I have the T999 SG3 model, am rooted and currently running the Wicked v10 rom. I want to try out the 4.3 upgrade and was wondering what the best/safest way is to do this. I already did a nan backup. Do I need to unroot? Thanks in advance for any help/suggestions.
Citadel69 said:
I have the T999 SG3 model, am rooted and currently running the Wicked v10 rom. I want to try out the 4.3 upgrade and was wondering what the best/safest way is to do this. I already did a nan backup. Do I need to unroot? Thanks in advance for any help/suggestions.
Click to expand...
Click to collapse
If you are looking to have your phone download the OTA, then you'd probably need to wipe and install a stock rom. You would then lose root, however. Not sure what the implications of that would be, but I'm sure you'd have to use ODIN, etc, etc, to get back to rooted and custom rom.
I would just flash the stock ROM from DocHoliday's thread instead of going through Odin.. Don't have to worry about Knox or anything, and if you don't like it you can easily wipe and restore your nandroid
Sent from my SGH-T999 using Tapatalk
Related
Hey everyone.
Wondering if anyone can shed some light..
I am currently rooted and using CWM for my recovery and AOKP for my ROM...
i found a thread here that has all the STOCK roms and kernals for Samsung S3.
My question is simple really..
When i flash back to the STOCK ROM and STOCK KERNAL.. would i lose my ROOT? and would i also lose Clockwork recovery?
Thanks
Diamond22 said:
Hey everyone.
Wondering if anyone can shed some light..
I am currently rooted and using CWM for my recovery and AOKP for my ROM...
i found a thread here that has all the STOCK roms and kernals for Samsung S3.
My question is simple really..
When i flash back to the STOCK ROM and STOCK KERNAL.. would i lose my ROOT? and would i also lose Clockwork recovery?
Thanks
Click to expand...
Click to collapse
If you just use mskip's toolkit from the dev section, you can flash back to a stock rom and if you want/need to, you can also flash root and recovery from his tool as well after flashing back to stock.
evodon84 said:
If you just use mskip's toolkit from the dev section, you can flash back to a stock rom and if you want/need to, you can also flash root and recovery from his tool as well after flashing back to stock.
Click to expand...
Click to collapse
Long answer for "Yes" and "Yes"
Sent from my SAMSUNG-SGH-I747 using xda premium
Any link to the thread with the stock ROMs? I am no good at searching for this stuff.
I'll post the link when I am at home for the stock ROMs..
These replies kinda confused me lol...
I don't want to use a toolkit..
I just want to flash the .zip ROM and kernel via CWM..if I do that do I loose my root and CWM?
Or do I need this mskip toolkit to accomplish this? Meaning get rid of root and CWM..
Thanks..sorry..just confuses by the responses..
I'll post the link when I am at home for the stock ROMs..
These replies kinda confused me lol...
I don't want to use a toolkit..
I just want to flash the .zip ROM and kernel via CWM..if I do that do I loose my root and CWM?
Or do I need this mskip toolkit to accomplish this? Meaning get rid of root and CWM..
Thanks..sorry..just confuses by the responses..
Hello all,
I'm using 4.0.4 on I747M with telus. Had to delete the 2 files to disable the OTA update notifications since at the time there was no root for 4.1.2
Now the question is, i've done 1 click with unified toolkit by mskip to root, flash etc.
Can i simply flash any 4.1.2 custom rom or manufacture rom or should i restore to factory default, do the update and then root and do custom rom?
Or naturally is there a simply way to get OTA updates enabled?
Thanks for you help!
to clarify, you are rooted and running the 4.0.4 stock firmware?
if you want to receive OTA updates from your carrier, you need to be on the stock/unrooted firmware.
if you want to run a custom rom, and you're already rooted, install a custom recovery like clockworkmod or twrp. this will allow you to flash a rom. be sure to only flash roms that are intended for your model.
Yeah i already have CW. just wanted to make sure if going different build will cause issues.
Thanks!
xBeerdroiDx said:
to clarify, you are rooted and running the 4.0.4 stock firmware?
if you want to receive OTA updates from your carrier, you need to be on the stock/unrooted firmware.
if you want to run a custom rom, and you're already rooted, install a custom recovery like clockworkmod or twrp. this will allow you to flash a rom. be sure to only flash roms that are intended for your model.
