Related
Hello,
I dropped my phone (O2 XDA Orbit) this morning and the plastic inset "border" for the screen has come loose on the right hand side and along the top. It looks like its been glued in place orginally and I'm wondering what glue I should use to repair it. Had a quick search through the forums on the site but didn't find anyone talking about this.
Cheers.
Dave.
Dont use super glue as it will likely go white and ruin your screen. Your best bet would be to have the phone professionally repaired. Alternatively, if thats not an option, try a little evo-stick (contact adhesive) sticks like crazy i fused properly. Or theres always "Gorilla Glue" if you can source it on the net, but it needs water as part of the chemical reaction...
nid
dwatkins said:
Hello,
I dropped my phone (O2 XDA Orbit) this morning and the plastic inset "border" for the screen has come loose on the right hand side and along the top. It looks like its been glued in place orginally and I'm wondering what glue I should use to repair it. Had a quick search through the forums on the site but didn't find anyone talking about this.
Cheers.
Dave.
Click to expand...
Click to collapse
I had a bigger problem, I put my full bodily weight on the phone. double and triple cracks along the screen. I bought a new screen and casing on http://cnn.cn for 150 dollars got it within 1 week.
Replacing screen and body is rather easy - do get the right screwdriver here for the very very small screws in body (4) and holding the main pcb (3)
got the original screen - the stickyness of the top layers = touchscreens is rather good. so I wonder how hard you dropped the gizmo
I noticed today that just above the bottom end of the volume rocker, between that and where the screen sits, there was a slight, sharp bump in the polycarbonate. I have managed to smooth it out some what by gently shaving it down with a sharp blade.
So i was wondering, Has anyone else noticed any defects in the casing. Things like sharp ridges, bumps or burr's?
I've not noticed anything on my phone but somebody else on this forum did have one where there was a very thin crack or molding line on one of the corners. They had it replaced IIRC.
My first one had a couple of "air bubbles" in the casing. They were very small. There was also a dark dot on the white surface on the back. I didn't swap the unit out for this..it had other problems.
The one I have now seems to be free of defects. But I did read other reports with similar things.
Perfection....not!
OK, so I'm not the only one. I guess i do have the plus side of i didn't get a white one so if there is any marks on the casing they won't show up as easily.
M3PH said:
I noticed today that just above the bottom end of the volume rocker, between that and where the screen sits, there was a slight, sharp bump in the polycarbonate. I have managed to smooth it out some what by gently shaving it down with a sharp blade.
So i was wondering, Has anyone else noticed any defects in the casing. Things like sharp ridges, bumps or burr's?
Click to expand...
Click to collapse
I have a sharp bump/ imperfection on right below the microUSB slot. Good thing its virtually invisible unless you look for it.
Sent from my HTC One X using Tapatalk 2
bimmerboii said:
I have a sharp bump/ imperfection on right below the microUSB slot. Good thing its virtually invisible unless you look for it.
Sent from my HTC One X using Tapatalk 2
Click to expand...
Click to collapse
I only noticed the one i had because my finger brsuhed over it. I would guess it's a burr from the molding process but then it would be in the same place on every device. Although if there are different molds for the grey/black and white ones then it may just be what i suspect.
As i said in an earlier post, you can get rid of it by using a sharp blade and running of it the bump gently a couple of times to shave it down
Could you post some pictures?
Sent from my HTC One X using XDA
mzaza said:
Could you post some pictures?
Sent from my HTC One X using XDA
Click to expand...
Click to collapse
I would but it doesn't show up so there isn't much point.
Wont it show up in proper lightning angle?
I have on the back a small line which you can see only when holding the phone in proper lightning angle. It's hard to see, I had the phone for 15 days but I just noticed it today.
Sent from my HTC One X using XDA
It's on the opposite side to the dock pins.
Sent from my HTC One X using XDA
mzaza said:
Wont it show up in proper lightning angle?
I have on the back a small line which you can see only when holding the phone in proper lightning angle. It's hard to see, I had the phone for 15 days but I just noticed it today.
Sent from my HTC One X using XDA
Click to expand...
Click to collapse
Nope. I was taking some shots of it today for a review i've done for installornot.com (link in my sig) and it just didn't show up.
But i can describe it as left over from plastic from an injection moulding process. You know how when plastic is injection moulded it leaves a sort of spike where the plastic was injected into the mould. It was exactly like that.
