I have a Note 8.0 that is stuck in a boot loop. It get to the initial screen. "Samsung Galaxy Note 8.0 GT-N5110" and then screen goes blank and it starts over again. Never goes past this screen. I have flashed a stock rom (\N5110UEU2COI3_N5110XAR2COI3_HOME.tar.md5) using odin. Odin gives me a pass when it is finished but the issue persists.
Any help with this is appreciated.
Re-flash the stock ROM but, before booting for the first time, boot into stock recovery and do a full wipe. This may help get out of the bootloop.
audit13, thanks for the suggestion. I tried 3 times with no success. I did see the android with his belly door opened and the blue box spinning. Didn't see that before. However when I boot into recovery the android's belly door has a red triangle in it. A full wipe/reset has no effect and the symptoms persist.
Any other thoughts? Thanks again
I recommend trying again with Odin 3.07.
In Odin, uncheck everything except f.reset time. Connect the tablet in download mode, flash the tar.md5 file in PDA. When you see the word "Reset" in the status window, remove USB cable, press and hold the power button to power off the unit. After the unit is off, use the key combination to boot immediately into recovery and perform a factory wipe/reset. If that doesn't work, you may need to flash the ROM in combination with a pit file.
audit13, tried your instructions and still ended up with the same issue. I used odin3 v3.07. Can you point me to the pit file you referred to in your previous post.
I have this file - BL_N5110UEU2CNE2_1498778_REV01_user_low_ship.tar.md5
and this - CSC_XAR_N5110XAR2CNE2_1498778_REV01_user_low_ship.tar.md5
Are they of any use to me in this situation?
Thanks again for taking an interest in my problem, Keith
Did you download the stock ROM from sammobile? If you did, you should unzip the file once which gives you a tar.md5 file. It is this tar.md5 that is flashed in the PDA section of Odin 3.07.
SamMobile has many countries listed but not USA. Do I use Cellular South? The file I have been trying was not from SamMobile.
When you boot into download mode, does it give you the model #? Do you see anything about Knox or warranty bit in download mode?
The firmware named in the original post looks like it matches Cellular South.
I'm not sure if the 5110 was sold in the USA. If your model is wifi only, another country may work. If it's celluar, different countries use different frequencies which means cross flashing may work but connectivity (wifi and cellular) may not work.
Download mode shows this:
Odin mode (in red)
Product name: GT-N5110
Current binary: Samsung Official
System status: Custom
Knox Warranty Void: 0
RP SWREV: A2
It's strange that you were able to flash a stock ROM but the system status is "custom".
I suggest trying to flash an entire ROM from sammobile.com similar to the BL and CSC you flashed earlier. It may be simplet to install a custom recovery and flash a custom ROM so you can at least confirm the baseband and bootloader currently installed.
I'll give a custom recovery and rom a try tonight after work. TWRP and any stable build correct?
As for those two separate files, I didn't try anything with them. I downloaded them in case I needed to use them.
This is a board that I got off eBay for $5 and I don't know it's history. Could this issue be hardware related? The board looks good with no signs of corrosion (water damage) of hot spots (electrical surge).
It seems as though it can't find the os on boot.
Thanks again.
Did the board ever boot or was it stuck in a bootloop from the beginning? How did you know which bootloader to flash?
The board has never booted. The only files I have flashed are the one in my first post and the one from SamMobile (Cellular South) as per your instructions. These two files appear to be one in the same. Both files when flashed produced the same result, boot loop.
Do the files contain a boot loader? It sure feels like that is where the problem lies.
Success! Flashed TWRP and then installed SlimKat 4.4.4 and all is working. Need to get gapps installed but for now this board is good.
audit13, thanks again for you interest in my issue.
Related
Galaxy note 2 I317M can’t flash, stuck on Samsung galaxy logo
On this one can’t flash anything
With Odin gave error on modem partition (when start to flash). I can flash the recovery partition
With any box on sboot partition
I can go in download mode but CAN’T go in recovery mode, stuck in Samsung galaxy logo
I don’t know anything about the history
Is supposed to be a phone with cracked LCD but after replaced I’m stuck
Thanks for any ideas
P.S
please don't ask me to wipe or entry in recovery mode because the phone is not able, just in download mode
thanks again
Did the device boot up correctly after you received it?
about getting into recovery, just flash one with odin in download mode and see if you can get into it (home + power + volume up (or down, can't remember which of the 2 are for download mode, haven't used it in ages) ) I would recommend TWRP, as that one has a file manager in it you could use to see if there's anything on the device already.
