[Q] RUU problem - HTC One X

Hey! I screwed up my root on my One X and now I am trying to apply an RUU update.
I downloaded the latest one I could find on androidruu.com
When it was about halfway done it aborted automatically and I got this message:
ERROR [158]: IMAGE ERROR
The ROM Update Utility cannot update your Android phone.
Please get the correct ROM Update Utility and try again.
My current version is 4.18.771.4 and it wanted to update/downgrade to 3.14.401.31 which is nowhere near my current version so the RUU must be wrong?
It said it was released 2013-01-30 15:48:53 and that's the latest one on that website, maybe there are other websites with more recent RUUs?
Here is also my "getvar" info
version: 0.5a
version-bootloader: 1.72.0000
version-baseband: 5.1204.167.31H
version-cpld: None
version-microp: None
version-main: 4.18.771.4
serialno: ************
imei: ***************
product: endeavoru
platform: HBOOT-T30S
modelid: PJ4610000
cidnum: H3G__G04
battery-status: good
battery-voltage: 3765mV
devpower: 39
partition-layout: None
security: on
build-mode: SHIP
boot-mode: FASTBOOT
commitno-bootloader: None
hbootpreupdate: 2
gencheckpt: 0
Please ask if you need more information!

KakisHLoLz said:
Hey! I screwed up my root on my One X and now I am trying to apply an RUU update.
I downloaded the latest one I could find on androidruu.com
When it was about halfway done it aborted automatically and I got this message:
ERROR [158]: IMAGE ERROR
The ROM Update Utility cannot update your Android phone.
Please get the correct ROM Update Utility and try again.
My current version is 4.18.771.4 and it wanted to update/downgrade to 3.14.401.31 which is nowhere near my current version so the RUU must be wrong?
It said it was released 2013-01-30 15:48:53 and that's the latest one on that website, maybe there are other websites with more recent RUUs?
Here is also my "getvar" info
version: 0.5a
version-bootloader: 1.72.0000
version-baseband: 5.1204.167.31H
version-cpld: None
version-microp: None
version-main: 4.18.771.4
serialno: ************
imei: ***************
product: endeavoru
platform: HBOOT-T30S
modelid: PJ4610000
cidnum: H3G__G04
battery-status: good
battery-voltage: 3765mV
devpower: 39
partition-layout: None
security: on
build-mode: SHIP
boot-mode: FASTBOOT
commitno-bootloader: None
hbootpreupdate: 2
gencheckpt: 0
Please ask if you need more information!
Click to expand...
Click to collapse
You are S-ON you can't downgread from 4.18 to 3.14 you can use only nandroid backup to restore stock rom or flash custom

You can,only use the ruu for your main version/cid
Gesendet von meinem HTC One X mit Tapatalk
---------- Post added at 06:38 PM ---------- Previous post was at 06:38 PM ----------
Why or unlocking bootloader flash a custom recovery and a custom Rom...
Gesendet von meinem HTC One X mit Tapatalk

KakisHLoLz said:
version-bootloader: 1.72.0000
Click to expand...
Click to collapse
RUU will not work on HBOOT above 1.39

meat_hooligan said:
RUU will not work on HBOOT above 1.39
Click to expand...
Click to collapse
Yes it will, if you manage to get your hands on a 4.18 ruu

Thant said:
You are S-ON you can't downgread from 4.18 to 3.14 you can use only nandroid backup to restore stock rom or flash custom
Click to expand...
Click to collapse
The problem is that I can not boot into OS.
I am stuck on the Cyanogenmod boot logo.
I don't know what went wrong, I unlocked the device and flashed with TWRP.
Then I got the problem where the touch did not work so I had to flash an older version of TWRP which fixed that.
Then I flashed my Cyanogenmod ROM and wiped both the dalvik and regular cache.
When I tried to boot it just stuck on the boot logo.
I tried to wipe the data but I managed to somehow mix up two different wipe options and obviously I wiped both the backup and everything on my sdcard. I'm screwed...
I used the adb tool to push over Cyanogenmod to TWRP and flashed the ROM ones again to see if that might fix the problem.
I still couldn't boot into OS and so I tried to follow Cyanogenmod's guide on how to root One X.
I flashed the recovery with Clockwork recovery and everything went fine until I try to flash a ROM from Clockwork recovery... I can't mount my sdcard?!?!
I tried to flash back to TWRP but when I try to boot into recovery from bootloader it just reboots back into HBOOT...
So now here I sit and think how much life sucks.

I never see you mentioning flashing the boot.img from CM ?
But if you start to flash this recovery
https://www.dropbox.com/s/yqzlpqo8illa53j/Philz recovery 5.15.9.img
It has touch and you can also mount the sdcard

Mr Hofs said:
Yes it will, if you manage to get your hands on a 4.18 ruu
Click to expand...
Click to collapse
I think RUU 4.18 will not

meat_hooligan said:
I think RUU 4.18 will not
Click to expand...
Click to collapse
I know its not available, but i am just saying......if it would be then it would work

Mr Hofs said:
I never see you mentioning flashing the boot.img from CM ?
But if you start to flash this recovery
It has touch and you can also mount the sdcard
Click to expand...
Click to collapse
My phone is currently charging, I will try to flash that file as soon as the battery is high enough

KakisHLoLz said:
My phone is currently charging, I will try to flash that file as soon as the battery is high enough
Click to expand...
Click to collapse
Take Action

meat_hooligan said:
Take Action
Click to expand...
Click to collapse
It seems that my phone won't charge, it's been charging for 4hr+ and it still says too low to flash...