Click to expand...
Click to collapse
silentq said:
Yeah i already have CW. just wanted to make sure if going different build will cause issues.
Thanks!
Click to expand...
Click to collapse
if you have an i747 or i747M, stick with those ROMs as anything else will cause serious problems with your device.
xBeerdroiDx said:
if you have an i747 or i747M, stick with those ROMs as anything else will cause serious problems with your device.
Click to expand...
Click to collapse
i was gonna go with MIUI http://forum.xda-developers.com/showthread.php?t=1857399
silentq said:
i was gonna go with MIUI http://forum.xda-developers.com/showthread.php?t=1857399
Click to expand...
Click to collapse
if you're on an i747/i747M than that should be just fine. remember to make a backup first and perform a full wipe before flashing. if you're unfamiliar with some of these techniques, follow the link in my signature. it outlines what procedures to follow to safely get you running smooth.
I am trying to find the easiest way possible for someone to flash the updated md4 stock rom. This person is already rooted. They want to upgrade so they will have multiwindow. They are in another city so I cant do it myself. I remember Treve has a rom that backs up your rom before it flashes the unrooted stock. I was wondering is there something similar to that but will flash the rooted latest stock?
Here is the thread with the md4 modem/baseband. I've never seen a ROM that makes a back up for you. You can make nandroid while in recovery. That will be the back up you need in the event of a problem.
http://forum.xda-developers.com/showthread.php?p=32152586
sent from GS3 gone Wicked
mystery_tx_man said:
I am trying to find the easiest way possible for someone to flash the updated md4 stock rom. This person is already rooted. They want to upgrade so they will have multiwindow. They are in another city so I cant do it myself. I remember Treve has a rom that backs up your rom before it flashes the unrooted stock. I was wondering is there something similar to that but will flash the rooted latest stock?
Click to expand...
Click to collapse
Using ODIN is the best way to go. This link explains everything. All that person needs to know is how to open the ODIN, select file under PDA option and click Start.
mystery_tx_man said:
I am trying to find the easiest way possible for someone to flash the updated md4 stock rom. This person is already rooted. They want to upgrade so they will have multiwindow. They are in another city so I cant do it myself. I remember Treve has a rom that backs up your rom before it flashes the unrooted stock. I was wondering is there something similar to that but will flash the rooted latest stock?
Click to expand...
Click to collapse
Forget using Odin, your friends s3 is already rooted no need to go through all that useless work.
The easiest way is to flash Freezas prerooted stock md4 rom http://forum.xda-developers.com/showthread.php?p=32176586
Sent from the future via Tapatalk 4
Hello, I am currently rooted and have CWM 6.0.4.3. installed. I'm on CM11 but want to go back to stock.. Is there an easy way to keep root and go back to stock. Want stock for a few functions that ROMS dont seem to be offering but can keep root and CWM ??
Thanks.
Which phone do you have? You could try flashing a pre-rooted stock ROM via Odin. Then use Odin to flash CWM.
Bt its better to firstly install ur stock rom and then again root it as it takes no longer than 5 mins
DeathNotice said:
Bt its better to firstly install ur stock rom and then again root it as it takes no longer than 5 mins
Click to expand...
Click to collapse
Ok perfect, thats what I was looking for. Phone btw is S3 - d2att - SGH i747) Sounds good to install the stock rom and re-root.. I'm sure its here but I have searched everywhere to find a tutorial on this and I cannot find a straight answer.
Would you mind giving me the steps or pointing me to a thread that explains how to and has the files in need to download ?
audit13 said:
Which phone do you have? You could try flashing a pre-rooted stock ROM via Odin. Then use Odin to flash CWM.
Click to expand...
Click to collapse
Do you know if there is a step by step on this somewhere ? I dont mind going back to complete stock.. I can just re-root and flash CWM after.
OR
Maybe you could just answer the bigger question : the reason I want to go back to stock is I need to use MHL/HDMI which CM11 doesnt support. I dont want to go back to stock, I would rather even go to another ROM that supports mhl/hdmi.. but if I have to go to stock, than so be it.?
