and allow you to start over.
thank you,that is so cool,yes i hardspl the phone,i will go and buy memory card,than i will install new rom,and radio.
thank you so much.
http://forum.xda-developers.com/showthread.php?t=550540
i found out here how to do it.
thanks once again.
The tool can hack the bootloader password from many devices e.g.:
HTC Blueangel
HTC Universal
HTC Himalaya
HTC Magician
HTC Harrier
HTC Alpine
and some more...
and with hacked password you can download or upload data from the device...
within the tool there is a little terminal like mtty...
So please test and give feedback...
Later this tool will be used to upload the new Linux kernel/bootloader for Android...
!!! WARNING !!!
If you don't know what you are exactly doing, you can brick your device!!!
FAQ:
- What is special on Vista/Win 7 32/64 bit!?
DOWNLOAD
VIEW CHANGELOG
05-02-2013
- Webupdate for Partitions
04-02-2013
- auto update function
02-02-2013
- gui like Windows 8
- add backup/restore function
- full Windows XP compatible
12-01-2013
- add Himalaya BL 1.01 (B-44)
02-11-2012
- add Magician partitions
- fix problem with partition bigger as 32MB
- more logging
- speed up upload e.g. 32MB from 10 to 4 min...
31-10-2012
- add logging mode
29-10-2012
- add Himalaya password for BL 1.03 (B-44)
- use timout and alternate commands for device name and bootloader...
reserve...
Another great work from you, d-two
I don't have Windows at the moment, so I can't test it, but I'm sure there aren't any serious bugs...
And just out of curiosity: What programming language did you use to make this?
Bootloader 2.07?
Can't open XML-File "devices".
Don't have a BA at hand, will come to play this afternoon.
O.K.-
WinXP, BA WM6.5.5Multilang, Bootloader v2.07
First forgot to disable USB-Connection in ActiveSync,
then connected properly.
Bootloader unlocked.
Flash/Download displayed like pic#2 in post#1.
tbc.
B-44 said:
Bootloader 2.07?
Can't open XML-File "devices".
Don't have a BA at hand, will come to play this afternoon.
Click to expand...
Click to collapse
What have you do?
have you extract the zip and start the exe or have you start it from zip file?
PS: Yes, my blueangel has the bootloader version 2.07...
you can use the Hima or Harrier too
miki100 said:
Another great work from you, d-two
I don't have Windows at the moment, so I can't test it, but I'm sure there aren't any serious bugs...
And just out of curiosity: What programming language did you use to make this?
Click to expand...
Click to collapse
I have use VB.Net...
d-two said:
What have you do?
have you extract the zip and start the exe or have you start it from zip file?
PS: Yes, my blueangel has the bootloader version 2.07...
you can use the Hima or Harrier too
Click to expand...
Click to collapse
What i've done?
Downloaded your file, copied it into a new folder & unzipped it.
Started exe and after connecting i can open "devices" in flash/download.
(I first was curious and tried to open it directly via right-click/open which didn't work.)
My Hima also likes your tool:fingers-crossed:
(Downloaded Himas bootloader just for testing.)
N:cyclops::cyclops:B question: is it also possible to upload .nbh files?
B-44 said:
What i've done?
Downloaded your file, copied it into a new folder & unzipped it.
Started exe and after connecting i can open "devices" in flash/download.
(I first was curious and tried to open it directly via right-click/open which didn't work.)
My Hima also likes your tool:fingers-crossed:
(Downloaded Himas bootloader just for testing.)
N:cyclops::cyclops:B question: is it also possible to upload .nbh files?
Click to expand...
Click to collapse
Nice idea i think i can add .nbh/.nbf support...
d-two said:
Nice idea i think i can add .nbh/.nbf support...
Click to expand...
Click to collapse
...as it unlocks bootloader...
edit 29.10.2012: here i was wrong.
As D-Two wrote: it unlocks BL-Password
and not BL itself, sorry.
nice tool
B-44 said:
...as it unlocks bootloader...
Click to expand...
Click to collapse
the bootloader is already unlocked but the nbf/nbh files need to be decoded ...
d-two said:
the bootloader is already unlocked but the nbf/nbh files need to be decoded ...
