I tried to upgrade my rom but the process crashed. The utility mtty doesn't work because when I connect the universal, boatloader mode by the cable, to the pc, it says "USB not recognized" (sometimes when I connect the computer is frozen till I disconnect the cable of the universal)
Please, I tried to have some solutions in the forum but all the posts indicates is needed previously the usb connection.
Do you know if should be possible to run the flash of the rom in other way, for example using a serial cable connected into the miniusb of the universal, because the boatloader screen says "Serie, v.1.01"
I apprecite what you can say please, I'm really in a hole.
Try this...
Try taking out the battery for a few minutes (10-30mins) and reboot your PC then repeat upgrade process. Hope that helps. Good luck!!!
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
The only thing I found that worked was to try a different PC, then it was fine...
sl9 said:
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
The only thing I found that worked was to try a different PC, then it was fine...
Click to expand...
Click to collapse
In my case it still happening in other computers. Conclussion: some piece of the software in the universal has been lost. The screen shows "Serial" that means on some way that is opened to comunication but not USB.
My questions are:
- should be possible to put some starting software in SD and do the universal boot on it.
- do you know how to connect to the computer COM! port from the usb miniport of the Universal.
I appreciate, I was not planning to replace now the Universal...
beginner said:
sl9 said:
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
Now works.... I still thinking windows is so stupid software made for distroy our mind ....
Solved after install drivers for a converter usb -rs232 ( I was looking for the way to connect from rs232 the universal)
I'm happy again and I promise don't try to change rom again (at least for a while)
If some person is interested in what brand of software/hardware I installed, send me a mail...
Thanks hearing me ...
Click to expand...
Click to collapse
Click to expand...
Click to collapse
i have the same problem with my friend's uni
does it mean that you don't have to own any adapter, just have to install drivers for USB to RS232 adapter
if yes, where to find it?
thanx
respectfully
ZeD
zedino said:
i have the same problem with my friend's uni
does it mean that you don't have to own any adapter, just have to install drivers for USB to RS232 adapter
if yes, where to find it?
thanx
respectfully
ZeD
Click to expand...
Click to collapse
I want to say that is running after doing some things and obviously some of it solved my problems. I made:
- unistall last version of activesync and go back to version 4.0
- delete all the applications using ports usb.
due the connection still not running (windows message: device not recognized) and because in the screen of universal I saw: "COMM1" I tried to connect from computer port rs232. By that I purchased some special cable, name: hama brand, rs232 serial, 9 pin - usb.
As you can imagine all the steps I followed were followed by the typical restart of windows. In this sense is important to say that the universal, after connect, need to do a soft reset each time (again windows....)
Other comment is that I unmark the option to connect by usb in activesync and mark the connection by com1.
and after all was done, connecting by usb the unniversal, kill wcescomm, windows said "NEw usb device, sync device". I started mtty and now appears the USB option, great! same time the screen in universal changed from comm1 to usb, more great....
and that's all.
does it mean you solve your problem using special USB 2 RS232 connector?
ZeD
PS: it was my first idea , but i still believe i can solve the problem using USB port
zedino said:
does it mean you solve your problem using special USB 2 RS232 connector?
ZeD
PS: it was my first idea , but i still believe i can solve the problem using USB port
Click to expand...
Click to collapse
I think my english wording was not fine. I mean I solved my problem after install the sofware -drivers- of the rs232 connector, but connecting to the universal by usb as on standard way I was syncronizing previous the crack with activesync.
OK, where to get this driver?
thanx
?????????? NOTHING ?????????????
zedino said:
OK, where to get this driver?
thanx
Click to expand...
Click to collapse
Try here.
http://www.hama.de/portal/type*3/action*1026/searchMode*1/q*039703
I have had the same problem several times now (search the forum for the thread).
I tried three different PC's/laptops and three different USB cables all with the same error as yourself.
Eventually I got a connection but the laborious process of trying - failing, restarting windows and soft resetting the phone, trying - failing........... until it finally worked. I did nothing differently the time that it worked but the strange thing is that it has worked every time since! Maybe the USB driver the phone has a bug in it that causes it to get 'stuck' in a mode where it will no longer correctly operate but once you have managed to 'kick' it into action it seems toi then carry on working.
It was also a ROM upgrade that caused my USB phone driver to stop functioning. Maybe the fact that the phone has a slightly diffferent software configuration after the upgrade but exactly the same hardware fingerprint causes the driver to fail.