Mr Hofs said:
I never see you mentioning flashing the boot.img from CM ?
But if you start to flash this recovery
It has touch and you can also mount the sdcard
Click to expand...
Click to collapse
Okay so I managed to flash PhilZ Touch 5, now you say I should flash boot.img, is that the file inside the cyanogenmod zip or is it a separate download?

I got everything to work, I flashed the boot.img and I am now a happy owner of a rooted One X
Thanks for your help! Cred to Mr Hofs!

Nice !
CASE CLOSED !

Related

Problems during restoring phone

Hi everyone,
I'm stuck, I am trying to restore my HTC One X to stock as I am sending off for repair, however its not working. I've read many tutorials but I'm still not getting anywhere.
I've locked the phone, replaced the recovery.img and replaced the boot.img however the RUU won't install.
My phone is from Australia, Virgin and has the CID of: CID_023
My original Nandroid back-up is gone, so I can't use that.
Can anyone give me some advice on what I might be doing wrong and what information you require to help me?
S-ON
HBOOT-1.39.0000
FabMan_UK said:
Hi everyone,
I'm stuck, I am trying to restore my HTC One X to stock as I am sending off for repair, however its not working. I've read many tutorials but I'm still not getting anywhere.
I've locked the phone, replaced the recovery.img and replaced the boot.img however the RUU won't install.
My phone is from Australia, Virgin and has the CID of: CID_023
My original Nandroid back-up is gone, so I can't use that.
Can anyone give me some advice on what I might be doing wrong and what information you require to help me?
S-ON
HBOOT-1.39.0000
Click to expand...
Click to collapse
Post the result from command fastboot getvar all and delete your S/N and IMEI from the info
Thant said:
Post the result from command fastboot getvar all and delete your S/N and IMEI from the info
Click to expand...
Click to collapse
version: 0.5a
version-bootloader: 1.39.0000
version-baseband: 5.1204.162.29
version-cpld: None
version-microp: None
version-main: 3.17.728.1
serialno:
imei:
product: endeavoru
platform: HBOOT-T30S
modelid: PJ4611000
cidnum: HTC__023
battery-status: good
battery-voltage: 4157mV
devpower: 100
partition-layout: None
security: on
build-mode: SHIP
boot-mode: FASTBOOT
commitno-bootloader: None
hbootpreupdate: 2
gencheckpt: 0
Thanks
FabMan_UK said:
version: 0.5a
version-bootloader: 1.39.0000
version-baseband: 5.1204.162.29
version-cpld: None
version-microp: None
version-main: 3.17.728.1
serialno:
imei:
product: endeavoru
platform: HBOOT-T30S
modelid: PJ4611000
cidnum: HTC__023
battery-status: good
battery-voltage: 4157mV
devpower: 100
partition-layout: None
security: on
build-mode: SHIP
boot-mode: FASTBOOT
commitno-bootloader: None
hbootpreupdate: 2
gencheckpt: 0
Thanks
Click to expand...
Click to collapse
You must to restore nandroid backup no RRU for nwer base more then 3.14. NOW
1. Install this recovery with command fastboot flash recovery recovery.img
2. download this Nandroid Backup
3. go in recovery mount the sd card and unrar the nandroid backup to your computer after this paste on your SD card in folder Backup
4. flash the boot.img, erase cache, and restor nandroid from recovery.
5. You must to install stock recovery and you are full stock and you can receive OTA
Thant said:
You must to restore nandroid backup no RRU for nwer base more then 3.14. NOW
1. Install this recovery with command fastboot flash recovery recovery.img
2. download this Nandroid Backup
3. go in recovery mount the sd card and unrar the nandroid backup to your computer after this paste on your SD card in folder Backup
4. flash the boot.img, erase cache, and restor nandroid from recovery.
5. You must to install stock recovery and you are full stock and you can receive OTA
Click to expand...
Click to collapse
Thank you for your help, so the problem for me was the 3.14 update I had applied. I can't download the file at work, I'll try at home later.
Thant, I want to thank you for your assistance with this problem. Your solution worked, I was able to install the OTA update.
The guides I was following used the RUU as the solution to those without a working Nandroid back up of their own, I wasn't aware that 3.14 or newer could be a problem for that. It is a shame out of date guides are not removed or updated.
I had seen people upload nandroid backups, but I didn't trust those. I decided to take a chance with yours and it worked for me.
My info now states:
version: 0.5a
version-bootloader: 1.73.0000
version-baseband: 5.1204.167.31
version-cpld: None
version-microp: None
version-main: 4.19.728.3
serialno:
imei:
product: endeavoru
platform: HBOOT-T30S
modelid: PJ4611000
cidnum: HTC__023
battery-status: good
battery-voltage: 4061mV
devpower: 97
partition-layout: None
security: on
build-mode: SHIP
boot-mode: FASTBOOT
commitno-bootloader: None
hbootpreupdate: 2
gencheckpt: 0
SuperSU is still install, I am now assuming the firmware/h-boot is still a modified version. Looking into it.
Thant said:
You must to restore nandroid backup no RRU for nwer base more then 3.14. NOW
1. Install this recovery with command fastboot flash recovery recovery.img
2. download this Nandroid Backup
3. go in recovery mount the sd card and unrar the nandroid backup to your computer after this paste on your SD card in folder Backup
4. flash the boot.img, erase cache, and restor nandroid from recovery.
5. You must to install stock recovery and you are full stock and you can receive OTA
Click to expand...
Click to collapse
Okay I'm going crazy SuperSU is on my phone and I can't get rid of it. I couldn't uninstall it, so I re-rooted the phone, installed custom recovery, installed SuperSU binaries then tried to uninstall. But every reboot reinstalls the application. Argh!!!
Any help with this?
Okay fixed the SuperSU problem, unfortunately the Nadroid backup supplied was not a stock image, still worked though when I did a factory reset, restored nandroid backup, install SU binaries, uninstalled SuperSU from OS, restored recovery, locked OEM, downloaded OTA and installed it.
So it all looks good except the recovery option comes up with an image of a phone and a large red exclamation mark, I assume this means the recovery.img doesn't match. Is there a way to fix this as I'd like my phone repaired?
Thank you
-EDIT-
Okay, I've done some more reading and learnt a little more, which is great.
I believe I need recovery.img for 4.19.728.3, so that will match the software on my phone. I've tried stock recovery for 4.19.707.3 but that didn't work.
I wonder if I should downgrade everything. Say downgrade HBOOT to 1.39, then install stock software of 4.18 and removing SuperSU, then flash stock recovery, lock the phone and attempt a OTA update to update everything. I'm assuming an OTA update would update HBOOT to 1.73, the software to 4.19 and the recovery will also be updated to work. Is this a good solution perhaps?
FabMan_UK said:
Okay I'm going crazy SuperSU is on my phone and I can't get rid of it. I couldn't uninstall it, so I re-rooted the phone, installed custom recovery, installed SuperSU binaries then tried to uninstall. But every reboot reinstalls the application. Argh!!!
Any help with this?
Okay fixed the SuperSU problem, unfortunately the Nadroid backup supplied was not a stock image, still worked though when I did a factory reset, restored nandroid backup, install SU binaries, uninstalled SuperSU from OS, restored recovery, locked OEM, downloaded OTA and installed it.
So it all looks good except the recovery option comes up with an image of a phone and a large red exclamation mark, I assume this means the recovery.img doesn't match. Is there a way to fix this as I'd like my phone repaired?
Thank you
-EDIT-
Okay, I've done some more reading and learnt a little more, which is great.
I believe I need recovery.img for 4.19.728.3, so that will match the software on my phone. I've tried stock recovery for 4.19.707.3 but that didn't work.
I wonder if I should downgrade everything. Say downgrade HBOOT to 1.39, then install stock software of 4.18 and removing SuperSU, then flash stock recovery, lock the phone and attempt a OTA update to update everything. I'm assuming an OTA update would update HBOOT to 1.73, the software to 4.19 and the recovery will also be updated to work. Is this a good solution perhaps?
Click to expand...
Click to collapse
You can't downgrade are you upgrade the stock rom to 4.19?
if you are on 3.17.728.x you need stock rom not rooted and stock recovery 3.17.728.x maybe you can try with stock recovery 4.19.728.x
Thant said:
You can't downgrade are you upgrade the stock rom to 4.19?
Click to expand...
Click to collapse
Yes, I upgraded stock ROM to 4.19.
Thant said:
maybe you can try with stock recovery 4.19.728.x
Click to expand...
Click to collapse
That would be great, a Google search doesn't show anything and neither does a search on XDA forums, would you have any suggestions where I could find it?
Thanks