Were you running the stock AT&T 4.3 ROM before you switched to CM11?
audit13 said:
Were you running the stock AT&T 4.3 ROM before you switched to CM11?
Click to expand...
Click to collapse
Yes, I bought the phone new and was running stock, Canadian Rogers version and had changed to CM10, then to 11.
robberrobbie said:
Yes, I bought the phone new and was running stock, Canadian Rogers version and had changed to CM10, then to 11.
Click to expand...
Click to collapse
Since you installed a custom recovery, that would have tripped the Knox counter which voids the warranty. It's not a problem if the phone is working properly.
Did you update to 4.3 or did it come with 4.3?
You may be better off installing a pre-rooted ROM.
http://forum.xda-developers.com/showthread.php?t=1739426
audit13 said:
Since you installed a custom recovery, that would have tripped the Knox counter which voids the warranty. It's not a problem if the phone is working properly.
Did you update to 4.3 or did it come with 4.3?
You may be better off installing a pre-rooted ROM.
http://forum.xda-developers.com/showthread.php?t=1739426
Click to expand...
Click to collapse
It was quite some time ago but I believe I was on ICS 4.0.. and switch to CM from there. Im not worried about the counter for warranty, that's expired on my unit anyways. I just want to be able to use MHL/HDMI function.. so if fine with flashing pre-rooted.. or stock.. or a different ROM that support MHL/HDMI. Can you recommend the easiest route ?
robberrobbie said:
It was quite some time ago but I believe I was on ICS 4.0.. and switch to CM from there. Im not worried about the counter for warranty, that's expired on my unit anyways. I just want to be able to use MHL/HDMI function.. so if fine with flashing pre-rooted.. or stock.. or a different ROM that support MHL/HDMI. Can you recommend the easiest route ?
Click to expand...
Click to collapse
I asked about 4.3 because the 4.3 bootloader cannot be downloaded. Flashing via mobile Odin will not touch the bootloader or modem.
You could try a pre-rooted rom and then flash a custom recovery via Odin.
I use Philz Touch from here: http://goo.im/devs/philz_touch/CWM_Advanced_Edition/d2att
audit13 said:
I asked about 4.3 because the 4.3 bootloader cannot be downloaded. Flashing via mobile Odin will not touch the bootloader or modem.
You could try a pre-rooted rom and then flash a custom recovery via Odin.
I use Philz Touch from here: http://goo.im/devs/philz_touch/CWM_Advanced_Edition/d2att
Click to expand...
Click to collapse
Ok thanks, I will do that. 1 thing I'm not quite sure of is the bootloader situation ? In the first tutorial there is a note : Flashing a prior bootloader can hard/soft brick your device. How do I know ?
I see the steps as:
Extract tar file you downloaded.
Use Odin, put phone into download mode [with phone off, hold vol. down + home + power ], connect to computer and open Odin.
once in odin click the PDA field and select the tar file
Leave Auto Reboot and F. Reset Time checked.
click start and when done let phone reboot.
If you just want a stock, rooted phone with no custom recovery, no plans to flash custom roms, etc. then you can stop HERE.
For my situation, is it just that easy ?
Before flashing, verify the version of your bootloader.
audit13 said:
Before flashing, verify the version of your bootloader.
Click to expand...
Click to collapse
OK I have made an effort to go read and figure out how to find out what version of bootloader on my own.. But i cannot find ? Any chance you know... And could help?
You mentioned your have the i747 and Rogers. Do you have the AT&T s3 (i747) or Rogers/Bell/Telus s3 (i747m)?
What is the most recent stock ROM you had on your phone?
Hey. I got the i747m. As for what was the last stock ROM I had, can't say. I know when I bought the phone it was ICS and I had received and update to jellybean.. But them went to cm10. The tutorial I followed told me had me back everything up, which I did. Have it in a file somewhere on my comp, would that tell me ?
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
If you are flasjing back to stock you should flash back to the same baseband/bootloader that came stock on your phone.
I'm looking for a stock rooted zip for the sasktel i747m (MF1) that i can flash in CWM....I need to go back to stock to fix a data issue that ive encountered through flashing these new d2lte builds...