Ah! I've got that too plus the one in the opposite side of the dock I was explaining in the previous post.
Has any one found the same problem, the line on the back?
EDIT: I think it's the borders of the battery because I can see similar lines in proper lightning around the dock pins.
Sent from my HTC One X using XDA
I've found two small defects on the polycarbonate body: one near the 3.5mm jack plug, like a small imperfection such as if the body was hit by something thin like a blade, and another one almost invisible on the left side.. Oh, there is also a very little gray dot on the bottom, but this is really invisible to the most people
mzaza said:
Ah! I've got that too plus the one in the opposite side of the dock I was explaining in the previous post.
Has any one found the same problem, the line on the back?
EDIT: I think it's the borders of the battery because I can see similar lines in proper lightning around the dock pins.
Sent from my HTC One X using XDA
Click to expand...
Click to collapse
The moulding of these cases is really not all that precise but also partly due to the fact that the casing is heated to "glue" bits of plastic and components to the inside back of the case.
I have seen on the white version if you hold it under a spot light and look along its length so you can clearly see the matte mottled effect on the back...then slowly tip the phone back and forth and you will see two horizontal lines running left to right. One a bit above the HTC logo, and one near the speaker grill. It roughly conforms to where the battery is. I also notice that for the line above the HTC logo, towards the right, the moulding dips in ever so slightly. ONce again looking at the inside back, there is some kind of component fixed there. So the cases are just not that precise I'm afraid. Check some of the teardown pictures so you can see the inside of the back casing and you will understand what I mean. It is not just a shell, but an intricate moulding of internal bits as well.
When I first noticed this I was worried if the polycarbonate case was melting due to the heat in the phone. But I googled and found that polycarbonate doesn't start becoming soft until at least 130 degrees C, so it isn't going to be melting!
Your post made me feel better now
jonstatt said:
The moulding of these cases is really not all that precise but also partly due to the fact that the casing is heated to "glue" bits of plastic and components to the inside back of the case.
I have seen on the white version if you hold it under a spot light and look along its length so you can clearly see the matte mottled effect on the back...then slowly tip the phone back and forth and you will see two horizontal lines running left to right. One a bit above the HTC logo, and one near the speaker grill. It roughly conforms to where the battery is. I also notice that for the line above the HTC logo, towards the right, the moulding dips in ever so slightly. ONce again looking at the inside back, there is some kind of component fixed there. So the cases are just not that precise I'm afraid. Check some of the teardown pictures so you can see the inside of the back casing and you will understand what I mean. It is not just a shell, but an intricate moulding of internal bits as well.
When I first noticed this I was worried if the polycarbonate case was melting due to the heat in the phone. But I googled and found that polycarbonate doesn't start becoming soft until at least 130 degrees C, so it isn't going to be melting!
Click to expand...
Click to collapse
Good work there lad.
Hi guys,
I have just broken my Dinc2's glass screen. The underlying LCD screen is still functional and the touch screen works. So, I am guessing that I only broke the glass on the top of the screen... I uploaded pics to make it clear.
The casing near the USB port got bent some time back when I went kayaking... And I think that is where the screen cracked significantly when I dropped the phone.
I can still use the touchscreen and there are no discoloration on the LCD. So, can you guys suggest to me what Screen replacement product I need to buy online and (preferably) give me a link for said product and a How to repair guide. Plus, is this process easy? As in if I spend a few hours carefully following the steps to repair, will I succeed?? Moreover, can I replace the metal casing as well?
Thanks for the help gang! I really need to get my phone back to 100% working condition as I don't have an upgrade available till April '13 and I have cancelled my phone's insurance recently!
EDIT: Does this product help? http://www.amazon.com/gp/product/B0057OO9OC/
http://www.repairsuniverse.com/htc-droid-incredible-2-screen-replacements-repair-parts.html
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
So I have dust under my screen even though my phone is completely original and never been dropped. Do you think it's worth taking apart, cleaning out, and replacing the adhesive? How long do you think it would take, and what is the likelihood of doing more damage to the phone?
Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
I bought the following on amazon:
http://www.amazon.com/gp/product/B005GIUHDQ
http://www.amazon.com/gp/product/B0057OO9OC
http://www.amazon.com/gp/product/B002EXHR1Q
I should have probably waited for more replies, like yours, here to get a better product link. Anyway, I guess I bought all the needed parts. I hope I get good quality material and I can get going with the repair... Do you think that they are good? The digitizer and tools didn't ship yet, so I can try and cancel and buy the one from ebay...
