Develop Bugs

[Q] update of stock rom led to recovery failure

Hi,
I just got my Galaxy S III and decided to root it. I had done it before. I made a mistake and it wouldn't reboot, so, I had to put the stock rom on the device again. I found the stock rom, which was a 4.0.4 version and flashed it with no problem. But, then, the automatic update installed the 4.1.1 version. Here is when the problem starts: after installation, when I try to go into the recovery mode to clear the cache, the android is dead with a read triangle above it. I don't know what to do since I want to flash a custom rom.
Oh, a small detail that might be important. The stock rom is flashed using ODIN, but the reboot process is so lengthy, I have to remove the battery and then clear the cache before it fully reboots. At this stage (still 4.0.4) there is no problem with recovery mode and everything is fine. It is only after the update to 4.1.1 that the problem starts.
Your helps are much appreciated.:angel:

rezaasl2000 said:
Hi,
I just got my Galaxy S III and decided to root it. I had done it before. I made a mistake and it wouldn't reboot, so, I had to put the stock rom on the device again. I found the stock rom, which was a 4.0.4 version and flashed it with no problem. But, then, the automatic update installed the 4.1.1 version. Here is when the problem starts: after installation, when I try to go into the recovery mode to clear the cache, the android is dead with a read triangle above it. I don't know what to do since I want to flash a custom rom.
Oh, a small detail that might be important. The stock rom is flashed using ODIN, but the reboot process is so lengthy, I have to remove the battery and then clear the cache before it fully reboots. At this stage (still 4.0.4) there is no problem with recovery mode and everything is fine. It is only after the update to 4.1.1 that the problem starts.
Your helps are much appreciated.:angel:
Click to expand...
Click to collapse
So you can esily flash 4.0.4 with no hiccup but then you get the update (kies I assume) and it fails ?
Do you want to be rooted ?
if not just flash the stock 4.1.1 from Sammobile in Odin and update that way to avoid that Kies garbage

hednik said:
So you can esily flash 4.0.4 with no hiccup but then you get the update (kies I assume) and it fails ?
Do you want to be rooted ?
if not just flash the stock 4.1.1 from Sammobile in Odin and update that way to avoid that Kies garbage
Click to expand...
Click to collapse
Thanks for the reply. I do want to be rooted. Mine is an i747. Can you attach the link so I don't download the wrong one?

rezaasl2000 said:
Thanks for the reply. I do want to be rooted. Mine is an i747. Can you attach the link so I don't download the wrong one?
Click to expand...
Click to collapse
Find your carrier and flash one of these in Odin as they are pre-rooted.
http://forum.xda-developers.com/showthread.php?t=1739426

hednik said:
Find your carrier and flash one of these in Odin as they are pre-rooted.
http://forum.xda-developers.com/showthread.php?t=1739426
Click to expand...
Click to collapse
Thank you so much for the reply. After purchasing my g3 from AT&T, I used the same link you just sent me to flash the device. But it didn't work even though I changed the USB port. It installs SuperSU, but the recovery fails. I will try it one more time before and report back to you.
thanks again.

rezaasl2000 said:
Thank you so much for the reply. After purchasing my g3 from AT&T, I used the same link you just sent me to flash the device. But it didn't work even though I changed the USB port. It installs SuperSU, but the recovery fails. I will try it one more time before and report back to you.
thanks again.
Click to expand...
Click to collapse
It failed again (dead android with a red triangle above it). I have checked the ODIN version, whether the md5 file was downloaded correctly. I'm very frustrated.

rezaasl2000 said:
It failed again (dead android with a red triangle above it). I have checked the ODIN version, whether the md5 file was downloaded correctly. I'm very frustrated.
Click to expand...
Click to collapse
So you can't flash anything 4.1.1 or 4.1.2 ? That's odd that only 4.0.4 works. Does it fail with Kies too ?
What about just rooting using CF-auto root or casual and then flashing a rom ?

hednik said:
So you can't flash anything 4.1.1 or 4.1.2 ? That's odd that only 4.0.4 works. Does it fail with Kies too ?
What about just rooting using CF-auto root or casual and then flashing a rom ?
Click to expand...
Click to collapse
Okay, so, this method didn't work either. I went back to the link you sent me with the pre-rooted version and flashed it. Now, it has the same problem (dead android with red triangle), but RootChecker says that I'm rooted. I don't know what difference that makes.
Any thoughts?

rezaasl2000 said:
Okay, so, this method didn't work either. I went back to the link you sent me with the pre-rooted version and flashed it. Now, it has the same problem (dead android with red triangle), but RootChecker says that I'm rooted. I don't know what difference that makes.
Any thoughts?
Click to expand...
Click to collapse
So cf auto root worked but you can't flash ? You need to install a recovery. Can you flash a custom recovery in Odin or mobile Odin ?
Sent from my SGH-I747 using xda premium

hednik said:
So cf auto root worked but you can't flash ? You need to install a recovery. Can you flash a custom recovery in Odin or mobile Odin ?
Sent from my SGH-I747 using xda premium
Click to expand...
Click to collapse
So, I finally figured it out. I used the samsung galaxy s3 toolkit to install the stock firmware and then I updated it on the phone. Next, I went back to the toolkit and installed the most recent version of CWM on it and everything just worked beautifully. I have LiquidSmooth installed and it works just great.
thank you for the help hendik.
:good:

[Q] Samsung Galaxy S3 AT&T Possible Soft Brick?