Does anyone know if a cwm flashable stock rooted rom exists for Sasktel's i747m with baseband MF1 ???I already have the Odin flashable stock rooted zip but don't have a laptop handy until tuesday....And im pretty sure i cant flash that zip in cwm recovery....
Sent from my SAMSUNG-SGH-I747 using XDA Premium 4 mobile app
Ariesdroid said:
If you are flasjing back to stock you should flash back to the same baseband/bootloader that came stock on your phone.
I'm looking for a stock rooted zip for the sasktel i747m (MF1) that i can flash in CWM....I need to go back to stock to fix a data issue that ive encountered through flashing these new d2lte builds...
Does anyone know if a cwm flashable stock rooted rom exists for Sasktel's i747m with baseband MF1 ???I already have the Odin flashable stock rooted zip but don't have a laptop handy until tuesday....And im pretty sure i cant flash that zip in cwm recovery....
Sent from my SAMSUNG-SGH-I747 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I have not seen a stock mf1 ROM that can be flashed in CWM. You could use mobile Odin to flash back to stock and then flash Philz Touch via desktop Odin later.
OK, so back to my question.. If I have the i747M and bought the phone with ICS.. does this help.?
audit13 said:
You mentioned your have the i747 and Rogers. Do you have the AT&T s3 (i747) or Rogers/Bell/Telus s3 (i747m)?
What is the most recent stock ROM you had on your phone?
Click to expand...
Click to collapse
Hey there Audit, Sorry to bother you again, I just dont know how to move forward from here and neeeeeed some help.
I have been reading for days and days have not found a straight answer for my issue and I dont want to just go ahead and start flashing when I dont know if its the right method ?
I dont know how to get back to stock from where I'm at, I dont know how to figure out what bootloader I have (you asked me)
I have found a couple links on XDA that I can follow, I'm just not sure if they apply to my situation ?
This is a pretty detailed response/tutorial, but I dont know if I can just go ahead with this or not ?
http://forum.xda-developers.com/showthread.php?t=2186967
This is also very detailed: http://forum.xda-developers.com/showthread.php?t=1739426
Any help would be greatly appreciated !
robberrobbie said:
OK, so back to my question.. If I have the i747M and bought the phone with ICS.. does this help.?
Click to expand...
Click to collapse
If you are sure you have the Rogers i747m and you have never loaded a stock Rogers 4.3 ROM onto your phone, you could use desktop Odin to flash a pre-rooted 4.1.2 ROM from here: http://forum.xda-developers.com/showthread.php?t=1739426.
Flashing the pre-rooted 4.1.2 ROM will return the phone to completely stock, wipe out all installed apps and data, and you will have root. I do not recommend flashing the Rogers 4.3 pre-rooted ROM from the link.
Once you are able to boot into the phone and set things up, you can flash Philz Touch from Odin which will give you a custom recovery on a rooted stock 4.1.2 ROM.
I attempted to flash a 4.4.2 rom yesterday but it couldnt and it gave me a status 7 error. I looked it up and people said that you have to update clockworkmod. Well i tried to through terminal but it couldn't. It said something like could not find directory. So if anyone has any idea what I can do pleast tell me.
Using Galaxy s3 sgh-i747 on PA 3.99.1 ROM
Flash Philz Touch from here via Odin (use the tar version in PDA): http://goo.im/devs/philz_touch/CWM_Advanced_Edition/d2att
alright i did it through odin and it worked..now im gonna make a backup again and try flashing a rom. hope it works. thanks for the help
If you can't flash a KK ROM, you may need to update your bootloader. If you're not on a 4.3 bootloader, try and avoid it for now.
audit13 said:
If you can't flash a KK ROM, you may need to update your bootloader. If you're not on a 4.3 bootloader, try and avoid it for now.
Click to expand...
Click to collapse
im on a 4.3 rom but if i get error status 7 again ill just restore my backup and avoid it...is there a 4.3 bootloader? Also i was about to wipe it but its asking me wipe data/factory reset or clean to install a new ROM. I suggest its the 2nd one but if i do it and it doesnt work can i still restore my backup?
orlans21 said:
im on a 4.3 rom but if i get error status 7 again ill just restore my backup and avoid it...is there a 4.3 bootloader? Also i was about to wipe it but its asking me wipe data/factory reset or clean to install a new ROM. I suggest its the 2nd one but if i do it and it doesnt work can i still restore my backup?
