[Q] Screen coming off/bent - One (M8) Q&A, Help & Troubleshooting

I purchased a second hand (bad move) HTC One M8. It arrived in the mail with the screen bent off on both sides (see image below). I wanted to know if there is any way to fix this before I send it off to where I bought it from.?
Thanks

Its possible that the battery has gone bad and is starting to off gas. Since the battery is sealed it will start to swell up.
I have seen it happen on iPhones and an M7 (also seen it on devices with removable batteries but in those cases the battery door pops off).
With the M7 the center of the LCD appeared closer to the glass while the top and bottom seemed a tad further away. But it too had the adhesive come loose and the glass bow on the sides.
Id send it back.

Send it back
Sent from my HTC One_M8 using Tapatalk

I had a similar issue, noticed slight screen lift on the right side, worse in the middle of the right edge. Turns out bezel was warped, so glue gave away as screen struggled to straighten out.
I sent in. They replaced the whole bezel.

I had this happen to my HTC One X after I replaced the LCD and did a poor job of reassembling.
Definitely should have been mentioned in the item description, so send it back. You didn't get what you paid for.

Related

Digitizer replacement

Hi, has anyone replaced their digitizer on their desire z/g2? How did it go? It looks easy on the youtube vid.. have any problems? What way did you use to melt the glue? What digitizer did you use, where from?
Any info much appriciated as will be replaceing mine v soon due to 'invisible finger problem' that's driving me nuts..
Thanks..
Sent from my HTC Vision using XDA App
Never done it on a g2 but should be pretty straight forward especially with a video lol. Use a heat gun to melt the glue, pretty much the only tool you SHOULD use to do something like that.
I replaced the digitizer on my third G2 after getting a refurb replacement from T-Mobile that had a black spot inside the actual digitizer glass, not on the outside or inside.
The process is very easy with the video, however, trying to keep dust and fingerprints from getting on the inside of the phone while you're trying to get it back together is a serious pain in the rear! If it's the same video that I watched, just use a hair drier blowing hot air to heat the adhesive on the inside of the digitizer and then pop the digitizer off very very slowly, because you don't want to accidentally bend the metal bezel around the screen.
You also may want to leave the original leftover adhesive on the inside, because when I cleaned mine off, light now always leaks out around the bottom edge of the digitizer, below the menu, home, and search buttons, even though I used the double sided adhesive strips covering the entire length of the bottom, so light shouldn't technically be leaking out. No biggie, though... it works like brand new, now!
Thanks for the reply.. I have seen that video and that's what I was using as a guide.. I ordered the digi today, should be here tomorrow.. the only thing I was wondering was the glueing process, as I have not ordered the double sided glue/tape stuff, as I was just hopeing to still use the original glue as I think you are saying.. I hope that works! Have to be careful like u say with dust/fingerprints etc..
Sent from my HTC Vision using XDA App
Hmm, after reading your post again, maybee I should of bought the double sided tape afterall? Do you think the old leftover glue is enough for the new digi?
Many thanks..
Sent from my HTC Vision usingall XDA App
Run over to radio shack they must have some kind of glue you can use lol. google cell phone screen glue see what info you can find.
Ok, just incase anyone is interested, got my new digitizer, followed the video, used a heat gun cerfully to melt the glue, pulled the old digitizer out, and used the original glue whilst still warm to hold the new digi in, as all of glue stayed on the case rather than on the digi, which was pretty lucky.. put it all back together and everything perfect, touchscreen back to how it should be.. cost me 17 pounds.
Sent from my HTC Vision using XDA App
How was this accompilshed?
I replaced the touch screen as well and the problem persists. Plus I never ran into a part that required a heat gun did I use the wrong item?
A VERY confusing part is getting the midframe to hold to the hinge mounts. The side (black dots all down it) should overlap the stabilizer bar on the hinge. I fidgeted with it for hours until realizing it goes over, and inadvertently damaged the highly sensitive LCD screen, which resulted in me taking the whole thing apart again to replace the LCD and digitizer. UGH!
DO NOT get the cheapo digitizer on Amazon, look for one with gray spots where the menu, home, back and search keys are on the back side. The digitizers without them will not work when you swap over the white button caps on the back. I feel like this information is vital to anyone who is replacing their G2 digitizer, but most guides and videos make no mention of it.
I used a lamp to heat up the glass to remove it the first time. Took too long the second time so I used a hair dryer.
senser1080 said:
A VERY confusing part is getting the midframe to hold to the hinge mounts. The side (black dots all down it) should overlap the stabilizer bar on the hinge. I fidgeted with it for hours until realizing it goes over, and inadvertently damaged the highly sensitive LCD screen, which resulted in me taking the whole thing apart again to replace the LCD and digitizer. UGH!
