Original Thread by Philz3759:
http://forum.xda-developers.com/note-4/snapdragon-dev/trltexx-philz-touch-t2927930
Recovery Package [Goo]
http://goo.im/devs/playground/trltesku/
This is the CWM-based Philz Touch Recovery with a shiny new kernel, SELinux tweaks, and some other modifications that enable it to run on the N910T and N910W8 out of the box.
May also run on the Sprint and AT&T variants, but make sure to have a copy of a working recovery handy in case you need to restore.
Kernel: http://forum.xda-developers.com/note-4/unified-development/kernel-dealers-choice-t2915824
Device: https://github.com/StarKissed/android_device_samsung_trltetmo
[Recovery]Philz Touch Recovery - Ported to North America
The initial version uses a kernel for the N910W8 and SELinux policy settings from the N910T. If that combination works for me, I can almost guarantee it will work on either of those devices because those values would not match up.
re: Philz Custom Recovery
twistedumbrella said:
Original Thread by Philz3759: http://forum.xda-developers.com/note-4/snapdragon-dev/trltexx-philz-touch-t2927930
Download from Mega
https://mega.co.nz/#F!l1RBBbDI!KHcF184rkhshJhdF_tO7gw
Download from Goo
http://goo.im/devs/playground/trltetmo/recovery
This is the CWM-based Philz Touch Recovery with a shiny new kernel and some other minor tweak that enable it to run on the N910T and N910W8 out of the box.
May also run on the Sprint and AT&T variants, but make sure to have a copy of a working recovery handy in case you need to restore.
Click to expand...
Click to collapse
Thanks for sharing Philz Touch Recovery for our N910T, it's always good to
have a backup custom recovery just in case twrp ever stops working properly.
Misterjunky said:
Thanks for sharing Philz Touch Recovery for our N910T, it's always good to
have a backup custom recovery just in case twrp ever stops working properly.
Click to expand...
Click to collapse
Yeah, I used to just make my own but it's far easier to outsource the core and then replace it with the kernel I'm already working on.
Kernel control apps
twistedumbrella said:
Yeah, I used to just make my own but it's far easier to outsource the core and then replace it with the kernel I'm already working on.
Click to expand...
Click to collapse
Just out of curiosity, in your opinion what is the best app at the play store which
is fully compatible and easy to use with your StarKissed kernels that even noobs
can use without fear of messing anything up when changing the kernel settings?
Thanks!
Thanks.....will wait for corrected upload
louforgiveno said:
Thanks.....will wait for corrected upload
Click to expand...
Click to collapse
It should be uploaded in the next minute or two to Mega and shortly after for Goo
These links not working?
Hanoverfiste said:
These links not working?
Click to expand...
Click to collapse
They should be. I just tried them and they did
twistedumbrella said:
They should be. I just tried them and they did
Click to expand...
Click to collapse
I read back and saw where Tapatalk won't work properly, so I tried through Chrome and that's not working either.
Hanoverfiste said:
I read back and saw where Tapatalk won't work properly, so I tried through Chrome and that's not working either.
Click to expand...
Click to collapse
Mega was the issue on the device, so there is a Goo mirror below it. That should be working.
Or it would have been if I remembered I changed folders on Goo. Now it does.
twistedumbrella said:
Original Thread by Philz3759:
http://forum.xda-developers.com/note-4/snapdragon-dev/trltexx-philz-touch-t2927930
Download from Mega:
https://mega.co.nz/#F!l1RBBbDI!KHcF184rkhshJhdF_tO7gw
Download from Goo:
http://goo.im/devs/playground/trltesku/recovery
This is the CWM-based Philz Touch Recovery with a shiny new kernel, SELinux tweaks, and some other modifications that enable it to run on the N910T and N910W8 out of the box.
May also run on the Sprint and AT&T variants, but make sure to have a copy of a working recovery handy in case you need to restore.
Kernel: http://forum.xda-developers.com/note-4-tmobile/orig-development/kernel-dealers-choice-t2915824
Device: https://github.com/StarKissed/android_device_samsung_trltephil
Click to expand...
Click to collapse
Guys, I don`t know if I am doing something wrong.
I have been using Twrp 2.8.1.1, I used it to flash CWM.
I tried to back up using CWM but says error while making a backup image of /data!
please press any key to continue.