So, i decide to root my s3 because i wanted to do some cool stuff. I got odin, got the tar file and tried flashing it. For some reason it didn't work :crying: On odin it gave me a fail. I was in download mode too. So, when i turn on my s3 it is in odin mode but it says "firmware upgrade encountered an issue. Please select recovery mode in Kies & try again." i did this in kies and when it was at like 99% it gives me an error. :crying:
so i tried flashing again in odin still fail, but i get on my s3 SV REV CHECK FAIL: Fused 2 > Binary 0. I have no clue what that means, So, i just want my phone to get working again i dont care about rooting anymore. JUST HELP ME FIX IT!!!!:crying:
BTW: I di root my Kindle Fire a while back so i thought I would have experience with this (i kind of do) but i guess I thought wrong.

Was your phone running a stock 4.3 AT&T ROM? What method did you use to try and root the phone?

audit13 said:
Was your phone running a stock 4.3 AT&T ROM? What method did you use to try and root the phone?
Click to expand...
Click to collapse
i think so and i tired using odin and i put the phone in download mode so i could flash the .tar file

Resistance225 said:
i think so and i tired using odin and i put the phone in download mode so i could flash the .tar file
Click to expand...
Click to collapse
Since your phone was running a stock 4.3 ROM, you can't use Odin to install a stock AT&T 4.3 ROM because it doesn't exist. There are leaked ROMs around that you could try flashing.
Alternatively, you could install a custom recovery and install a custom 4.4.2 ROM.

audit13 said:
Since your phone was running a stock 4.3 ROM, you can't use Odin to install a stock AT&T 4.3 ROM because it doesn't exist. There are leaked ROMs around that you could try flashing.
Alternatively, you could install a custom recovery and install a custom 4.4.2 ROM.
Click to expand...
Click to collapse
I will try to do this! Thanks for helping me though, i will keep you updated. :fingers-crossed:

audit13 said:
Since your phone was running a stock 4.3 ROM, you can't use Odin to install a stock AT&T 4.3 ROM because it doesn't exist. There are leaked ROMs around that you could try flashing.
Alternatively, you could install a custom recovery and install a custom 4.4.2 ROM.
Click to expand...
Click to collapse
I installed a recovery and guess what, it started working again! All my data was still there too! Thanks i really appreciate you taking the time to help me! I also was able to succsessfully root it by using the CF auto root .tar file. Once again, thanks a ton!

Resistance225 said:
I installed a recovery and guess what, it started working again! All my data was still there too! Thanks i really appreciate you taking the time to help me! I also was able to succsessfully root it by using the CF auto root .tar file. Once again, thanks a ton!
Click to expand...
Click to collapse
Glad you got it working. We're all here to help.

Flash stock rom - Keep Root & CWM

Hello, I am currently rooted and have CWM 6.0.4.3. installed. I'm on CM11 but want to go back to stock.. Is there an easy way to keep root and go back to stock. Want stock for a few functions that ROMS dont seem to be offering but can keep root and CWM ??
Thanks.

Which phone do you have? You could try flashing a pre-rooted stock ROM via Odin. Then use Odin to flash CWM.

Bt its better to firstly install ur stock rom and then again root it as it takes no longer than 5 mins

DeathNotice said:
Bt its better to firstly install ur stock rom and then again root it as it takes no longer than 5 mins
Click to expand...
Click to collapse
Ok perfect, thats what I was looking for. Phone btw is S3 - d2att - SGH i747) Sounds good to install the stock rom and re-root.. I'm sure its here but I have searched everywhere to find a tutorial on this and I cannot find a straight answer.
Would you mind giving me the steps or pointing me to a thread that explains how to and has the files in need to download ?

audit13 said:
Which phone do you have? You could try flashing a pre-rooted stock ROM via Odin. Then use Odin to flash CWM.
Click to expand...
Click to collapse
Do you know if there is a step by step on this somewhere ? I dont mind going back to complete stock.. I can just re-root and flash CWM after.
OR
Maybe you could just answer the bigger question : the reason I want to go back to stock is I need to use MHL/HDMI which CM11 doesnt support. I dont want to go back to stock, I would rather even go to another ROM that supports mhl/hdmi.. but if I have to go to stock, than so be it.?