DO NOT get the cheapo digitizer on Amazon, look for one with gray spots where the menu, home, back and search keys are on the back side. The digitizers without them will not work when you swap over the white button caps on the back. I feel like this information is vital to anyone who is replacing their G2 digitizer, but most guides and videos make no mention of it.
I used a lamp to heat up the glass to remove it the first time. Took too long the second time so I used a hair dryer.
Click to expand...
Click to collapse
So which digitizer did you end up buying and which guide or video did you follow? I am about to tear mine apart and could use the info.
senser1080 said:
A VERY confusing part is getting the midframe to hold to the hinge mounts. The side (black dots all down it) should overlap the stabilizer bar on the hinge. I fidgeted with it for hours until realizing it goes over, and inadvertently damaged the highly sensitive LCD screen, which resulted in me taking the whole thing apart again to replace the LCD and digitizer. UGH!
DO NOT get the cheapo digitizer on Amazon, look for one with gray spots where the menu, home, back and search keys are on the back side. The digitizers without them will not work when you swap over the white button caps on the back. I feel like this information is vital to anyone who is replacing their G2 digitizer, but most guides and videos make no mention of it.
I used a lamp to heat up the glass to remove it the first time. Took too long the second time so I used a hair dryer.
Click to expand...
Click to collapse
Hi, I did buy mine from amazon.co.uk, there were a few for sale,, the one I bought was supposed to be a genuine t-mobile g2 replacement (refurb I think, pressumably this just means that it was from a second hand g2 that had problems and the digi was taken out - and I'm pretty certain this is the case as mine has a thin film (which u leave on) over the back of the digi covering the tracks etc, which had a few very small air/dust bubbles under it (just noticeable when screen off), where I own a desire z, so now it sais t-mobile instead of htc, but I can live with that.
The small grey bits that you talk about were floating about or stuck on my digi when I pulled it off the main chassis. I had a look, and as far as I could work out, were possibly just for giving colour to the tiny led's that give you light to the home/search keys etc (I may be wrong on their use), but if you look closely, the tiny grey things have even smaller rectangles on them that relate to the positions of the led's on the circuit board. So I picked the remaining ones off the old digi, put them back in their correct holes and stuck the new digi in. I've had no problems (with a digi from amazon with no little grey things on it) so far, but maybee this is due to mine being a second hand original part..
Edit : Now after reading your post again, you're talking about bits that are actually on the digi itself, not the white caps that I'm talking about! Whoops. I didn't notice any grey spots on the digi itself, but I guess I must have them..
Sent from my HTC Vision using XDA App
ian577416 said:
I replaced the touch screen as well and the problem persists. Plus I never ran into a part that required a heat gun did I use the wrong item?
Click to expand...
Click to collapse
I rekon u replaced the wrong thing! Maybe the lcd?
Sent from my HTC Vision using XDA App
i just replaced mine with this one:
http://www.ebay.de/itm/230685692541?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
actually it says HTC on it and looks a lil bit differently than on the picture.
never the less, i replaced it really carefully and checked every connecting.
But somehow the Touchscreen doesn't work at all.
Can anyone help me ? what could be the problem ?
Wrong digitzer ?
is it okay, that the digitizer has direct contact to the frame where it is glued to ?
jmpcrx said:
... as will be replaceing mine v soon due to 'invisible finger problem' that's driving me nuts..
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
Hi!
I have the same problem, I have asked it already here
So you had invisible finger press in the screen, and the screen was bad responsive?
...Just to make sure my problem is digitizer problem! The service wont change it in warranty unless the problem is there all the time! But its driving me crazy! why is it happening randomly, why isnt it all the time? How could i make the screen to do this problem when i'm at the service?

[Q] HTC One V bottom cover issue

Hi there,
Just bought the HTC One V. The phone is really good so far but i have one issue with it, the bottom cover leaves a slight gap. i cut my sim card for it and there is still a gap.
Does anyone else has this issue?
Any suggestions
Thanks
Idon't have the issue. Mine fits perfectly. You shoul probably ask for a replacement.
Sent from my HTC One V using Tapatalk 2
I have problems with One V bottom cover too. It leaves a slight gap od the bottom left side (if you look the back of the phone).
This is my third One V.
First one had yellow ring around the display edges, T-mobile got me new immediatley. On second one display got unglued from the phone?!?!? I was amazed!! They gave me new next day.
And now the third one has problems with bottom cover.
I tried 3 different brand new phones in the T-mobile store and they all had this issue.
Honestly, now I hate this phone!
Can someone find why bottom cover cannot fit. Is microphone rubber pushing it out of the socket or is it somethig else??
Replacement. Mine doesn't have a gap either.
Sent from my HTC One V using XDA

[Q] How to repair a broken screen!?