I need help please!
sunnyo_ola said:
Guys, I don`t know if I am doing something wrong.
I have been using Twrp 2.8.1.1, I used it to flash CWM.
I tried to back up using CWM but says error while making a backup image of /data!
please press any key to continue.
I need help please!
Click to expand...
Click to collapse
The partition scheme may be off. I assumed there were identical from Europe to NA but I'll verify that tonight
twistedumbrella said:
The partition scheme may be off. I assumed there were identical from Europe to NA but I'll verify that tonight
Click to expand...
Click to collapse
Thank you, I am using US T-Mobile note 4!
Yeah... The partition scheme is off. I'm on T-Mobile and it won't work. Thanks for your efforts and I can't wait to try again.
[Recovery]Philz Touch Recovery[North American Variants]
Edit: nevermind. The issue is obviously deeper than the fstab or SELinux
Thanks for your hard work. I'm happy to test if you need anything.
After a lot of building, rebuilding, reconfiguring, etc some new builds are finally up.
The current version only supports identifying itself as a T-Mobile device until fully tested.
Rather than modifying the existing European version for the US, this now fully source-built.
twistedumbrella said:
After a lot of building, rebuilding, reconfiguring, etc some new builds are finally up.
The current version only supports identifying itself as a T-Mobile device until fully tested.
Rather than modifying the existing European version for the US, this now fully source-built.
Click to expand...
Click to collapse
Thank you I am going to try it right now,
I will you a feedback.
thank you again for the great work always!
Related
Here are the latest CWM and TWRP ( http://forum.xda-developers.com/showthread.php?t=1809307) recoveries are all flashable from recovery itself, use these to swap back and forth or just because you are bored...
These were/have been previously posted over in sprint apps section, but I keep seeing people posting questions about need this one or that...so here they are for T-Mo.
Thanks goes to the original developers for these, and for the sharing and caring..
TWRP 2.4.2.0 - http://d-h.st/iMc
TWRP 2.4.1.0 - http://d-h.st/9cL
CWM 6.0.2.3 - http://d-h.st/jbT
CWM Touch 6.0.2.3 - http://d-h.st/8A9
Stock ... http://d-h.st/TzP
I made my own months ago, I have tars in my sig and zips in my DropBox (which I've linked several times). You seem to have taken offense at my questions, when I clearly pointed out I didn't want you to interpret them that way. My questioning was merely a vain attempt to learn something new. Not to tear you down, but for me to become more knowledgeable about a subject from someone who clearly knows more about Android than I do.
So, is it safe to flash these?
I could of used you yesterday. I was literally scouring yesterday looking for a flashable recovery. Ended up using adb and Odin to flash something.. Thx for this post.
Sent from my Nexus 7 using xda app-developers app
fasteddie5 said:
So, is it safe to flash these?
Click to expand...
Click to collapse
the CWM are for your phone. TWRP are for all GS III's...I would not have posted these here if they did not work. :victory:
OP updated with specific T-Mo builds so that md5 checks will alleviate anxieties...
Aerowinder said:
I tested both CWM Touch and TWRP myself this morning (latest versions for both). d2spr recoveries (the ones originally posted) absolutely fail the d2tmo assert check (for any zip that includes it).
As of 2012-02-17, 10:50AM EST:
The CWM Touch link is good (it was edited since my last post). Did not test CWM non-touch. Not sure why anyone would use it.
The TWRP 2.4.1.0 link is bad. This is still the d2spr version. Safe to assume the older versions are as well.
Stock recovery link is also bad.
Do not flash recoveries that are not for the T999.
Click to expand...
Click to collapse
The links to the recoveries are fine! The OP is updated with T-Mo provider specific stuff so that MD5/build properties match.
They work just fine. I do have links to sprint ones too. if anyone needs them...
Qverse said:
I agree Aerowinder is very correct ! It still contain the d2spr assert code. cwmtouch-naddict still contains d2spr assert code and will not install on a d2tmo device through recovery. It aborts..
Click to expand...
Click to collapse
good catch, wrong source for TWRP..Corrected and in OP
however, CWM Touch is correct as per what aero said in his post
check OP now. Correct TWRP is up! :cyclops:
source for stock recovery is here http://stockroms.net/file/GalaxyS3/SGH-T999/stockrecovery/T-Mobile-SGH-T999-Stock-Recovery.tar Posted from August 2012. source is attached, do what you want with it. :silly:
Choose to use or not, that is your choice.