Cannot flash custom rom, but why ?

Hey there,
i have a strage problem, after rooting a lot of android devices the m8 behaves kind of strange.
I got a brand new M8 (Hbot 3.15xxxx and 4.4.2) for my girl friend and unlocked the device with htc dev. after this i flashed twrp 2.7.0.2, no big deal.
Now i made a backup (thank god....) and downloaded viper rom and arhd roms.
But if i install a rom (does not matter which one, with wipe and so on) the script tells me installtion is finished, but if i hit the next button the m8 vibrates and turns off, at least the screen goes dark.
the only way to wake up the m8 is to push power and volume up button, but the only thing i see is the htc logo with the red text at the buttom.
adb reboot boatloader does not work, but reboot recocery does. Wipen cache and so does not fix the problem, the stock backup can be restored.
do you have any idea what's going on, i really want to run viper or arhd on the m8.
thanks!
Havoc2k said:
Hey there,
i have a strage problem, after rooting a lot of android devices the m8 behaves kind of strange.
I got a brand new M8 (Hbot 3.15xxxx and 4.4.2) for my girl friend and unlocked the device with htc dev. after this i flashed twrp 2.7.0.2, no big deal.
Now i made a backup (thank god....) and downloaded viper rom and arhd roms.
But if i install a rom (does not matter which one, with wipe and so on) the script tells me installtion is finished, but if i hit the next button the m8 vibrates and turns off, at least the screen goes dark.
the only way to wake up the m8 is to push power and volume up button, but the only thing i see is the htc logo with the red text at the buttom.
adb reboot boatloader does not work, but reboot recocery does. Wipen cache and so does not fix the problem, the stock backup can be restored.
do you have any idea what's going on, i really want to run viper or arhd on the m8.
thanks!
Click to expand...
Click to collapse
Just a bug in TWRP, nothing to worry about. Disable from TWRP the screen timeout and you are good to go.
stathis95194 said:
Just a bug in TWRP, nothing to worry about. Disable from TWRP the screen timeout and you are good to go.
Click to expand...
Click to collapse
i don't think thats the problem. if the screen would timeout (like while doing backup or restore) i could wake it up.
but the device is not booting anymore then. Even if i do a adb reboot recovery and make a clean reboot. Just the htc logo with the warning.
could it be the firmware ? i dont see any information for hboot 3.15.....
thanks
Havoc2k said:
i don't think thats the problem. if the screen would timeout (like while doing backup or restore) i could wake it up.
but the device is not booting anymore then. Even if i do a adb reboot recovery and make a clean reboot. Just the htc logo with the warning.
could it be the firmware ? i dont see any information for hboot 3.15.....
thanks
Click to expand...
Click to collapse
Are you flashing a 4.4.3 ROM? which firmware are you on? Can you please do a :
fastboot getvar all
and post the outcome? Don't forget to hide your sensitive info (imei, etc)
stathis95194 said:
Are you flashing a 4.4.3 ROM? which firmware are you on? Can you please do a :
fastboot getvar all
and post the outcome? Don't forget to hide your sensitive info (imei, etc)
Click to expand...
Click to collapse
yes i will flash viper 2.0.0 or arhd 10.2 both are 4.4.3 roms.
device is running at 4.4.2 at the moment (rooted stock vodafone germany)
getvar all:
Code:
version: 0.5
version-bootloader: 3.16.0.0000
version-baseband: 1.15.2133156.UA03_2G
version-cpld: None
version-microp: None
version-main:
version-misc: PVT SHIP S-ON
serialno: HT43FWM10422
imei: xxxxxxxxx
imei2: Not Support
meid: 00000000000000
product: m8_ul
platform: hTCBmsm8974
modelid: 0P6B10000
cidnum: T-MOB101
battery-status: good
battery-voltage: 0mV
partition-layout: Generic
security: on
build-mode: SHIP
boot-mode: FASTBOOT
commitno-bootloader: 0a41237a
hbootpreupdate: 11
gencheckpt: 0
m8_ul...... what device is it? internation one? should be, there are no at&t or sprint devices in germany, are they?
edit: i think i found the problem:
ckpv5 said:
Right ... your current hboot is 3.16 so it's 1.54.707.7
I suggest that you restore 1.54.707.7 stock Backup, flash back stock recovery and do the OTA (no need to relock bootloader or S-On .. OTA update work on unlocked bootloader and S-Off)
Click to expand...
Click to collapse
so the firmware should be the problem, i am right?
Havoc2k said:
yes i will flash viper 2.0.0 or arhd 10.2 both are 4.4.3 roms.
device is running at 4.4.2 at the moment (rooted stock vodafone germany)
getvar all:
Code:
version: 0.5
version-bootloader: 3.16.0.0000
version-baseband: 1.15.2133156.UA03_2G
version-cpld: None
version-microp: None
version-main:
version-misc: PVT SHIP S-ON
serialno: HT43FWM10422
imei: xxxxxxxxx
imei2: Not Support
meid: 00000000000000
product: m8_ul
platform: hTCBmsm8974
modelid: 0P6B10000
cidnum: T-MOB101
battery-status: good
battery-voltage: 0mV
partition-layout: Generic
security: on
build-mode: SHIP
boot-mode: FASTBOOT
commitno-bootloader: 0a41237a
hbootpreupdate: 11
gencheckpt: 0
m8_ul...... what device is it? internation one? should be, there are no at&t or sprint devices in germany, are they?
Click to expand...
Click to collapse
Well nothing strange here. You are on older firmware trying to flash a 4.4.3 ROM. First boot might take up to 15 minutes...But after that you will experience slow boots and/or wifi or bt issues.
You can either try to s-off and upgrade firmware or try a 4.4.2 rom like ARHD 8.1
First of all try the following. Flash the ROM and reboot and let it sit there for around 15 minutes to see if it boots. And we can see your choices from there.
If i want to update with OTA,
which stock recovery i need to flash ? my version.main is empty :/ so i am not sure how to flash the right recovery. there a lots of them: http://forum.xda-developers.com/showthread.php?t=2701376
Havoc2k said:
If i want to update with OTA,
which stock recovery i need to flash ? my version.main is empty :/ so i am not sure how to flash the right recovery. there a lots of them: http://forum.xda-developers.com/showthread.php?t=2701376
Click to expand...
Click to collapse
Try here:
http://www.handy-faq.de/forum/htc_o...resammlung_ruus_otas_backups.html#post2832637
it's either 1.12.111.18 or 1.57.111.2
it is 1.12.111.18
at the moment the OTA to 1.57.111.2 is running
some german forums wrote that any 1.12.xxx recovery will work for the ota. let's see if there is another ota after this one.
edit: 1.57 went well, now ota to 1.70