Hi guys,
I have just broken my Dinc2's glass screen. The underlying LCD screen is still functional and the touch screen works. So, I am guessing that I only broke the glass on the top of the screen... I uploaded pics to make it clear.
The casing near the USB port got bent some time back when I went kayaking... And I think that is where the screen cracked significantly when I dropped the phone.
I can still use the touchscreen and there are no discoloration on the LCD. So, can you guys suggest to me what Screen replacement product I need to buy online and (preferably) give me a link for said product and a How to repair guide. Plus, is this process easy? As in if I spend a few hours carefully following the steps to repair, will I succeed?? Moreover, can I replace the metal casing as well?
Thanks for the help gang! I really need to get my phone back to 100% working condition as I don't have an upgrade available till April '13 and I have cancelled my phone's insurance recently!
EDIT: Does this product help? http://www.amazon.com/gp/product/B0057OO9OC/
http://www.repairsuniverse.com/htc-droid-incredible-2-screen-replacements-repair-parts.html
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
So I have dust under my screen even though my phone is completely original and never been dropped. Do you think it's worth taking apart, cleaning out, and replacing the adhesive? How long do you think it would take, and what is the likelihood of doing more damage to the phone?
Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
I bought the following on amazon:
http://www.amazon.com/gp/product/B005GIUHDQ
http://www.amazon.com/gp/product/B0057OO9OC
http://www.amazon.com/gp/product/B002EXHR1Q
I should have probably waited for more replies, like yours, here to get a better product link. Anyway, I guess I bought all the needed parts. I hope I get good quality material and I can get going with the repair... Do you think that they are good? The digitizer and tools didn't ship yet, so I can try and cancel and buy the one from ebay...
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Dermen said:
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Click to expand...
Click to collapse
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
litetaker said:
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
Click to expand...
Click to collapse
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Parts arrived. Links to tutorials PLEASE!
Dermen said:
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Click to expand...
Click to collapse
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
prototype7 said:
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
Click to expand...
Click to collapse
Thanks, captain obvious!
I wanted to know if there is a detailed how to. Anyway, managed to take it apart. All guides end at taking it apart and say, "well, now you know how to dissemble it, just go in reverse and assemble it. Well. I wish they don't do that and show me through the reverse just to avoid mistakes. I remember having to redo IKEA furniture due to missing a few parts. Don't wanna do this messy procedure and realize I forgot a button or worst still putting the screen on!
Anyway, I am a grad student with a bachelors in Engineering... I should be ashamed if I can't do this! :silly:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Dermen said:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Click to expand...
Click to collapse
I am 100% done with the repair. But there are a few issues. The Vibrator motor seems to be not working. Then, the Digitizer I bought doesn't have a hole for the front facing camera! That is not a major setback as I rarely use it and I have a tablet and a PC to skype chat with... But it is sad that a feature is missing.
The big issue is the vibrator not working. I didn't mangle it and put it back in place as I am supposed to. Finally, I have 1 or 2 small dust particles under the screen and that is ok. I couldn't remove all the dust and it is a miracle I managed to get it that clean. Finally I seem to have a slight green tint/screen bleed at top left corner. I didn't have that before and I didn't distort the LCD while replacing. Is it due to a smudge on the LCD there? I suppose it is a minor issue and not something that will amplify as I have a Transformer prime that has screen bleeds and it is apparently because the screws are too tight.. So may be I tightened something too much? Anyway, if it doesn't deteriorate I am ok, as it is a very, very minor problem.
So, bottom line: Main problems > (1) No FFC (due to improper digitizer) -> I don't intend to fix it. (2) Vibrator motor not working.
Can someone help me with 2?
I fricking fixed it! I have WORK to do and I spent about 4 hrs fixing my phone!!! I'm kinda screwed for tomorrow! At least now my phone works...
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Dermen said:
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Click to expand...
Click to collapse
The following are the images of my fixed and "pimped" Dinc2.
https://www.dropbox.com/s/beop9oqvn6qo9p5/2012-09-25 00.23.03.jpg
https://www.dropbox.com/s/qh62damm82z0qmu/2012-09-25 00.22.32.jpg
Is the two tone color combination looking sweet, or should I change the back to red as well? I have a spare black back cover. If anyone has a spare red back cover, I can trade!
Plus, the "smudge/screen bleed" at the top left edge is seen in this pic:
https://www.dropbox.com/s/illeve11tomyrtw/2012-09-25 00.54.23.jpg (The black spot on the middle of the left side is a dust spec!)
Close up: https://www.dropbox.com/s/9ys4r2e6xmxfhnh/2012-09-25 00.54.48.jpg
Is the smudge bad? I think it is just a smudge on the LCD and not a damage to the LCD right? In that case, I am cool, as I most likely will cause other smudges if I attempt to redo it anyway. Plus, I am kinda bummed out about the lack of FFC, but I hardly use it and the whole process of removing the screen is SOOO tedious (and I don't have a heat gun, so had to put my phone a feet above a gas burner! ) and it was so painful and stomach wrenching to safely remove the LCD/digitizer that I don't wish to do it again to repair the FFC...
So, what do ya say?
I think the two tone looks good since the red phones have all black accents. I thought it was weird that the speaker on the red phone is silver, while all the other accents are black.
There seems to be a problem with the adhesive. The digitizer is raised by about 1 millimeter at the top while it is attached better at the bottom. I think it is because I had an additional horizontal strip of adhesive at the bottom to attach the digitizer to both the LCD and the buttons firmly while I didn't put such a horizontal strip at the top as I didn't see one when I dissembled it. If I put pressure on the digitizer for a while, it sets back in place for about half a day. Is this a serious problem? I don't feel like dissembling again.
litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
I just broke my screen and im looking to go the same route. This is a good phone to have as a back up after i get my upgrade and i dont want to get rid of it.
Anyway, did you need all those parts to successfully change your screen? I thought if you bought a new housing you would not need the adhesive tape?