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Dermen said:
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Click to expand...
Click to collapse
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
litetaker said:
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
Click to expand...
Click to collapse
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Parts arrived. Links to tutorials PLEASE!
Dermen said:
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Click to expand...
Click to collapse
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
prototype7 said:
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
Click to expand...
Click to collapse
Thanks, captain obvious!
I wanted to know if there is a detailed how to. Anyway, managed to take it apart. All guides end at taking it apart and say, "well, now you know how to dissemble it, just go in reverse and assemble it. Well. I wish they don't do that and show me through the reverse just to avoid mistakes. I remember having to redo IKEA furniture due to missing a few parts. Don't wanna do this messy procedure and realize I forgot a button or worst still putting the screen on!
Anyway, I am a grad student with a bachelors in Engineering... I should be ashamed if I can't do this! :silly:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Dermen said:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Click to expand...
Click to collapse
I am 100% done with the repair. But there are a few issues. The Vibrator motor seems to be not working. Then, the Digitizer I bought doesn't have a hole for the front facing camera! That is not a major setback as I rarely use it and I have a tablet and a PC to skype chat with... But it is sad that a feature is missing.
The big issue is the vibrator not working. I didn't mangle it and put it back in place as I am supposed to. Finally, I have 1 or 2 small dust particles under the screen and that is ok. I couldn't remove all the dust and it is a miracle I managed to get it that clean. Finally I seem to have a slight green tint/screen bleed at top left corner. I didn't have that before and I didn't distort the LCD while replacing. Is it due to a smudge on the LCD there? I suppose it is a minor issue and not something that will amplify as I have a Transformer prime that has screen bleeds and it is apparently because the screws are too tight.. So may be I tightened something too much? Anyway, if it doesn't deteriorate I am ok, as it is a very, very minor problem.
So, bottom line: Main problems > (1) No FFC (due to improper digitizer) -> I don't intend to fix it. (2) Vibrator motor not working.
Can someone help me with 2?
I fricking fixed it! I have WORK to do and I spent about 4 hrs fixing my phone!!! I'm kinda screwed for tomorrow! At least now my phone works...
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Dermen said:
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Click to expand...
Click to collapse
The following are the images of my fixed and "pimped" Dinc2.
https://www.dropbox.com/s/beop9oqvn6qo9p5/2012-09-25 00.23.03.jpg
https://www.dropbox.com/s/qh62damm82z0qmu/2012-09-25 00.22.32.jpg
Is the two tone color combination looking sweet, or should I change the back to red as well? I have a spare black back cover. If anyone has a spare red back cover, I can trade!
Plus, the "smudge/screen bleed" at the top left edge is seen in this pic:
https://www.dropbox.com/s/illeve11tomyrtw/2012-09-25 00.54.23.jpg (The black spot on the middle of the left side is a dust spec!)
Close up: https://www.dropbox.com/s/9ys4r2e6xmxfhnh/2012-09-25 00.54.48.jpg
Is the smudge bad? I think it is just a smudge on the LCD and not a damage to the LCD right? In that case, I am cool, as I most likely will cause other smudges if I attempt to redo it anyway. Plus, I am kinda bummed out about the lack of FFC, but I hardly use it and the whole process of removing the screen is SOOO tedious (and I don't have a heat gun, so had to put my phone a feet above a gas burner! ) and it was so painful and stomach wrenching to safely remove the LCD/digitizer that I don't wish to do it again to repair the FFC...
So, what do ya say?
I think the two tone looks good since the red phones have all black accents. I thought it was weird that the speaker on the red phone is silver, while all the other accents are black.
There seems to be a problem with the adhesive. The digitizer is raised by about 1 millimeter at the top while it is attached better at the bottom. I think it is because I had an additional horizontal strip of adhesive at the bottom to attach the digitizer to both the LCD and the buttons firmly while I didn't put such a horizontal strip at the top as I didn't see one when I dissembled it. If I put pressure on the digitizer for a while, it sets back in place for about half a day. Is this a serious problem? I don't feel like dissembling again.
litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
I just broke my screen and im looking to go the same route. This is a good phone to have as a back up after i get my upgrade and i dont want to get rid of it.
