Develop Bugs

Screen died?

Last night I was out and during the night I pulled my desire z out of my pocket to find that the screen was dead, the soft touch buttons were still lit up and working but no display. I pulled the battery and tried to reboot and no luck, you can hear it booting and even unlock/receive calls and txts etc once it has booted up just the screen stays blank the whole time so have to do everything on feel.
Essentially does this just mean my screen has a hardware fault? is it worth trying to fix? I assume the only option would be to purchase a replacement screen and dissemble and reassemble it?
(warranty is not worth it as I live in New Zealand and would have to send my phone back to the UK where I bought it from, also I have dropped it quite a few times so probably voided anyway...)
Thanks in advance for any input

Does it never display anything? So not even a flash during boot or something?
Because then it is probably a hardware problem.
Since the soft touch buttons do still work I think there might be a little crack or something in the flat cable that connects the bottom half with the top.
Maybe you could check whether you can see if the cable is broken or not?
The best thing to do then is to look for a replacement and try to fix it yourself or bring it to a shop where they can do it for you.

No it never displays anything, completely dead the whole time. The touch input is still working though as I answered a phone call this morning on it by making the usual gesture just without being able to see anything. Doesnt seem to be anything wrong with the cable itself as far as I can see. Yea might have to get someone to have a look at it.

My phone is acting the same. I dropped my phone in the pond before, but pulled battery out on time and had it in rice for a day. My phone was still working for about two weeks after that incident. I dropped it and had one little crack at the top of the screen and about a week after that it died when I had a water balloon fight with the phone in my pocket. D;
Do any of you know if the replacement lcd screen/digitizer for the Desire Z would work for the G2?

I had the same thing happening to my G2 screen, only it was intermittently working for a little while, then just completely died and wouldn't work. It was doing this crazy flickering thing then the back light wouldn't go on at all. If I held the phone at a certain angle in the sun, I could see that the pixels were indeed working on the display, but there was no backlight to make them normally visible.
So I purchased a replacement screen from ebay and carefully followed the directions on a youtube video for a G2 take apart. Its not a hard task to take apart and get down to the screen itself. It was rather easy. After putting it back together the screen still didn't work! Sounds work, i can also receive calls etc. But the screen still doesn't work!
Is there any way that this could be a software issue?

Oh and PS, I believe the LCD replacement would work for both the desire Z and the G2. They are identical phones after all right? I'd say its a safe bet. The screen I bought was only 35 bucks. Didn't think that was a bad deal.

Another dead screen or something else?
Few days ago my phone fell of the couch onto a rug - no big deal, so far it has survived much worse, but when I picked it up, the colors were all messed up - overly green and red. Tried restarting - no luck. Everything worked fine, except the colors, but then the screen turned of completely. I could hear notifications, phonecalls, but the screen was dead. After some tapping on the screen, it turned on again - with ****ed up colors. Then started flickering and was gone again. Few more times I could turn it on by tapping before it was dead for good.
Figured, after all these drops it survived, maybe the screen connector is a bit loose. I mean, I could sometime get a contact when tapping it, so I dissasambled it completely, secured all the connection, put it all back tougether and fired up - same thing: dead screen, phone working.
Has anyone had such problem before? Is it screen that is dead, or connector or... I have no clue... I would like try to fix it on my own, with some replacement parts I could get on ebay - but, what gave?

[Q] DInc totally futzed? Probably...

...but it doesn't hurt to ask. I got an old first-day-out DInc that I was using for streaming music (hasn't been a phone in a while). Roughly a year ago, it took a half dip in a toilet. When that happened, my screen started having a blue tint occasionally but I could bend it slightly and the pressure would snap it back. Long story short, never smart to do that to inflexible items, duh. That stopped working a few months ago and I was stuck with a blue tinted screen. This morning I got two bright lines and a screen freeze, so I pulled the battery and restarted and voila! Nothing but a white line and/or the Matrix and when it boots into the OS, the system bar is in the middle of the screen and it doesn't work.
I attached a photo and I was wondering if anyone had any idea about what part could be at fault and if it's even remotely worth it to try and fix it?
Thanks!