Click to expand...
Click to collapse
For the bootloader i'm impatiently waiting for a Hima i bought some days ago which hasn't yet experienced any one of your or other updates or unlocks... will first test your tool before doing anything else.
Just arrived- MDA2, supposed to be broken, but it is just the battery which is down to zero, so the phone doesn't start charging. Replaced.
Radio1.18.00 BL v1.03
Download mode, started your HTC_Flasher but in second step instead of "checking information of your device ... please wait" just a white bar appears, static.
Software is original T-mobile. Is there anything i can do before i start unlocking and upgrading?
(btw- i first didn't get it right, thought your tool wouldn't only hack BL password, but bootloader itself.)
MTTY Password for BL v1.06 didn't work (naturally?).
B-44 said:
Just arrived- MDA2, supposed to be broken, but it is just the battery which is down to zero, so the phone doesn't start charging. Replaced.
Radio1.18.00 BL v1.03
Download mode, started your HTC_Flasher but in second step instead of "checking information of your device ... please wait" just a white bar appears, static.
Software is original T-mobile. Is there anything i can do before i start unlocking and upgrading?
(btw- i first didn't get it right, thought your tool wouldn't only hack BL password, but bootloader itself.)
MTTY Password for BL v1.06 didn't work (naturally?).
Click to expand...
Click to collapse
OK, you have a Hima with BL 1.03 so we need the password for it!!
Make this:
Download this program
and install it on your pc...
then start it and select the stuff shown on the picture in the menu ...
after that start an update for the hima with the original updater and you can see the password...
Then send it to me...
That's why i asked... often older versions get lost because of people always update to "newest" version. That's why i call 1.2 of my EF82 the lost one- 1.3 has been registered just 16 hrs later, but now everyone updates to it, though it's worse. will take a look at bootloader... Update- which one, T-mobile or can i take Aeroflyluby's?
The bootloader Version will not updated ... never! You can update a wm6.5 Rom Form arofly.
O.K. just wanted to be shure not to spoil it.
edit: checked my BAs... Harriers all have v1.02 (think yours won't be different), one MDA3 v2.05, second one, italian Qtek2020 and Siemens SX66 v2.07
If you need PW of one of those just tell me, and i'll do as with Hima (tomorrow or monday).
d-two said:
The bootloader Version will not updated ... never! You can update a wm6.5 Rom Form arofly.
Click to expand...
Click to collapse
Here you are:
http://www.mediafire.com/file/pcyn08bc2xr2ybg/v1.03.dmswks
USB>password ~F0>~kv~a~~~~000
Pass1.
USB>
B-44 said:
Here you are:
http://www.mediafire.com/file/pcyn08bc2xr2ybg/v1.03.dmswks
USB>password ~F0>~kv~a~~~~000
Pass1.
USB>
Click to expand...
Click to collapse
ok i have add the password in the XML file please test it
thanks for help!!
PS: Blueangel, Universal and the other devices have a dynamic password only the Hima/Harrier use a static password for every bootloader version!
d-two said:
ok i have add the password in the XML file please test it
thanks for help!!
Click to expand...
Click to collapse
Negative- downloaded Flasher, unpacked it, Hima in bootloader mode, started Flasher
again gets hung in white bar
d-two said:
PS: Blueangel, Universal and the other devices have a dynamic password only the Hima/Harrier use a static password for every bootloader version!
Click to expand...
Click to collapse
So i only tell you if i find Hima or Alpine with a bootloader not yet listed.
hi bro
when I create my mi account i mess with one no. of mobile no. now my mobile was formatting and locked
i tried to contact mi company ..... rejected
tried download twrp , I can't coz it is locked
using fastboot mode and adb mode in cmd mode , also I can't coz it is locked
tried edl mode with test points , pc find the device but mi flash tools can't
fastboot with mi flash tools , also I can't coz it is locked
pleaaaaaaaaaaase help
muhanna123 said:
hi bro
when I create my mi account i mess with one no. of mobile no. now my mobile was formatting and locked
i tried to contact mi company ..... rejected
tried download twrp , I can't coz it is locked
using fastboot mode and adb mode in cmd mode , also I can't coz it is locked
tried edl mode with test points , pc find the device but mi flash tools can't
fastboot with mi flash tools , also I can't coz it is locked
pleaaaaaaaaaaase help
Click to expand...
