I recently found out I soft bricked my phone after browsing through the forums. I looked up for the solution and it turns out that I need to reset it back, no problem with that so I installed odin back again (I rooted my phone before so I had it). I first downloaded the official firmware from sammobile or some site like that and I downloaded a PIT file for my phone because the tutorial said it was essential when resetting a smartphone. I followed every step but when I launch odin and select the required tick boxes and the PDA PITi I start it. It starts up but in the middle of the loading I shows up the DO NOT TURN OFF THE TARGET!!! message and It stops.
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004>
<ID:0/004> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
This is the error and I can't seem tı get past it. I really need to deal with this quickly so if any of you have a solution, ı would appreciate it. Thanks
Anyone has the same issue? I need to fix this ASAP.
a
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Get PIT for mapping..
Now the error goes like this and nothing more.
aqertmen said:
Anyone has the same issue? I need to fix this ASAP.
Click to expand...
Click to collapse
I'm getting the exact same problem, can't fix it
Have you made any progress?
Thanks.
aqertmen said:
I recently found out I soft bricked my phone after browsing through the forums. I looked up for the solution and it turns out that I need to reset it back, no problem with that so I installed odin back again (I rooted my phone before so I had it). I first downloaded the official firmware from sammobile or some site like that and I downloaded a PIT file for my phone because the tutorial said it was essential when resetting a smartphone. I followed every step but when I launch odin and select the required tick boxes and the PDA PITi I start it. It starts up but in the middle of the loading I shows up the DO NOT TURN OFF THE TARGET!!! message and It stops.
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004>
<ID:0/004> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
This is the error and I can't seem tı get past it. I really need to deal with this quickly so if any of you have a solution, ı would appreciate it. Thanks
Click to expand...
Click to collapse
doc1975 said:
I'm getting the exact same problem, can't fix it
Have you made any progress?
Thanks.
Click to expand...
Click to collapse
Hi
Do you have a custom recovery?
Which phonemodel do you have?
U can install TWRP through Odin using a tar file. Go to TWRP and search your model, get the tar file and install it.
From TWRP u can sideload a rom using ADB.
You can push files to the phone using it, that way u can push the rom to the phone and install it through TWRP.
A long way around but worth trying when all else fail.
Related
after flashing the repencis v2.6pro it got stuck in boot screen and it wont go to recovery and i am not able to flash it with odin v1.85 it comes like this
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i did it with the dokey's kies broken frimware specified in his thread
plz help
vllskumar said:
after flashing the repencis v2.6pro it got stuck in boot screen and it wont go to recovery and i am not able to flash it with odin v1.85 it comes like this
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i did it with the dokey's kies broken frimware specified in his thread
plz help
Click to expand...
Click to collapse
Try another version. Make sure your phone is in download mode using Vol down+Home key+Power key. Flash it when the COM box is lit up after selecting PDA, Phone and CSC. Try Odin v1.84 if v1.85 fails.
raolemo said:
Try another version. Make sure your phone is in download mode using Vol down+Home key+Power key. Flash it when the COM box is lit up after selecting PDA, Phone and CSC. Try Odin v1.84 if v1.85 fails.
Click to expand...
Click to collapse
Try pressing Ctrl+Alt+Delete and go to "Processes" and search for the following process :"KiesTrayAgent.exe","Kies.exe","adb.exe"
If you seen that all in the processes of your PC/Laptop , Make sure to end that all process before proceeding up with Mr.Odin
Because mine i've flashed my DXLA1 Firmware because i always encountering SD Card issues so i ended up downgrading my DXLA1 to my Factory Firmware DXKK4
In this way , Mr.Odin helped me
vllskumar said:
after flashing the repencis v2.6pro it got stuck in boot screen and it wont go to recovery and i am not able to flash it with odin v1.85 it comes like this
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i did it with the dokey's kies broken frimware specified in his thread
plz help
Click to expand...
Click to collapse
install some other version... kill kies / adb processes... make sure ur cable is fine
got it right
there was some problem with the kies splitted files so downloaded the firmware from from another source n now got it working thx guyz
Hello,
Last night I put my phone on the charger and when I woke up it was stuck on the boot screen with the samsung logo and when I tried to restart it the screen went completely white however I can still boot into download mode. I googled it and I know what to do but the thing is when I try to flash the stock firmware it says:<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXEMC2_I9300PHNELL2_I9300CEELL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
So I tried to flash a PIT file but when I do that I get:<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
Does anyone know how to fix this??
You're on the wrong forum or attempting to Odin the wrong firmware, this is the t999 forum, that file is for the international s3
Sent from my SGH-T999 using xda premium
re: wrong firmware
joshua101 said:
Hello,
Last night I put my phone on the charger and when I woke up it was stuck on the boot screen with the samsung logo and when I tried to restart it the screen went completely white however I can still boot into download mode. I googled it and I know what to do but the thing is when I try to flash the stock firmware it says:<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXEMC2_I9300PHNELL2_I9300CEELL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
So I tried to flash a PIT file but when I do that I get:<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
Does anyone know how to fix this??
Click to expand...
Click to collapse
You are trying to flash the International Galaxy S3 9300 firmware which could brick your phone .
Start all over again and this time odin flash the Tmobile T999 stock-rooted firmware.
Here is the download link for it: http://www.androidfilehost.com/?fid=9390169635556426451
This stock firmware is pre-rooted, so no need to root.
Good Luck!
still doesnt work
Misterjunky said:
You are trying to flash the International Galaxy S3 9300 firmware which could brick your phone .
Start all over again and this time odin flash the Tmobile T999 stock-rooted firmware.
Here is the download link for it:
This stock firmware is pre-rooted, so no need to root.
Good Luck!
Click to expand...
Click to collapse
Hey thanks but it still doesn't work it still says:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_TMO_T999UVDLJA.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Try a different computer. I had to try 3 different ones until it was my daughter's laptop that finally worked. 2 computers running win7, one running vista. The laptop was running win 7.
Sent from my SGH-T999 using xda premium
Ive tried switching computers but it still gives the same error messages. Also I'm not sure if it matters but most people who have this problem say that when they boot the phone up it gets stuck at the logo screen however mine just goes white (file attached)
hey sorry for all the posts but I looked at this site
3W .droidevelopers.com/f363/11722-%5Bdownload%5D-ops-pit-files.htmll
and downloaded all three of the sgs3 PIT files but when i flash the first (GT-I9300_mx_20120220.zip) I get this:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
When i flash the second (GT-I9300_mx_20120322.zip) I get
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
and when I flash the third:
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
What can I do I'm panicking do you think there is at least a chance of it being fixed??
joshua101 said:
hey sorry for all the posts but I looked at this site
3W .droidevelopers.com/f363/11722-%5Bdownload%5D-ops-pit-files.htmll
and downloaded all three of the sgs3 PIT files but when i flash the first (GT-I9300_mx_20120220.zip) I get this:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
When i flash the second (GT-I9300_mx_20120322.zip) I get
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
and when I flash the third:
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
What can I do I'm panicking do you think there is at least a chance of it being fixed??
Click to expand...
Click to collapse
I'm sure flashing the i9300 stock rom on a T999 isn't going to do anything helpful.
I'm sure if you send it in to these guys (link below) they'd be able to fix it. I'd rather pay $60-$100 to fix my phone than buy a new one or pay what Samsung would charge to fix it (if they would).
http://mobiletechvideos.mybigcommerce.com/
|When Emotion Goes up, Logic Goes Down|
Are you using the pda section in odin
Dano79 said:
Are you using the pda section in odin
Click to expand...
Click to collapse
No when I flash the PIT file I use the PIT box should I use the PDA??
Why are you flashing a PIT file? Stop.
Stop trying to flash and international rom on your tmobile gs3. Flash the tmobile version
Sent from my SGH-T999 using xda app-developers app
When it ask for the Pit file you have to use the PIT file for the t999 and also use the PDA file at the same time.
Don't use the PIT file by itself.
Sent from my SGH-T999 using Tapatalk 2
Androiduser96 said:
When it ask for the Pit file you have to use the PIT file for the t999 and also use the PDA file at the same time.
Don't use the PIT file by itself.
Sent from my SGH-T999 using Tapatalk 2
Click to expand...
Click to collapse
There is no need for a separate pit file. Just the Odin .tar package. Please don't suggest this. I have odined this phone countless tines and I only use the .tar file for original stock image. I've never used a separate pit file nor have seen anyone here suggest it or post it in any tutorials.
Sent from my SGH-T999 using xda app-developers app
re: almost bricked
joshua101 said:
No when I flash the PIT file I use the PIT box should I use the PDA??
Click to expand...
Click to collapse
Sooner or later most likely sooner you will have hard bricked your phone
by trying to flash 9300 firmware into a t999 phone.
You need to delete all the 9300 files from your computer and
from your phone which you may have already downloaded.
Only use T999 roms, firmware, mods or any other device
specific apps and software.
What you need to do is to find the correct PIT file for your T999 Tmobile phone
and odin flash it in the PIT slot not PDA. I am certain it's here on XDA but I don't
have the time to look for it, that's something you need to do.
Only the proper PIT file will solve the problem you are having.
The PIT file will re-map your partitions so the phone will be able to
accept the odin flash stock firmware successfully.
Anything else will give you even more problems or a bricked phone.
You already messed up the partition tables on your phone already you are only
about one step away from bricking the phone.
Misterjunky said:
Sooner or later most likely sooner you will have hard bricked your phone
by trying to flash 9300 firmware into a t999 phone.
You need to delete all the 9300 files from your computer and
from your phone which you may have already downloaded.
Only use T999 roms, firmware, mods or any other device
specific apps and software.
What you need to do is to find the correct PIT file for your T999 Tmobile phone
and odin flash it in the PIT slot not PDA. I am certain it's here on XDA but I don't
have the time to look for it, that's something you need to do.
Only the proper PIT file will solve the problem you are having.
The PIT file will re-map your partitions so the phone will be able to
accept the odin flash stock firmware successfully.
Anything else will give you even more problems or a bricked phone.
You already messed up the partition tables on your phone already you are only
about one step away from bricking the phone.
Click to expand...
Click to collapse
Ooohh ****!! please help me im not ever sure what version my phone is!!! Im sorry if I have posted this in the wrong place but I got my phone as a gift and have no idea what type of phone it is all I know is that its a GT-i9300
joshua101 said:
Ooohh ****!! please help me im not ever sure what version my phone is!!! Im sorry if I have posted this in the wrong place but I got my phone as a gift and have no idea what type of phone it is all I know is that its a GT-i9300
Click to expand...
Click to collapse
But I think its an international version!
OMG so sorry for wasting your time guys I should be here right? http://forum.xda-developers.com/forumdisplay.php?f=1569
Yes use pda box only. Click on the pda box it will pull up browse option find the firmware on pc select it hit the start button rinse wash and repeat cuzo. I have never used the pit section in odin
re: wrong xda forum
joshua101 said:
Ooohh ****!! please help me im not ever sure what version my phone is!!! Im sorry if I have posted this in the wrong place but I got my phone as a gift and have no idea what type of phone it is all I know is that its a GT-i9300
Click to expand...
Click to collapse
This is the Tmobile T999 XDA Forum.
If your phone is GT9300 then you are in the wrong place, don't know why you have not found that out yet.
Here is the correct XDA forum to seek help: http://forum.xda-developers.com/forumdisplay.php?f=1563
I was trying to recover my Samsung Galaxy note 2 from soft brick status. so I tried to install new CWM recovery mode. it looks like something happened in the middle of the installation and now I started to get pit related errors in oden and the screen turned blank white when turning ON my phone.
I read in some places that I need to use new pit file to re-partition my phone. however I tried to download countless pit files from the net but none of them worked even the one I found here http://forum.xda-developers.com/showpost.php?p=31801134&postcount=4
I'm getting the same error as oden log below:
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005>
<ID:0/005> Re-Partition operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
can anyone help me please.
No reply
It looks like this is the least interesting question in the whole community, after it has been posted for more than 4 days and seen by more than 120 people no one has ever replied!!
Please guys, if you have any suggestion, Kindly dly share it.
I have bricked my S3 before and have successfully unbricked it. This time is very much unlike the last, however. To start with, I don't know what caused the brick. My S3 has been working perfectly on rooted stock firmware for several months. The day it bricked, I was using it normally and hit the power button for it to go to sleep. 3 hours later I noticed I hadn't heard any notifications and I found that my phone wasn't turning on. So for starters, I don't even know what caused my phone to become bricked.
Anywho, I located the unbrick img, booted into Linux, and flashed the image to an SD card. Popped that into the S3 and....nothing. After some searching I found there was a specific unbrick img for the new bootloader that came with the KK updates. After flashing that image to the SD and popping it in the S3 I was greeted with the "Boot Recovery Mode" which appears to transfer to Odin Mode just fine.
I open Odin 3.07 and tried flashing the factory reset tar for NJ2 and I get this:
Code:
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
So I found 2 different PIT files for my Sprint Galaxy S3 16GB. Both give me this error:
Code:
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried this in Odin 3.09 and even 1.85 just to see if any of that would magically work. Nope. I saw several users report that rebooting the phone/PC would get the PIT to flash but nothing on that front either. So I'm guessing that means the PIT files are bad but I find that a little difficult to believe. I also noticed that Odin 1.85 reports the device as "Android+SLP" and not an S3. I also read about the S3 having a problem with its eMMC and that it would need to be shipped away for motherboard surgery. So I'm prepared to call the time of death on this phone but I figured I would give one last ditch attempt by presenting my situation to the genius collective of XDA. Any suggestions?
SOLVED SOLVED SOLVED
JUST FLASHED THIS BPH4 https://drive.google.com/file/d/0B_gPYnMt2KosdGxGQXY1bzFjSE0/view
---------------------------------------------------------------------
Guys, anyone knows how to come out from this? Please...
EDIT:
Here is what odin says.
<ID:0/009> Odin engine v(ID:3.1100)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Removed!!
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> SingleDownload.
<ID:0/009> sboot.bin
<ID:0/009> NAND Write Start!!
<ID:0/009> RQT_CLOSE !!
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
EDIT 2:
If i flash BL from N920AUCU1AOGG stock rom i receive
<ID:0/009> Odin engine v(ID:3.1100)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Can't open the specified file. (Line: 2012)
<OSM> All threads completed. (succeed 0 / failed 1)
EDIT 3:
Reflashed the same bl with the pit file from csc, and this..:
<ID:0/009> Odin engine v(ID:3.1100)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> SingleDownload.
<ID:0/009> sboot.bin
<ID:0/009> NAND Write Start!!
<ID:0/009> param.bin
<ID:0/009> FAIL!
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Don't flash the bootloader.
Please help me, i bricked my phone
It doesn't go beyond, samsung logo,
I tried to flash OJ1 firmware again using Odin, then i tried to updraded but failed twice. Now i am unable to boot at all.
I am able go to download mode but can't go to recovery. even after reflashing stock rom i stuck in samsung logo and cn't go beyond and can't go to recovery. but able to go to download mode. Please help.
Please help me how can i repartition my At&T glaxy note 5 and get the PIT file and other stuff for AT&T version of note 5. I shall be very very thankful.
Please help .....what to do now.
dradil said:
Please help me, i bricked my phone
It doesn't go beyond, samsung logo,
I tried to flash OJ1 firmware again using Odin, then i tried to updraded but failed twice. Now i am unable to boot at all.
I am able go to download mode but can't go to recovery. even after reflashing stock rom i stuck in samsung logo and cn't go beyond and can't go to recovery. but able to go to download mode. Please help.
Please help me how can i repartition my At&T glaxy note 5 and get the PIT file and other stuff for AT&T version of note 5. I shall be very very thankful.
Please help .....what to do now.
Click to expand...
Click to collapse
Download the file i linked give a try
Kundinga said:
Download the file i linked give a try
Click to expand...
Click to collapse
Thank you so much. I have downloaded the file. and tried to update it and i was able to flash it and phone booted well, but it restarts again and again. it happens with all the file. Thank you so much for this atleast phone booted. I loaded all the 4 files except the PIT file.
Should i also try to load the PIT file? How to load a PIT file what should i do, should i check the partition option in ODIN with PIT file. What should i do, is it any solution? of this restart again and again, i also tried to wipe cache in recovery, now my phone is able to run into the recovery.
Thanks a million time.
dradil said:
Thank you so much. I have downloaded the file. and tried to update it and i was able to flash it and phone booted well, but it restarts again and again. it happens with all the file. Thank you so much for this atleast phone booted. I loaded all the 4 files except the PIT file.
Should i also try to load the PIT file? How to load a PIT file what should i do, should i check the partition option in ODIN with PIT file. What should i do, is it any solution? of this restart again and again, i also tried to wipe cache in recovery, now my phone is able to run into the recovery.
Thanks a million time.
Click to expand...
Click to collapse
Put every file in his right section and load the pit, in Odin there is a menu hidden by a button on the left, one of the three let you load the pit (now I don't remember very well the interface hahah give a try)
Kundinga said:
Put every file in his right section and load the pit, in Odin there is a menu hidden by a button on the left, one of the three let you load the pit (now I don't remember very well the interface hahah give a try)
Click to expand...
Click to collapse
Thank you once agian for the reply.
Should i check the "re-partition option" after loading the PIT and then Start?