Hi,
From nothing my S4 mini stop working, but because i have some exp from old times i check if my computer recognize, and it appears Qualcomm HS-USB QDloader 9008 (After i install QUSB drivers). But the phone not enter in download mode or recovery mode, i tried many ways and look for all treads in the forum about that and nothing. Hope someone have any other idea.
Ps.: Already tried the card from debrick.img
azzurra01 said:
Hi,
From nothing my S4 mini stop working, but because i have some exp from old times i check if my computer recognize, and it appears Qualcomm HS-USB QDloader 9008 (After i install QUSB drivers). But the phone not enter in download mode or recovery mode, i tried many ways and look for all treads in the forum about that and nothing. Hope someone have any other idea.
Ps.: Already tried the card from debrick.img
Click to expand...
Click to collapse
Debrick image should bring it partially to life, how did you prepare for the sd card? Which debrick image did you use?
Related
Hello everyone.
I need your help.
My Device: LG G3 D855 32GB
The device does not turn on, the only thing that appears is because when I connect the device to a PC, I see a driver installed:
RELINK HS-USB QDLoader 9008
I read guides on site here, and I'm trying to order
I downloaded the software BoardDiag 2.9
I downloaded the files to the appropriate TOT
I extracted the files by instructors on site.
I opened the program and I followed the guide and it seems to me an error
Download mode is enabled Mode,
I quickly disconnects from the computer and reconnect the computer and then the moment I am unable to do a test and the results are:
AP CHECK START = PASS
EMMC TEST START
FAILED TO OPEN PARTITION FROM EMMC
TEST ABORTED !!
I tried a lot of tutorials but I can not, it always seems the device is in Download Mode
What can I do more?
Please your help,
Eliran
If you go that way, you will need bunch of other stuff. Here is the link
http://open-freax.fr/guide-unbrick-your-lg-g3/
It is a good thing that your PC recognises phone like that.
But first be sure that You can not enter download mode or recovery or even fastboot.
And please say what did you do to make it like that? Wrong flash?
If you CAN enter download mode than you can flash kdz or tot files from there. Easiest way is to use LGUP but you must be careful if you want to try.
The phone fell
Navuhodonosor said:
If you go that way, you will need bunch of other stuff. Here is the link
It is a good thing that your PC recognises phone like that.
But first be sure that You can not enter download mode or recovery or even fastboot.
And please say what did you do to make it like that? Wrong flash?
If you CAN enter download mode than you can flash kdz or tot files from there. Easiest way is to use LGUP but you must be careful if you want to try.
Click to expand...
Click to collapse
Thanks for the comment
The phone fell into the vehicle.
I know the phone is always in Download Mode
The software does not let me do anything and making phone download mode
I did not try to install KDZ.
And I can not open a setup KDZ because the device does not rise and there is no open port.
I only have the port I did above.
Thanks for the help, I worked in the guide and I could not ...
Navuhodonosor said:
If you go that way, you will need bunch of other stuff. Here is the link
It is a good thing that your PC recognises phone like that.
But first be sure that You can not enter download mode or recovery or even fastboot.
And please say what did you do to make it like that? Wrong flash?
If you CAN enter download mode than you can flash kdz or tot files from there. Easiest way is to use LGUP but you must be careful if you want to try.
Click to expand...
Click to collapse
Thanks for the help, I worked in the guide and I could not ...
I went through all the steps I found at:
Now, let’s get the party started
I set up the software the guide and I got an error:
FAIL on the EMMC test
I changed the parameter Read / Write »to« Erase
And again I got the error:
FAIL on the EMMC test
Then I try again, click Start, open a window and write in English and Chinese
Device DLOAD mode
device was not found in dload trying flash peogrammer
I click OK, the window closes and then when I press Start again, the window reappears.
Only when I disconnect the USB cable from the computer and the author briefly again then I’m able to do the test, but he failed.
FAIL on the EMMC test
The device always is in Download Mode and appears port:
RELINK HS-USB QDLoader 9008
My component can not be right at all and it always is in Download Mode?
I did not do short the guide, because the computer also detected me.
It has always seemed stuck in a download mode.
There is another option? Short elsewhere as will enable progress?
Thank you very much for your help,
Eliran
I need help please. What can i do
zarfati66 said:
Thanks for the help, I worked in the guide and I could not ...
I went through all the steps I found at:
Now, let’s get the party started
I set up the software the guide and I got an error:
FAIL on the EMMC test
I changed the parameter Read / Write »to« Erase
And again I got the error:
FAIL on the EMMC test
Then I try again, click Start, open a window and write in English and Chinese
Device DLOAD mode
device was not found in dload trying flash peogrammer
I click OK, the window closes and then when I press Start again, the window reappears.