make sure you get the official rom for your device
Code:
sammobile.com
most likely has what you need, downloads are slow though and you need to register but its a good site nevertheless.
make sure the file of the rom isn't corrupted, do a md5 check before you try to flash it. After downloading the rom zip file you need to extract it and point odin to the tar file with the "PDA" button, do not select anything besides "Auto Reboot" and "F. Reset Time" (they should be selected when opening ODIN, leave the other setting checked off)
What settings did you use in odin if i may ask? if you choose to repartition or erase nand or whatever they call it in the newer versions, you might have a serious issue as you have to have a special PIT file to get the partitions back. It also would explain why odin can't flash to the boot partition as its simply not available. If i'm not mistaken the PIT file for our devices isn't available.
could you perhaps explain a bit more in detail what steps you took after you got the device/replaced the screen in combination with odin and such? If you can't flash recovery or a rom through odin, then my best bet would be your device is ready to be thrown in the garbage.
i have the same prob once, and solved it...
here's what i did.
-reflash stock rom via odin
-reboot (boot loop acheived!)
-flash TWRP
-wipe cache/dalvik
-reboot but this time stuck at sammy logo for a while...
i left it alone for a while, about 15 mins. came back, and saw i was at the initial setup screen. try it... it may work for you too.
msk514 said:
i have the same prob once, and solved it...
here's what i did.
-reflash stock rom via odin
-reboot (boot loop acheived!)
-flash TWRP
-wipe cache/dalvik
-reboot but this time stuck at sammy logo for a while...
i left it alone for a while, about 15 mins. came back, and saw i was at the initial setup screen. try it... it may work for you too.
Click to expand...
Click to collapse
he tried flashing with odin though, but he got an error while flashing about the modem partition, either something is broken inside the phone,(missing partitions due to wrong wipe in odin perhaps) or the rom he downloaded is corrupted. Also he seems to have issues with the recovery being unable to be flashed to the device.
as soon as you get the samsung boot logo (not the initial galaxy one where your device model is mentioned) the rom is booting up, first time always takes a while being stuck on the galaxy logo however means there's probably not any boot partition written with a boot.img by odin This could also mean either corrupted rom file or lack of partition to write too. No boot partition means the device simply doesn't know it should load something.
If i understand his post correctly he bought a second-hand device where only the screen was broken. i don't know how the screen got broken in the first place, but if the device took a hard fall, there's a big chance its not only the screen but also some hardware got broken.
i have more details
actualy is a AT&T version (someone changed the screen from a canadian phone but forgot to change the label
I'm able to flash the AT&T rom I317ATTALJ2 from sammobile with odin 9reboot and F. reset time checked) but is stuck on samsung galaxy note 2 logo
I CAN"T entry in recovery mode (don't know why)
only download mode
contramundi said:
If i understand his post correctly he bought a second-hand device where only the screen was broken. i don't know how the screen got broken in the first place, but if the device took a hard fall, there's a big chance its not only the screen but also some hardware got broken.
Click to expand...
Click to collapse
i bought the phone with cracked screen
after tried many times i asked the owner and he told me the label is from a Canadian phone but the motherboard is from at&t
i can flash ONLY with odin and only I317UCALJ2 firmware. Any other firmware from at&t or not i have error when flash the system partition
i tried also with Octopus Box and Z3x Box. Same error
after flash successfully with odin is stuck in Samsung logo and NO RECOVERY MODE
so don't ask me to wipe
maybe with some Linux commands?
thanks
Sounds like you need the pit file and re partition checked i would look for a pit file for your phone when you find one check repartition
32dave said:
Sounds like you need the pit file and re partition checked i would look for a pit file for your phone when you find one check repartition
Click to expand...
Click to collapse
can't find pit file
i don't know if is the same like i317m or n7105
even like this i think i need a rom with modem, csc, pda and bootloader separated
thanks
nickmatine said:
can't find pit file
i don't know if is the same like i317m or n7105
even like this i think i need a rom with modem, csc, pda and bootloader separated
thanks
Click to expand...
Click to collapse
try to flash http://forum.xda-developers.com/showthread.php?p=37688128 or if you have a different model than 7105 do a google search for a pit file for that phone.
afterwards flash the stock rom for your model (att/tmobile/etc) the rom itself should contain everything you need.