Every time that I have had this problem it is after an upgrade but once I have gotten it to work once with the new ROM, it always continues to function - until the next upgrade.
shrubbery said:
I have had the same problem several times now (search the forum for the thread).
I tried three different PC's/laptops and three different USB cables all with the same error as yourself.
Eventually I got a connection but the laborious process of trying - failing, restarting windows and soft resetting the phone, trying - failing........... until it finally worked. I did nothing differently the time that it worked but the strange thing is that it has worked every time since! Maybe the USB driver the phone has a bug in it that causes it to get 'stuck' in a mode where it will no longer correctly operate but once you have managed to 'kick' it into action it seems toi then carry on working.
It was also a ROM upgrade that caused my USB phone driver to stop functioning. Maybe the fact that the phone has a slightly diffferent software configuration after the upgrade but exactly the same hardware fingerprint causes the driver to fail.
Every time that I have had this problem it is after an upgrade but once I have gotten it to work once with the new ROM, it always continues to function - until the next upgrade.
Click to expand...
Click to collapse
not works, probably is this device lost forever, i have restarted device and PC almost hundred times, still the same result, uni stuck in Bootloader screen top of page "Serial" bottom of page "v1.00"
nothing changed, even if i connect to USB port
if someone have some solution to this s*it pls let me know
thanx
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
mrijnvis said:
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
Click to expand...
Click to collapse
no, my problem persist, hundred times i tried to recover friends device using upgrade by original shipped ROM but the device is not recognized by system so there is allways connection error, so this kind of reliving this UNI is not usable
anyway, thanx for raply and suggestion
ZeD
mrijnvis said:
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
Click to expand...
Click to collapse
If you're stuck in bootloader mode only, visit www.buzzdev.netand look for ExitBootloader utility written by the great Buzz. Just follow his instructions or scroll thru' Universal's forum here and there for problems relating to "stuck in bootloader"
hope this helps
no device is not recognized by PC so any trying to use exitbl is not available, anyway this option was one of the first what i have tried
thanx anyway
ZeD
i had the same problem with the QTEK of my principal after I upgraded his ROMs.
(after the hard reset, the pocket remained in bootloader mode).
you can solve this problem in a very simple way:
you have to launch the bootloader installation (BL1.01_RUU_UNI_V.1.2.EXE) from the PC (still connected with the PPC through USB) while the PPC is in bootloader mode (on your display you see "USB > Serial 1.01" or something like that).
then you do a SOFT reset and the pocket boot normally.
very simple.
i hope to be helpful to someone.
zedino said:
no device is not recognized by PC so any trying to use exitbl is not available, anyway this option was one of the first what i have tried
thanx anyway
ZeD
Click to expand...
Click to collapse
I had some problem. After uninstall all usb applications in the pc and install the software for cable usb -rs 232, doing some softreset in the pda connected, it turned the screen message "Com" by "Usb"
Related
I have a problem. My Exec is stuck on the bootloader screen. All I see is Serial at the top, and v1.00 at the bottom.
When I connect my exec via USB, the screen continues to say Serial (rather than switching to USB) and the PC I connect to 'installs' the device as 'unknown device' in device manager.
I've seen mention of the problem elsewhere on the site, but the only solution I can find seems to be to keep trying, and eventually it's recognised. So far, after three days of trying, it has not been recognised.
I am aware of Buzz tool to get the device out of bootloader mode, but that required a connection to be established, which at the moment, I can't do.
Has anyone got any experience of this, or any ideas as to what's causing this, or how this can be fixed? I have tried uninstalling the 'unknown device' from device manger, restarting the PC (and hard reset of the Exec) then reconnecting, but the same thing happens every time.
Any ideas would be appreciated, as I'm currently staring at a rather expensive paper weight.
Try this it shld work
hdubli said:
This is based on my experience with two UNis..one Exec and other JASJAR..both had same problem...this is how I solved :
-Put yr device in bootloader Mode
-Disable USB in Active Sync
-Now connect woth USB cable and open mtty utility
-Select the "WESUSB... " port
-You shall see a blank white screen..press Enter to get "USB>"
-Then type ( as BUzz has informed) set 14 0
(here I wud like to inform that after doing the above I did not get success so I typed set 14 10,then set 14 9 for two three times)
-Then I ran the ROM Upgrade directly(After enbabling the USB)
-I then followed the procedure as informed on the COngratulations Screen that is hold the two "-" buttons and soft reset and then pressed 0
-I got them back to normal..
I hope this helps to all my friends...Pls feel free..pls do not trouble our Buzz..he might be busy in inventing something more to our devices
Click to expand...