[Q] Pls help - HTC One X stuck on quietly brilliant screen and won't restore

Hi Friends,
First things first - I have looked up and tried several things that other folks facing similar issues have tried. None of it has worked for me.
Coming to the problem now.
It all began when I decided to unroot and install a custom ROM on my stock HTC One X and downloaded a stable build from http://wiki.cyanogenmod.org/w/Install_CM_for_endeavoru.
I followed the tutorials and unlocked my device and started off with CWM recovery 5.8.2.7. Did some experiemenation with backup and recovery. So far, so good.
I decided to use the 4.4 ROM and as per some information available it needed me to update to CWM 6.0.4.8. I did so but when I tried to go in recovery, the screen went blank. Tried it multiple times without luck.
Then I switched over to TWRP 2.7.1 and used it to install the cm-11-20141112-SNAPSHOT-M12-endeavoru.zip. It failed with status 7. Assert checks on bootloader ver failed (as per checks it would need anything 1.28 or higher). I am on hboot 1.12. I extracted the boot.img from the rom zip and flashed it from fastboot. It showed no change in hboot version (maybe this is where I faulted). It still won't install rom zip as I would expect.
Now the phone won't go beyond "Quietly Brilliant" screen on power on. Recovery to saved backup says its successful but it still gets stuck at same screen on reboot.
Would appreciate help and pointers from anyone who could help.
Thanks in advance,
Kunal
koolvirgo said:
Hi Friends,
First things first - I have looked up and tried several things that other folks facing similar issues have tried. None of it has worked for me.
Coming to the problem now.
It all began when I decided to unroot and install a custom ROM on my stock HTC One X and downloaded a stable build from http://wiki.cyanogenmod.org/w/Install_CM_for_endeavoru.
I followed the tutorials and unlocked my device and started off with CWM recovery 5.8.2.7. Did some experiemenation with backup and recovery. So far, so good.
I decided to use the 4.4 ROM and as per some information available it needed me to update to CWM 6.0.4.8. I did so but when I tried to go in recovery, the screen went blank. Tried it multiple times without luck.
Then I switched over to TWRP 2.7.1 and used it to install the cm-11-20141112-SNAPSHOT-M12-endeavoru.zip. It failed with status 7. Assert checks on bootloader ver failed (as per checks it would need anything 1.28 or higher). I am on hboot 1.12. I extracted the boot.img from the rom zip and flashed it from fastboot. It showed no change in hboot version (maybe this is where I faulted). It still won't install rom zip as I would expect.
Now the phone won't go beyond "Quietly Brilliant" screen on power on. Recovery to saved backup says its successful but it still gets stuck at same screen on reboot.
Would appreciate help and pointers from anyone who could help.
Thanks in advance,
Kunal
Click to expand...
Click to collapse
give me the result from command fastboot getvar version-main. And after this we will see haow to upgrade your hboot you are with too low hboot version
Thant said:
give me the result from command fastboot getvar version-main. And after this we will see haow to upgrade your hboot you are with too low hboot version
Click to expand...
Click to collapse
Hi,
Thanks pal ! Here is the output of fastboot getvar version-main
version-main: 0.0.0.178434
thanks,
Kunal
Ok.....so as I mentioned in my first post, I did play around with CWM 5.8.2.7 at the beginning and had made a backup. So I flashed CWM again and was able to restore my device.
Now, I need to update to CM11 ROM and would need help with that please. I guess what I already have is there in the first post I put in this thread. Here's the dump of fastboot getvar all
(bootloader) version: 0.5a
(bootloader) version-bootloader: 1.12.2000
(bootloader) version-baseband: 2.1204.135.20
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 0.0.0.178434
(bootloader) serialno: HT22WW100191
(bootloader) imei: 3591*********75
(bootloader) product: endeavoru
(bootloader) platform: HBOOT-T30S
(bootloader) modelid: PJ461****
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 4217mV
(bootloader) devpower: 100
(bootloader) partition-layout: None
(bootloader) security: off
(bootloader) build-mode: ENG
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: None
(bootloader) hbootpreupdate: 2
(bootloader) gencheckpt: 0
thanks again in advance,
Kunal
koolvirgo said:
Ok.....so as I mentioned in my first post, I did play around with CWM 5.8.2.7 at the beginning and had made a backup. So I flashed CWM again and was able to restore my device.
Now, I need to update to CM11 ROM and would need help with that please. I guess what I already have is there in the first post I put in this thread. Here's the dump of fastboot getvar all
(bootloader) version: 0.5a
(bootloader) version-bootloader: 1.12.2000
(bootloader) version-baseband: 2.1204.135.20