Were you running the stock AT&T 4.3 ROM before you switched to CM11?

audit13 said:
Were you running the stock AT&T 4.3 ROM before you switched to CM11?
Click to expand...
Click to collapse
Yes, I bought the phone new and was running stock, Canadian Rogers version and had changed to CM10, then to 11.

robberrobbie said:
Yes, I bought the phone new and was running stock, Canadian Rogers version and had changed to CM10, then to 11.
Click to expand...
Click to collapse
Since you installed a custom recovery, that would have tripped the Knox counter which voids the warranty. It's not a problem if the phone is working properly.
Did you update to 4.3 or did it come with 4.3?
You may be better off installing a pre-rooted ROM.
http://forum.xda-developers.com/showthread.php?t=1739426

audit13 said:
Since you installed a custom recovery, that would have tripped the Knox counter which voids the warranty. It's not a problem if the phone is working properly.
Did you update to 4.3 or did it come with 4.3?
You may be better off installing a pre-rooted ROM.
http://forum.xda-developers.com/showthread.php?t=1739426
Click to expand...
Click to collapse
It was quite some time ago but I believe I was on ICS 4.0.. and switch to CM from there. Im not worried about the counter for warranty, that's expired on my unit anyways. I just want to be able to use MHL/HDMI function.. so if fine with flashing pre-rooted.. or stock.. or a different ROM that support MHL/HDMI. Can you recommend the easiest route ?

robberrobbie said:
It was quite some time ago but I believe I was on ICS 4.0.. and switch to CM from there. Im not worried about the counter for warranty, that's expired on my unit anyways. I just want to be able to use MHL/HDMI function.. so if fine with flashing pre-rooted.. or stock.. or a different ROM that support MHL/HDMI. Can you recommend the easiest route ?
Click to expand...
Click to collapse
I asked about 4.3 because the 4.3 bootloader cannot be downloaded. Flashing via mobile Odin will not touch the bootloader or modem.
You could try a pre-rooted rom and then flash a custom recovery via Odin.
I use Philz Touch from here: http://goo.im/devs/philz_touch/CWM_Advanced_Edition/d2att

audit13 said:
I asked about 4.3 because the 4.3 bootloader cannot be downloaded. Flashing via mobile Odin will not touch the bootloader or modem.
You could try a pre-rooted rom and then flash a custom recovery via Odin.
I use Philz Touch from here: http://goo.im/devs/philz_touch/CWM_Advanced_Edition/d2att
Click to expand...
Click to collapse
Ok thanks, I will do that. 1 thing I'm not quite sure of is the bootloader situation ? In the first tutorial there is a note : Flashing a prior bootloader can hard/soft brick your device. How do I know ?
I see the steps as:
Extract tar file you downloaded.
Use Odin, put phone into download mode [with phone off, hold vol. down + home + power ], connect to computer and open Odin.
once in odin click the PDA field and select the tar file
Leave Auto Reboot and F. Reset Time checked.
click start and when done let phone reboot.
If you just want a stock, rooted phone with no custom recovery, no plans to flash custom roms, etc. then you can stop HERE.
For my situation, is it just that easy ?

Before flashing, verify the version of your bootloader.

audit13 said:
Before flashing, verify the version of your bootloader.
Click to expand...
Click to collapse
OK I have made an effort to go read and figure out how to find out what version of bootloader on my own.. But i cannot find ? Any chance you know... And could help?

You mentioned your have the i747 and Rogers. Do you have the AT&T s3 (i747) or Rogers/Bell/Telus s3 (i747m)?
What is the most recent stock ROM you had on your phone?

Hey. I got the i747m. As for what was the last stock ROM I had, can't say. I know when I bought the phone it was ICS and I had received and update to jellybean.. But them went to cm10. The tutorial I followed told me had me back everything up, which I did. Have it in a file somewhere on my comp, would that tell me ?
Sent from my SAMSUNG-SGH-I747 using xda app-developers app

If you are flasjing back to stock you should flash back to the same baseband/bootloader that came stock on your phone.
I'm looking for a stock rooted zip for the sasktel i747m (MF1) that i can flash in CWM....I need to go back to stock to fix a data issue that ive encountered through flashing these new d2lte builds...
Does anyone know if a cwm flashable stock rooted rom exists for Sasktel's i747m with baseband MF1 ???I already have the Odin flashable stock rooted zip but don't have a laptop handy until tuesday....And im pretty sure i cant flash that zip in cwm recovery....
Sent from my SAMSUNG-SGH-I747 using XDA Premium 4 mobile app

Ariesdroid said:
If you are flasjing back to stock you should flash back to the same baseband/bootloader that came stock on your phone.
I'm looking for a stock rooted zip for the sasktel i747m (MF1) that i can flash in CWM....I need to go back to stock to fix a data issue that ive encountered through flashing these new d2lte builds...
Does anyone know if a cwm flashable stock rooted rom exists for Sasktel's i747m with baseband MF1 ???I already have the Odin flashable stock rooted zip but don't have a laptop handy until tuesday....And im pretty sure i cant flash that zip in cwm recovery....
Sent from my SAMSUNG-SGH-I747 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I have not seen a stock mf1 ROM that can be flashed in CWM. You could use mobile Odin to flash back to stock and then flash Philz Touch via desktop Odin later.