I posted them here to help others, and hope someone appreciates them .... Good day
I'm not sure how often stock recovery is updated, but that one is probably from UVALEM.
All checksums match, but assert codes still haven't been removed/fixed. So none of these will flash.
Aerowinder said:
I'm not sure how often stock recovery is updated, but that one is probably from UVALEM.
All checksums match, but assert codes still haven't been removed/fixed. So none of these will flash.
Click to expand...
Click to collapse
try them now..
All should flash, thanks again
Naddict said:
try them now..
All should flash, thanks again
Click to expand...
Click to collapse
Looks good.
Do we just flash, or wipe cache/dalvik first?
fasteddie5 said:
Do we just flash, or wipe cache/dalvik first?
Click to expand...
Click to collapse
Just flash. No need for wipes, since this is replacing your recovery, and not touching your ROM.
Sent from the phalanges of my hand to the facet of your cranium.
Tried flashing CM touch, got install aborted.
fasteddie5 said:
Tried flashing CM touch, got install aborted.
Click to expand...
Click to collapse
redownload the package
Naddict said:
redownload the package
Click to expand...
Click to collapse
OK, I'll try again today. Thanks!
OK, downloaded again, and it failed again. Said, assert failed and some other stuff. I can post everything it says after it fails, if you like.
What device do you have?
If d2tmo, your build.prop has been altered.
Aerowinder said:
What device do you have?
If d2tmo, your build.prop has been altered.
Click to expand...
Click to collapse
TMobile Galaxy S3, running Infamous 4.4
Should I restore to stock rooted, and try that way?
It could be the metadata file within the zip. It's still tagged as d2spr. That file isn't needed, and probably isn't even being read. What is the error saying? I just figured it was a status 7.
Yes, I believe it was status 7.
All Credit to team TWRP / Dees_Troy...Finally working recovery for i9505!
Download the latest 2.6.1.0 tar and img files here: http://www.teamw.in/project/twrp2/182
Update 29/8: There are new releases in both TAR and IMG format directly from the TWRP main site. 2.6.1.0 is out!
It works, now I trying a backup. Seems successful! Thanks a lot.
I would rather see a tar.md5 file then just tar file.
http://www.multiupload.nl/ZQK1OKW1LP
Have one here and would rather see that people use that one, have tried myself and work.
FearKill said:
I would rather see a tar.md5 file then just tar file.
http://www.multiupload.nl/ZQK1OKW1LP
Have one here and would rather see that people use that one, have tried myself and work.
Click to expand...
Click to collapse
Updated link accordingly
Thanks for sharing! Just flashed it on my Phone and works like a charm.
TheMrCaveman said:
Thanks for sharing! Just flashed it on my Phone and works like a charm.
Click to expand...
Click to collapse
Works like a charm )
yes boots and working fine, between boots, but....lack of storage space for system/data (16gb version) and ability to switch to external isnt available as yet..........but, early work,
other options like efs, cache etc all working fine
thanks
EDIT.....MY BAD, JUST TOUCH WHERE IT SHOWS U STORAGE SPACE
gav-collins1983 said:
yes boots and working fine, between boots, but....lack of storage space for system/data (16gb version) and ability to switch to external isnt available as yet..........but, early work,
other options like efs, cache etc all working fine
thanks
Click to expand...
Click to collapse
Are we talking about the same?
I can access my 64gb extFAT sd card just fine! Started Aroma-Filemanager from it.
Touch is a bit too sensitive, but in general it seem to work fine.
harise100 said:
Are we talking about the same?
I can access my 64gb extFAT sd card just fine! Started Aroma-Filemanager from it.
Touch is a bit too sensitive, but in general it seem to work fine.
Click to expand...
Click to collapse
how ? i dont see no option to switch storage, but il go and check now
ha ha ha its touch, durrrrrrrrrrrrrrrrrrrrr, found it
dont be glad so much guys, touch works indeed
But when it comes for installing a rom, touch works no more...i had to continue it with the hard keys,
But one more thing, while installing the omega rom it was so laggy and end with phone shuted down...so no rom flashed
Just flashed the img file using the emulator in rom toolbox and it worked great :thumbup:
Flowed from my GT-I9505 using xda-developers app
mrlove6 said:
dont be glad so much guys, touch works indeed
But when it comes for installing a rom, touch works no more...i had to continue it with the hard keys,
But one more thing, while installing the omega rom it was so laggy and end with phone shuted down...so no rom flashed
Click to expand...
