I tried to upgrade my rom but the process crashed. The utility mtty doesn't work because when I connect the universal, boatloader mode by the cable, to the pc, it says "USB not recognized" (sometimes when I connect the computer is frozen till I disconnect the cable of the universal)
Please, I tried to have some solutions in the forum but all the posts indicates is needed previously the usb connection.
Do you know if should be possible to run the flash of the rom in other way, for example using a serial cable connected into the miniusb of the universal, because the boatloader screen says "Serie, v.1.01"
I apprecite what you can say please, I'm really in a hole.
Try this...
Try taking out the battery for a few minutes (10-30mins) and reboot your PC then repeat upgrade process. Hope that helps. Good luck!!!
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
The only thing I found that worked was to try a different PC, then it was fine...
sl9 said:
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
The only thing I found that worked was to try a different PC, then it was fine...
Click to expand...
Click to collapse
In my case it still happening in other computers. Conclussion: some piece of the software in the universal has been lost. The screen shows "Serial" that means on some way that is opened to comunication but not USB.
My questions are:
- should be possible to put some starting software in SD and do the universal boot on it.
- do you know how to connect to the computer COM! port from the usb miniport of the Universal.
I appreciate, I was not planning to replace now the Universal...
beginner said:
sl9 said:
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
Now works.... I still thinking windows is so stupid software made for distroy our mind ....
Solved after install drivers for a converter usb -rs232 ( I was looking for the way to connect from rs232 the universal)
I'm happy again and I promise don't try to change rom again (at least for a while)
If some person is interested in what brand of software/hardware I installed, send me a mail...
Thanks hearing me ...
Click to expand...
Click to collapse
Click to expand...
Click to collapse
i have the same problem with my friend's uni
does it mean that you don't have to own any adapter, just have to install drivers for USB to RS232 adapter
if yes, where to find it?
thanx
respectfully
ZeD
zedino said:
i have the same problem with my friend's uni
does it mean that you don't have to own any adapter, just have to install drivers for USB to RS232 adapter
if yes, where to find it?
thanx
respectfully
ZeD
Click to expand...
Click to collapse
I want to say that is running after doing some things and obviously some of it solved my problems. I made:
- unistall last version of activesync and go back to version 4.0
- delete all the applications using ports usb.
due the connection still not running (windows message: device not recognized) and because in the screen of universal I saw: "COMM1" I tried to connect from computer port rs232. By that I purchased some special cable, name: hama brand, rs232 serial, 9 pin - usb.
As you can imagine all the steps I followed were followed by the typical restart of windows. In this sense is important to say that the universal, after connect, need to do a soft reset each time (again windows....)
Other comment is that I unmark the option to connect by usb in activesync and mark the connection by com1.
and after all was done, connecting by usb the unniversal, kill wcescomm, windows said "NEw usb device, sync device". I started mtty and now appears the USB option, great! same time the screen in universal changed from comm1 to usb, more great....
and that's all.
does it mean you solve your problem using special USB 2 RS232 connector?
ZeD
PS: it was my first idea , but i still believe i can solve the problem using USB port
zedino said:
does it mean you solve your problem using special USB 2 RS232 connector?
ZeD
PS: it was my first idea , but i still believe i can solve the problem using USB port
Click to expand...
Click to collapse
I think my english wording was not fine. I mean I solved my problem after install the sofware -drivers- of the rs232 connector, but connecting to the universal by usb as on standard way I was syncronizing previous the crack with activesync.
OK, where to get this driver?
thanx
?????????? NOTHING ?????????????
zedino said:
OK, where to get this driver?
thanx
Click to expand...
Click to collapse
Try here.
http://www.hama.de/portal/type*3/action*1026/searchMode*1/q*039703
I have had the same problem several times now (search the forum for the thread).
I tried three different PC's/laptops and three different USB cables all with the same error as yourself.
Eventually I got a connection but the laborious process of trying - failing, restarting windows and soft resetting the phone, trying - failing........... until it finally worked. I did nothing differently the time that it worked but the strange thing is that it has worked every time since! Maybe the USB driver the phone has a bug in it that causes it to get 'stuck' in a mode where it will no longer correctly operate but once you have managed to 'kick' it into action it seems toi then carry on working.
It was also a ROM upgrade that caused my USB phone driver to stop functioning. Maybe the fact that the phone has a slightly diffferent software configuration after the upgrade but exactly the same hardware fingerprint causes the driver to fail.
Every time that I have had this problem it is after an upgrade but once I have gotten it to work once with the new ROM, it always continues to function - until the next upgrade.
shrubbery said:
I have had the same problem several times now (search the forum for the thread).