One X vs water

So last Thursday I dropped my OneX phone into my kitchen sink full of water & soap. It got fully submerged into it for at least 5 sec.
It still worked completely fine the moment i fished it out, but of course i immediately turned it off
Like 30 minutes later, out of of nowhere my phone came back online without me doing anything. I turned it off but it kept rebooting after showing the HTC splash screen. Water must have done something crazy I don't know...
I put in in a bowl with rice hoping it would dry out. In the meantime it kept rebooting for like 1 hour continuously I kept hearing the vibration
After sometime I noticed it was back on the 'unlock simcard screen' so it finally wasn't rebooting anymore. I unlocked the simcard and have been using my phone perfectly normal.
I've noticed some small darker blotches on the right downside of the screen, but those have slowly dissipated too. And today they are completely gone.
I just wanted to share this little story with you, I'm very happy that my One X survived this 'battle' against water haha.

Haha!! Nice to hear it!
Congo man! Srsly! :good:

Clareyboy said:
So last Thursday I dropped my OneX phone into my kitchen sink full of water & soap. It got fully submerged into it for at least 5 sec.
It still worked completely fine the moment i fished it out, but of course i immediately turned it off
Like 30 minutes later, out of of nowhere my phone came back online without me doing anything. I turned it off but it kept rebooting after showing the HTC splash screen. Water must have done something crazy I don't know...
I put in in a bowl with rice hoping it would dry out. In the meantime it kept rebooting for like 1 hour continuously I kept hearing the vibration
After sometime I noticed it was back on the 'unlock simcard screen' so it finally wasn't rebooting anymore. I unlocked the simcard and have been using my phone perfectly normal.
I've noticed some small darker blotches on the right downside of the screen, but those have slowly dissipated too. And today they are completely gone.
I just wanted to share this little story with you, I'm very happy that my One X survived this 'battle' against water haha.
Click to expand...
Click to collapse
My wife had an One X but first she dropped it in the toilet. Had to wait a few days to let it dry, but it was OK. Then she dropped it again in a puddle full of water. And what was wierd was it worked. Then these blotches appeared
Then about a day later the screen just would be bright at all!.
I tried taking it apart but to my surprise the battery was so soft and would bend super easy. The insides smelled very bad.
It never worked again but I was surprised it lasted as long as it did!
Sent from my HTC One X using xda premium

I do hope for you it will keep working, but to be honest I doubt it. Water does strange things to electronic components.
It may even work fine for days/weeks or months after being in touch with water, but it suddenly can stop working or have other strange reactions due to corrosion or the chemical compounds reacting that were in the water at the time.
I have experienced this behaviour a lot in water damaged electronics, as I'm helping people with insurance claims in my profession. It's difficult to prove problems are connected to water damage, weeks or months after the accident occurred.
Repair centers normally don't give any guarantee on repairs due to water damage, in my experience. That's due to the fact damage may occur even after weeks or months, and it can never be foretold a repair was 100 percent successful.
So, it certainly still could have problems later in time, although of course I hope you were very lucky this time!
Rice is indeed one of the best things to try in these circumstances, it probably saved your phones life this time! :thumbup:

