Last night I was out and during the night I pulled my desire z out of my pocket to find that the screen was dead, the soft touch buttons were still lit up and working but no display. I pulled the battery and tried to reboot and no luck, you can hear it booting and even unlock/receive calls and txts etc once it has booted up just the screen stays blank the whole time so have to do everything on feel.
Essentially does this just mean my screen has a hardware fault? is it worth trying to fix? I assume the only option would be to purchase a replacement screen and dissemble and reassemble it?
(warranty is not worth it as I live in New Zealand and would have to send my phone back to the UK where I bought it from, also I have dropped it quite a few times so probably voided anyway...)
Thanks in advance for any input
Does it never display anything? So not even a flash during boot or something?
Because then it is probably a hardware problem.
Since the soft touch buttons do still work I think there might be a little crack or something in the flat cable that connects the bottom half with the top.
Maybe you could check whether you can see if the cable is broken or not?
The best thing to do then is to look for a replacement and try to fix it yourself or bring it to a shop where they can do it for you.
No it never displays anything, completely dead the whole time. The touch input is still working though as I answered a phone call this morning on it by making the usual gesture just without being able to see anything. Doesnt seem to be anything wrong with the cable itself as far as I can see. Yea might have to get someone to have a look at it.
My phone is acting the same. I dropped my phone in the pond before, but pulled battery out on time and had it in rice for a day. My phone was still working for about two weeks after that incident. I dropped it and had one little crack at the top of the screen and about a week after that it died when I had a water balloon fight with the phone in my pocket. D;
Do any of you know if the replacement lcd screen/digitizer for the Desire Z would work for the G2?
I had the same thing happening to my G2 screen, only it was intermittently working for a little while, then just completely died and wouldn't work. It was doing this crazy flickering thing then the back light wouldn't go on at all. If I held the phone at a certain angle in the sun, I could see that the pixels were indeed working on the display, but there was no backlight to make them normally visible.
So I purchased a replacement screen from ebay and carefully followed the directions on a youtube video for a G2 take apart. Its not a hard task to take apart and get down to the screen itself. It was rather easy. After putting it back together the screen still didn't work! Sounds work, i can also receive calls etc. But the screen still doesn't work!
Is there any way that this could be a software issue?
Oh and PS, I believe the LCD replacement would work for both the desire Z and the G2. They are identical phones after all right? I'd say its a safe bet. The screen I bought was only 35 bucks. Didn't think that was a bad deal.
Another dead screen or something else?
Few days ago my phone fell of the couch onto a rug - no big deal, so far it has survived much worse, but when I picked it up, the colors were all messed up - overly green and red. Tried restarting - no luck. Everything worked fine, except the colors, but then the screen turned of completely. I could hear notifications, phonecalls, but the screen was dead. After some tapping on the screen, it turned on again - with ****ed up colors. Then started flickering and was gone again. Few more times I could turn it on by tapping before it was dead for good.
Figured, after all these drops it survived, maybe the screen connector is a bit loose. I mean, I could sometime get a contact when tapping it, so I dissasambled it completely, secured all the connection, put it all back tougether and fired up - same thing: dead screen, phone working.
Has anyone had such problem before? Is it screen that is dead, or connector or... I have no clue... I would like try to fix it on my own, with some replacement parts I could get on ebay - but, what gave?
Related
So... all of a sudden, everytime i slide the screen up, it shuts the screen off. I slide it back, hit the power button a few times, then it turns back on?
NRG GTX 5/9 release
TMO USA
Is my screen busted?
Power off your phone, remove the battery and then put it back in, making sure it fits in there snuggly.
That has happened to me, and removing/replacing the battery fixed it.
Yes, as Amy noted this behavior is often attributed to the battery not sitting exactly right in the compartment. Sometimes just popping it out and back in is enough, but some people have reported needeing to slip a small piece of paper or something similar under the battery cover as well to help keep it snug. (It seems that the sliding motion can be enough to shake the battery off the contacts if it's not secure enough).
Let us know if that clears it up
okay. what the deuce.
my tp2 just literally started doing the same.
earlier today it was perfectly fine.
but now.
i slide out the keyboard and the screen goes blank.
i tried the remove battery and restart.
didn't help.
i tried the paper between battery and cover.
didn't help either.
the screen only goes blank when completely slid out.
if i hold it open just before completely open the screen is still on.
any suggestions?
thanks.
Yea, none of those things worked. However, keeping the battery snug helped with the issue of not hearing anything through the handset.
It honestly sounds to me like both of you are dealing with a loose connection between the screen and the motherboard somewhere, either power or video feed, can't say for sure which. Unless you're willing to disassemble your rhodium (which isn't impossible, just complex), it sounds like it's time to send it to a service center (for AT&T) or to HTC, since that would be a warranty repair.