I tried three different PC's/laptops and three different USB cables all with the same error as yourself.
Eventually I got a connection but the laborious process of trying - failing, restarting windows and soft resetting the phone, trying - failing........... until it finally worked. I did nothing differently the time that it worked but the strange thing is that it has worked every time since! Maybe the USB driver the phone has a bug in it that causes it to get 'stuck' in a mode where it will no longer correctly operate but once you have managed to 'kick' it into action it seems toi then carry on working.
It was also a ROM upgrade that caused my USB phone driver to stop functioning. Maybe the fact that the phone has a slightly diffferent software configuration after the upgrade but exactly the same hardware fingerprint causes the driver to fail.
Every time that I have had this problem it is after an upgrade but once I have gotten it to work once with the new ROM, it always continues to function - until the next upgrade.
Click to expand...
Click to collapse
not works, probably is this device lost forever, i have restarted device and PC almost hundred times, still the same result, uni stuck in Bootloader screen top of page "Serial" bottom of page "v1.00"
nothing changed, even if i connect to USB port
if someone have some solution to this s*it pls let me know
thanx
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
mrijnvis said:
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
Click to expand...
Click to collapse
no, my problem persist, hundred times i tried to recover friends device using upgrade by original shipped ROM but the device is not recognized by system so there is allways connection error, so this kind of reliving this UNI is not usable
anyway, thanx for raply and suggestion
ZeD
mrijnvis said:
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
Click to expand...
Click to collapse
If you're stuck in bootloader mode only, visit www.buzzdev.netand look for ExitBootloader utility written by the great Buzz. Just follow his instructions or scroll thru' Universal's forum here and there for problems relating to "stuck in bootloader"
hope this helps
no device is not recognized by PC so any trying to use exitbl is not available, anyway this option was one of the first what i have tried
thanx anyway
ZeD
i had the same problem with the QTEK of my principal after I upgraded his ROMs.
(after the hard reset, the pocket remained in bootloader mode).
you can solve this problem in a very simple way:
you have to launch the bootloader installation (BL1.01_RUU_UNI_V.1.2.EXE) from the PC (still connected with the PPC through USB) while the PPC is in bootloader mode (on your display you see "USB > Serial 1.01" or something like that).
then you do a SOFT reset and the pocket boot normally.
very simple.
i hope to be helpful to someone.
zedino said:
no device is not recognized by PC so any trying to use exitbl is not available, anyway this option was one of the first what i have tried
thanx anyway
ZeD
Click to expand...
Click to collapse
I had some problem. After uninstall all usb applications in the pc and install the software for cable usb -rs 232, doing some softreset in the pda connected, it turned the screen message "Com" by "Usb"
I was trying to put the hum/hiss sound fix on my sd card and I cannot get my pc to connect via USB...
My wife has a TP2 and it connects fine...
I have tried with/without the sd card in, rebooted the pc and phone, rebooted the phone while connected to the pc.... nothing...
wtf...
anyone else with this problem?
PS... NRGZ28 had posted a very basic rom for booting to android back in Feb and it is now gone from hotfile. Anyone know of a quick boot into android?
- Try a different computer
- Try a hard reset
That are the first thing you should do.
Tried hard reset...
Dif PC is not an option at the moment... I have rebooted...
Just flashed the ROM (NRGZ newest, thank goodness I had it on my SD card) and I still cant get it to sync...
I have attached the USB error I am getting... (Win7, new install)
The phone is not asking if I want to active sync or use as storage???? wtf...
FarBeyond said:
Just flashed the ROM (NRGZ newest, thank goodness I had it on my SD card) and I still cant get it to sync...
I have attached the USB error I am getting... (Win7, new install)
The phone is not asking if I want to active sync or use as storage???? wtf...
Click to expand...
Click to collapse
Reboot your PC? lol bet your tried that already...
Try this:
settings > connections > usb to pc > and disable Faster Data Sync then try. This way uses the generic usb drivers and maybe it will connect.
That did not work...
How do I get my Win7 laptop to see the phone with Android on it?
FarBeyond said:
That did not work...
How do I get my Win7 laptop to see the phone with Android on it?
Click to expand...
Click to collapse
dont think thats working yet
Ya I don't think that works yet, it's tied to Android software drivers and the use of the USB port, since there is no drivers to control the port only to charge battery. Windows thinks there is something there, but the phones USB can't communicate back....I think this is the issue or at lease after playing around with it on my phone anyway
Not that it's a huge amount of help but might troubleshoot down to the hardware level...if you go into bootloader mode on the phone and connect to USB does it connect?