Click to collapse
Guru Meditation said:
I have a problem. My Exec is stuck on the bootloader screen. All I see is Serial at the top, and v1.00 at the bottom.
When I connect my exec via USB, the screen continues to say Serial (rather than switching to USB) and the PC I connect to 'installs' the device as 'unknown device' in device manager.
I've seen mention of the problem elsewhere on the site, but the only solution I can find seems to be to keep trying, and eventually it's recognised. So far, after three days of trying, it has not been recognised.
I am aware of Buzz tool to get the device out of bootloader mode, but that required a connection to be established, which at the moment, I can't do.
Has anyone got any experience of this, or any ideas as to what's causing this, or how this can be fixed? I have tried uninstalling the 'unknown device' from device manger, restarting the PC (and hard reset of the Exec) then reconnecting, but the same thing happens every time.
Just noticed your user name, I was a big Amiga fan a few years back, still fire up Amiga forever occasionally on my PC when I feel the need.
Any ideas would be appreciated, as I'm currently staring at a rather expensive paper weight.
Click to expand...
Click to collapse
Try it with a different USB cable or in a different USB port (don't go through a hub and if you've been using a laptop then try it on a desktop PC since some laptops have hubs built into them). If that doesn't work then you're out of luck as your Universal isn't detecting that you've connected to your PC and its time to send it in for repair.
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
i am stuck on the same problem and wondering the forum for almost 3 days now with no luck.... please help my device is in boot loader mood but not turning the serial to USB ......... please HELP.......
solution
Guru Meditation said:
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
Click to expand...
Click to collapse
Please follow the steps:
1. Plug in ur usb cable in bootloader mode while it is showing 'serial' and version 'x.xx'.
2. Soft reset by pressing Backlight+power+reset pin WHILE KEEPING THE USB CABLE CONNECTED
3. your phone will now reboot into 'usb' mode. Don't remove the usb cable yet.
4. Remove the Memory card while keeping the usb cable still connected and VOILA,your pc starts recognising your phone as Microsoft usb sync.
5. Do whatever you want to do now (upgrade)
Hope it solves the problem now.
Press thanks if it does.
Something else to try
Having had a few issues with my G3 Uni, I've been through my fare share of Uni bootloader issues. When I find that I can't get the 'serial' to go to 'USB', I normally find it's because I haven't taken the memory card or the SIM card out (usually the memory card).
Make sure your memory card is out, then try to enter the bootloader and see if this cures it. If it does, then use mtty and the command 'set 14 0'
This tells it to reboot on reset. if you were to use 'set 14 1' it would go back to the bootloader on reset.
my Htc hd2 t-mobile won't recognize usb on boot-loader mode
hey guys i have a big problem!!!! my Htc hd2 t-mobile won't recognize usb on boot-loader mode. Here is the story my phone was running android 2.3.7 cyanogen 7 but i wanted to update it to ics android 4.0.4, So to do that i restarted my phone while holding down the down volume button and the boot-loader with the three colors came-on saying serial but when i connect my usb cable it won't show usb. even when i tried to run the dft.exe it shows an error saying usb connection failed. BY the way it lets me access the sd card using the usb cable on my pc, so i don't know what the problem is. PLEAS HEALP i am begging u guys pleas!!!!!!!!!!!!!!
kaleb2954 said:
hey guys i have a big problem!!!! my Htc hd2 t-mobile won't recognize usb on boot-loader mode. Here is the story my phone was running android 2.3.7 cyanogen 7 but i wanted to update it to ics android 4.0.4, So to do that i restarted my phone while holding down the down volume button and the boot-loader with the three colors came-on saying serial but when i connect my usb cable it won't show usb. even when i tried to run the dft.exe it shows an error saying usb connection failed. BY the way it lets me access the sd card using the usb cable on my pc, so i don't know what the problem is. PLEAS HEALP i am begging u guys pleas!!!!!!!!!!!!!!
Click to expand...
Click to collapse
you have the wrong forum friends! This Htc Universal section
to update Android on HTC HD2, you can use the Clock Work Mod Recovery !! for more details should refer to this thread http://forum.xda-developers.com/showthread.php?t=1021837
I-MATE JASJAR hung
Guru Meditation said:
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
Click to expand...
Click to collapse
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me
bechir2013 said:
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me
Click to expand...
Click to collapse
look here
http://forum.xda-developers.com/showpost.php?p=5456317&postcount=6
the first point...