Only when I disconnect the USB cable from the computer and the author briefly again then I’m able to do the test, but he failed.
FAIL on the EMMC test
The device always is in Download Mode and appears port:
RELINK HS-USB QDLoader 9008
My component can not be right at all and it always is in Download Mode?
I did not do short the guide, because the computer also detected me.
It has always seemed stuck in a download mode.
There is another option? Short elsewhere as will enable progress?
Thank you very much for your help,
Eliran
Click to expand...
Click to collapse
I need help please. What can i do
The phone woke for a moment ...
zarfati66 said:
I need help please. What can i do
Click to expand...
Click to collapse
Hello everyone
Today I tried again to connect the device to your computer, the screen comes on suddenly.
And see the state of battery with a question mark inside a yellow triangle.
I did not realize also saw installed driver
LGE AndroidNet USB Serial Port
I tried to re-install.
Now again became a black screen and the next thing happens:
When the device without a battery connected to a computer costing me
RELINK HS-USB QDLoader 9008
When I'm with a battery, it registers an unknown device.
When the device without a battery test again tried to do this EMMC component fails.
help please
Eliran
relink hs-USB Qdloader 9008
ZARFATI6 said:
Hello everyone
Today I tried again to connect the device to your computer, the screen comes on suddenly.
And see the state of battery with a question mark inside a yellow triangle.
I did not realize also saw installed driver
LGE AndroidNet USB Serial Port
I tried to re-install.
Now again became a black screen and the next thing happens:
When the device without a battery connected to a computer costing me
RELINK HS-USB QDLoader 9008
When I'm with a battery, it registers an unknown device.
When the device without a battery test again tried to do this EMMC component fails.
help please
Eliran
Click to expand...
Click to collapse
I am exactly in the same situation. Have you found any solution so far???? My phone suddenly stopped working and didn't boot up at all first and then I used the LG Flashtool to install original TOT file and all went well. I forgot to close LG Flashtool and it started flashing again. LG Flash tool restarts the phone at about 80% and then it failed at that point and since then I am having this issue.................
Any solution???????
apur32 said:
I am exactly in the same situation. Have you found any solution so far???? My phone suddenly stopped working and didn't boot up at all first and then I used the LG Flashtool to install original TOT file and all went well. I forgot to close LG Flashtool and it started flashing again. LG Flash tool restarts the phone at about 80% and then it failed at that point and since then I am having this issue.................
Any solution???????
Click to expand...
Click to collapse
Same situation too, solutions yet?
Hey I have the same problem .
If any of you found the solution please post it here or pm me, I am stuck
I have TOT files, I have BoardDiag (different versions), but when I follow the countless instructions online I always get "Device was not found in dload trying flash programmer.".
Where do I go from here?
Bro how are conecting your phone ..
If it is like ...
1: you installed the drivees for qualcome qhs bulk ..
2: device when conected now show under device manager as Qualcomm HS-USB QDLoader 9008
3:if above two are effermative tell me !! If not thwn again tell me...???
Check ure ports in d3vice manager
bravo2526 said:
Bro how are conecting your phone ..
If it is like ...
1: you installed the drivees for qualcome qhs bulk ..
2: device when conected now show under device manager as Qualcomm HS-USB QDLoader 9008
3:if above two are effermative tell me !! If not thwn again tell me...������
Click to expand...
Click to collapse
This is correct. I reinstalled the qualcomm driver, now it is COM3 and boarddiag from here works (http://open-freax.fr/guide-unbrick-your-lg-g3/), but emmc test fails.
"Failed to open partition from EMMC." It doesn't matter if I select Read/Write or Erase.
By the way, I didn't have to open my phone for the 9008 mode, it went there kind of on its own.
Quza said:
This is correct. I reinstalled the qualcomm driver, now it is COM3 and boarddiag from here works (http://open-freax.fr/guide-unbrick-your-lg-g3/), but emmc test fails.
"Failed to open partition from EMMC." It doesn't matter if I select Read/Write or Erase.
By the way, I didn't have to open my phone for the 9008 mode, it went there kind of on its own.
Click to expand...
Click to collapse
Bad news if emmc fails ..i supose its a hardware damage to your emmc chip ...
What was you trying when it happend ..?
Power outage during rom installation ??
During KDC flash it stopped working. After 15 minutes at 0% I restarted the phone.
Hey I was flashing downgrade to fix issue with my Wifi Mac but its its not happened instead my phone got hard bricked after I am pretty sure I have valid version of flash zip (from google) 6.0.1 last. but its got hard brick anyway! so After a lot searching I find this article:
http://www.droidsavvy.com/unbrick-qualcomm-mobiles/
but when I follow this article first time its failed so I reconnect my phone after plug and I didn't see that pc detect my phone at all! normally its show Qualcomm HS-USB QDLoader 9008 (Port COM6) but now nothing.