A couple of months ago I spilt lots of pure alcohol on my HOX.
At first these grey spots on the right bottom side appeared and then after turning it off for about 10 hours they vanished but a big wide line appeared in the left side of the screen starting from the bottom until the middle of the screen.
Other than that the phone worked absolutely fine no problem what so ever.
I send the phone to be repaired (screen replacement) last week and got it back two days later with a new screen and a notice that there was no cost charged as the replacement was done under warranty.......
:laugh:

tasos12 said:
A couple of months ago I spilt lots of pure alcohol on my HOX.
At first these grey spots on the right bottom side appeared and then after turning it off for about 10 hours they vanished but a big wide line appeared in the left side of the screen starting from the bottom until the middle of the screen.
Other than that the phone worked absolutely fine no problem what so ever.
I send the phone to be repaired (screen replacement) last week and got it back two days later with a new screen and a notice that there was no cost charged as the replacement was done under warranty.......
:laugh:
Click to expand...
Click to collapse
yes because they thought it was a screen failure...htc wrote in the letter that the screen was abnormal so they replaced it with a complete new...but my screen was broken and repaired with just glued glass ...really nice from them to change the whole screen

Moto Z Play was partially submerged in water, condition deteriorated, won't turn on

My wife dropped her Moto Z Play into a puddle and the bottom half of the phone was submerged. Initially the phone continued to work and she wasn't concerned, so she did not properly dry the phone off. Eventually the screen stopped working and she plugged it in before she told me about it. I dried the phone off as best I could, removing the cover and taking out the sim card. I placed it into rice, where it has been for about a week now. The phone will not power on at all, it makes no noises when plugged in (the phone usually makes a high pitched, very quiet tone when charging). The forward facing light does blink white when it is plugged in but it makes no other response. I do not know what that means and I have not seen anything about it at any forums. The battery is not removable. Any suggestions on what to do now and any explanation on what the blinking white light means? Thanks

same exact situation...
Same thing happened to a friends' moto z play this weekend when she was tubing at a local river. The battery had died so her's was not on when it hit the water and was only submerged for a few seconds. She dried it off best she could and plugged the charger in to see if it would charge. It just blinks the white light on the front three times and then the battery lightning bolt graphic displays momentarily and repeats this. Phone will not turn on as well. We haven't left it on the charger for any period longer than a minute or two. Found this thread, looking for similar situations hopefully for a solution.
FWIW - we did find this youtube video water testing the Z play and it seems as though this phone should be relative water resistant.
since i haven't made 10 posts I cant include url but if you enter watch?v=dxvLKskmkg8 after you tube dot com you can find that video. THIS IS NOT SPAM and very relevant to this thread.
Thanks for sharing @ABTF16 anyhow... Hopefully someone knowledgeable to this scenario will be able to provide an answer at some point in the near future.
ABTF16 said:
My wife dropped her Moto Z Play into a puddle and the bottom half of the phone was submerged. Initially the phone continued to work and she wasn't concerned, so she did not properly dry the phone off. Eventually the screen stopped working and she plugged it in before she told me about it. I dried the phone off as best I could, removing the cover and taking out the sim card. I placed it into rice, where it has been for about a week now. The phone will not power on at all, it makes no noises when plugged in (the phone usually makes a high pitched, very quiet tone when charging). The forward facing light does blink white when it is plugged in but it makes no other response. I do not know what that means and I have not seen anything about it at any forums. The battery is not removable. Any suggestions on what to do now and any explanation on what the blinking white light means? Thanks
Click to expand...
Click to collapse

Quite weird!
It passes the water test with no problem.
Speaker working fine camera working fine touch working fine.??
And in the video he said that the Motorola claims that it has advanced nano coating technology which can protect it from accidental spills or splashes.

Trust me, my Moto X Force went the same way
One second drop in water, it was upright and it was only the bottom inch and for less than one second as I immediately removed it, continued to work for the rest of the day but died in the evening and would not turn on
Sent to Moto and returned with 'unit beyond economical repair' along with a photo and half of the components were corroded
WTF!! one second in water
Don't get me wrong I love Moto's (I have a Z Play now) but they are rubbish if they even get moist

If your phone gets wet you are supposed to leave it off for at least a day in a dry area. I left mine in a hot car with leather seats. You need to let all the components dry out. You could achieve the same affect with a hair dryer.
Turning it on, or trying to charge it is no good idea.
Sent from my Moto Z Play using XDA Labs