I don't think you should go that deep and dirty. My touch pro 2 works only with only 1 (non-HTC) cable of the 10 i have at home, all are the "standard" mini-USB but only one works flawlessly for communicating/flashing/syncing, the other cables either do the same error - device not recognized - or windows says that the device could communicate faster - and only copies files slowly.
All in all: you should simply check with another USB cable or if you have the factory HTC cable try it with that. I noticed that the cable i am using other than the HTC one is a very good quality thick (low-resistance and double-shielded) USB cable and it never failed on me.
One other thing you should definitely watch for: plug the USB cable into the motherboard USB port directly (on the back of the PC where you plug the keyboard, mouse etc.), sometimes PC cases with front panel USB outputs simply die, or are wrongly attached to the motherboard USB header and it can cause the aforementioned problems too, not to mention if it is wrongly attached it could harm your phone too.
please help me i m in a big problem the problem is something like this http://forum.xda-developers.com/showthread.php?t=641444
guys i need help in very serious problem first of all sorry for ma bad english
the problem is that i can,t connect my rhodium210 to pc my can,t detect it my pc has all drivers installed because it detects my sister phone very easily my sister also has rhodium210 actually when i try to connect it with my pc it only charges nothing happens in phone it can,t ask me for which usb mode you want so thats why my pc can,t
detect it but it detects my sister's phone very easily i also try to flash stock rom from sd card hard reset my phone many times i installed many android on my rhod210 thats why the prob starts i also try to connect my phone in bootloader mode but it shows only serial not usb but the cable is connected i think that it is a hardware issue i think i damaged my rhod210 hardwares by flashing it continously can some one give me a good sol ...........
Moved to General Q&A.
Hi!
My name is MyThejuli and i have a big problem with my note 2(international n7100)!!
Problem:
I want to connect my phone to my pc but it wont work.
What i tried to do:
Changed rom,changed usb flex(original one),changed usb cable(all oem and all from other note 2 users where their usb to pc works,5 of them)
Changed pc(4 times (vista, xp, 7, and my pc win7 and8)
Changed radio,went to the A1 store(yes im Form austria)(they sad i should replace(for 450€) it but i need the phone!)
Changed the drivers on the pc and installed them...+changed the usb flex again... *POKERFACE*
Changed quallcom usb settings back and forth(between mtp and mtp+...)
I dont know what to do now i had a problem with my efs partition (suddenly rebooted then there was no h/w number and no imei and no receiption)<--- Fixed
in the past. but after that (2 weeks later the usb problem began...)
Im currently using the standard 4.3 test firmware
PLS help me im normally very good at computers and phone but i cant get it to work i want my usb back(its charging fast since usb flex change number 2)
Pls its hopeless for me i tried every damn thing to get this to work! But nothing works!!!!!!!
Sorry for y and z error using false keyboard layout and cant switch it(i dont know how.. i changed it in the settings but layout is always the same)
Thanks!
PS: please dont say that i should find a genuine seller because i tried another one from a friends note II and it didnt work!
PPS: I have the flex from TOKKA-VERSAND (good german amazon seller) and the first replacement, also from amazon but i dont know the seller anymore.
PPPs: If nothing works i would sell it!PM me if you are interrested!
Hi,
Have you found a fix on this one? I'm having the same problem. When I plug my note 2 to my PC, it charges but it is not being detected by the PC. I've read posts saying that this problem is caused by the USB fast charge being enabled in the device.
Let me know if you already found a solution to this one.
Thank you.
my note 2 is running normal and I connect it on pc today and he just loaded, but do not want to connect more in no uniformed of 3 pc I have at home, but yesterday he connected normal. even bought a usb flex to see if solved, but not forward, already removed and installed the samsung drivers, kies too, but not forward.
in windows device manager has an error: unknown device (failure device descriptor request)
I'm already crazy here, because not get to spend anything to phone and or copy it to the PC, please help me .... :crying:
you could try other wires, maybe there's something wrong with the wire. =)
I've tried with 5 cables here , both original and of poor quality, and any positive results .
tadshakur said:
I've tried with 5 cables here , both original and of poor quality, and any positive results .
Click to expand...
Click to collapse
Did you try different kernels and Roms?
I use a india stock ROM , because the phone is imported and I 'm from Brazil , and used a modified karnel , and all roms that I tried to put gave failure in Odin.
And now with this problem, not of to try to install a ROM or kernel via Odin, and I'm afraid to try to flash any ROM or kernel and gives problem , then I iron made ..
My smartphone also not recognize any stick by OTG cable, it recognizes that the USB OTG cable is connected, but not nothing happens, does not appear the flash drive in the file explorer, can it be a problem on the main board ???
Please, if anyone has any solution help me !!!!!