Click to collapse
Omega ROM has been pulled for further testing so there may certainly be issues there, and no doubt there will be further fixes for TWRP
asgard said:
Omega ROM has been pulled for further testing so there may certainly be issues there, and no doubt there will be further fixes for TWRP
Click to expand...
Click to collapse
in fact i have already flashed the rom, but guess what ??? it never boot up lol stuck on samsung logo
Flashed this and it works fine! Many thanks!
Six days since T-Mobile opened up orders on this device, five days since I got my hands on one, and now there's working TWRP. All Cyanogen needs to do is fix the externalSdCard issue in his 10.1 build and this phone will be nearly perfect.
RejjvarN said:
Flashed this and it works fine! Many thanks!
Click to expand...
Click to collapse
Same for me, working to prérooted mdn v2 by Djembey.
many thanks :good:
doesn't works for me
S4 I9505
Issue : flash with odin ok but boot on recovery STOCK finally.
My bootloader is locked, maybe is it the problem ?
Australian S4 I9505 didn't boot recovery. Is there a way to pull some debug logs for you?
Confirmed to be working on Singaporean i9505!
thedt said:
Australian S4 I9505 didn't boot recovery. Is there a way to pull some debug logs for you?
Click to expand...
Click to collapse
Worked fine on my Telstra acquired I9505...
Download files > place file into ODIN (PDA) > reboot phone to DOWNLOAD MODE > run ODIN > boot to recovery
worked like a charm, thanks heaps.
Main thread + features + install instructions + dev support
http://forum.xda-developers.com/showthread.php?t=2201860
PhilZ Touch is a CWM Advanced Edition that adds all the features you could ever miss in CWM
It is a well proven recovery for many phones
It also adds a full touch interface a completely configurable GUI
Please give your feedback, what works, and any bug you could encounter
Read the features, and check if you are missing something
Also, do not forget to read about the powerful aroma file manager integration and double tap shortcut
Download links
Last version can be found here:
Galaxy S2 Epic 4G Touch - SPH-D710 (d710)
http://goo.im/devs/philz_touch/CWM_Advanced_Edition
Click to expand...
Click to collapse
Phil3759 said:
Main thread + features + install instructions + dev support
http://forum.xda-developers.com/showthread.php?t=2201860
PhilZ Touch is a CWM Advanced Edition that adds all the features you could ever miss in CWM
It is a well proven recovery for many phones
It also adds a full touch interface a completely configurable GUI
Please give your feedback, what works, and any bug you could encounter
Read the features, and check if you are missing something
Also, do not forget to read about the powerful aroma file manager integration and double tap shortcut
Download links
Last version can be found here:
Click to expand...
Click to collapse
First off let me say thank you for bringing this amazing recovery to our phone I just flashed it and everything seems good so far,,i'll let you no if i run into any issues
Well using this recovery on mokee the rom will not boot just goes to a black screen so i guess it has to be built with the mokee stuff if you can give me the issues your having i can get it to work,,unless you can give me the source or let me know how to get it and i can make a build using the mokee trees
Phil3759 said:
Main thread + features + install instructions + dev support
http://forum.xda-developers.com/showthread.php?t=2201860
PhilZ Touch is a CWM Advanced Edition that adds all the features you could ever miss in CWM
It is a well proven recovery for many phones
It also adds a full touch interface a completely configurable GUI
Please give your feedback, what works, and any bug you could encounter
Read the features, and check if you are missing something
Also, do not forget to read about the powerful aroma file manager integration and double tap shortcut
Download links
Last version can be found here:
Click to expand...
Click to collapse
Does this work for touch wiz?
It is only for CM based ROMs under KitKat
AOKP ROMS could or could not load
TW will not
For non working roms, you just have to ask someone to repack it with matching kernel zImage
This recovery is pretty awesome, flashed CM11, Vanir, & Commotio successfully.
My new default recovery. :]
HighxVoltage said:
This recovery is pretty awesome, flashed CM11, Vanir, & Commotio successfully.
My new default recovery. :]
Click to expand...