A lot easier than to root this device
Hi, my univversal is dead in bootloader at serial mode and when I connect it to my PC with usb cable it recognize it as an Unknown devices and my phone still stand in serial mode!
I was trried all the method I found like:
I went to device manager of my PC an re-install my usb--didnt work
shut down usb and active synch (with task manager) and ry mtty program-- dident work
I change my usb cable and change te mini usb gate of my phone!-- didnt work
Plz help me!!!!!!!!
god_love_power said:
Hi, my univversal is dead in bootloader at serial mode and when I connect it to my PC with usb cable it recognize it as an Unknown devices and my phone still stand in serial mode!
I was trried all the method I found like:
I went to device manager of my PC an re-install my usb--didnt work
shut down usb and active synch (with task manager) and ry mtty program-- dident work
I change my usb cable and change te mini usb gate of my phone!-- didnt work
Plz help me!!!!!!!!
Click to expand...
Click to collapse
Hi welcome to the forum.... try following
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
(try method 2)
and try to change the computer usb ports...try different usb ports of the computer and try flashing to tomals 8.5 or 8.7 ...
Cheers
Rajiv
Thank you rajivshahi for your answer and attention.
I had try all the methods that I find in hole of internet!!
also I tried your suggstted method. I was connect my phone with ans without SIM and memory to each USB port of my (and another) PCs, I changed my USB cable for several times, I also tried Uni_bootloader program and MTTY but they didn't work (because there is no USB connetion with my UNI and my PC)
I just keep crying!!!!!!
Have you tested doing Doc format?
Hope it helps,
If the device is not recognised by PC at the same time as Serial not changing to USB, I would think your USB port is no longer attached as it should and can cause the problem you described. From time to time USB port might still feel and look secure on mainboard, it will even charge the device, however, when it comes to AS and USB connection to PC, it will not connect properly.
That, or your PC USB or motherboard are malfunctioning. Try other USB devices in the same ports.
My PC's USB ports are work properly because as you told enigma1nz, I had test them with another devices
For the DOC format method: there is no USB port for connecting with MTTY!
Soooooo amazing!
(thanks for all your answers)
So, it means there is no way for me
hey,
have you disabled (unckeck) USB connection for ActiveSync/WMDC at PC?
do it now or USB port will not be available for mtty.
also please make sure that you installed XP sync driver under vista incase you're trying from vista.
follow the same -
1. unckeck USB connection for as/wmdc at pc
2. reset the device by pressing reset button
3. set bl mode (if not there already)
4. connect usb cable
5. start mtty ...
Hi Tomal, first I have to say: Thank you for your amazing roms. they are so fast, nice and stable. I'm one of the biiiig fan of your roms.
seconed: yes I was disabled the USB connection and also kill ir from task manager. but my Uni is still deeaaaaaaad
somehow I have a feeling that something is wrong with the usb port in device. may be connection is broken or something...
Hi everyone,
finally I had to send my Universal to doctor! , he says that I can load your device from SD card, and boot up it, (flashing card)
!!
I was wondered! what is flashing card! (load from SD card without any PC!)
Do any one have some information about this method!!!!
enigma1nz said:
If the device is not recognised by PC at the same time as Serial not changing to USB, I would think your USB port is no longer attached as it should and can cause the problem you described.
Click to expand...
Click to collapse
tomal said:
somehow I have a feeling that something is wrong with the usb port in device. may be connection is broken or something...
Click to expand...
Click to collapse
Yep, it does look like your device's USB being a culprit.
god_love_power said:
Hi everyone,
finally I had to send my Universal to doctor! , he says that I can load your device from SD card, and boot up it, (flashing card)
!!
I was wondered! what is flashing card! (load from SD card without any PC!)
Do any one have some information about this method!!!!
Click to expand...
Click to collapse
I believe this is the thread you are looking for
http://forum.xda-developers.com/showthread.php?t=393370
Thanks a lot enigma1nz, i think that i need but can you (or any one) explane it, step by setp for me PLEASEE !:
1. Download the tool and unrar somewhere in your pc.
2. Decode the rom image (nk.nbf) using HTC64 tool and put it (nk.nba) under the "SD_Flash" directory.
3. Run the "SDFlash_G3.cmd" and follow instruction on the screen.
SD_Flash?????
Decode the rom image (nk.nbf)???????!!
this method is for 3G, my device is 4G
This is the solution
god_love_power said:
this method is for 3G, my device is 4G
Click to expand...
Click to collapse
my dear frnd few days back i was also suffered from that problem...
And problem was with mini usb in universal.
it was disconnected with there tracks from inside.