I hope that this is just freak coincidence that both of you had this happen just now, and not a sign that we're all at risk of having the same issue eventually
How long have each of you had your phones?
EDIT: One more question for you guys...whatever is on the display on your screen rotates into landscape before the display shuts off right?
sirphunkee said:
It honestly sounds to me like both of you are dealing with a loose connection between the screen and the motherboard somewhere, either power or video feed, can't say for sure which. Unless you're willing to disassemble your rhodium (which isn't impossible, just complex), it sounds like it's time to send it to a service center (for AT&T) or to HTC, since that would be a warranty repair.
I hope that this is just freak coincidence that both of you had this happen just now, and not a sign that we're all at risk of having the same issue eventually
How long have each of you had your phones?
EDIT: One more question for you guys...whatever is on the display on your screen rotates into landscape before the display shuts off right?
Click to expand...
Click to collapse
i have own the phone for about three weeks...
though. bought it used from a friend who had it for four months.
but my friend bought it used from somebody too...
aka. not sure how long it has been used.
the display is rotated. and stays on as long as the right side is held.
before the 'tilt piece' is revealed. as soon as it is. the screen goes blank.
and i believe it would be the video feed...
i can still type with the keyboard. just can't see what i am typing.
unless i hold the screen from sliding completely out on the right.
and about the warranty...
would i have a warranty with htc still?
don't have proof of purchase.
just the phone and original box.
thanks.
My AT&T Tilt 2 has been exhibiting this behavior for some weeks now. It seems to be centered around the keyboard slide, but the behavior comes and goes. I found that slamming the phone on the desktop would bring it back to life for a little while, but then it would start to clap out again in a few days. What a pile.
Anyway, I have a fresh one from AT&T to swap out. Now all I have to do is get all my applications and stuff transferred over to the new phone before sending the craprod back to them.
sh4d0w86 said:
i have own the phone for about three weeks...
though. bought it used from a friend who had it for four months.
but my friend bought it used from somebody too...
aka. not sure how long it has been used.
and about the warranty...
would i have a warranty with htc still?
don't have proof of purchase.
just the phone and original box.
thanks.
Click to expand...
Click to collapse
Oh boy...yeah I didn't realize you'd gotten it third-hand. Well it has been less than a year since the Rhodium was released, so it's possible that HTC will still honor the 1-year manufacturer's warranty, but I can't guarantee it. My suggestion would be to just contact HTC America's service group (1-888-617-1113) and see what they say.
Best case: they agree to cover the repair
Worst case: an example of one of the risks you take when you buy something through "unofficial" channels
Yea luckily for me, I bought it second hand, but it was purchased from a retail store, meaning I got a warranty exchange. I just sent it back.
having same issue
im having same issue, when the phone is slid open, goes black, nothing gets it back on, the buttons light up, display dead
however, if i place it in stand by via power button in regular mode, then slide it open, it works, ive rattled and shook the phone, never goes back off, im typing this with it open and tilted....
any ideas?
prob leaving the htc community, samsung captivate, blackberry torch, or htc aria are my choices from at
So I got my Desire Z on Friday and have been LOVING it over the weekend. I got home from work today pressed the power button and the screen just faded into complete white (took about a second to go from off to faded totally to white). I took the battery out, put it back and turned the phone on. Exactly the same from boot. It seems to boot up the phone just with the screen not working. After a couple of minutes the leds flash as would be expected. Opening the keyboard clearly changes things, its clear the screen is trying to rotate. I phoned carphone warehouse and they told me to go to store with it.
Any ideas before I take it back tomorrow?
eviljonny said:
So I got my Desire Z on Friday and have been LOVING it over the weekend. I got home from work today pressed the power button and the screen just faded into complete white (took about a second to go from off to faded totally to white). I took the battery out, put it back and turned the phone on. Exactly the same from boot. It seems to boot up the phone just with the screen not working. After a couple of minutes the leds flash as would be expected. Opening the keyboard clearly changes things, its clear the screen is trying to rotate. I phoned carphone warehouse and they told me to go to store with it.
Any ideas before I take it back tomorrow?
Click to expand...
Click to collapse
Google "white screen of death" -- this can affect different phones from several manufacturers, it seems.
One victim said he took out the battery for 12 hours then got it to boot
Thanks, I had a google around, it doesn't quite look like what a lot of people describe, I had a Powerbook G4 on which the logic board died a while back, it looks exactly like that did once it stopped working.
Even so I've removed my battery and I'll leave it until lunch tomorrow before I pop it back in.