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 0.0.0.178434
(bootloader) serialno: HT22WW100191
(bootloader) imei: 3591*********75
(bootloader) product: endeavoru
(bootloader) platform: HBOOT-T30S
(bootloader) modelid: PJ461****
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 4217mV
(bootloader) devpower: 100
(bootloader) partition-layout: None
(bootloader) security: off
(bootloader) build-mode: ENG
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: None
(bootloader) hbootpreupdate: 2
(bootloader) gencheckpt: 0
thanks again in advance,
Kunal
Click to expand...
Click to collapse
No problem you are S-OFF Download this RUU relock your bootloader or if it's locked leave it locked and run the RUU this will upgrade your phone to 3.14.401.31 then upgrade to latest 4.18.401.4 after this you can unlock the bootloader and flash custom recovery latest TWRP or CWM or Philz and flash what you want
Thant said:
No problem you are S-OFF Download this RUU relock your bootloader or if it's locked leave it locked and run the RUU this will upgrade your phone to 3.14.401.31 then upgrade to latest 4.18.401.4 after this you can unlock the bootloader and flash custom recovery latest TWRP or CWM or Philz and flash what you want
Click to expand...
Click to collapse
Hi Thant,
Thanks for your tip. I will give this a try (though I will be able to try it out someone later this week only and provide update how it went).
Having said that, I have one question though - the link to RUU you specified looks like for unlocked HTC Europe version. I'm from India and I found that there might be one with same radio for India here.
Not doubting your advice, but just want to know what is the basis for knowing what RUU one must use ?
Also, can I choose the one for India (RUU_ENDEAVOR_U_JB_45_S_hTC_Asia_India_3.14.720.24_Radio_5.1204.162.29) ?
thanks,
Kunal
koolvirgo said:
Hi Thant,
Thanks for your tip. I will give this a try (though I will be able to try it out someone later this week only and provide update how it went).
Having said that, I have one question though - the link to RUU you specified looks like for unlocked HTC Europe version. I'm from India and I found that there might be one with same radio for India here.
Not doubting your advice, but just want to know what is the basis for knowing what RUU one must use ?
Also, can I choose the one for India (RUU_ENDEAVOR_U_JB_45_S_hTC_Asia_India_3.14.720.24_Radio_5.1204.162.29) ?
thanks,
Kunal
Click to expand...
Click to collapse
yes if you want, most of the people like European version not Asian. It is your choice you are S-OFF and you can flash what you want on your phone. And the radio is the same
Thant said:
yes if you want, most of the people like European version not Asian. It is your choice you are S-OFF and you can flash what you want on your phone. And the radio is the same
Click to expand...
Click to collapse
Hi Thant,
I did try the RUU you told me to use but update failed with error 159.
There are some RUUs for Indian models at http://www.androidruu.com/?developer=Endeavor and http://forum.xda-developers.com/showthread.php?t=2189048 but none for JB.
I have provided the getvar dump earlier but can't seem to find what I need to use (sorry for being a noob here). Please suggest what I can do more.
Merry Christmas and a Happy New Year.
thanks,
Kunal
koolvirgo said:
Hi Thant,
I did try the RUU you told me to use but update failed with error 159.
There are some RUUs for Indian models at http://www.androidruu.com/?developer=Endeavor and http://forum.xda-developers.com/showthread.php?t=2189048 but none for JB.
I have provided the getvar dump earlier but can't seem to find what I need to use (sorry for being a noob here). Please suggest what I can do more.
Merry Christmas and a Happy New Year.
thanks,
Kunal
Click to expand...
Click to collapse
are you charge your phone before run the RUU are you reloack the bootloader before run the RUU???
Thant said:
are you charge your phone before run the RUU are you reloack the bootloader before run the RUU???
Click to expand...
Click to collapse
Yes, I did both !!
koolvirgo said:
Yes, I did both !!
Click to expand...
Click to collapse
Are your phone say Endeavoru PVT in bootloader or say Endeavoru XE?
I have the same issue, I used the WinDroid toolkit but somehow I got stuck in the boot. I can go in recovery. My phone says endeavoru pvt. I also have the S-on.
INFOversion: 0.5a
INFOversion-bootloader: 1.72.0000
INFOversion-baseband: 5.1204.167.31
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 4.18.401.4
INFOserialno: HT23NW107620
INFOimei: 359188041361783
INFOproduct: endeavoru
INFOplatform: HBOOT-T30S
INFOmodelid: PJ4610000
INFOcidnum: HTC__405
INFObattery-status: good
INFObattery-voltage: 3660mV
INFOdevpower: 3
INFOpartition-layout: None
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: None
INFOhbootpreupdate: 2
INFOgencheckpt: 0
Click to expand...
Click to collapse
What I have to do?? Thanks for the help you are saving me!!
lollerz46 said:
I have the same issue, I used the WinDroid toolkit but somehow I got stuck in the boot. I can go in recovery. My phone says endeavoru pvt. I also have the S-on.
What I have to do?? Thanks for the help you are saving me!!
Click to expand...
Click to collapse
Okay I solved my problem, my issue was the boot.img that was different from the one inside the custom rom! Hope this helps
Thant said:
Are your phone say Endeavoru PVT in bootloader or say Endeavoru XE?
Click to expand...
Click to collapse
It says Endeavoru XE
koolvirgo said:
It says Endeavoru XE
Click to expand...
Click to collapse
Than this is bad news try to download ICS Asian RUU and restore it, then try to update to latest Asian rom if this not work you maust to update your hboot manualy the XE variant have a lot of problems with the update but first try to run ICS Asian RUU then check for update and then update Try this RUU
Thant said:
Than this is bad news try to download ICS Asian RUU and restore it, then try to update to latest Asian rom if this not work you maust to update your hboot manualy the XE variant have a lot of problems with the update but first try to run ICS Asian RUU then check for update and then update Try this RUU
Click to expand...
Click to collapse
Hi Thant,
I have not yet tried tried the ICS RUU you suggested. But before I go ahead, here's some more info.
The Android version, HTC Sense version both say "Protected"
Software number is "Unknown"
HTC SDK API level is 4.23
Kernel is 2.6.39.4-g7ecc196
Baseband version is 2.1204.135.20
Build no. is 0.1.0.0 (20130509 EndeavorU_Generic_WWE#178434)
Boot loader says -
ENDEAVORU XE ENG S-OFF RH
CID-11111111
HBOOT- 1.12.2000 (PJ461****)
CPLD-None
MICROP-None
RADIO-2.1204.135.20
Now, should I go ahead with the ICS RUU ?
How do I know what Android version I'm on ? Why would it say protected ? Any command I can fire from fastboot/adb ?
[getvar says (bootloader) version-main: 0.0.0.178434]
Thanks for all your time & help,
Kunal
koolvirgo said:
Hi Thant,
I have not yet tried tried the ICS RUU you suggested. But before I go ahead, here's some more info.
The Android version, HTC Sense version both say "Protected"
Software number is "Unknown"
HTC SDK API level is 4.23
Kernel is 2.6.39.4-g7ecc196
Baseband version is 2.1204.135.20
Build no. is 0.1.0.0 (20130509 EndeavorU_Generic_WWE#178434)
Boot loader says -
ENDEAVORU XE ENG S-OFF RH
CID-11111111
HBOOT- 1.12.2000 (PJ461****)
CPLD-None
MICROP-None
RADIO-2.1204.135.20
Now, should I go ahead with the ICS RUU ?
How do I know what Android version I'm on ? Why would it say protected ? Any command I can fire from fastboot/adb ?
[getvar says (bootloader) version-main: 0.0.0.178434]
Thanks for all your time & help,
Kunal
Click to expand...
Click to collapse
You are S-OFF you can run any RUU but your problem is that your phone say XE not PVT the XE edition have problem with the update hboot
Thant said:
You are S-OFF you can run any RUU but your problem is that your phone say XE not PVT the XE edition have problem with the update hboot
Click to expand...
Click to collapse
Hi Thant,
I tried it and failed Needless to say I made sure all the prerequisites were met.
Can you please tell me how to manually update hboot ?
thanks,
Kunal
koolvirgo said:
Hi Thant,
I tried it and failed Needless to say I made sure all the prerequisites were met.
Can you please tell me how to manually update hboot ?
thanks,
Kunal
Click to expand...
Click to collapse
fastboot oem lock - relock the bootloader
fastboot oem rebootRUU
fastboot flash zip firmware.zip
fastboot flash zip firmware.zip (AGAIN)
fastboot reboot-bootloader
fastboot flash unlocktoken Unlock_code.bin
then like normal flash recovery and then rom
You can find firmware.zip from OTA on the page with the RUU choice one OTA and flash it try with this one in attachment
Thant said:
fastboot oem lock - relock the bootloader
fastboot oem rebootRUU
fastboot flash zip firmware.zip
fastboot flash zip firmware.zip (AGAIN)
fastboot reboot-bootloader
fastboot flash unlocktoken Unlock_code.bin
then like normal flash recovery and then rom
You can find firmware.zip from OTA on the page with the RUU choice one OTA and flash it try with this one in attachment
Click to expand...
Click to collapse
Hi Thant,
Before trying what you suggested (for manual update) I tried the ICS RUU once again. It went through fine this time not sure why, then I did an OTA upgrade and now I'm on Android 4.0.4 hboot 1.12 (same as before but on 2.17.720.2). There are no more OTA updates available, though HTC india website says there is one available for 3.14.720.24 which is JB version and should automatically update my hboot which I can then hopefully use to update to 4.4 ROM. Do you think what I think is going to work ?
But I can't find the OTA firmware for 3.14.720.24. There was one available here but no more.
There's one here but not sure about the authenticity of this.
I have downloaded the firmware zip you shared but it seems the file is corrupt.
Thanks,
Kunal