So just open ur g4 device and resold mini usb.
trust me this is the problem.
Thanks yuvraj, how can I do it? Is there any manual for it?
can you help
You can find the manual in the Wiki, just do a search
I could'nt creat golden disk (flash from sd) cos that is for G3 devices, I just think that can we install another OS like linux on SD that is boot himself up?!
or i just have to change my universal mainboard!!!!?
Finally I beleve that my Uni is dead and I have to say goodbye to it
I'm going to buy HTC Advantage X7510, but there is one question:
Can I upgrade its WM 6.1 to 6.5 ?
I hard-SPLled my device and unpreded ROM Miri v3.0 on it. After the upgrade the device could not connect to my PC via ActiveSync or Mobile Center.
I tried with several PCs, laptops and many cables.
It should be 'soft'ware, since the problem started after ROM upgrade.
So, I figured it was because of the ROM, so downgraded to official 6.1 ROM, but connecting is still not possible. The official ROM included bootloader, radio and OS, btw.
Now I am stuck with a device that cannot connect to any PC! I always get a message of an unknown device that connects, later on followed by a message of an unknown USB device.
And yes, tried to remove the speed-up of ActiveSync. Also tried as USB storage, but I get the unknown USB device all the time...
Please help, I don't know what to try now!
Try a different USB cable. Might be a good idea to buy a brand new one. They tend to go corrupt easily.
Bright.Light said:
I hard-SPLled my device and unpreded ROM Miri v3.0 on it. After the upgrade the device could not connect to my PC via ActiveSync or Mobile Center.
I tried with several PCs, laptops and many cables.
It should be 'soft'ware, since the problem started after ROM upgrade.
So, I figured it was because of the ROM, so downgraded to official 6.1 ROM, but connecting is still not possible. The official ROM included bootloader, radio and OS, btw.
Now I am stuck with a device that cannot connect to any PC! I always get a message of an unknown device that connects, later on followed by a message of an unknown USB device.
And yes, tried to remove the speed-up of ActiveSync. Also tried as USB storage, but I get the unknown USB device all the time...
Please help, I don't know what to try now!
Click to expand...
Click to collapse
Have you tried using a differant usb port? I had to do that with a miri rom on my "old" Blackstone. I did have trouble with miri roms doing that on my Touch HD,for some strange reason.
You could also go to the threads in that forum and read what people have done to remedy that problem on the HD, as it should also work on our Tilt 2.
Later..............
Bright.Light said:
I hard-SPLled my device and unpreded ROM Miri v3.0 on it. After the upgrade the device could not connect to my PC via ActiveSync or Mobile Center.
I tried with several PCs, laptops and many cables.
It should be 'soft'ware, since the problem started after ROM upgrade.
So, I figured it was because of the ROM, so downgraded to official 6.1 ROM, but connecting is still not possible. The official ROM included bootloader, radio and OS, btw.
Now I am stuck with a device that cannot connect to any PC! I always get a message of an unknown device that connects, later on followed by a message of an unknown USB device.
And yes, tried to remove the speed-up of ActiveSync. Also tried as USB storage, but I get the unknown USB device all the time...
Please help, I don't know what to try now!
Click to expand...
Click to collapse
try rebooting your pc, also try a different usb port on your comptuer and then try another usb cable. i have read somewere that some computers do not put out enough voltage on the usb ports, so this said, after you try the previous suggestions grab your cable and try another computer, after you install activesynce of course .
Thanks for thinking with me!
I tried several PCs, so, yes, different USB ports.
Also tried several cables that proved to be ok with other devices, including one ExtUSB cable.
Of cause resetted PCs before connecting and first installing ActiveSync or Windows Mobile Center (depending on OS: WinXP or Vista)
When connecting to USB connections that worked before now sometimes the Touch tells me there is insufficient power... That's strange too! It would mean the device needs more than 500mA in some cases (because it's the only device connection to the USB) - but this is on more USB ports of different computers!
So I tried everything qua hardware... Don't know what to do now.
Bright.Light said:
Thanks for thinking with me!
So I tried everything qua hardware... Don't know what to do now.
Click to expand...
Click to collapse
Have you considered -- or tried -- flashing to a different ROM via the sd-card method? The method where you put the RHODIMG.nbh file in the root of your sd card (by removing card and using a card reader attached to PC), then put the TP2 in bootloader and it flashes the new ROM from the sd card...something like that?
I probably didn't describe this quite right -- I haven't done it myself -- but lots of people prefer this rom-flashing method. Find/check-out the procedure elsewhere on this forum.