Anyway, did you need all those parts to successfully change your screen? I thought if you bought a new housing you would not need the adhesive tape?
Recently i received my Xperia Z1C White. After some careful checking (that happens when you are a techy) i noticed that the frame bends slightly inwards at the back side. I made a small example of what i mean on a photo. The problem is. If you can press those parts of the frame inwards, what happens with the waterproof seal between that part of the frame and the plastic bezel on top of this? Is this the case with every Xperia Z1C or is this a rare problem?
I suspect this also is the reason why you can hear a sound while pressing the screen slightly.
Rinneh said:
Recently i received my Xperia Z1C White. After some careful checking (that happens when you are a techy) i noticed that the frame bends slightly inwards at the back side. I made a small example of what i mean on a photo. The problem is. If you can press those parts of the frame inwards, what happens with the waterproof seal between that part of the frame and the plastic bezel on top of this? Is this the case with every Xperia Z1C or is this a rare problem?
I suspect this also is the reason why you can hear a sound while pressing the screen slightly.
Click to expand...
Click to collapse
Same on my phone, but only the charging port side, and my phone squeaks too.
Me too - i can also press the frame inward. Oh my god, i´m a bit confused now...lets hope everything is ok and water is no problem for that...
*EDIT* But i have to say that this also is an issue to find on my Z1 !
Had a bit of convex shape on the back, barely noticeable. Hairdryer and pressing did the trick.
And no, don't be too harsh to the phone.
Glue seems to be unequally applicated.
Made in China after all.
I don't know why, but it doesn't seems any problem with my white phone.
I wonder hwo wide spread or problematic this is. On a normal phone this wouldnt be a problem at all. But on a waterproof phone every error can be a problem.
Mine seems to have the same microscopic gap on the back around the docking port.
I dunked it in a bowl of water and let it sit for 5 minutes. Took it out, dried it off - no problems.
The back of mine flexes when pressed hard in the center, but there are no gaps at the edges (even when pressed)
Is this something they'd accept a warranty replacement for? Where do you go about requesting such?
slvrarrow said:
Is this something they'd accept a warranty replacement for? Where do you go about requesting such?
Click to expand...
Click to collapse
I think no warranty on this, they will probably consider it normal.
The problem with high precision designed devices like this and iphones is, that if something is a bit off you notice it easier.
I do regret it a bit that i didnt exchange it within the 7 days that it is possible to exchange a product after buying it in holland. But if it is widespread, then the case of a phone without the flexing frame/misaligned frame would be very small.
For anyone worried about the waterproof nature of their device, the only thing I can say is - test it. If the product works as intended you're golden. If not, you're covered by warranty.
I'm avid photographer and diver and with all new waterproof equipment, the first thing I do is test their waterproofing by either dunking them in the tub or the sink full of water.
You've bought a device with a capability which you should be able to trust. No need to find out 1 year later when you drop it in the toilet that your device is faulty.
Hejnfelt said:
Mine seems to have the same microscopic gap on the back around the docking port.
Click to expand...
Click to collapse
Same here, only a small gap around docking port that can be ever so slightly pressed in under higher-than-normal pressure, never noticed it in every day handling.
Mine keeps pulling hairs out of my beard!
Sent from my Nexus 7 using Tapatalk
I believe there's a sensor-like surface when you open up one of the flaps (the micro-USB one I think). It's a small white square and it turns red when in contact with water.
This is how the service centres know that you are complying to proper usage. So do be careful not to get the internals wet
That would make sense
Sent from my D5503 using Tapatalk
I have exchanged mine, still a little flex around the charging port but the back is definitely more flush. No small gap and less cracking noise when pressing the back as well. Very content with the built quality of this phone now.
I have the HTC ONE X White AT&T, but I'm stuck on on replacing the screen, every video I can find on the internet is for he black version, and I need help with one part. After the motherboard etc was out, I have to remove the screen, I did, but idk if I got the lcd part too, because it is much thinner than the replacement. there is like 3 layers of paper/plastic s and then a gray screen left. Can anyone help? I can send pic I really really need help I don't want to mess this phone up!