ABTF16 said:
My wife dropped her Moto Z Play into a puddle and the bottom half of the phone was submerged. Initially the phone continued to work and she wasn't concerned, so she did not properly dry the phone off. Eventually the screen stopped working and she plugged it in before she told me about it. I dried the phone off as best I could, removing the cover and taking out the sim card. I placed it into rice, where it has been for about a week now. The phone will not power on at all, it makes no noises when plugged in (the phone usually makes a high pitched, very quiet tone when charging). The forward facing light does blink white when it is plugged in but it makes no other response. I do not know what that means and I have not seen anything about it at any forums. The battery is not removable. Any suggestions on what to do now and any explanation on what the blinking white light means? Thanks
Click to expand...
Click to collapse
I had accidently taken my MZP under a running tap and with the pressure the water went all the way inside my MZP but then at first it worked fine for 1 hour or less. Then it switched off automatically and started rebooting. I still managed to get it on then it started to show results like camera stopped working and fingerprint scanner stopped working. I shaked the phone and then removed the water which was remaining. Then I managed to switch it off and then put it in rice for 2 days. After that its working fine, only fingerprint scanner was not working but yesterday it started working and now everything is back to normal. Try isopropyl alcohol which is 99% pure alcohol and then dip your phone in and then put it again for 2 days in rice. I hope this works. However I just needed rice to do its work and mine worked. Hope yours work but if its damaged go to the service centre asap.
:good:

HTC 10 Half of Display Not Working After Screen Replacement

The battery on my HTC 10 was completely shot and needed to be replaced. I'm a careful person by nature and this being my first phone repair, I bought an extra screen just in case something happened getting it apart. Followed a guide by jerryrigeverything on how to take apart the phone, got the battery replaced, everything seemed to go smoothly. When I went to test the display before screwing everything together, the new screen I installed lit up, but the right half of the display only showed as a repeating segment from the middle of the screen. Thinking the connector was loose, I disconnected and reconnected the display and made sure everything was tight: same problem. I reinstalled the original display, which I made sure had worked after cutting through the adhesive before I disconnected it, and now the old display is also showing the same issue.
The touch screen on the broken side of the display still works, I'm able to type PIN numbers and whatnot even though I can't see them properly. Only thing I can think of is maybe the connection actually got some debris or something inside of it? I don't think I damaged anything, as I was super careful, but it was also my first time opening up a phone.
Sorry for the inefficiently worded post. Any help would be really appreciated.

Did you resolve this?
I have exactly the same issue you describe after my screen replacement (with two new screens) Believing the first was a dud.
I have done many screens/batteries on my m7, m8's previously never having a problem.
I'm currently back to running my M8 and miss my 10!
Anyone reading this and has any suggestions they are all welcome!!
Thank you in advance

Exactly the same issue this guy has
https://youtu.be/RpdCuMiTOn8
I'm now wondering if it is just bad aftermarket screens?
Has anyone else replaced their screen successfully, if so where did you get the screen?
Thanks Rory

I have been having the same problem. I just tested screen number 4 that has the same exact problem. Is there a specific brand that is known to test well?

I dropped my 10 in water at work...believe it was a salty water at that. It stopped working completely. I opened the phone to check the internal components for damage and I broke the LCD doing so. I replaced the battery and the screen at almost the same time. I think it may have been a week or two apart.
The battery is still working. The screen worked initially but the phone kept getting really hot and the heat kills the phone. I tried keeping it cool at all times which kept it operational. It hasn't been activated since I quickly replaced the phone with another of my lines upgrades. I went back to the phone to check it out and try using it as a replacement for my daughter but the screen no longer works.
The battery charges just fine...the led light indicates that well. I've tried reinstalling it several times with no success getting the screen working again. I tried the original screen to check and I could see light and it was responding but its not usable so I'm stuck with a phone that has a new non-working display. I think the brand was called DIYRepair or similar.
If anyone has encountered this and has advice...I'd be happy to try anything.