If it works then maybe you'd get away from the problem-rom...if the rom is really the problem.
Hi, I have reflashed my ROM I dont know how many times. Yesterday I tried to connect via activesync on a new ROM and it wouldnt connect. These are some of the things that happened:
Device orange charging light flashes a few times then goes off [never seen THAT before]
Activesyc menu comes up on device but activesync doesnt connect
Get 'this device can perform faster' message on desktop
Sometimes get USB devce not recognized on desktop
SOmetimes device orange charging light it stays on if I plug direct into PC but still doesnt activesync
I have tried to connect as DISK DRIVE but I dont see the device on my PC.
Have tried different ROMS, 6.5, 6.51, sense 2.1 and 2.5 but all have same issue. Have also tried connecting to other computers. same issue.
Have played around with USB to PC menu options (enable / diable faster data sync etc) but doesnt make a difference.
Anyone had this problems? Thoughts?
Have you tried diselecting "ask me 1st about usb connection type when I connect the device to the pc" under USB to PC settings
It worked for me
This is the exact problem I am facing!
I tried everything - as diskdrive, activesync (with/without speedup), etc.
On many ROMs, even the original one (WM6.1)
Can't connect - every PC gives an 'unknown device' and on some ROMs I cannot charge via USB, only via mains...
I also tried without the question on connection.
Just some thoughts:
Do you have corruptions on screen sometimes? (Some graphical glitches)
Any .CAB files you cannot install?
Did you try to reflash the same ROM more than once?
tried to connect without card in the device and in flight mode? (Uses less power)
With me it started after a ROM flash from Miri... (I don't blame him!!)
The Hard SPL did not give me any problem, the radio was not flashed, just the OS. But reverting did not help.
I certainly hope you will find a solution, since I have the exact same problem!!
Do you stil know what ROM you flashed when this problem occured?
I reverted to original ROM 6.1 AND 6.5 which included everything - boot, radio, os, stardup image. But it did not change!
I figured it out after trying everything i could: i think its a hardware problem. I have dropped my devicetoo many times, or plugged it in too many times. Who knows.
ekerbuddyeker said:
I figured it out after trying everything i could: i think its a hardware problem. I have dropped my devicetoo many times, or plugged it in too many times. Who knows.
Click to expand...
Click to collapse
And how did you figured it out? Did you return the device to the shop?
I have this exact same issue except I am on AthineOS... I thought it was my PC until I read these posts. No OS updates or any other machine updates were performed except on my device. Any clues as to a fix?
Somehow I don't think this is just hardware.
I did drop my device once, but that was even before first flash. After that it still worked.
So, some weeks later I HSPLed without any problem. After that the device still worked.
Then, after investigating which ROM to use I flashed the ROM a few days later.
Right after the first flash it all still worked. So, had to flash another and from that moment on the device cannot be reckognised by any PC.
I still think it has something to do with the flashing. I think the device does not give correct feedback when it receives some commands from PC (eg. the command to reply the device type/number)
Does anyone know a program which can check the USB port for the HTC Touch Pro 2? Just to test wheather the connector pins are ok?
download activesync 4.5 and run the setup. it will perform a repair. that usually solves the problem. if not, try a different usb cable and try plugging into different ports on your pc.
crazythunder said:
download activesync 4.5 and run the setup. it will perform a repair. that usually solves the problem. if not, try a different usb cable and try plugging into different ports on your pc.
Click to expand...
Click to collapse
These are the first things done. And this was already written in here.
It happens with many PCs, including some on which the device never connected to.
Also tried different cables, ports, etc.
Also disabled the fast transfer etc. etc.
Even tried several other ROMs, inclusding original Dutch 6.1 and Dutch 6.5
I'm having the same issue. I can connect via bluetooth, but not usb. And I'm stuck with 6.1. I was tole my phone was brand new, but now I'm starting to think otherwise.
waynehead05 said:
I'm having the same issue. I can connect via bluetooth, but not usb. And I'm stuck with 6.1. I was tole my phone was brand new, but now I'm starting to think otherwise.
Click to expand...
Click to collapse
Some questions, to verify this is due to flashing or is a fault in the design of the device...
- Where did you get the device?
- Have you flashed the device?