[Q] Metal Body bent after a fall

I recently fell on a very steep step and damaged the metal body of my M8. The phone was in my back pocket which meant that I sat on phone.
Looking at the screen side of the phone ,the body in bent in top right hand corner of the phone and meets up mid way along the length of the volume rocker ( probably the weakest point) I managed to bend it back into roughly the correct shape, however the metal chamfered edge running parallel to the volume rocker was bent in a outward V shape. As the metal is quite malleable, I managed to work it back into shape, but there is still a visible crease..
There is no functional damage. The screen glass is not cracked and the phone works. However it is now irritating every time I look at it. I suppose I will get use to it, but here's the question:
Has any one with a similar problem sent their M8 in for repair with HTC to have the metal body changed for a new metal body? If so, what was the approximate cost? I have emailed HTC and they give the standard repair reply.
5teve0 said:
I recently fell on a very steep step and damaged the metal body of my M8. The phone was in my back pocket which meant that I sat on phone.
Looking at the screen side of the phone ,the body in bent in top right hand corner of the phone and meets up mid way along the length of the volume rocker ( probably the weakest point) I managed to bend it back into roughly the correct shape, however the metal chamfered edge running parallel to the volume rocker was bent in a outward V shape. As the metal is quite malleable, I managed to work it back into shape, but there is still a visible crease..
There is no functional damage. The screen glass is not cracked and the phone works. However it is now irritating every time I look at it. I suppose I will get use to it, but here's the question:
Has any one with a similar problem sent their M8 in for repair with HTC to have the metal body changed for a new metal body? If so, what was the approximate cost? I have emailed HTC and they give the standard repair reply.
Click to expand...
Click to collapse
Look here http://forum.xda-developers.com/showthread.php?p=54861247
n1234d said:
Look here http://forum.xda-developers.com/showthread.php?p=54861247
Click to expand...
Click to collapse
Looks to be an ambitious project, although looking at the price of the body and the time taken to complete the task it has given me an idea of the price HTC might charge me.