Click to collapse
What was your install method ? I'd like to try it . Did you just flash it with the cwm you already had ? Next question . After you install it and when you flash another rom does it get over written or can you reinject it each time ? thanks
SuperGoober said:
What was your install method ? I'd like to try it . Did you just flash it with the cwm you already had ? Next question . After you install it and when you flash another rom does it get over written or can you reinject it each time ? thanks
Click to expand...
Click to collapse
Yes. & it does get overwritten, I just flash it after flashing the ROM / Gapps. No biggie though. Haven't found an option to make it stick after flashing a ROM like in TWRP.
Sent from my SPH-D710 using Tapatalk
HighxVoltage said:
Yes. & it does get overwritten, I just flash it after flashing the ROM / Gapps. No biggie though. Haven't found an option to make it stick after flashing a ROM like in TWRP.
Sent from my SPH-D710 using Tapatalk
Click to expand...
Click to collapse
I seem to be in a vicious cycle . Recovery flashes fine . When i reboot screen goes black after splash screen . Go back into recovery have to reflash rom but then reflash this and back to black screen on reboot . I don't get what the advantage is if you can't stick it and be able to boot . It would be great if it would stick and boot .
Phil3759 said:
It is only for CM based ROMs under KitKat
AOKP ROMS could or could not load
TW will not
For non working roms, you just have to ask someone to repack it with matching kernel zImage
Click to expand...
Click to collapse
Can you build the recovery using this kernel and vendor files because when CM made there graphics update it caused video issues on our device this kernel and vendor revert that update
https://github.com/mtb3000gt/android_kernel_samsung_d710
https://github.com/mtb3000gt/android_vendor_samsung_d710
https://github.com/mtb3000gt/android_vendor_samsung_d710-common
mtb3000gt said:
Can you build the recovery using this kernel and vendor files because when CM made there graphics update it caused video issues on our device this kernel and vendor revert that update
https://github.com/mtb3000gt/android_kernel_samsung_d710
https://github.com/mtb3000gt/android_vendor_samsung_d710
https://github.com/mtb3000gt/android_vendor_samsung_d710-common
Click to expand...
Click to collapse
yes, but please, no need to post multiple times
once is enough
do i go to recovery and flash this? i am on android 2.3.6, the current recovery only has 3 menu items to do (flash, wipe and wipe)
my goal is to flash the lastest 4.4.3 rom
When I try to flash philz_touch_6.19.3-d710.tar.md5 with Mobile Odin, I get the error "partition could not be found in file". I've done a hash check on the file.
unknownsoldierx said:
When I try to flash philz_touch_6.19.3-d710.tar.md5 with Mobile Odin, I get the error "partition could not be found in file". I've done a hash check on the file.
Click to expand...
Click to collapse
Did you ever get the right file? If not, let me know. I tried to flash it through Mobile Odin and it dosen't even see the files. The best bet is to boot into recovery, flash Philz, reboot into recovery, flash until tired.
Never did get philz_touch_6.19.3-d710.tar.md5 to work. The zip version flashed fine from StockCWM-EL26. I was hoping to get the tar.md5 to work so I could skip StockCWM-EL26.
Then I learned Philz doesn't work properly for nandroids, Since I need to use StockCWM-EL26 for nandroids anyway, the tar.md5 version of Philz is not needed.
unknownsoldierx said:
Never did get philz_touch_6.19.3-d710.tar.md5 to work. The zip version flashed fine from StockCWM-EL26. I was hoping to get the tar.md5 to work so I could skip StockCWM-EL26.
Then I learned Philz doesn't work properly for nandroids, Since I need to use StockCWM-EL26 for nandroids anyway, the tar.md5 version of Philz is not needed.
Click to expand...
Click to collapse
OK. If your on stock, that should be TouchWiz. I would try to install AGAT's as a regular recovery. All the TW ROMs I flashed, had AGATs already installed. The only time I had to use EL26 or EL29 was to go to a different ROM. Have you tried his repository?
here ya go.
http://www.rwilco12.com/downloads.p... (SPH-D710VMUB)/Kernels/Stock (TW) Kernels/JB
CWM-EL26 has worked fine for me, so I haven't used Agat's, Doesn't matter since I don't keep anything installed. I flash a recovery, flash a rom, to see if things are working well enough to use. After not being able to get text or mms to work reliably, I go back to stock completely. GB28 everything.