Found a pit file i will upload it here but it is from this thread http://forum.xda-developers.com/showthread.php?t=2376405 hope this helps
32dave said:
Found a pit file i will upload it here but it is from this thread http://forum.xda-developers.com/showthread.php?t=2376405 hope this helps
Click to expand...
Click to collapse
seeing as the motherboard is from AT&T should he still use the canadian PIT file?
(don't wanna sound like a noob, and don't have the slightest clue about how the hardware inside the phone actually works so i'm just trying to learn new stuff )
I don't think it makes a difference as far as the pit goes
just let you know i was able to flash a stock rom from at&T and the phone work well now
thanks to everybody:good:
I cannot get my phone to boot up. It loads the splash screen and gets stuck there. It doesn't move past that screen. I've tried multiple times going into recovery mode but it won't go. I can get into download mode though. I've tried using Odin 3.07 to reflash the KIES_HOME_I317UCALJ2_I317ATTALJ2_215287_REV04_user_low_ship.tar.md5 from the back to stock rar I found here http://forum.xda-developers.com/showthread.php?p=41340941 and I do not know what to do next. I've even tried flashing a recovery tar file I found here http://forum.xda-developers.com/showthread.php?t=2533333. I've also tried removing the battery, replacing the battery (I have a second battery), and even if I power off the device and plug it up to my charger it loads the splash screen and stays there. I've looked around online and found this http://www.note2forum.com/forum/galaxy-note-2-help/1530-troubleshooting-samsung-galaxy-phone-bootloop.html#post20381 but can't even get to recovery mode to do a data wipe. The last thing I was able to do successfully with my phone was get it back to stock so and do the update to 4.1.2 because it was on 4.1.1 and I've seen something called SDS while searching. Is that what happened here? Is my phone able to be repaired? When I'm in download mode the upper left corner shows the following information:
ODIN MODE
PRODUCT NAME: SGH-I317
CUSTOM BINARY DOWNLOAD: Yes (3 counts)
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
KNOX WARRANTY VOID: 1
RP SWREV
I'm doing some serious reaching here because this is my primary phone, and I'm not familiar with PIT files but what I briefly read stated something about identifying which files go to which partition. I have no experience or knowledge of bootloader functions/changes and I've never checked more than auto reboot and reset time in ODIN. Any help is greatly appreciated.
Update!!! OMG I'm so happy to make progress. I flashed in ODIN the 4.3param_tz.tar file found herehttp://forum.xda-developers.com/showthread.php?t=2497994 and it successfully rebooted me into CWM. I will post the results of a ROM restore I'm attempting shortly. I was able to complete a full restore of a previous ROM and my phone is now currently booting up as I type this. Hopefully nothing goes wrong, but I've gotten farther now than I have in the past 5 hours I've been glued to my laptop. Time for a cig and beer.
Assassyn said:
I cannot get my phone to boot up. It loads the splash screen and gets stuck there. It doesn't move past that screen. I've tried multiple times going into recovery mode but it won't go. I can get into download mode though. I've tried using Odin 3.07 to reflash the KIES_HOME_I317UCALJ2_I317ATTALJ2_215287_REV04_user_low_ship.tar.md5 from the back to stock rar I found here http://forum.xda-developers.com/showthread.php?p=41340941 and I do not know what to do next. I've even tried flashing a recovery tar file I found here http://forum.xda-developers.com/showthread.php?t=2533333. I've also tried removing the battery, replacing the battery (I have a second battery), and even if I power off the device and plug it up to my charger it loads the splash screen and stays there. I've looked around online and found this http://www.note2forum.com/forum/gal...-samsung-galaxy-phone-bootloop.html#post20381 but can't even get to recovery mode to do a data wipe. The last thing I was able to do successfully with my phone was get it back to stock so and do the update to 4.1.2 because it was on 4.1.1 and I've seen something called SDS while searching. Is that what happened here? Is my phone able to be repaired? When I'm in download mode the upper left corner shows the following information:
ODIN MODE
PRODUCT NAME: SGH-I317
CUSTOM BINARY DOWNLOAD: Yes (3 counts)
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
KNOX WARRANTY VOID: 1
RP SWREV
I'm doing some serious reaching here because this is my primary phone, and I'm not familiar with PIT files but what I briefly read stated something about identifying which files go to which partition. I have no experience or knowledge of bootloader functions/changes and I've never checked more than auto reboot and reset time in ODIN. Any help is greatly appreciated.
