:?
I tried to make an update with the file JASJAR_WWE_11353_137_10301
Suddenly the Display stop et 99% of the extended Rom Update and on my monitor was an infomation like "an error happend"
After this, nothing else happend .
Yes, realy nothing happens anymore. I cant start the device not with power, not with reset or with power+reset
nothing nothing nothing
What can i do
If i start to try a new update, it schows me no information about what rom etc. is installed or what will be installed. if i then start i get the notice, that it is the wrong device.
Help me please. ist there any way to put the mda back to live?????
I guess i dont only need an update but the complete software
HELP!!!
I have the exact same issue after the upgrade. Nothing will happen. I spent several hours trying resets, combination of button pressed, removed battery, resets, just to try to get back the boot loader mode but nothing is happening.
there has to be a way to do this and I hope someone on this board had that issue before and got it resolved.
I had a similair issue with my old XDA II, it turned out my storage card was corrupted. Use a card reader to check your storage card is OK, perhaps format the storage card (having saved any data first of course) and see how you fare
Have had the same problem wirh a radio ROM update on my QTEK9000. The anly thin that still worked was the hard reset. After the hard reset the device still did not respond. But when i connected it to the PC I could start the updateprocess of the original ROM. I took about 20 minutes for the whole procedure and than the Qtek9000 was back in factory default (Pffff and I could breath again).
So perhaps you can try a hard rest and then connect aganin to the PC.
I allready tried this!
But nothing happens.
Even if i put the power device or the usb into the mda, no LED schows anything. just sometimes the LED is red for not more than a minute. if it then goes out, i get the message "Unknown usb device" in my PC
Are you in bootloeader mode? Do you see the words USB or Serial on the screen of the Universal in Portrait mode. Note: Backlight is off so you have too look real hard, but it should be there
no, i see nothing.
I had quite a hard time yesterday while upgrading. The bootloader is very hard to see, use a torch to lite up your display. In portrait view on the top should be the word serial or usb, on the bottom v1.00.
I also did a hard-reset in this stage, but it just returned to the bootloader menue.
If I connect to the PC and the device is recognized I see the word serial in the display change to USB. For me I do not know the reason but my PC did not want to fulfill the upgrade process. Needed to take another PC (Laptop) to solve the problem. After the upgrade of the ROM, You still need to upgrade the Radio (this was my experience) before a cold-reset will put You back to business.
Good luck.
Ruud
Having the exact same problem as gary_b and having performed quite a few upgrades, I can confirm there is absolutlely nothing on the screen. The unit will not go into bootloader mode or even able to do a hard reset. It is not recognized when plugged in the USB.
When connected to power and the hard reset procedure is done, the red charging light will come up for less than 1/2 seconds and disappear.
I tried all different combination to make it boot but nothing. If I could at least get it to bootloader more, I can revive it.
Feel very bad I cannot help here.
I was wondering Yesterday about one thing. IF, during all this upgrading process, the battery runs out, (as it does not seem to charge during upgrade process) will it show bootloader screen ?
Would it be possible to get a loaded battery from somebody to check yours ?
That is a good suggestion to try out, but I have been unable to find anyone that has that device. It might be simply a drained battery.
Mine got corrupted I think at the end of the upgrade right after I did a regular reset instead of teh power and reset procedure.
However, I would think that even with no battery in, the unit should power back up when plugged in no?
Maybe an idea for somebody who is doing upgrading now, and is in bootloader status anyway.
Take out the battery, but connect with USB to PC with ASync. Does the bootloader state show ?
I am sorry to not do it for myself, if You saw my desperate state Yesterday, You will believe that I am not willing to see that bootloader screen for some time, sorry.
Ruud
now i know what to do:
Nothing!!
I went to a service-point with my mda pro and there was nothing to do with it.
If this happens the complete memory is "killed". Like "format c:" and while format is running you switch out the power.
Thanks god: I got a new MDA pro because i did not tell them (in the store)that i tried an update!
But i called the service-line before anf they told me that there is nothing to do!
But thx
Wow, can't say that this is good informatuin for those with this problem, but very glad it worked out for You.
I ve had this problem 5 minutes ago. Finally a took out the battery. Then connect to AC and Red led is on. Then i put the battery, tried hard reset and message to confirm hard reset in the screen (wellcome to life, jasjar).Then i run radio update again and it's upgrading rigth now....buffffff
I almost suffered a heart attack when this happened an hour ago. Have found that the update works fine if the SD card is taken out... phew.
heloo
I am currently upgrading my XDAIIs from WM2003 to WM6.5.
after checking the system from my XDAIIs, suddenly the power led went off and the sync is disconnected so I cannot continue the upgrade. On my phone screen there are only gray screen with USB at the top and V.2.07 at the bottom.