If there was a custom recovery with a GB28 kernel, I'd keep that installed.
unknownsoldierx said:
CWM-EL26 has worked fine for me, so I haven't used Agat's, Doesn't matter since I don't keep anything installed. I flash a recovery, flash a rom, to see if things are working well enough to use. After not being able to get text or mms to work reliably, I go back to stock completely. GB28 everything.
If there was a custom recovery with a GB28 kernel, I'd keep that installed.
Click to expand...
Click to collapse
Like these?
GB27 will work flawlessly on Virgin and Boost models
Still having a ton of problems with this recovery. It's the only one I can find that will flash the Liquid Smooth rom for me.
The backup/restore seems to be completely broken. Others have said to use another recovery for that. So I flash a recovery, reboot to that, then flash Philz, then flash KK rom.
Today I flashed Liquid Smooth, had some problems with it so decide to restore a backup. I booted into Philz, used it's convenient "wipe for new rom" to make sure everything was clean for restore. Then I needed to flash the recovery I used to make my backup, but when I tried to do that I just got an error 7. I tried flashing different recoveries, roms, modems. All gave errors.
Saw a tip suggesting to untick the "Don't allow old update-binary " option, but that didn't fix it.
Had to hook it up to the computer and flash a recovery using odin.
This
Phil3759 said:
http://goo.im/devs/philz_touch/CWM_Advanced_Edition
Click to expand...
Click to collapse
download link doesn't work any more.
Can anybody please provide me with an alternative download link?
Thanks!
I found working versions for the SPH-D710 here
I just flashed CM11 with the philz_touch_6.19.3-d710.zip and it worked just fine (I think the lower version did not work ...).
This is a source-built version of CWM version 6.0.4.9 for Oneplus ONLY. Do not attempt to use this recovery on any other device.
Tested on Oneplus 64 Gb and 16 GB
Features:
OpenRecoveryScript-compatible
Backup/Restore
Mount/Unmount/Format Partitions
Warnings:
- I am not to be held responsible if you brick your device using this.
Bugs:
I have not managed to find any. If you find one, feel free to let me know.
Additional Notes:
- I will attempt to maintain this in my spare time. If a new release comes out that you are interested in and I have not updated yet, feel free to let me know.
- To flash this unzip files and click on recovery_start.bat
- To flash via fastboot, use only the Recovery Image File.
Download:
Version 6.0.4.9 (June 11th, 2014)
Link
http://d-h.st/XZ9
EDIT: Typo corrected in OP.
dansou901 said:
Kindle Fire HD 7? In Oneplus One section?
Click to expand...
Click to collapse
sorry typo error. Recovery is for oneplus
@acer73 any chance at compiling the touch version?
dmo580 said:
@acer73 any chance at compiling the touch version?
Click to expand...
Click to collapse
This is last ver with swipe (touch)
acer73 said:
This is a source-built version of CWM version 6.0.4.9 for Oneplus ONLY. Do not attempt to use this recovery on any other device.
Tested on Oneplus 64 Gb and 16 GB
Features:
OpenRecoveryScript-compatible
Backup/Restore
Mount/Unmount/Format Partitions
Warnings:
- I am not to be held responsible if you brick your device using this.
Bugs:
I have not managed to find any. If you find one, feel free to let me know.
Additional Notes:
- I will attempt to maintain this in my spare time. If a new release comes out that you are interested in and I have not updated yet, feel free to let me know.
- To flash this unzip files and click on recovery_start.bat
- To flash via fastboot, use only the Recovery Image File.
Download:
Version 6.0.4.9 (June 11th, 2014)
Link
http://d-h.st/XZ9
Click to expand...
Click to collapse
grazie mille
ha qualche bug ?
Don't quote OP and please use English.
good news!thanks!
Dualboot
Hi everyone
I have a Xiaomi M2s right now and the thing i like the most about the device is that it has 2 system partitions and that I can install MIUI on my first partition and CM11 on my second partition. This is ideal if you want to test a ROM but keep one stable system.
Is there any chance that there will be a way to re-partition the one plus to have this? Also CMW would need to have true dual boot right or is this a stock feature?
I don't know if partitioning is common on other devices?
The backups created appear to not have the correct dates for filenames. They start with 1970...
Is this a offical build? Will it be listened on clockworkmod.com anytime soon?