Well I took it into store, they replaced the phone without any issue, hurrah back to a working phone. Lost all my Angry Birds and OpenSudoku progress though, booo.
2 Weeks later and my display is dead again (this was a totally new unit, it wasn't repaired). I'm sure I'm not doing anything out of the ordinary with it. Going to lose my save games again
eviljonny said:
2 Weeks later and my display is dead again (this was a totally new unit, it wasn't repaired). I'm sure I'm not doing anything out of the ordinary with it. Going to lose my save games again
Click to expand...
Click to collapse
What the...
Something else to consider -- I once lost a phone due to a bad car charger -- it was a cheap one that didn't have proper circuit protection, apparently.
In my case it just killed the phone -- no white screen or anything. I just plugged it in, then it was dead.
I also killed the screen digitizer on another phone due to static electricity -- went down a slide with my son with the phone in the pocket -- touched a metal pole and ZAP.
arabic support for desire z
my desire z is operating on 2.3.3 . build number 2.42.405.4.
emails i receive in arabic are not connected.
pls advice how to correct for this.
tq.
Hi. I am not sure this is the BSOD problem that others have had.
I bought a second hand i747. It came with 4.3. It will work fine for a few minutes when first turned on, then the screen will go dark. The menu and back buttons stay lit, and the touchscreen still works, the LCD just cuts off.
If I hit the power button, it sleeps the phone. When I hit again, the screen will come on, but only for about 5 seconds, then it's black again. Everything works, just black screen.
Is it possible for it to overheat or something? It doesn't feel hot at all, but if I turn it off and leave it for awhile, it will again work for about 2-3 minutes, then only about 5 seconds at a time again.
I swapped batteries, and it's the same. The battery had pink on it. I opened it up, and none of the other stickers showed water exposure, and the board itself was clean.
It has stock 4.3, and is not rooted.
I did go to phone settings and turned off the "darken screen during calls" checkbox.
I am wondering if the proximity sensor heats up and shuts the screen off. Grasping at straws I suppose.
Any idea of how to fix this?
Thanks
Perhaps a bad capacitor in the digitizer/lcd assembly? My TV had an issue with a bad capacitor that would cause the screen to blank out after a few minutes???
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
I'll try swapping boards in it later, and maybe at least narrow down if it's the board or the screen assembly. I have an extra proximity sensor I could swap, but it doesn't seem like it's that to me.
thanks, will post more after the board swap
Update: I switched boards (different carriers), and I could not replicate the problem in either phone. I had hoped that would show that either the board or the LCD assembly was bad, but I didn't learn anything useful either way.
I put the boards back in their respective bodies. It still happens now, but not as often. It also appears to be totally random. I did switch batteries in the problem phone, and it doesn't seem as bad. I will try another battery switch and see if that helps it more.
When the screen goes dark, the menu and back buttons are lit. When it went out last night, I could see that there was still some faint background light that I can't see in the day. I pulled up Youtube and did a video, and when the screen went dark, I could still see movement, but couldn't make anything out. So, the phone is still going in the background.
If I push the power button, it sleeps, then push it again, and it wakes up just fine. Sometimes I have to do that 4 or 5 times for the screen to stay on. Sometimes it goes dark after 10 minutes of use, sometimes a half hour, sometimes just a few.
Any help is appreciated.
Well, right before throwing the phone into the wall, I noticed a partially removed liquid exposure indicator. I pulled the phone apart to check the motherboard.
In the process of taking it apart, I forgot to take out the SD card. In so doing, it pulled the sim/sd card module off the motherboard. Low and behold, there was a very light corrosive glaze in a few spots under the module.
So, I got out the 99% IPA, and a toothbrush, and cleaned the whole entire board. Since then, it seems to be working fine.
I don't know exactly what part getting cleaned fixed it, because I just cleaned the whole board.
Anyways, maybe that'll help someone with inexplicable issues downstream.
Thanks for following up with how you fixed the problem. In retrospect, water damage makes sense.
I dropped a Captivate into an ice chest full of melted water last year. I immediately pulled it out and the phone was mostly okay for a while but then the microphone didn't seem to work so well and occasionally the right third of the screen wouldn't respond to touch until I cycled the screen on and off. The water damage sticker and phone interior showed no signs of water.
I will probably sell the old captivate but with full diclosure about the history. Would have been nice if the seller had done the same for you.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Thanks, I should have thought of it sooner, but it didn't seem to have any signs of water damage otherwise.
I ordered the 99% IPA online, because I couldn't find any locally. It works wonders with previously wet boards. You might be able to bring it back.
So during my holiday my HOX got splashed with a bit of water from a wave. The battery was running on fumes and, when I looked at it, the phone was dead. It did turned on later while in my pocket and I happened to press the power button.