Click to expand...
Click to collapse
There is a 4.3 bootloader that would be installed if you ran an OTA update to 4.3 or you manually installed the 4.3 bootloader.
Did you make your backup using Philz? If not, make the backup using Philz, then wipe and install.
audit13 said:
There is a 4.3 bootloader that would be installed if you ran an OTA update to 4.3 or you manually installed the 4.3 bootloader.
Did you make your backup using Philz? If not, make the backup using Philz, then wipe and install.
Click to expand...
Click to collapse
I just made a backup on Philz and im not sure if i installed a 4.3 bootloader manually or OTA. Just to be clear im wiping to install ROM. so the 2nd option
orlans21 said:
I just made a backup on Philz and im not sure if i installed a 4.3 bootloader manually or OTA
Click to expand...
Click to collapse
Doesn't really matter but it's good to know that you need to stay away from any attempts to downgrade the bootloader.
hahah why would i want to downgrade?
orlans21 said:
hahah why would i want to downgrade?
Click to expand...
Click to collapse
I have seen posts where people bricked their phone when trying to return to a stock ROM using Odin.
well...im gonna have to put it back to a stock rom when i get a new phone and give this to my dad...i still have the 4.1 stock downloaded on my computer...i dont even remember how to put it back now lol. so i should try flashing a 4.4.2 rom? which rom do you prefer? i have carbon and liquidsmooth. i want halo like i do on PA and both have it i believe
orlans21 said:
well...im gonna have to put it back to a stock rom when i get a new phone and give this to my dad...i still have the 4.1 stock downloaded on my computer...i dont even remember how to put it back now lol
Click to expand...
Click to collapse
You can't restore to a completely stock ROM not that you have a 4.3 bootloader. AT&T never released a full 4.3 stock ROM, only an update to 4.3 from an earlier stock ROM.
If you did not have a 4.3 bootloader, you could install any stock AT&T ROM such as 4.1.1. Being able to restore to stock 4.1.1 would also allow you to sim unlock your phone for free, if necessary.
audit13 said:
You can't restore to a completely stock ROM not that you have a 4.3 bootloader. AT&T never released a full 4.3 stock ROM, only an update to 4.3 from an earlier stock ROM.
Click to expand...
Click to collapse
well im on rogers and its the same as att. i still have the original samsung touchwiz 4.1 rom just incase anything happens.
Your original post said you have an sgh-i747 which is an AT&T model. If you have a Rogers s3, it's an sgh-i747m.
Regardless of which model you have, you can't downgrade from any 4.3 bootloader which means you can't completely revert back to 4.1.1. The best you could do would be to run 4.1.1 on a 4.3 bootloader.
audit13 said:
Your original post said you have an sgh-i747 which is an AT&T model. If you have a Rogers s3, it's an sgh-i747m.
Regardless of which model you have, you can't downgrade from any 4.3 bootloader which means you can't completely revert back to 4.1.1. The best you could do would be to run 4.1.1 on a 4.3 bootloader.
Click to expand...
Click to collapse
sorry i should have included the m lol. i wont worry about going back to 4.1 until the galaxy s5 comes out and im ready to give it to my dad. but back to focusing on this. im about to attempt to flash a 4.4.2 rom. either liquidsmooth or carbon. what do you like?
I prefer Validus version 4.3 because it includes Nova Launcher and it has a dark UI theme.
but thats 4.3. i wanna be on 4.4 and im installing nova and making it the way i had it before.
wait a second is it a 4.4 rom?
orlans21 said:
but thats 4.3. i wanna be on 4.4 and im installing nova and making it the way i had it before.
wait a second is it a 4.4 rom?
Click to expand...
Click to collapse
It is a 4.4.2-based rom. The release is version 4.3.
hmm interesting...you do recommend it? what great features does it come with?
I like it because it's a very stripped-down ROM, has a dark UI, and is AOSP-based.
It's not radically different from other ROMs but has exactly what I want. I run the same ROM on a Nexus 4 and Motorola Atrix HD.