Please help me out!
Anyone?
I attempted to flash Dirty Unicorn from they're site, which appeared to go well, then I proceeded to flash the TWRPinstaller.zip that was suggested from the maintainer for our device. when I tried to reboot from recovery I got a no OS message. I ignored the message and attempted to reboot. Now the phone doesn't normally power on or off(which may change once the battery dies), no boot animation, no recovery, no fastboot recognition. The computer recognizes the phone as Qualcomm HS-USB QDLoader 9008. I googled for hours last night trying to fix to no avail. Has any of our great devs found a way to atleast recover the bootloader screen. I think I can handle it myself from there with adb.
Solved: Use the first blank flash from the link to get back to bootloader screenhttps://firmware.center/firmware/Motorola/Moto%20Z2%20Force/Blankflash/
From bootloaderscreen put your ADB skills to work. I'm not too good with guides but this just saved me $175
mookiexl said:
I attempted to flash Dirty Unicorn from they're site, which appeared to go well, then I proceeded to flash the TWRPinstaller.zip that was suggested from the maintainer for our device. when I tried to reboot from recovery I got a no OS message. I ignored the message and attempted to reboot. Now the phone doesn't normally power on or off(which may change once the battery dies), no boot animation, no recovery, no fastboot recognition. The computer recognizes the phone as Qualcomm HS-USB QDLoader 9008. I googled for hours last night trying to fix to no avail. Has any of our great devs found a way to atleast recover the bootloader screen. I think I can handle it myself from there with adb.
Click to expand...
Click to collapse
I did the same, got the same. Can't confirm the Qualcomm HS-USB QDLoader 9008 device will be there.
No charge, no screen, does not turn on/off, no vibration. Worst: no bootloader... Again, could be different if the battery dies.
mookiexl said:
Solved: Use the first blank flash to from the link to get back to bootloader screenhttps://firmware.center/firmware/Motorola/Moto%20Z2%20Force/Blankflash/
From bootloaderscreen put your ADB skills to work. I'm not too good with guides but this just saved me $175
Click to expand...
Click to collapse
Three questions:
1. File there is NDX26.183-15_17. Is it the same for OPXS27.109-34-10 on which I'm now? I suppose I need to use the "Oreo" version (2nd file in the list).
2. Which tool/software did you use to flash it? Is there a step by step tutorial?
3. You say "from bootloader screen". What about if we do not have a bootloader screen but a black brick in our hands?
Technical said:
I did the same, got the same. Can't confirm the Qualcomm HS-USB QDLoader 9008 device will be there.
No charge, no screen, does not turn on/off, no vibration. Worst: no bootloader... Again, could be different if the battery dies.
Three questions:
1. File there is NDX26.183-15_17. Is it the same for OPXS27.109-34-10 on which I'm now? I suppose I need to use the "Oreo" version (2nd file in the list).
2. Which tool/software did you use to flash it? Is there a step by step tutorial?
3. You say "from bootloader screen". What about if we do not have a bootloader screen but a black brick in our hands?
Click to expand...
Click to collapse
Answers
1.NDX26.183-15_17 (All it does is get your boatloader screen back
2. If you go to the device menu on your computer and your phone reads as Qualcomm HS-USB QDLoader 9008, all you have to do is click on the Blank flash all file and from the extracted folder and command prompt will do the rest. If the device is not recognized QDLoader 9008 then you will need to download qualcomm drivers to your computer
3.That is exactly what the file is for. Getting your black brick to at least the bootloader screen. From there you can adb recovery or stock rom.
What I ended up doing was adb push the bootable TWRP from the this thread https://forum.xda-developers.com/z2-force/development/how-to-install-oreo-ota-t3726932.
Flash the TWRP the official for our device from they're site(the bootable TWRP will give you access to extsd and thats where I had the official TWRP )
Rebooted back to bootloader and adb the firmware files for my device from the AOISP thread and rebooted my phone and I was booting DU.
Can somebody help me? I am in the same situation.
T-Mobile, unlock bootloader, hard bricked (already recognized Qualcomm QDLoader 9008 in device manager at least...)
I tried to use the blankflash but...see attachment
Dany XP said:
Can somebody help me? I am in the same situation.
T-Mobile, unlock bootloader, hard bricked (already recognized Qualcomm QDLoader 9008 in device manager at least...)
I tried to use the blankflash but...see attachment
Click to expand...
Click to collapse
Before connecting the phone, start the blankflash program. Maybe you have to repeat it a couple of times. Also try different cables, ports and computers.
Dany XP said:
Can somebody help me? I am in the same situation.
T-Mobile, unlock bootloader, hard bricked (already recognized Qualcomm QDLoader 9008 in device manager at least...)