- Did you accidentally drop the device?
hi just to say had a completely orignal o2 xda orbit 1 flashed with new rom everything worked perfect before now active sync plays up i can sometimes connect but get usb device not reconigsed then click cross then pull out usb then reinsert then active sync connects works fully functional then after 5 min it disconects this is driving me mad as use active sync for a fast internet connection on my pda as my wifi is crap
Good day,
I'm having problem with my DHD unable to be recognized in my Win 7 PC. I have already install HTC Sync and also tick on "Ask Me" for Connect To PC setting. I'm running on stock 3.13.707.4 ROM with S-ON and unrooted. Even restart to Fastboot my PC still unable to recognized my DHD.
From Googling it shows many Desire having USB-Brick problem, does this problem also applied to DHD? Is it my phone is hit by USB-Brick? Any guide to solve this problem? I've tried flashing older ROM via Bootloader and PD98IMG.zip but it won't allow saying something like the ROM is older version.
I just bought this used phone for about a week so I'm still not sure on how to solved this problem. any helps is much appreciated.
are you using the original cord that came with the phone? just any old usb cable won't work
also you can't flash a new rom without rooting and gaining S-OFF, you're unrooted and S-ON, that's why you get the "version is older" message
maatsby said:
are you using the original cord that came with the phone? just any old usb cable won't work
also you can't flash a new rom without rooting and gaining S-OFF, you're unrooted and S-ON, that's why you get the "version is older" message
Click to expand...
Click to collapse
I bought the phone and it came with 1 cord (with HTC label) that can be connected to the charger, I guess there are only 1 cord for charging and connect to PC? This is the cord that I use. In addition to that I have also tried Motorola, Sony Ericsson (both also for Android phone) and Nokia cord but all can't.
The ROM is actually older version stock ROM from RUU.exe. I saw from few Desire thread they were using this method to restore the ROM to before the USB Brick condition so I thought to try it.
BUMP!
Anyone know what should I do to resolve this problem?
Are you running the very latest HTC Sync on your PC? I'm using 3.0.5606. You can get it here: http://www.htc.com/www/help/
Also, connect your phone and go into Device Manager on your PC. Check to see if you have an entry for Android USB Devices and that the phone shows up. See attached screenshot for how mine looks. This is the best place to check to see if your PC has installed the drivers correctly.
In answer to your question about the cable, yes it's the same cable that attaches to the PC or to the mains charger. I've sometimes had connection problems caused by a dodgy cable, but I've used others apart from the HTC one without issues.
Edit: Also, when you install HTC Sync it should warn you to disable Antivirus software during the installation. This can be really important! I ignored it the first time around, thinking it was just a silly precaution, and had loads of problems with the phone not being recognised. Had to uninstall, temporarily disable AV, and re-install HTC Sync. Once it has finished installing, you can turn your AV back on.
Thank you for your reply preacher6.
Yes, I'm using the latest HTC Sync, v3.0.5606, just downloaded yesterday and reinstall everything.
When my phone connected to the PC it didn't appear as Android USB Device on my Device Manager, it only appear as Unknown Device in USB Controller:
So I guess I can rule out the cable as I have tried about 4 cables already.
For the installation part, I have disable the anti virus and also running the setup program as administrator. When installing there is no problem whatsoever that crop out.
Another point is, even on Fastboot it appear as Unknown Device in the PC.
I would try to update the driver manually - right click on the Unknown device, go to "install driver" or "update driver", then browse to the "Program Files\HTC\HTC Driver" folder. See if it picks up and installs the correct driver.
I've tried manually update the driver as per your advise but it says there is no compatible driver in that folder even though androidusb.inf is in that folder.
I'm running Win 7 64bit. does the driver also work for 64bit OS?
Should do, yes, I'm on Win7 64 bit myself. There is this folder on my PC:
C:\Program Files (x86)\HTC\HTC Driver\Driver Files\Win7_x64
Is the unknown device present when the phone isn't connected? Just to make sure that is actually the phone - if it's still there when the phone isn't connected, it's some other device.
Otherwise try uninstalling the unknown device and then rebooting the PC, then forcing the installation of the drivers again.
The folder is same as yours.
The unknown device does not present when my DHD is not connected, so I'm certain it is the phone that appear as unknown device.
I have tried uninstalling the unknown device > reboot PC > installing the driver but it still won't install.
Another thing is, I check on the Device Manager > Unknown Device properties > Details" for it's Hardware Ids and it shows as USB\UNKNOWN. I think it should show a strings of the device id? Correct me if I'm wrong.
Yep, there should be a proper device ID string, on charge mode mine shows a hardware ID of USB\VID_0BB4&PID_0CA2&REV_0226&MI_01.