I let it dry on rice and nothing. I made the potential mistake of trying to charge it so it would heat up and it wouldn't charge. I then bought another mobile and, just to try it, I took opened the HOX and hoovered. Nothing.
Miracle happened yesterday when, just for kicks, I tried the charger again. It power up!! Everything seems fine, no visible screen damage, wifi works, everything works just fine but... screen won't respond to touch on the very bottom, say, the capacitive and menu buttons (the ones just above the capacitive ones).
What do you guys think? Is the screen dead there, maybe I didn't put the screen back properly or should I wait as some moister might yet be there?
Cheers!
Kutusov said:
So during my holiday my HOX got splashed with a bit of water from a wave. The battery was running on fumes and, when I looked at it, the phone was dead. It did turned on later while in my pocket and I happened to press the power button.
I let it dry on rice and nothing. I made the potential mistake of trying to charge it so it would heat up and it wouldn't charge. I then bought another mobile and, just to try it, I took opened the HOX and hoovered. Nothing.
Miracle happened yesterday when, just for kicks, I tried the charger again. It power up!! Everything seems fine, no visible screen damage, wifi works, everything works just fine but... screen won't respond to touch on the very bottom, say, the capacitive and menu buttons (the ones just above the capacitive ones).
What do you guys think? Is the screen dead there, maybe I didn't put the screen back properly or should I wait as some moister might yet be there?
Cheers!
Click to expand...
Click to collapse
This is a flashback to me. Same thing happened to me few weeks ago - first 3 bottom buttons stoped working, and now 7 days ago part of touch screen is not working anymore. I am going to replace lcd+digitizer+frame, lucky me nothing else need to be fixed. And IMHO trying to heat closed HTC when water was in it doesn't make a sense as a water will condense (as it is closed) so it would make more damage. Oxidation sucks :/
I do have the SIM slot opened but yeah, that's a tinny opening, not much space for water vapour to escape... it's been a few weeks since I thought it had died though, it's pretty amazing to me that it came back at all. Some tough phones, these...
Anyway, I think I'll try to take the screen out again, I wasn't too careful putting it back in because I saw it wasn't charging or powering up or anything at all.
The battery on my HTC 10 was completely shot and needed to be replaced. I'm a careful person by nature and this being my first phone repair, I bought an extra screen just in case something happened getting it apart. Followed a guide by jerryrigeverything on how to take apart the phone, got the battery replaced, everything seemed to go smoothly. When I went to test the display before screwing everything together, the new screen I installed lit up, but the right half of the display only showed as a repeating segment from the middle of the screen. Thinking the connector was loose, I disconnected and reconnected the display and made sure everything was tight: same problem. I reinstalled the original display, which I made sure had worked after cutting through the adhesive before I disconnected it, and now the old display is also showing the same issue.
The touch screen on the broken side of the display still works, I'm able to type PIN numbers and whatnot even though I can't see them properly. Only thing I can think of is maybe the connection actually got some debris or something inside of it? I don't think I damaged anything, as I was super careful, but it was also my first time opening up a phone.
Sorry for the inefficiently worded post. Any help would be really appreciated.
Did you resolve this?
I have exactly the same issue you describe after my screen replacement (with two new screens) Believing the first was a dud.
I have done many screens/batteries on my m7, m8's previously never having a problem.
I'm currently back to running my M8 and miss my 10!
Anyone reading this and has any suggestions they are all welcome!!
Thank you in advance
Exactly the same issue this guy has
https://youtu.be/RpdCuMiTOn8
I'm now wondering if it is just bad aftermarket screens?
Has anyone else replaced their screen successfully, if so where did you get the screen?
Thanks Rory
I have been having the same problem. I just tested screen number 4 that has the same exact problem. Is there a specific brand that is known to test well?
I dropped my 10 in water at work...believe it was a salty water at that. It stopped working completely. I opened the phone to check the internal components for damage and I broke the LCD doing so. I replaced the battery and the screen at almost the same time. I think it may have been a week or two apart.
The battery is still working. The screen worked initially but the phone kept getting really hot and the heat kills the phone. I tried keeping it cool at all times which kept it operational. It hasn't been activated since I quickly replaced the phone with another of my lines upgrades. I went back to the phone to check it out and try using it as a replacement for my daughter but the screen no longer works.
The battery charges just fine...the led light indicates that well. I've tried reinstalling it several times with no success getting the screen working again. I tried the original screen to check and I could see light and it was responding but its not usable so I'm stuck with a phone that has a new non-working display. I think the brand was called DIYRepair or similar.
If anyone has encountered this and has advice...I'd be happy to try anything.