I tried to use the blankflash but...see attachment
Click to expand...
Click to collapse
https://forum.xda-developers.com/showpost.php?p=77623934&postcount=5
mookiexl said:
Answers
1.NDX26.183-15_17 (All it does is get your boatloader screen back
2. If you go to the device menu on your computer and your phone reads as Qualcomm HS-USB QDLoader 9008, all you have to do is click on the Blank flash all file and from the extracted folder and command prompt will do the rest. If the device is not recognized QDLoader 9008 then you will need to download qualcomm drivers to your computer
3.That is exactly what the file is for. Getting your black brick to at least the bootloader screen. From there you can adb recovery or stock rom.
What I ended up doing was adb push the bootable TWRP from the this thread https://forum.xda-developers.com/z2-force/development/how-to-install-oreo-ota-t3726932.
Flash the TWRP the official for our device from they're site(the bootable TWRP will give you access to extsd and thats where I had the official TWRP )
Rebooted back to bootloader and adb the firmware files for my device from the AOISP thread and rebooted my phone and I was booting DU.
Click to expand...
Click to collapse
Can somebody please help me, my laptop isn't even detecting my device as QDLoader 9008, can you please tell me which windows os version did you use, also did you use the usb cable came in the box and did you use usb 2.0 port or 3.0?
LØNEWØLF said:
Can somebody please help me, my laptop isn't even detecting my device as QDLoader 9008, can you please tell me which windows os version did you use, also did you use the usb cable came in the box and did you use usb 2.0 port or 3.0?
Click to expand...
Click to collapse
Well, you need of course, Qualcomm loader driver, to at least having your device recognized as 9008. There u go: https://www.androidbrick.com/download/latest-2017-qualcomm-diag-qd-loader-windows-10-drivers-signed/
After that, go ahead with blankall and stuff...
P.s. and yes ..stay away from USB 3.0! ???
Dany XP said:
Well, you need of course, Qualcomm loader driver, to at least having your device recognized as 9008. There u go:
After that, go ahead with blankall and stuff...
P.s. and yes ..stay away from USB 3.0!
Click to expand...
Click to collapse
Thanks for the reply bro....but I have that driver installed...I installed before connecting it....still not detecting... I'm gonna try this once more in my friend's pc... let's see what happens
LØNEWØLF said:
Thanks for the reply bro....but I have that driver installed...I installed before connecting it....still not detecting... I'm gonna try this once more in my friend's pc... let's see what happens
Click to expand...
Click to collapse
I know it's a long shot but...do u have any other Qualcomm device to try?
U can enter EDL mode with adb command "adb reboot edl". Yes, it's that simple. ?
Dany XP said:
I know it's a long shot but...do u have any other Qualcomm device to try?
U can enter EDL mode with adb command "adb reboot edl". Yes, it's that simple. ?
Click to expand...
Click to collapse
OK I'll try...but how would I get back from edl to Normal without doing anything in the edl?
LØNEWØLF said:
OK I'll try...but how would I get back from edl to Normal without doing anything in the edl?
Click to expand...
Click to collapse
Uh...good question
Upgrade:
I need some files to run QFIL:
prog_emmc_firehose_8996.mbn (.elf)
rawprogram0.xml
patch0.xml
https://forum.xda-developers.com/ha...e-progemmcfirehose8996-mbn-elf-qfil-t3867750/
---------------------
Brick black screen Qualcomm HS-USB QDLoader 9008 (COM20). I need help please
Please, I need a lot of help. I will give you all the details I can.
I have always used the following ROM:
G891AUCS2API2_CL8737252_QB10881022_REV02_user_low_ship_MULTI_CERT
I have never had problems with this ROM. I wanted to try the AT & T ROM pirmera (it's an official ROM) and I installed it with modified Odin3 3.12. I have always used this Odin without problem. The ROM that has generated the problem is this:
SM-G891A_G891AUCU1APG7_ATT_Full_Repair_Frimware
I installed it with the same options as ROM REV02, so the problem is not Odin's. I think the problem is having downloaded Android version.
When I installed the ATT_Full_Repair_Frimware ROM, Odin said there was success. However, the phone did not turn on.
I tried to charge the phone, without success. Neither does any combination of buttons work.
When I connected the mobile to the computer, a driver was installed:
Qualcomm HS-USB QDLoader 9008 (COM20)
I also think that I read something from QFIL.
This is the only thing I have achieved. Odin does not work in this mode. I'm finding some weird Internet programs:
qpst.win_.2.7_installer_00472.4
Qualcomm Premium Tool V2.4 cracked + WORKING KEYGEN
This is a very difficult case for me and the people in my group of computer friends do not have the ability to solve this problem either. Only XDA can help me.
@NotSoMiniGun, please.
@Slade8525, please.
@activefan01, please.