Custom ROM causes boot loop

OK here is the situation - I have Sense 6/Lolipop 5.0.1 stock ROM( installed via OTA update) on the phone which works.
I have got root and got latest SuperSU and TWRP installed.
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.26.21331147A1.16G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno: zzzzzzzzzzz
(bootloader) imei: xxxxxxxxxxxxxxxxx
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B11000
(bootloader) cidnum: HTC__039
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: ba1d7a63
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
However every time I install a custom ROM I get stuck in boot loop and the only way to fix it is to go back to stock ROM
Any ideas??
petrjanda said:
OK here is the situation - I have Sense 6/Lolipop 5.0.1 stock ROM( installed via OTA update) on the phone which works.
However every time I install a custom ROM I get stuck in boot loop and the only way to fix it is to go back to stock ROM
Any ideas??
Click to expand...
Click to collapse
You need to manually flash the boot.img file in the custom ROM via ADB while in Fastboot mode, unless you have S-Off. Oh the quirks of HTC phones...
Capt'n Mal said:
You need to manually flash the boot.img file in the custom ROM via ADB while in Fastboot mode, unless you have S-Off. Oh the quirks of HTC phones...
Click to expand...
Click to collapse
Wrong info. Even on s-on M8 phones the boot.img is flashed automatically so that's not it.
@ O.P
Sure you full wiped before installing the new rom. Can you give an example of what roms you tried ?
And DELETE your imei and serial !
Capt'n Mal said:
You need to manually flash the boot.img file in the custom ROM via ADB while in Fastboot mode, unless you have S-Off. Oh the quirks of HTC phones...
Click to expand...
Click to collapse
I dont get it. This wasnt happening before the upgrade to lolipop. It also happens with multirom. Maybe its time to S-off.
Mr Hofs said:
Wrong info. Even on s-on M8 phones the boot.img is flashed automatically so that's not it.
@ O.P
Sure you full wiped before installing the new rom. Can you give an example of what roms you tried ?
And DELETE your imei and serial !
Click to expand...
Click to collapse
Tried ViperOne, Android Revolution HD, SkyDragon.
Yes every installation, I selected I want to wipe.
petrjanda said:
Tried ViperOne, Android Revolution HD, SkyDragon.
Yes every installation, I selected I want to wipe.
Click to expand...
Click to collapse
Hmmm, well i can suggest to make a full wipe manually in TWRP and don't select that in the rom's aroma installer. Then continue to install the full basic rom. Don't delete or modify apps in the installer.
Just flash the correct Lollipop firmware and you're good to go.
Cheers
shirreer said:
Just flash the correct Lollipop firmware and you're good to go.
Click to expand...
Click to collapse
OP is already on LP firmware, based on hboot and radio numbers.
---------- Post added at 09:07 AM ---------- Previous post was at 09:06 AM ----------
Capt'n Mal said:
You need to manually flash the boot.img file in the custom ROM via ADB while in Fastboot mode, unless you have S-Off. Oh the quirks of HTC phones...
Click to expand...
Click to collapse
This only applies to older HTC devices, and has never been true for the M8 (as another already stated). I don't understand why folks keep propagating this incorrect info.
---------- Post added at 09:08 AM ---------- Previous post was at 09:07 AM ----------
petrjanda said:
I have got root and got latest SuperSU and TWRP installed.
Click to expand...
Click to collapse
What version number of TWRP exactly? I ask, since once in a while, folks say they are on the "latest" but then it turns out they are looking in the wrong place, and its actually an older version (and the cause of their issue).
What ROMs specifically did you try?
I did a full wipe(system,data etc except sdcard) in TWRP 2.8.7, and then the install of ViperOne went good.