Click to collapse
Hi there, there is just two way to solve this problem.
1. Contact with a Xiaomi Service Center. (They have their regulations to make sure that you are the owner of the phone)
2. Find someone that have Xiaomi EDL Authorized Account. (Most of them will ask for a turned off finding device feature, otherwise even they would not be able to help you)
If you are sure that your find device future is turned off, you can find someone in internet (at your own risk) that posses an EDL Authorized Account, or you can try websites like S-Unlock (also at your own risk) to get an EDL Authorized Account for yourself, it costs about 30$.
If "Find Device" option is turned on; either make a contact with Service Center again, or, I do Afraid, sell it as spare parts.
There is just one other way but it is highly risky: find someone that can change the chipset. (Hardware repair: not recommended)
If I were you I would double check if I still can get access to my mi account or not, maybe you can find some options to open it with some other credentials info.
Gesendet von meinem Redmi Note 9S mit Tapatalk
sz.hatef said:
Hi there, there is just two way to solve this problem.
1. Contact with a Xiaomi Service Center. (They have their regulations to make sure that you are the owner of the phone)
2. Find someone that have Xiaomi EDL Authorized Account. (Most of them will ask for a turned off finding device feature, otherwise even they would not be able to help you)
If you are sure that your find device future is turned off, you can find someone in internet (at your own risk) that posses an EDL Authorized Account, or you can try websites like S-Unlock (also at your own risk) to get an EDL Authorized Account for yourself, it costs about 30$.
If "Find Device" option is turned on; either make a contact with Service Center again, or, I do Afraid, sell it as spare parts.
There is just one other way but it is highly risky: find someone that can change the chipset. (Hardware repair: not recommended)
If I were you I would double check if I still can get access to my mi account or not, maybe you can find some options to open it with some other credentials info.
Gesendet von meinem Redmi Note 9S mit Tapatalk
Click to expand...
Click to collapse
1- my mi account is with my mobile no, but as u shown
if anybody call me from saudi arabia they start with 05xxxxxxx
but if they are calling from any country should start +9665xxxxxx
thats mean remove 0 from the the number
my mistake i put +9966 0 5xxxxxx for that I can't get the message of reset the password
I contact with the company they rejected my order and ask for me wifi which I use it for more than 5 years
2- my device is formatted so nothing I can do if finding device on it will be on and can't do anything
and something weird after formatting it is given me unlock code as shown and I tried and it was wrong
<img src="https://i.ibb.co/mRYZdRV/Whats-App-Image-2020-08-14-at-4-28-47-AM.jpg" alt="Whats-App-Image-2020-08-14-at-4-28-47-AM" border="0" />
I am going to try s -unlock and actually I start searching for chipset
thank u very much
muhanna123 said:
1- my mi account is with my mobile no, but as u shown
if anybody call me from saudi arabia they start with 05xxxxxxx
but if they are calling from any country should start +9665xxxxxx
thats mean remove 0 from the the number
my mistake i put +9966 0 5xxxxxx for that I can't get the message of reset the password
I contact with the company they rejected my order and ask for me wifi which I use it for more than 5 years
2- my device is formatted so nothing I can do if finding device on it will be on and can't do anything
and something weird after formatting it is given me unlock code as shown and I tried and it was wrong
<img src="https://i.ibb.co/mRYZdRV/Whats-App-Image-2020-08-14-at-4-28-47-AM.jpg" alt="Whats-App-Image-2020-08-14-at-4-28-47-AM" border="0" />
I am going to try s -unlock and actually I start searching for chipset
thank u very much
Click to expand...
Click to collapse
Maybe you can get an access to your mi account by mi website, try it out.
Gesendet von meinem Redmi Note 9S mit Tapatalk
there is official way at mi website where you will need to confirm it using your registered mi email account, they will reset the password for you