HTC one x white screen replacement help

I have the HTC ONE X White AT&T, but I'm stuck on on replacing the screen, every video I can find on the internet is for he black version, and I need help with one part. After the motherboard etc was out, I have to remove the screen, I did, but idk if I got the lcd part too, because it is much thinner than the replacement. there is like 3 layers of paper/plastic s and then a gray screen left. Can anyone help? I can send pic I really really need help I don't want to mess this phone up!
Update
I split the LCD in half it looks like, but the digitizer seems to not be working correctly is there a way to repair it? or do I have to buy a new one?
show some picture. DId you buy lcd+digitizer or only lcd?
it was the combo the digitzer cable (the connector) seems to be bad as it is very difficult to connect compared to the one that came with my phone, when it does connect the touch is very very slow and uncalibrated. Pictures are coming
http://imgur.com/LEzw2aN,pzEvG88,BnrSmTl#0 http://imgur.com/LEzw2aN,pzEvG88,BnrSmTl#1 http://imgur.com/LEzw2aN,pzEvG88,BnrSmTl#2 here are some pics
IS there a way I can repair this?
I think you have a one xl (snapdragon) and not an international (tegra) version in which case it would explain why it doesn't fit or work properly.
If you do have the xl codename evita then you are also in the wrong forum my friend and should head over to the HTC one xl forum.
intel007 said:
I think you have a one xl (snapdragon) and not an international (tegra) version in which case it would explain why it doesn't fit or work properly.
If you do have the xl codename evita then you are also in the wrong forum my friend and should head over to the HTC one xl forum.
Click to expand...
Click to collapse
it says here that it works for both versions though http://www.amazon.com/Display-Digit...qid=1413140433&sr=8-2&keywords=HTC+One+X+AT&T. Every other product had low reviews, is there anywhere I can get a reliable screen replacement?
Pretty much every screen replacement says it doubles up with the HTC One XL. If anyone can help it is greatly appreciated.
can I use the old cable? somehow
Look here mate: http://www.etradesupply.com/htc/android-models/htc-one-x.html
I recently got a HTC screen here and it's perfect & original
Eric4753 said:
can I use the old cable? somehow
Click to expand...
Click to collapse
Hi,
The LCD on the One X and the XL can be different, there is a Sony and a Sharp version which aren't interchangable, but the Digitizer should be essentially the same, as the connectors are identical.
That said, I have come across a dodgy digitizer that was brand new before, and it occasionally does happen. If you want to tell the difference between the sharp and sony version of the LCD, the sharp version gas a green backing to the LCD flex cable while the sony has an orange/yelloy backing to the flex cable, check the attachment i've posted, the one on the left is sony, the one on the right is sharp. It is possible that you have a bad digitizer, but i take it that the LCD works. If thats the case check the connector pins on the main board to make sure they are not damaged (do the same for the digitizer) if it looks ok, and the digitizer is still playing up, i'd try and get a replacement.
Hope this helps
Well I got the thing back together, but I have problems mainly that I'm getting no signal, lastly what thickness of tape should I get?
You may need to open it up again and check everything is connected properly and that it's seated correctly in its rear shell, as there are contacts on the mainboard that touch the antenna mounted inside the shell, hopefully the phone is recognizing the sim and network.
I'm not sure what you want the tape for, could you explain?
We used carpenter's tape, because the tape we supposed to be supplied with didn't come in and the customer is in a rush, I was just asking what should be the thickness of the tape etc
Sorry, I wanted to know what you were going to use tape for, if it was to keep digitizer stuck to frame, I'd use the smallest amount of instant adhesive, being careful not to allow it to run under the glass, where you would see it when you press it down
We'll the screen is almost sticking out of the case despite this being the strongest tape I've ever run into, so I'll guess I'll need thinner tape I just don't want to take everything apart AGAIN and retape. It's a pain to do So should I remove the tape and use glue? Or get thinner tape?
If it's for the back of the LCD get the thinnest double sided tape you can, preferably something reputable like 3m as this is what's going to hold everything in place, if it's the digitizer, I'd use adhesive the tiniest drop in each corner and in the middle of each side, then press until it sets, you just have to be careful as if you use too much it can run from under the glass, and be visible.
---------- Post added at 04:11 PM ---------- Previous post was at 03:44 PM ----------
Just as a tip, you can get a replacement mid frame that already has the 3m tape on it, but I still like to put adhesive on the edges of frame where digitizer sits as sometimes the pressure of putting everything back in the shell can make it pop up.
Well upon taking it back apart the lcd, it got ripped like the bottom half of it is stuck to the tape the top half on the case and there are a bunch of white sheets etc in between them. now should I order a new one or can I repair this? its split in half, nothing is ripped. I'm about to just order a phone off amazon at this point.
You will have to get a new one, look at the videos on YouTube, there are plenty to help, but make sure you keep old one to change over as the phone needs to be turned on to do the LCD change. but if it's really damaged, you cash pick up a used one x reasonably cheaply, but the one m7 or m8 are great phones.

Categories

Resources