OK, so back to my question.. If I have the i747M and bought the phone with ICS.. does this help.?

audit13 said:
You mentioned your have the i747 and Rogers. Do you have the AT&T s3 (i747) or Rogers/Bell/Telus s3 (i747m)?
What is the most recent stock ROM you had on your phone?
Click to expand...
Click to collapse
Hey there Audit, Sorry to bother you again, I just dont know how to move forward from here and neeeeeed some help.
I have been reading for days and days have not found a straight answer for my issue and I dont want to just go ahead and start flashing when I dont know if its the right method ?
I dont know how to get back to stock from where I'm at, I dont know how to figure out what bootloader I have (you asked me)
I have found a couple links on XDA that I can follow, I'm just not sure if they apply to my situation ?
This is a pretty detailed response/tutorial, but I dont know if I can just go ahead with this or not ?
http://forum.xda-developers.com/showthread.php?t=2186967
This is also very detailed: http://forum.xda-developers.com/showthread.php?t=1739426
Any help would be greatly appreciated !

robberrobbie said:
OK, so back to my question.. If I have the i747M and bought the phone with ICS.. does this help.?
Click to expand...
Click to collapse
If you are sure you have the Rogers i747m and you have never loaded a stock Rogers 4.3 ROM onto your phone, you could use desktop Odin to flash a pre-rooted 4.1.2 ROM from here: http://forum.xda-developers.com/showthread.php?t=1739426.
Flashing the pre-rooted 4.1.2 ROM will return the phone to completely stock, wipe out all installed apps and data, and you will have root. I do not recommend flashing the Rogers 4.3 pre-rooted ROM from the link.
Once you are able to boot into the phone and set things up, you can flash Philz Touch from Odin which will give you a custom recovery on a rooted stock 4.1.2 ROM.

Back to Stock Rom issue

Hi
I have just restored a stock rom back onto my l9192 using odin, but in download mode it still says custom, is that normal, or is there a way to make it say official again ?
Thanks
JD

Flash stock rom via Odin. Root your phone via Odin. Use Triangle Away.
Sorry for my bad English

Hi
I don't want the phone rooted though ? Will it still get OTA updates currently with the Stock ROM i have on it via Odin?
JD

Flash Stock ROM via Odin. Root your phone. Use triangle away for reset flash counter. Retry flash Stock Rom via Odin. You will get OTA updates Stock Rom
Sorry for my bad English

johnnyduk said:
Hi
I have just restored a stock rom back onto my l9192 using odin, but in download mode it still says custom, is that normal, or is there a way to make it say official again ?
Thanks
JD
Click to expand...
Click to collapse
Flash desired firmware until it shows official status.
Sometimes baseband don't change.
Factory reset, flash firmware let it boot, turno of using power button and restart Odin mode using key combination.
You should get official again.

[Q] Trying to Un-root from CM 12.1.. Failing ):

I was on CM 12.1 and I want to go back to completely stock Note 4, as if I purchased my device from the Sprint Store!
I went to download Odin and the stock firmware of Android 5.0.1 for my device, I followed instructions online, and when I press start in Odin, after about 3 seconds it Fails.
Can I not go back to stock Touchwiz 5.0.1 firmware after being on CM 12.1? I do not have a nandroid backup, and even when I try and access Recovery, it is no longer custom recovery, it is a very simple looking recovery screen, with no option to restore a backup.
What can I do! ): I'm extremely stressed and worried I'm not quite sure what to do.
My phone does go into Download mode just fine and show up in Odin.
Also, my phone actually boots up fine, and works fine, but there is no custom recovery, and Odin is failing when trying to flash the stock firmwares

Down load the latest tar from samsung its in the dev section that will fix your phone with odin

pbedard said:
Down load the latest tar from samsung its in the dev section that will fix your phone with odin
Click to expand...
Click to collapse
Since you're familiar with CM and recent OE1 writes both on TW and CM, can you tell the OP if reactivation lock exists on CM, please? How to disable, if enabled?
He's trying to flash OF5 in Odin but it quickly fails or he's downloading the correct OF5 tar now. Add any suggestions you think he might need when coming from CM12 to stock tar these days.
I suspect the recovery is now stock due to partial flash (if possible), reactivation lock or attempt to root in Odin again.
Thanks in advance.
Sent from my SM-N910P using Tapatalk