need stock RUU for htc desire 816 dual sim india

hi all, my phone is stuck on boot mode for a couple of weeks and I am still not able to find correct stock rom. please help me find one so that I can flash it via fastboot. here are the getvar all details from fastboot:
version: 0.5
version-bootloader: 3.19.0.0000
version-baseband: 1.31.50.1103
version-cpld: None
version-microp: None
version-main: 1.61.720.1
version-misc: PVT SHIP S-ON
serialno: FA484MZ00452
product: a5_dwg
platform: hTCBmsm8226
modelid: 0P9C51000
cidnum: HTC__038
battery-status: good
battery-voltage: 0mV
partition-layout: Generic
security: on
build-mode: SHIP
boot-mode: FASTBOOT
commitno-bootloader: be7179e5
hbootpreupdate: 11
gencheckpt: 0
HTC desire 816 A5_dwg
Kit Kat RUU:
http://www.mediafire.com/?jimitej7orp4qcr
Lollipop RUU:
http://www.4shared.com/zip/9nQZohiEba/0P9CIMG_A5_DWG_L50_DESIRE_SENS.html
***RELOCKED***
A5_DWG PVT SHIP S-ON
HBOOT-3.19.0.0000
RADIO-1.31.50.1103
OpenDSP-v28.2.2.00546.0331
OS-1.61.720.1
eMMC-boot 1536MB
Nov 4 2014,20:04:44.23583
I already tried the kitkat one u r posting. it said something remote:12 signature failed
Download lollipop RUU, should work with your device.
Have you tried flashing with sd-card?
When did this bootloop first appear?
nukaru said:
Download lollipop RUU, should work with your device.
Have you tried flashing with sd-card?
When did this bootloop first appear?
Click to expand...
Click to collapse
sorry for late response, I tried the lollipop RUU too
1. with fastboot, it says :02 remote fie is too large
2. via sd card...finding package..opening package....unable to map file
And here is the story of bootloop. my phone was working fine till I received the official lollipop update, which failed repeatedly during installation. I checked the recovery log and found some error in system/bin/flash_camera and decided to flash just recovery image. I flashed recovery and boot image from the ota update I received...but got stuck. then I started trying all these RUU stuff but still no clue. thanks for listening
Ah, okay.
Can you select recovery in hboot and does it start up normally? Have you tried a Kit Kat nandroid backup with twrp?
Ps: you need to delete your imeis in the first post..
nukaru said:
Ah, okay.
Can you select recovery in hboot and does it start up normally? Have you tried a Kit Kat nandroid backup with twrp?
Ps: you need to delete your imeis in the first post..
Click to expand...
Click to collapse
yes once stuck on white screen with htc, I need to hold vol up+ power to turn it off and before it reboots automatically I open hboot by vol down+ power. from there I can continue in recovery mode and fastboot etc. no I haven't tried nandroid backup with twrp. I want to get stock rom so that I am able to get updates in future. plus I read twrp backup roms are havng problems like wifi and all.
That sounds like your bootsector is damaged, so usb debugging is disabled.
Did you back up your old recovery.img? The kit kat one before the update?
The easiest way, if you're able to flash a custom recovery, is a clean nandroid backup without root using twrp and once your device is booting again, start from scratch.
Enable usb debugging, unlock bootloader, flash stock recovery, relock bootloader and flash RUU.
nukaru said:
That sounds like your bootsector is damaged, so usb debugging is disabled.
Did you back up your old recovery.img? The kit kat one before the update?
The easiest way, if you're able to flash a custom recovery, is a clean nandroid backup without root using twrp and once your device is booting again, start from scratch.
Enable usb debugging, unlock bootloader, flash stock recovery, relock bootloader and flash RUU.
Click to expand...
Click to collapse
no I havent backed up the KitKat factory image
I flashed the latest twrp recovery and booted to it. also I placed a twrp stock backup in sd card ( from one of the threads on this forum) . but when I proceed to backup from sd card, it doesn't appear there, however in the install option I can see the contents I placed..but again I m not getting an option to install it from there. guide me what to do next.
shubhamjswl said:
no I havent backed up the KitKat factory image
I flashed the latest twrp recovery and booted to it. also I placed a twrp stock backup in sd card ( from one of the threads on this forum) . but when I proceed to backup from sd card, it doesn't appear there, however in the install option I can see the contents I placed..but again I m not getting an option to install it from there. guide me what to do next.
Click to expand...
Click to collapse
guess wat!! my phone started and I am now getting ota also. thanks
That's great ? Remember to make your own backup and store it somewhere safe ?
Please provide me detailed steps on how to reinstall official stock rom on htc desire 816 dual sim indian version and also rom file
hi all, my phone is stuck on boot mode for weeks and i can't find a usable stock rom for my phone here are the details from fastboot
version: 0.5
version-bootloader: 3.19.0.0000
version-baseband: 1.31.50.1215
version-cpld: None
version-microp: None
version-main:1.27.710.1
version-misc: PVT SHIP S-ON
serialno: FA47RMZ00345
imei: 352795062179097
imei2: 352795062179105
meid: A1000037D93FA6
product: a5_dwg
platform: hTCBmsm8226
modelid: 0P9C51000
cidnum: HTC__621
battery-status: good
battery-voltage: 0mV
partition-layout: Generic
security: on
build-mode: SHIP
boot-mode: FASTBOOT
commitno-bootloader: fba3c246
hbootpreupdate: 11
gencheckpt: 0

Categories

Resources