Update
I split the LCD in half it looks like, but the digitizer seems to not be working correctly is there a way to repair it? or do I have to buy a new one?
show some picture. DId you buy lcd+digitizer or only lcd?
it was the combo the digitzer cable (the connector) seems to be bad as it is very difficult to connect compared to the one that came with my phone, when it does connect the touch is very very slow and uncalibrated. Pictures are coming
http://imgur.com/LEzw2aN,pzEvG88,BnrSmTl#0 http://imgur.com/LEzw2aN,pzEvG88,BnrSmTl#1 http://imgur.com/LEzw2aN,pzEvG88,BnrSmTl#2 here are some pics
IS there a way I can repair this?
I think you have a one xl (snapdragon) and not an international (tegra) version in which case it would explain why it doesn't fit or work properly.
If you do have the xl codename evita then you are also in the wrong forum my friend and should head over to the HTC one xl forum.
intel007 said:
I think you have a one xl (snapdragon) and not an international (tegra) version in which case it would explain why it doesn't fit or work properly.
If you do have the xl codename evita then you are also in the wrong forum my friend and should head over to the HTC one xl forum.
Click to expand...
Click to collapse
it says here that it works for both versions though http://www.amazon.com/Display-Digit...qid=1413140433&sr=8-2&keywords=HTC+One+X+AT&T. Every other product had low reviews, is there anywhere I can get a reliable screen replacement?
Pretty much every screen replacement says it doubles up with the HTC One XL. If anyone can help it is greatly appreciated.
can I use the old cable? somehow
Look here mate: http://www.etradesupply.com/htc/android-models/htc-one-x.html
I recently got a HTC screen here and it's perfect & original
Eric4753 said:
can I use the old cable? somehow
Click to expand...
Click to collapse
Hi,
The LCD on the One X and the XL can be different, there is a Sony and a Sharp version which aren't interchangable, but the Digitizer should be essentially the same, as the connectors are identical.
That said, I have come across a dodgy digitizer that was brand new before, and it occasionally does happen. If you want to tell the difference between the sharp and sony version of the LCD, the sharp version gas a green backing to the LCD flex cable while the sony has an orange/yelloy backing to the flex cable, check the attachment i've posted, the one on the left is sony, the one on the right is sharp. It is possible that you have a bad digitizer, but i take it that the LCD works. If thats the case check the connector pins on the main board to make sure they are not damaged (do the same for the digitizer) if it looks ok, and the digitizer is still playing up, i'd try and get a replacement.
Hope this helps
Well I got the thing back together, but I have problems mainly that I'm getting no signal, lastly what thickness of tape should I get?
You may need to open it up again and check everything is connected properly and that it's seated correctly in its rear shell, as there are contacts on the mainboard that touch the antenna mounted inside the shell, hopefully the phone is recognizing the sim and network.
I'm not sure what you want the tape for, could you explain?
We used carpenter's tape, because the tape we supposed to be supplied with didn't come in and the customer is in a rush, I was just asking what should be the thickness of the tape etc
Sorry, I wanted to know what you were going to use tape for, if it was to keep digitizer stuck to frame, I'd use the smallest amount of instant adhesive, being careful not to allow it to run under the glass, where you would see it when you press it down
We'll the screen is almost sticking out of the case despite this being the strongest tape I've ever run into, so I'll guess I'll need thinner tape I just don't want to take everything apart AGAIN and retape. It's a pain to do So should I remove the tape and use glue? Or get thinner tape?
If it's for the back of the LCD get the thinnest double sided tape you can, preferably something reputable like 3m as this is what's going to hold everything in place, if it's the digitizer, I'd use adhesive the tiniest drop in each corner and in the middle of each side, then press until it sets, you just have to be careful as if you use too much it can run from under the glass, and be visible.
---------- Post added at 04:11 PM ---------- Previous post was at 03:44 PM ----------
Just as a tip, you can get a replacement mid frame that already has the 3m tape on it, but I still like to put adhesive on the edges of frame where digitizer sits as sometimes the pressure of putting everything back in the shell can make it pop up.
Well upon taking it back apart the lcd, it got ripped like the bottom half of it is stuck to the tape the top half on the case and there are a bunch of white sheets etc in between them. now should I order a new one or can I repair this? its split in half, nothing is ripped. I'm about to just order a phone off amazon at this point.
You will have to get a new one, look at the videos on YouTube, there are plenty to help, but make sure you keep old one to change over as the phone needs to be turned on to do the LCD change. but if it's really damaged, you cash pick up a used one x reasonably cheaply, but the one m7 or m8 are great phones.