Does anybody have problems with mounting the SD card through CWM? On my device CWM wont backup because of not being able to mount the sd card. I solved this error by reflashing CWM through fastboot, but why does this error occur?
fiz:ik said:
Does anybody have problems with mounting the SD card through CWM? On my device CWM wont backup because of not being able to mount the sd card. I solved this error by reflashing CWM through fastboot, but why does this error occur?
Click to expand...
Click to collapse
Seems that it happens on all recoveries ATM. Happened to me on TWRP. hopefully the developers can fix the source of the problem soon.
What ROM were you running when this happened? I'm trying to narrow down whether its a ROM or recovery issue...or both...
Sent from my Nexus 7 using Tapatalk
MontAlbert said:
Seems that it happens on all recoveries ATM. Happened to me on TWRP. hopefully the developers can fix the source of the problem soon.
What ROM were you running when this happened? I'm trying to narrow down whether its a ROM or recovery issue...or both...
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
Had the problem with Mahdi rom and Philz or cwm ... Hope they will fix this soon !
I found this .. Not really perfect :/ http://forum.xda-developers.com/showpost.php?p=54112729&postcount=24
MontAlbert said:
Seems that it happens on all recoveries ATM. Happened to me on TWRP. hopefully the developers can fix the source of the problem soon.
What ROM were you running when this happened? I'm trying to narrow down whether its a ROM or recovery issue...or both...
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
I'm on stock CM11S
I'm try to build a lot of rom but all of these bootloop or take a lot of time to start, or data partition unmount itself after a reboot.
No issue using PA version 20140708
So I think there is some issue in the last sources,otherwise if it was a problem of recovery also paranoid should have bootloop.
Now I'm trying to build PA with last sources
what about an update?touch edition?
blade_ said:
what about an update?touch edition?
Click to expand...
Click to collapse
Would be great, I hate TWRP and Philz, too. CWM is sufficient, but this project here looks abandoned
blade_ said:
what about an update?touch edition?
Click to expand...
Click to collapse
I actually hate recovery touch editions! When I had the ghost touches it f*cked up everything in recovery.
wacky.ddw said:
I actually hate recovery touch editions! When I had the ghost touches it f*cked up everything in recovery.
Click to expand...
Click to collapse
no problems in all my phones with touch
Disclaimer: I am not responsible if you use this and brick your device or if your device blows up, catches fire, you get fired because the alarm failed, and global thermonuclear war
Kali Nethunter ported to the Samsung Galaxy S3​REQUIREMENTS:
A Samsung Galaxy S3 USA CURRENTLY RUNNING CM11 failure to have this will result in a brick and possibly even a HARD BRICK
A functioning brain
A working recovery
Basic instruction following skills
STEPS:
Download the two zips and copy them to your phone
Link for file 1: https://drive.google.com/open?id=0B5BIHhwzM7wWdDhnbW9xR0E3d2M
Line for file 2: https://drive.google.com/file/d/0B5BIHhwzM7wWSDA5MmZmMjN1TFE/view?usp=sharing
Reboot into recovery
Flash the zips in either order.
???
Profit.
Use make kali_defconfig to make the Kali Kernel correctly if compiling
Please post flash time and results below, this should work on ALL d2 devices under the d2lte label CM uses.
XDA:DevDB Information
Kali Nethunter for d2lte , ROM for the Sprint Samsung Galaxy S III
Contributors
dank101
Source Code: https://bitbucket.org/dank101/android_kernel_samsung_d2_kali
ROM OS Version: 4.4.x KitKat
ROM Kernel: Linux 3.4.x
ROM Firmware Required: CM11
Based On: CyanogenMod
Version Information
Status: Testing
Current Beta Version: 0.1
Beta Release Date: 2015-06-09
Created 2015-06-10
Last Updated 2015-07-08
WooHoo!
hotwired34 said:
WooHoo!
Click to expand...
Click to collapse
FYI: I just updated the kernel zip to fix approximately everything.
I am trying to make a port for cm12.1 d2att could you upload the device scripts.
aron2hip said:
I am trying to make a port for cm12.1 d2att could you upload the device scripts.
Click to expand...
Click to collapse
Uhhh....
Not that easy...
Also ask on the d2att thread.
dank101 said:
Uhhh....
Not that easy...
Also ask on the d2att thread.
Click to expand...
Click to collapse
I have the kernel source in the devices directory, I'm just too lazy to edit the androidmenu bash script for the device. Unless there are further modifications necessary.