At this point the best thing I can suggest is to try on another PC. If it works, your drivers are screwed up and you'll need to strip them and reinstall. But if it doesn't work on another PC, it's possible you have a hardware problem with the phone.
xb360 said:
Good day,
I'm having problem with my DHD unable to be recognized in my Win 7 PC. I have already install HTC Sync and also tick on "Ask Me" for Connect To PC setting. I'm running on stock 3.13.707.4 ROM with S-ON and unrooted. Even restart to Fastboot my PC still unable to recognized my DHD.
From Googling it shows many Desire having USB-Brick problem, does this problem also applied to DHD? Is it my phone is hit by USB-Brick? Any guide to solve this problem? I've tried flashing older ROM via Bootloader and PD98IMG.zip but it won't allow saying something like the ROM is older version.
I just bought this used phone for about a week so I'm still not sure on how to solved this problem. any helps is much appreciated.
Click to expand...
Click to collapse
Hi. This thread is pretty old but I'm wondering if you ever resolved the issue? I'm having exactly the same problem with my HTC One s and I can't seem to find a solution anywhere.
THanks
dmastman83 said:
Hi. This thread is pretty old but I'm wondering if you ever resolved the issue? I'm having exactly the same problem with my HTC One s and I can't seem to find a solution anywhere.
THanks
Click to expand...
Click to collapse
Yes. Holla if you still need help
marknoll said:
Yes. Holla if you still need help
Click to expand...
Click to collapse
I need help too (HTC Desire Z device)
Is it hardware problem? (I already purchased new system board).
For me it looks like hardware problem, because device does not accept bus address, do not show USB strings/VID/PID (Tried different cables/PCs/OSes (I have OpenSUSE linux, but phone does not connect to usb on any PC, Windows PCs even do not understand that something plugged in)).
No problems with USB-connector (checked resistance), but I do not see pull-down resistance with my tester.
But all other functions work well.
UPD. Tried to connect from FASBOOT/HBOOT/Android - the same result, device does not accept bus adress. Additionally it charges without problems, but when I connect phone to USB no pop-up/information at top bar appears.
FossaFX said:
I need help too (HTC Desire Z device)
Is it hardware problem? (I already purchased new system board).
For me it looks like hardware problem, because device does not accept bus address, do not show USB strings/VID/PID (Tried different cables/PCs/OSes (I have OpenSUSE linux, but phone does not connect to usb on any PC, Windows PCs even do not understand that something plugged in)).
No problems with USB-connector (checked resistance), but I do not see pull-down resistance with my tester.
But all other functions work well.
UPD. Tried to connect from FASBOOT/HBOOT/Android - the same result, device does not accept bus adress. Additionally it charges without problems, but when I connect phone to USB no pop-up/information at top bar appears.
Click to expand...
Click to collapse
I am trying to understand what exactly are you asking me . are you asking me if the PC can recognize your device ?
marknoll said:
I am trying to understand what exactly are you asking me . are you asking me if the PC can recognize your device ?
Click to expand...
Click to collapse
Sorry, it looks like I explained my question wrong (I'm Russian, and English do not native to me). Let me try reformulate:
You said "Yes. Holla if you still need help" so I believe that you were able to fix "Device not recognized" problem. So I'm asking - how did you do it? Did problem was hardware or software?
For me (look at symptoms at my previous message) it looks like dead USB controller in phone. But maybe it very strange software problem (USB-controller firmware damaged)?
Did I explain it clear now?
Install the SDK on PC and update all android versions.
Well guys it was just my PC, i made a system backup for four days and that was all the problem(the USB port of my PC)
FossaFX said:
Sorry, it looks like I explained my question wrong (I'm Russian, and English do not native to me). Let me try reformulate:
You said "Yes. Holla if you still need help" so I believe that you were able to fix "Device not recognized" problem. So I'm asking - how did you do it? Did problem was hardware or software?
For me (look at symptoms at my previous message) it looks like dead USB controller in phone. But maybe it very strange software problem (USB-controller firmware damaged)?
Did I explain it clear now?
Click to expand...
Click to collapse
After installing and updating SDK...go into platform folder and open it. Hold mouse in field and hold shift and right click mouse. Chose "open cmd here"..that will open a cmd prompt window. In regular mode on phone,type "adb devices" should return numbers (ex: hta3829g)..if in bootloader mode,type "fastboot devices" should return numbers.
This SDK helps PC see your phone when its plugged in. Especially handy when a PC won't install drivers for your phone
Sent from my ATRIX HD
Are you also stating that your device will no longer charge when plugged in?
Sent from my ATRIX HD