Update!!! OMG I'm so happy to make progress. I flashed in ODIN the 4.3param_tz.tar file found herehttp://forum.xda-developers.com/showthread.php?t=2497994 and it successfully rebooted me into CWM. I will post the results of a ROM restore I'm attempting shortly. I was able to complete a full restore of a previous ROM and my phone is now currently booting up as I type this. Hopefully nothing goes wrong, but I've gotten farther now than I have in the past 5 hours I've been glued to my laptop. Time for a cig and beer.
Click to expand...
Click to collapse
Good for you! FYI, I think u can do a wipe through adb (adb wipe) I think. Nothing should go wrong after restoring your nandroid. (BTW, it's not sds.)
P.S. get a good beer and relax.
Smack that thanks button if I helped!
Note 2 LTE powered by Illusion ROM and Plasma Kernel.
Sent from dat small country called Singapore.
P.S. replies with quotes will be replied to faster.
Sadly ...we still can't dump that pathetic Knox bootloader ...yet...but progress is being made...
And if not...we can downgrade and still flash any rom we want...g
Sent from my SAMSUNG-SGH-I317 using XDA Premium 4 mobile app
Hi, so I recently rooted, flashed TWRP, and put SlimKat on my phone, and it worked great for a few days, but then all of a sudden it would freeze on the lockscreen. To fix this I would need to pull out the battery or do the hard reboot. Then, today, after doing that once again, when I tried to boot normally or into recovery, it showed static (I'll include an image). It does, however, boot into download mode.
So then, I thought I would try and put a new recovery on it through Odin to see if that would fix anything, but upon pushing start in Odin it says no PIT partition and fails.
I have a Nandroid backup made through TWRP (I'm not sure if the one on hand is from stock or right after flashing SlimKat).
In case you need this info, here is what it says when download mode is booted:
ODIN MODE
PRODUCT NAME: SGH-T889
CUSTOM BINARY DOWNLOAD: No
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
KNOX WARRANTY VOID: 0
AP SWREV:
I'm hoping it isn't a hardware issue and that I can, if anything, put it back to stock.
Any help is greatly appreciated! Thank you!
Any update? I have read that when it loses model number it is one of the IC's. I still have model number when linked to odin.
Flashing in Odin may require the original Samsung USB cable in order to read the phone'a partition information.
I was told to put this question on this forum and I'm really hoping someone can help. My phone is in perfect condition and it would be a shame to have to throw it out:
I'm out of Ideas, please help me.
Here is my info:
Samsung galaxy s3 sgh-i747m from kodoo Canada. I had installed cyanogenmod through their installer over a year ago. I have been using it with my rogers sim with no problems. Less than 2 weeks ago my screen randomly goes black. I try pulling the battery. The samsung logo appears but then back to black but I can hear everything is working. I Try and boot into recovery and everything is black. I boot into download mode and everything looks fine. I try reinstalling cyanogenmod and then Samsung stock through kies and smart switch and every stock kodoo file I can find .
There is one of two things that happen.
If I install a stock below 4.4.2 I get fail in Odin 3.07 and this on download mode:
Odin Mode
Product Name: SGH-I747M
Current Binary: Samsung Official
System Status: Official
Qualcomm secureboot: Enable
Warranty Bit: 1
Bootloader AP SWREV: 2
SW REV Check Fail : Fused 2 Binary 1
If I install a stock rom with 4.4.2 or install from Smart Switch
Everything proceeds perfectly but upon reset I see the samsung logo and then nothing just a black screen with the chime in the background. Still can't boot into recovery. I only see the recovery in blue in the upper left corner but then nothing. I believe after all I've tried I must be on 4.4.2
I would greatly appreciate any help you can give me.
Probably a dumb question on my part but what is "smart switch"?
You can't install any ROM below KK if the phone had stock KK installed on a prior occasion.
I think smart switch is like a newer lighter kies but I could be wrong.
I'm not sure but I don't think I had stock kit kat installed, I think it might have been Jellybean. Is there any way to know for sure? The problem is through odin I would always get fail if I tried any stock rom below 4.4.2.
Odin is the best way to flash the phone with a stock ROM.
I have never used Kies so I can't comment on its effectiveness in restoring a phone.
What error are you getting in Odin when flashing an older ROM than Kit Kat?
What bootloader is on your phone? Have you tried flashing KK via Odin 3.07?
The error I get in Odin is just a red Fail after aboot and on my phone screen it says at the bottom SW REV CHECK FAIL: Fused 2 Binary 1. As for the bootloader, how do I find what my bootloader is?
Odin is failing because you are trying to flash a rom that is trying to downgrade the phone's current bootloader. The fact that the phone has a tripped the warranty bit indicates that it has at least a 4.3 bootloader and cannot be flashed with 4.1.1 or 4.1.2, maybe not even 4.3.
Install the Samsung phone info app from the play store to determine the bootloader. You could also try flashing the stock fob firmware via Odin.
I can't install the samsung info app because I cannot see anything on my screen after the samsung logo. Also I'm not sure what fob is but I tried all of these files with odin 3.07 and none of them brought my screen back to life. http://www.sammobile.com/firmwares/database/SGH-I747M/KDO/
Okay, try this:
download tar version of TWRP from here: https://dl.twrp.me/d2att/
download the latest CM11 for the d2lte and save it to an external sd card;
download CM11 gapps and save it to the external sd card with CM11;
place the sd card into the phone;
download Odin version 3.07;
boot the phone into download mode;
launch Odin and connect phone via USB cable;
uncheck everything in Odin except F.reset time;
flash TWRP in Odin;
when you see the word reset in the Odin status window, disconnect the USB cable, remove battery, replace battery, boot into TWRP, flash CM11, flash gapps;
reboot phone;
install Sansung info app.
So I did everything you listed and when I attempt to reboot into recovery, I see the samsung logo appear with a blue "recovery booting" in the top left corner of the screen. They stay on for maybe 1 second and then the screen is black. I'm starting to give up hope
Did you pull the battery after seeing the word "Reset" in the status window? Did you try flashing TWRP again?
audit13 said:
Did you pull the battery after seeing the word "Reset" in the status window? Did you try flashing TWRP again?
Click to expand...
Click to collapse
I did pull the battery out after seeing "reset" and still nothing. Why would flashing TWRP again help? I'll try it again tomorrow. Thanks for trying to help me out here.
Did you pull the battery, replace the battery, and try to boot into TWRP (not the ROM)?
audit13 said:
Did you pull the battery, replace the battery, and try to boot into TWRP (not the ROM)?
Click to expand...
Click to collapse
Yes I pulled and replaced the battery. Booting into twrp is still home, power and volume up at the same time, right? That's what I did but nothing.
So you see nothing on the screen after pressing the buttons? Try flashing cwm.
audit13 said:
So you see nothing on the screen after pressing the buttons? Try flashing cwm.
Click to expand...
Click to collapse
Yes nothing. After flashing TWRP Twice and removing and replacing battery. I boot into recovery. I see the samsung logo with recovery booting in small and blue in the top left corner and then immediately to complete black. I also tried with CWM and the same result.
Can you boot into recovery after flashing stock kit kat via Odin?
If not, it sounds like something may be wrong with the hardware.
Hi everybody,
My friend brought his Galaxy Note 2 to me, and here is what I found:
Recovery mode came up with a bunch of mounting errors.
Apparently he tried to flash a custom ROM via Odin?
I thought that wasn't possible (I have used Odin a lot)?
So, again, Recovery (stock) brought up a bunch of mounting errors, but:
Download Mode still works (Good, right?!?!) :fingers-crossed:
Until I tried to use it. I tried to (Odin):
a) Flash .pit file for N7105 - it hangs on Get PIT for Mapping/Set Partition
b) Flash Original Repair ROM (N7105XXUEML3_OLBEML1_Repair_Firmware_4Files) -also hangs at same part)
By now, the original recovery (that was giving mounting errors) no longer works.
Device is now bootlooping with "Samsung Galaxy Note II N7105" stuck on the screen.
Download Mode *still* works, but nothing is flashing. At all. Custom Recoveries don't work either.
What to do?
Does my friend need a JTAG?
Is the emmc in trouble?
Or is it another problem?
I'm well versed on Odin, and know that these procedures don't take more than a few minutes.
A few seconds in the case of .pit files and recoveries.
What is going on?
I'm stumped. I think my buddy's phone is stuffed too.
Help please? Thank you XDA Ninjas.
Download the latest stock gt-n7105 firmware from here: https://www.sammobile.com/firmwares/galaxy-note-/GT-N7105/ and unzip it once to yield an md5 file.
Download Odin 3.07: https://forum.xda-developers.com/attachment.php?attachmentid=1168421
Open Odin, place the md5 file in the PDA slot, do not check anythin except f reset time. Flash the phone using the OEM USB cable that came with the phone. When you see the word "reset" in the status window, remove the USB cable from the phone, remove the battery, replace the battery, use the button combination to boot into recovery, perform a factory wipe, and reboot.