Sent from my SAMSUNG-SGH-I747 using Tapatalk
aron2hip said:
I have the kernel source in the devices directory, I'm just too lazy to edit the androidmenu bash script for the device. Unless there are further modifications necessary.
Sent from my SAMSUNG-SGH-I747 using Tapatalk
Click to expand...
Click to collapse
There are indeed future mods needed.
The first two Google Drive links are dead.
Here is a mirror for the files. I don't know how long they will last so urge OP for new mirror.
http://www.filedropper.com/kalilinuxnethunter121d2ltekitkat
946mb
http://www.filedropper.com/kalinhkernel
12.5mb
Knuxyl said:
The first two Google Drive links are dead.
Here is a mirror for the files. I don't know how long they will last so urge OP for new mirror.
http://www.filedropper.com/kalilinuxnethunter121d2ltekitkat
946mb
http://www.filedropper.com/kalinhkernel
12.5mb
Click to expand...
Click to collapse
You really should have PMed me about this FIRST.
I didn't know they died.
When will file links be available for download again cause? I was only ever able to download the kali kernel!
Flashed cm11 plus all zips , rom boots fine. Except for the part where the screen doesn't display anything (stays blank and off), however I can swipe to unlock and get the vibration as well as turn the volume up and down and get the sound that is associated. Any ideas I've done it twice with full wipes of everything I could wipe asside from the sd card
balves08 said:
Flashed cm11 plus all zips , rom boots fine. Except for the part where the screen doesn't display anything (stays blank and off), however I can swipe to unlock and get the vibration as well as turn the volume up and down and get the sound that is associated. Any ideas I've done it twice with full wipes of everything I could wipe asside from the sd card
Click to expand...
Click to collapse
You're doing it wrong.
You don't wipe anything.
dank101 said:
You're doing it wrong.
You don't wipe anything.
Click to expand...
Click to collapse
Im not wiping between installing cm11 and the two zips, that's stupidity. I was doing a full wipe before reflashing cm11 and the 2 zips again. Just no display
balves08 said:
Im not wiping between installing cm11 and the two zips, that's stupidity. I was doing a full wipe before reflashing cm11 and the 2 zips again. Just no display
Click to expand...
Click to collapse
I don't understand how that could be happening....
It's working on my S3 fine. And the nethunter zips are just a kernel and a zip that runs a bunch of scripts and extracts a CHROOT.
dank101 said:
I don't understand how that could be happening....
It's working on my S3 fine. And the nethunter zips are just a kernel and a zip that runs a bunch of scripts and extracts a CHROOT.
Click to expand...
Click to collapse
Do you think that it would have anything to do with what version of cm11 that is being used, I r what baseband? (I'm noob ish when it comes to that) cuz cm11 works fine then I flash everything and it shows the Droid logo or w/e and then goes blank with the soft keys illuminating, as well as responding to touch (side note I had forgotten to authenticate the adb connection prior so I could easily reboot to recovery and was able to bring up and select ok to allow it w/o the screen being visible, so it must be something driver related to the display)
balves08 said:
Do you think that it would have anything to do with what version of cm11 that is being used, I r what baseband? (I'm noob ish when it comes to that) cuz cm11 works fine then I flash everything and it shows the Droid logo or w/e and then goes blank with the soft keys illuminating, as well as responding to touch (side note I had forgotten to authenticate the adb connection prior so I could easily reboot to recovery and was able to bring up and select ok to allow it w/o the screen being visible, so it must be something driver related to the display)
Click to expand...
Click to collapse
Try flashing CM11 without flashing nethunter, if the display is working, then I dunno what to say.
dank101 said:
Try flashing CM11 without flashing nethunter, if the display is working, then I dunno what to say.
Click to expand...
Click to collapse
Done that 3 times cm11 works fine, display goes to **** after flashing nethunter. What version of cm11 are you using by the way
Clean flash over 04/26 nightly took about 20 mins. No issues so far I got some more playing around to do before a final verdict. Thanks I'll have some fun with this.
balves08 said:
Done that 3 times cm11 works fine, display goes to **** after flashing nethunter. What version of cm11 are you using by the way
Click to expand...
Click to collapse
Personally I used the d2lte latest nightly.
What good is this to the S3? I wasn't aware that this phone can go into monitor mode at all.