I have tried to restart the upgrading process but the problem is now my phone cannot connected to my laptop although I am using USB. I also tried to change the usb port and sync with other computer, but the problem is still the same.
FYI : at the beginning of the upgrade process, I didn't hard reset the phone. Is this the cause of the problem??
Please help me, does anyone have any solutions?
your device is in bootloader mode and it should show up as a ms_wm_device in
windows and you should be able to flash it again you can read more here
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel
chanxda... you sorted it yet! I had same problem last nite and figured it out. Ill watch thread if you need reply!
Hello All,
I have a HTC Incredible and it keeps rebooting. I turn it off and when i turn it back on it shows the white screen with "HTC Incredible" and buzzes for half a second and reboots. It does this forever until i take the battery out. I can go to HBoot and any option i choose it restarts the phone and the same thing happens again. When i plug it in my computer, it does not show up anywhere because it keeps rebooting. the only way that i can make it recognized on computer is by leaving it on HBoot screen and then plugin it in my computer, even then, my computer says that the device driver was not installed successfully.
see this video i made: watch?v=x4VAfUuhP98
I'm noob so please explain to me in as plain english as possible on how to fix this. If you could provide me a step by step process, i'd really appreciate it.
thanks in advance.
Good morning, I have a big problem in my Zenfone 2 and would very much like your help.
Yesterday in the morning he hung up, I thought I had downloaded but I tried to turn it when he called saw the battery was at 50%, I found strange but ok, then the screen locked and the phone started to vibrate and I had to off it. When I called, the battery was at 50%, was saying that the phone was connected and there do not leave sound and saying he was carrying. I thought it might be the rom and turned it on PC to back up and exchange of rom, only the USB no longer recognized the connection to the PC. Was saying that tava carrying, I took the USB and stopped "load" when I called he carried again, just not giving connection to the PC. Anyway I did not back up and changed the rom, he continued the same thing (I was in the AICP (LP) and put the RussiaNBear (LP)).
So I was following a tutorial that I had used before to repair another error (I could not post the tutorial link here, but it's on youtube: (Tutorial - Zenfone 2 unbrick / Restore (ZE551ML / ZE550ML) - In the Droid Will channel)), but I gave soft to do so because the part of the AFT (Asus Flash Tools) it does not recognize the phone, having to disconnect the usb and connect again, and then I screwed me, 'cause the uSB connection was not working. After a few unsuccessful attempts, it seems I agravei even more the situation because now I turn the USB cable pressing volume down and it goes in "Moorefield" and the PC identifies a good, open the xFSTK and can pass the DNX, but when you finish spending DNX the phone should reboot and a screen appears with the symbol of a uSB connection, but that's not what happens. I spend the DNX, the phone restarts and vibrates, there is the xFSTK waiting to pass the OS, but not USB screen appears, the xFSTK does not recognize the phone more in "Moorefield" and I can not do anything else on the device.
I have already connected the phone on another pc, I have changed the cable and nothing. I think it is the mobile usb, if not it would not recognize the first part of xFSTK.
Apologies if I have not posted in the right place, for my English (Google Translate) and the text size, only tried to leave everything well explained so that everyone can understand. Thank you very much, beforehand to help you and I really hope we can solve this problem.
Thank you.
No one ?
no one can help me?
I've got a dead oneplus 5t from my son. It was not charging anymore.. So I've replaced charging cable and battery.. Seemed to work it was charging... However it doesn't boot... No logo screen screen stays black/blank.
Tried several suggestions on this forum to get into recovery mode, fastboot mode... But still nothing. Only vibrating works after a few seconds.
So tried to unbrick with OP5T_Unbrick_tool_dumpling_43_J.40_181105(OOS.5.1.7) and the qualcomdrivers..
I was able to install the drivers and I see they are installed in devicemanagement.. and an empty folder create for oneplus.
I charged the phone all night and was able to download the upgrade. It then says download complete and I tried to restart the phone..
Still just vibrating but nothing happens.. Seems like everything has vanished from the phone, no recovery, no bootloader, no files.
So how to proceed to get all the stuff on the phone? And maybe the displayscreen is dead, but how can I tell?
Also tried the SMT upgrade. Strange thing is the device and com port are seen in devicemanagement and active when I connect without volume up, but cannot start because it says When I try to use smt mode the program says: "This COM port is disable by user". With volume button up pressed and then connect, ledlight turns green but the qualcomdevice is grayed out in devicemanagement and it says waiting for device..
Any help is welcome. I am a noob in how to proceed on the phone however I have an IT background.
Spent already so many time figuring out .. maybe it's effortless and its for the trashbin.
Thanks in advance
SOLVED
I opened the phone again loosened all those tiny connections to battery, screen,charger, mainboard and re-attached them.. Somehow a connection seemed to be fitting allright as yI looked at it, but apparently wasn't :good: