[Q] Static screen upon boot, no PIT in Odin - T-Mobile Samsung Galaxy Note II

Hi, so I recently rooted, flashed TWRP, and put SlimKat on my phone, and it worked great for a few days, but then all of a sudden it would freeze on the lockscreen. To fix this I would need to pull out the battery or do the hard reboot. Then, today, after doing that once again, when I tried to boot normally or into recovery, it showed static (I'll include an image). It does, however, boot into download mode.
So then, I thought I would try and put a new recovery on it through Odin to see if that would fix anything, but upon pushing start in Odin it says no PIT partition and fails.
I have a Nandroid backup made through TWRP (I'm not sure if the one on hand is from stock or right after flashing SlimKat).
In case you need this info, here is what it says when download mode is booted:
ODIN MODE
PRODUCT NAME: SGH-T889
CUSTOM BINARY DOWNLOAD: No
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
KNOX WARRANTY VOID: 0
AP SWREV:
I'm hoping it isn't a hardware issue and that I can, if anything, put it back to stock.
Any help is greatly appreciated! Thank you!

Any update? I have read that when it loses model number it is one of the IC's. I still have model number when linked to odin.

Flashing in Odin may require the original Samsung USB cable in order to read the phone'a partition information.

Related

[Q] HELP!!!!

I cannot get my phone to boot up. It loads the splash screen and gets stuck there. It doesn't move past that screen. I've tried multiple times going into recovery mode but it won't go. I can get into download mode though. I've tried using Odin 3.07 to reflash the KIES_HOME_I317UCALJ2_I317ATTALJ2_215287_REV04_user_low_ship.tar.md5 from the back to stock rar I found here http://forum.xda-developers.com/showthread.php?p=41340941 and I do not know what to do next. I've even tried flashing a recovery tar file I found here http://forum.xda-developers.com/showthread.php?t=2533333. I've also tried removing the battery, replacing the battery (I have a second battery), and even if I power off the device and plug it up to my charger it loads the splash screen and stays there. I've looked around online and found this http://www.note2forum.com/forum/galaxy-note-2-help/1530-troubleshooting-samsung-galaxy-phone-bootloop.html#post20381 but can't even get to recovery mode to do a data wipe. The last thing I was able to do successfully with my phone was get it back to stock so and do the update to 4.1.2 because it was on 4.1.1 and I've seen something called SDS while searching. Is that what happened here? Is my phone able to be repaired? When I'm in download mode the upper left corner shows the following information:
ODIN MODE
PRODUCT NAME: SGH-I317
CUSTOM BINARY DOWNLOAD: Yes (3 counts)
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
KNOX WARRANTY VOID: 1
RP SWREV
I'm doing some serious reaching here because this is my primary phone, and I'm not familiar with PIT files but what I briefly read stated something about identifying which files go to which partition. I have no experience or knowledge of bootloader functions/changes and I've never checked more than auto reboot and reset time in ODIN. Any help is greatly appreciated.
Update!!! OMG I'm so happy to make progress. I flashed in ODIN the 4.3param_tz.tar file found herehttp://forum.xda-developers.com/showthread.php?t=2497994 and it successfully rebooted me into CWM. I will post the results of a ROM restore I'm attempting shortly. I was able to complete a full restore of a previous ROM and my phone is now currently booting up as I type this. Hopefully nothing goes wrong, but I've gotten farther now than I have in the past 5 hours I've been glued to my laptop. Time for a cig and beer.
Assassyn said:
I cannot get my phone to boot up. It loads the splash screen and gets stuck there. It doesn't move past that screen. I've tried multiple times going into recovery mode but it won't go. I can get into download mode though. I've tried using Odin 3.07 to reflash the KIES_HOME_I317UCALJ2_I317ATTALJ2_215287_REV04_user_low_ship.tar.md5 from the back to stock rar I found here http://forum.xda-developers.com/showthread.php?p=41340941 and I do not know what to do next. I've even tried flashing a recovery tar file I found here http://forum.xda-developers.com/showthread.php?t=2533333. I've also tried removing the battery, replacing the battery (I have a second battery), and even if I power off the device and plug it up to my charger it loads the splash screen and stays there. I've looked around online and found this http://www.note2forum.com/forum/gal...-samsung-galaxy-phone-bootloop.html#post20381 but can't even get to recovery mode to do a data wipe. The last thing I was able to do successfully with my phone was get it back to stock so and do the update to 4.1.2 because it was on 4.1.1 and I've seen something called SDS while searching. Is that what happened here? Is my phone able to be repaired? When I'm in download mode the upper left corner shows the following information:
ODIN MODE
PRODUCT NAME: SGH-I317
CUSTOM BINARY DOWNLOAD: Yes (3 counts)
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
KNOX WARRANTY VOID: 1
RP SWREV
I'm doing some serious reaching here because this is my primary phone, and I'm not familiar with PIT files but what I briefly read stated something about identifying which files go to which partition. I have no experience or knowledge of bootloader functions/changes and I've never checked more than auto reboot and reset time in ODIN. Any help is greatly appreciated.
Update!!! OMG I'm so happy to make progress. I flashed in ODIN the 4.3param_tz.tar file found herehttp://forum.xda-developers.com/showthread.php?t=2497994 and it successfully rebooted me into CWM. I will post the results of a ROM restore I'm attempting shortly. I was able to complete a full restore of a previous ROM and my phone is now currently booting up as I type this. Hopefully nothing goes wrong, but I've gotten farther now than I have in the past 5 hours I've been glued to my laptop. Time for a cig and beer.
Click to expand...
Click to collapse
Good for you! FYI, I think u can do a wipe through adb (adb wipe) I think. Nothing should go wrong after restoring your nandroid. (BTW, it's not sds.)
P.S. get a good beer and relax.
Smack that thanks button if I helped!
Note 2 LTE powered by Illusion ROM and Plasma Kernel.
Sent from dat small country called Singapore.
P.S. replies with quotes will be replied to faster.
Sadly ...we still can't dump that pathetic Knox bootloader ...yet...but progress is being made...
And if not...we can downgrade and still flash any rom we want...g
Sent from my SAMSUNG-SGH-I317 using XDA Premium 4 mobile app

[Q] Firmware upgrade encountered an issue?

I have a Sprint Samsung Galaxy s3 (Pebble Blue).
I downloaded Odin and tried to root it to CF-Root-SGS3, but using this tutorial video: youtube com watch?v=mndQZqom3Ac
Yes, I am a complete noob, therefore it failed. When I tried to turn it back on, it showed me this:
Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again.
I did perform a full back up of my phone on Kies before starting, thankfully, but when I tried performing the emergency firmware recovery, it won't show my device in the list of devices requiring emergency recovery. I also don't know what the recovery code would be.
I also tried performing the firmware upgrade and initialization process, but it required my IMEI number, and I don't know how to find that without my phone working properly.
This is the other info my phone is showing:
ODIN MODE
PRODUCT NAME: SPH-L710
CUSTOM BINARY DOWNLOAD: Yes (4 counts)
CURRENT BINARY: Custom
SYSTEM STATUS: Official
QUALCOMM SECUREBOOT: ENABLE
Warranty Bit: 0
BOOTLOADER RP SWREV: 1
Please help. Thank you so much in advance!
Did you get this taken care of? Hopefully you havent been phoneless for the past few days. Can you still boot into download mode? if you can you should try to Odin the stock tar file for the latest firmware/system update (ND8). It's in a thread here http://forum.xda-developers.com/showthread.php?t=2738533 You should be able try rooting again after this gets your phone up and running again. The only thing to worry about is that YOU CAN NOT DOWNGRADE FIRMWARE after MK3 or ND8 without bricking your phone.
Thank you!
I replied to your message, thanks again!

(issue resolved) note 8.0 stuck on opening screen

I have a Note 8.0 that is stuck in a boot loop. It get to the initial screen. "Samsung Galaxy Note 8.0 GT-N5110" and then screen goes blank and it starts over again. Never goes past this screen. I have flashed a stock rom (\N5110UEU2COI3_N5110XAR2COI3_HOME.tar.md5) using odin. Odin gives me a pass when it is finished but the issue persists.
Any help with this is appreciated.
Re-flash the stock ROM but, before booting for the first time, boot into stock recovery and do a full wipe. This may help get out of the bootloop.
audit13, thanks for the suggestion. I tried 3 times with no success. I did see the android with his belly door opened and the blue box spinning. Didn't see that before. However when I boot into recovery the android's belly door has a red triangle in it. A full wipe/reset has no effect and the symptoms persist.
Any other thoughts? Thanks again
I recommend trying again with Odin 3.07.
In Odin, uncheck everything except f.reset time. Connect the tablet in download mode, flash the tar.md5 file in PDA. When you see the word "Reset" in the status window, remove USB cable, press and hold the power button to power off the unit. After the unit is off, use the key combination to boot immediately into recovery and perform a factory wipe/reset. If that doesn't work, you may need to flash the ROM in combination with a pit file.
audit13, tried your instructions and still ended up with the same issue. I used odin3 v3.07. Can you point me to the pit file you referred to in your previous post.
I have this file - BL_N5110UEU2CNE2_1498778_REV01_user_low_ship.tar.md5
and this - CSC_XAR_N5110XAR2CNE2_1498778_REV01_user_low_ship.tar.md5
Are they of any use to me in this situation?
Thanks again for taking an interest in my problem, Keith
Did you download the stock ROM from sammobile? If you did, you should unzip the file once which gives you a tar.md5 file. It is this tar.md5 that is flashed in the PDA section of Odin 3.07.
SamMobile has many countries listed but not USA. Do I use Cellular South? The file I have been trying was not from SamMobile.
When you boot into download mode, does it give you the model #? Do you see anything about Knox or warranty bit in download mode?
The firmware named in the original post looks like it matches Cellular South.
I'm not sure if the 5110 was sold in the USA. If your model is wifi only, another country may work. If it's celluar, different countries use different frequencies which means cross flashing may work but connectivity (wifi and cellular) may not work.
Download mode shows this:
Odin mode (in red)
Product name: GT-N5110
Current binary: Samsung Official
System status: Custom
Knox Warranty Void: 0
RP SWREV: A2
It's strange that you were able to flash a stock ROM but the system status is "custom".
I suggest trying to flash an entire ROM from sammobile.com similar to the BL and CSC you flashed earlier. It may be simplet to install a custom recovery and flash a custom ROM so you can at least confirm the baseband and bootloader currently installed.
I'll give a custom recovery and rom a try tonight after work. TWRP and any stable build correct?
As for those two separate files, I didn't try anything with them. I downloaded them in case I needed to use them.
This is a board that I got off eBay for $5 and I don't know it's history. Could this issue be hardware related? The board looks good with no signs of corrosion (water damage) of hot spots (electrical surge).
It seems as though it can't find the os on boot.
Thanks again.
Did the board ever boot or was it stuck in a bootloop from the beginning? How did you know which bootloader to flash?
The board has never booted. The only files I have flashed are the one in my first post and the one from SamMobile (Cellular South) as per your instructions. These two files appear to be one in the same. Both files when flashed produced the same result, boot loop.
Do the files contain a boot loader? It sure feels like that is where the problem lies.
Success! Flashed TWRP and then installed SlimKat 4.4.4 and all is working. Need to get gapps installed but for now this board is good.
audit13, thanks again for you interest in my issue.

Samsung Note II Boot Loop

Hi,
I am facing boot loop issue on my N7100 from the time since I updated software.
My Note II motherboard went dead a long time ago so I thought to buy a new motherboard(International Version) from China which I received yesterday. I was able to install the board successfully, phone started working in normal condition, I was really Happy. Very soon, new software update popups started appearing which I decided to install one by one. Initial were some patches, then a big update came for around 800Mb which was for addition of KNOX and other features. The download was completed successfully & and I tried to Install it.
After the installation my phone went into boot loop. The Samsung logo comes and disappears and the cycle goes on.
> I am not able to get phone in recovery mode ( Vol Up+Home+Power).
> Yes, I am able to get phone in download mode (Vol Down+Home+Power).
Following is the status in download mode:
Product Name: GT-N7100
Custom Binary Download: No
Current Binary: Samsung Official
System Status: Custom
Knox Warranty Void: 0
AP SWREV: A2
I did try to re-install ROM using ODIN but failed.
ROM Link : https://www.needrom.com/server/download.php?name=/2017/09/KSA-N7100XXUFNL1-20150518112800.zip
Currently,
a) I don't know the details of motherboard ( S/N, Country Origin, PDA Number, CSC Number ).
b) Developer options were not enabled while phone was in working condition.
c) Tried my best to restore ROM but failed.
I need support to make this phone functional again. I need to know whether the board has gone faulty or can be repaired using software stuff?
Earliest response will be highly appreciated.
Thankyou so much!
Regards
Nikhil
Did you try to flash any non-Samsung software via Odin? I ask because I see the word "custom" in download mode.
What happens when you try to boot into recovery? What happens when you try to flash a stock ROM?
Try flashing a stock recovery from sammobile.com or updato.com.

Need help getting SM-N910P back to stock rom

Let me get you up to speed: From the latest update on the official marshmallow firmware (SM-N910P is my version), I rooted it using odin, then put the wrong version of TWRP on by accident (tbltespr = Note 4 Edge) but then put the right one on (trltespr) but as with everybody else that did this, I got stuck with that horrible screen offset. The *#2663# seemed to ve work until I reboot, so I put LineageOS (14.1 unofficial)(I had already been considering doing this before the incident) thinking it would fix it but all it did was make things worse. I am not stuck in a boot loop, even after all the crap I have tried, I can still flash LineageOS and yes, I can use my S Pen but there are a lot of things I use very often that it won't work with.
Now, on to what I have tried: EVERYTHING! The biggest problem to come out of putting LineageOS on there is that I can no longer downgrade (possibly not at all with any method) using ODIN. I have tried lots and lots of firmware, bootloaders, etc and everytime I get the same error (except for twrp, which I can flash):
SW REV CHECK FAIL : [aboot]Fused 5 > Binary 4
[1] eMMC write fail: ABOOT
So it seems using Odin is out of the question, I have tried downloading thing for custom 6.01 roms that either requires something to be flashed using Odin first, have a link that goes to a 404 page, or is not for my version. I have attempted multiple times to use Kies but it keeps rejecting my serial number. Under the battery, I only find the Hex and Dec, I have tried every number I can find on the box, in the battery, add a 1 or 0 there, shorten it here. I even got some serial number apps downloaded to confirm my serial number but still, nothing worked, so it seems Kies is out of the question as well.
Because I have come across nothing else, I can't confirm if TWRP will work or not so that is my best bet.
So here is what I have come to ask, I need a stock rom, whatever version (since I can just use the update later) that is TWRP flashable, let me repeat, TWRP flashable, no tar or md5 Odin files, TWRP! Thank you for anyone and everyone that help me. I apologize if I am breaking any forum rules, this is my first and most likely last post here.
Extra Tidbit of Info
Also, if this helps at all, this is what my Download Mode screen says when idle/(before I try to flash to it)
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-N910P
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
REACTIVATION LOCK: OFF
KNOX WARRANTY VOID: 0x1 (4)
QUALCOMM SECUREBOOT: ENABLE (CSB)
RP SWREV: S1, T3, R1, A5, P1
SECURE DOWNLOAD : ENABLE
UDC START
Here is an idea, if someone out there could kindly do it for me. Make a TWRP backup image of a factory reset stock rom and share it on google or something. then I should just be able to flash the image, right?
I have a problem on note4 sprint. after install custom rom linkage 15 unofficial naughat, i want to restore to stock rom using odin3 but why always fail. but that is the last stock rom I use.

Categories

Resources